installation - Multicare Electronics Ltd
Contents
1. 6 7 8 ghts OUD Or o Set for outdoor light 6500 K SETTING 6 7 8 5 T Changes the switch settings for EY SW 1 SW 3 to change the electronic shutter speed At this time the actual Flickerless and 1 On Backlight Compensation are ignored and the iris function is fixed A O off This function is off 1 When the electronic shutter speed setting is set to ON a combination of the following three switches can be used to set up to eight speed levels Unit seconds Shutter speed Switches AN Shutter speed Switches Hy 1 50 dd E O 1 1000 g g 0 1 2 3 1 2 3 Ooo Oo O O 1 120 0O 1 2000 1 2 3 1 2 3 OI 1 250 0 DO o 1 4000 0 O 1 2 3 1 2 3 1 500 g g g 1 10000 E g O 1 2 3 1 2 3 NOTE Using the high speed electronic shutter indoors with low lighting will give darker pictures In such a case add some lights to make sure the lighting is sufficient Gamma compensation For adjusting the gamma compensation use this setting to adjust the signal correction contrast so that the image looks natural 8 2 7 Gamma is set to 0 6 Makes the gamma compensation stronger High than the default low setting a O Low Gamma is set to 0 45 2 Sync adjustment Only when using an AC 24 V power supply Synchronizes the camera with power freq2. large 1 Hexagon wrench medium 1 Hexagon wrench small 1 Cushioning sheet 4 1 Appearance and specifications are subject to change without prior notice PRECAUTIONS E In case of problem Do not use the unit if smoke or a strange odor comes from the unit or if it seems not to function correctly Turn off the power immediately and consult your dealer or an Authorized Sanyo Service Center E Do not open or modify Do not open the cabinet except during adjustment as it may be dangerous and cause damage to the unit For repairs consult your dealer or an Authorized Sanyo Service Center E Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the unit If used with a foreign object inside it could cause a fire a short circuit or damage E Be careful when handling the unit To prevent damage do not drop the unit or subject it to strong shock or vibration E Install away from electric or magnetic fields If installed close to a TV radio transmitter magnet electric motor transformer or audio speakers the magnetic field they generate may cause image distortion E Protect from humidity and dust To prevent damage do not install the unit where there is greasy smoke or steam where the humidity may get too high or where there is a lot of dust E Protect from high temperatures Do not install close to stoves or other heat sources
3. English Fran ais Deutsch A Et ie SANYO INSTRUCTION MANUAL VDC C1175VP COLOR CCD Camera About this manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for later reference Approvals IP66 CE This unit has been certified to IP66 standards when properly installed Use only an IP66 certified enclosure or an electrical box Ensure all openings in enclosure are sealed as per manufacturer s instructions Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer TROUBLESHOOTING Before sending the camera out for repair check the items below If the problem persists after checking these items consult your dealer or an Authorized Sanyo Service Center E If no image appears Is the coaxial cable attached securely Are the power and voltage normal Is there adequate illumination E If the image is unclear Is the lens in focus Is the lens dirty Dirt or fingerprints on the lens can adversely affect the image Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid commercially available Is the monitor adjusted correctly SERVICE The camera is a precision instrument Handle it carefully and always fo
4. east 35 mm and 3 5 5 mm into the ceiling or the wall If the screw holes are too shallow the camera may fall down In addition do not touch the camera unit except when settings and adjustments are necessary Install where the temperature range will stay between 10 C 14 F and 50 C 122 F no condensation 1 Use the supplied hexagon wrench large to remove the four fixing screws B of dome cover A Make screw holes and a cable hole in the supplied cushioning sheet D that attaches to the back of the camera unit C Attach the cushioning sheet single sided tape to the back of the camera unit Align the camera unit with the surface of the ceiling or the wall make marks on the ceiling or the wall in the places where the screw holes are to be drilled and then drill the four holes 5 Cuta hole in the ceiling or the wall for routing the cables KR QO N caution If not routing the cables inside the ceiling or the wall open the conduit hole cover F after removing a screw E by supplied hexagon wrench medium and pass the cables through the conduit hole 6 Pass the power cable G and video cable H from the camera unit through the cable hole in the ceiling or the wall 7 Align the four screw holes in the camera unit C with the screw holes in the ceiling or the wall and then secure the camera in place by tightening the four or more screws I through the washers 8 Secure the dome cover A by tight
