Troubleshooting - SD Fire Alarms
Contents
1. Troubleshooting The units red LED does not flash when the batteries are installed Ensure the batteries are connected correctly according to the diagram in the battery compartment The red light keeps flashing This is the low battery indicator Replace the unit s batteries Radio ON OFF The radio is default to be always on It is possible to disable the radio function if you are using just a single device in order to conserve power To turn ON radio Enter your 4 digit PIN followed by 2 1 1 1 1 To turn OFF radio Enter your 4 digit PIN followed by 2 Yale Yale Yale Yale Factory reset If you forget your PIN or the system malfunctions you can press the reset button locates behind battery cover to erase all memory Please ensure the device is powered and system is in Disarm mode After reset you will need to set up your PIN again and pair with other devices if required Battery precautions When using this product follow these precautions at all times e Use only the appropriate size batteries e Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Incorrect polarity may Cause damage to the unit e Do not mix old and new batteries e If the alarm is not used for long periods of time remove the batteries to prevent damage to the unit or injury from possible battery leakage e Do not recharge batteries not intended to be recharged Always foll2. learner unit to which you are pairing 6 To confirm the units are paired the learner unit will have Red LED on constantly indicates units in contact and will beep once afterward Only release after you hear this beep 7 Repeat this contact for all other learner units you want to pair with the teacher unit 8 After the 2 minutes sending mode the main unit will return to disarmed mode The red LED will flash 3 times to confirm 9 If you wish to exit the learning mode within the 2 minute duration press CLR button twice on the teacher unit to exit
3. ow the manufacturers directions e Please only use alkaline batteries Wireless range If using as part of an extended system the range of these parts is a minimum of 1 meter up to a maximum of 25 meters System activity Please note when the red light is on the product is processing so no operation will work for example you will not be able to enter your PIN WEEE Note Waste electrical products should not be disposed of with household Yal waste Please recycle where facilities ale exist Check with your local authority or School Street Wil lenhall retailer for recycling advice West Midi ands WV13 3PW Tel 44 0 1902 364606 Fax 44 0 1902 364692 email info yale co uk www yale co uk An ASSA ABLOY Group brand ASSA ABLOY E1 09 08 SAA8021 Wirefree mini siren User Manual Keep this manual safe for future reference An ASSA ABLOY Group brand ASSA ABLOY Product diagram 1 Front eyebrow contacts 2 LED 3 Siren 1 Battery compartment 2 Reset button Battery installation The battery compartment is located on the rear of the alarm unit It can be accessed by removing the screw from the back of the unit and lifting the cover Insert 4 AA Alkaline size batteries not included as shown diagram When the last battery is inserted the centre red LED will flash 3 times Replace the back cover and fix with screw NOTE Please wait 30 seconds before inserting new bat
4. teries whenever you take old batteries out Installing the unit The unit has been designed to be either free standing or wall mounted To wall mount 1 Place the alarm in the desired location Care and maintenance To clean the unit simply use a soft slightly damp with water cloth and wipe dry immediately Caution Never use chemicals to clean the unit as this may cause damage to the plastic and result in the alarm not functioning Pairing the siren with another unit from the range The standalone alarm range has been designed specifically to operate as single units or be paired together to work as kits Up to 3 of the master units those that have sensors as well as sirens can be paired together The number of slave units those that do not have sensors that will work together is limitless This siren alarm is a slave unit Each master unit has a unique radio code which can be sent to any other unit in order to make them work together The procedure for doing this is as follows 1 Starting with any master unit which you want to be the main teacher unit for the system 2 Enter your PIN code and then press the Yale button afterward 3 The LED will flash in the sequence green orange red 4 The unit is now in sending mode for the next 2 minutes The green and orange LED will flash every second 5 Hold the rear metal contact points of the main unit against the eyebrow contact points of the
Download Pdf Manuals
Related Search