5. ening the screws B 9 Carry out the settings and adjustments for the camera Refer to CONNECTIONS AND SETTINGS for camera settings and lens adjustments 10 If the dome liner K is secured in place loosen the screw J Adjust the dome liner K so that the dome camera s lens is visible from the camera window L and then use a phillips screwdriver to fix the dome cover CONNECTIONS AND SETTINGS E CONNECTIONS DC 12 V AC 24 V connection CAUTION Check for polarity when using a DC 12 V power supply Polarity does not matter when using an AC 24 V power supply E LENS ADJUSTMENTS 360 Pan Screw B 5 A Screw B FOCUS ZOOM 80 80 Tilt E CHECKING THE CAMERA IMAGE You can use the monitor checking cable sold separately to display an image on a monitor when setting up the camera to check the surveillance angle and range lens focus etc Connect the connector of the monitor checking cable to the monitor checking connector A on the circuit board and connect the jack of the monitor checking cable to the monitor E LENS ADJUSTMENTS Once the camera has been installed adjust the lens section caution Be careful not to touch the lens section when changing the angle of the camera 1 Adjust the pan position 360 and the tilt position 80 2 Loosen the zoom lever screw turn the zoom lever to the right left to determine the zoom position w
6. he high brightness object or as a perpendicular band In such a case adjust the angle of illumination and other factors while observing the monitor If fluorescent lighting is used where the camera is installed the object will flicker as a result This type of phenomenon can be avoided by replacing the fluorescent lighting with incandescent lamps E CAMERA SETTINGS The camera comes pre adjusted and ready to install at time of factory shipment but you may want to make settings to adapt to the operating conditions or installation environment If you have trouble adjusting the camera consult your dealer or an Authorized Sanyo Service Center Factory default setting Flicker compensation O 1 Corrects screen flickering that occurs when positioned under On fluorescent lights that use a 60 Hz power supply frequency C off This function is off 1 NOTE Even if flickerless is set the iris function will be fixed Backlight compensation A Electronic shutter speed setting H When an image On is backlit O Off This function is off 2 Gain control K For adjusting the sensitivity of the camera Use this setting for shooting in dark environments O Increased sensitivity allows shots to be taken in dark High 26 dB environments This setting causes noise generation and a grainy image I Low 20 dB Sor inis w
7. hen there is excessive noise in the high setting Color compensation White balance A Adjusts the balance of colors When AUTO TRACKING WHITE BALANCE default setting does not work properly select other settings AUTO TRACKING g E g z F WHITE BALANCE Automatically adjusts the white balance 6 7 8 AUTO WHITE g g Automatically adjusts the white balance BALANCE when the object is near oO Fine tunes the white balance manually Adjust the color using buttons Left Red Right Blue If an AC 24 V power supply user sets MANUAL WHITE BALANCE sync adjustment cannot be performed To perform sync adjustment do it with buttons before setting MANUAL WHITE BALANCE MANUAL WHITE BALANCE o0 E 0O Adjusts the white balance when the a oO O brightness is constant After setting the 6 WHITE BALANCE LOCK switch at left keep pressing the white 7 8 balance lock button J until the desired tint is achieved and release it to set Set for indoors when the room is lit by fluorescent or incandescent lights 3200 K INDOOR SETTING LIGHT 1 o O iO 0 INDOOR SETTING Set for indoors when the room is lit by gt o TI s0 0 LIGHT 2 fluorescent lights 4200 K INDOOR SETTING 0O O go Set for indoors when the room is lit by LIGHT 3 fluorescent lights 4700 K
8. hile viewing the camera images on the monitor and then re tighten the screw 3 Loosen the focus lever screw turn the focus lever to the right left to detemine the focus position while viewing the camera images on the monitor and then re tighten the screw NOTE on image direction If the monitor image is misaligned follow the steps below to adjust Loosen the screws B with the supplied hexagon wrench small Turn the indented dial to adjust the image direction Tighten the screws B after adjustments are finished Monitor checking connector A CAUTION When using an RG 59U 3C 2V cable do not use it on piping or air wiring Select the cable according to the distance between the devices you wish to connect If you use a cable other than the types above the image or sync signal will be attenuated and will not be transmitted correctly Supported coaxial cables You can use any of the following coaxial cables RG 59U 3C 2V Length 250 m max RG 6U 5C 2V Length 500 m max RG 11U 7C 2V Length 600 m max E CAMERA SETTINGS Board on the same side as the lens Board on the opposite side of the lens NOTE When monitoring lighting or other extremely bright objects which exceed the maximum required illumination smearing may occur in the vertical or horizontal direction either above and below t
9. llow the safety precautions If the camera requires service never try to repair it yourself or open the casing For servicing maintenance or repairs consult your dealer or an Authorized Sanyo Service Center MAIN FEATURES m Complies with IP66 international rating E Ceiling Wall mount housing E Built in vari focal lens E 1 3 inch solid state image device CCD E Number of total pixels 470 K pixels E Internal sync Line Lock automatic swichable m Dual power supply AC 24 V DC 12 V lead wire E High sensitivity minimum required illumination 1 0 Ix at F2 0 lens Dimensions mm SPECIFICATIONS Scanning system PAL standard TV system 625 TV lines 25 frames s Interlace PLL 2 1 interlace Image device 1 3 inch solid state image device CCD Number of pixels in 752 H x 582 V 440 K pixels image area Sync system DC 12 V user Internal sync AC 24 V user Line lock 460 TV lines horizontally Video output level 1 0 V p p 75 Q composite Image S N ratio More than 46 dB at gain control off Pan Tilt adjustment Pan 360 degrees Tilt 80 degrees Lens Built in variable focal lens f 4 8 mm F2 0 2 8 Operating Temperature 10 C 50 C 14 F 122 F environment Humidity less than 90 RH no condensation Power supply AC 24 V 10 50 Hz DC 12 15 V 10 Power consumption 2 8W Resolution Weight Approx 1 6 kg Accessories Hexagon wrench
10. such as spotlights etc or where it could be subject to direct sunlight Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may rise to high levels E Cleaning Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then dry by wiping with a soft cloth Do not use benzine thinner or other chemical products on the cabinet as this may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes into contact with the cabinet for a long period of time as this may cause damage or paint peeling E Mounting Surface The mounting surface material must be strong enough to secure the unit Plasterboard without a backing plate is not recommended SANYO SANYO Electric Co Ltd Printed in Korea L5QC2 XE3 0604TR CP INSTALLATION CD CAUTION When installing the camera to the ceiling or the wall make sure to properly perform waterproofing for the holes in the ceiling or the wall When setting up this camera make sure that it is installed securely Check that the installation location is strong enough to bear the camera before proceeding Install to the ceiling or the wall with no unevenness in its surface And be sure to embed the screws at l
11. uency when two or more cameras are connected via a switcher unit When the image on the monitor rolls vertically adjust the phase A If using this unit as the second or subsequent camera O CJ Adjust the roll by pressing each button B If using this unit as the first camera Adjust the roll using the phase adjuster on the second and subsequent cameras NOTE When using an AC 24 V power supply to connect the camera to a monitor internal sync is set The phase adjuster does not function When using a DC 12 V power supply the sync setting is set to internal sync If MANUAL WHITE BALANCE is set sync adjustment cannot be performed Change to a different white balance setting and adjust the sync And then set MANUAL WHITE BALANCE again
Download Pdf Manuals
Related Search