infraNOMIC Heating Panels
Contents
1. Operation General Instructions The Heating Panels incorporate a built in Safety Cut Out Switch so that when overheated by abnormal use for e g by covering the heater the Heating Panel will automatically switch itself off Through removing the power to the heater and allowing a period of approx 10 to 15 minutes to elapse the safety cut out switch will automatically reset itself After rectifying the problem that has caused the overheating and by connecting the power the Heater is again ready for normal operation Connection to the Power Supply Every infraNOMIC Heating Panel is supplied with a cable and plug Connect the panel via its plug to a normal household socket carrying a 230 240 V 50 Hz alternating current The Panel can also be used in conjunction with a room temperature regulator thermostat that can be separately purchased as a Plug In device to fit between the socket and the Panel s plug or alternatively a room thermostat can be directly fitted to the house circuit through which the power to the heater is fed and controlled Similarly the Panel can be used in conjunction with a timer which would control the ON or OFF times of the heater ATTENTION It is important that the above mentioned controllers thermostat or timers if used are suitable and can accommodate the power consumption of the Heater The power consumption of your heater is included in the information on the nameplate of the heater to be fo2. al is recyclable Please make sure that this is disposed of correctly A ATTENTION Make sure that the packing material is kept away from babies and small children as suffocation can result if placed over their mouths or noses Installation ATTENTION Please read the section regarding Basic Rules for Safety and details involving the Installation location the information regarding safe distances and the Operation of the Panel Please take note of the following additional information with regards to installation The minimum dimension from the back side of the panel to the wall or ceiling must be 2 cm This will always be the case if the items contained in the accessories are used If other types of fitting systems are used our guarantee becomes null and void The hot side of the heater is always the side with the sticker that says infraNOMIC Infrarot Heizelement Nicht abdecken This sticker should always be visible after installation Check before drilling holes that there are no electrical lines or water pipes hidden in the wall Make sure that the power supply socket that you intend to use is within distance of the location of where you intend to install the Panel The cable attached to the panel is 1 7 m long With difficult walls it may be necessary to use special rawl plugs When the Hooked Mounting Screws are screwed into the wall it is important that they are screwed in right up to the flange Wall Instal
3. el cannot be easily removed from its position Ceiling Installation ATTENTION Please read the Parts included section on page 3 regarding the Ring Screws G The decision of what attaching devices are to be used for ceiling mounting is dependant on the type of material the ceiling is constructed with and also the ability to support the weight of the Heating Panel if already fitted remove Bolts C and Hanging Plates B from the heater Screw the 4 Ring Screws G into the integrated nuts and move these as far as practically possible towards the corners of the frame in a uniform manner These can be then hand tightened e Measure the distances between the Ring Screws both from the short and long sides of the frame and transfer these measurements onto the ceiling where the panel is to be installed A diagonal measurement will help to insure that the panel will be parallel e Screw 4 further Ring Screws into the pre determined positions Depending on the construction of the ceiling it may be necessary to pre drill holes and fit with Rawl Plugs Arrange the ceiling screws in the same direction as those on the panel e Install the Heating Panel by connecting the Ring Screws on the panel to those on the ceiling with a connecting device such as for example a karabiner clip Installation of Frameless models Special Installation Instructions and accessories will be included for Frameless models when these are specified
4. f as household rubbish but should be returned to the manufacturer for correct disposal see Service address Through re cycling of materials or of old machines you are providing help which is important to protect our world from unwanted rubbish Technical Data Operating Voltage 230 240V 50 Hz alternating current Power Consumption 200 750 W see Data page Protection Class II E Dimensions Weight see Data page The dimensions given are for the actual glass sizes the size of the frame is additional With M 10 these are approx 5 mm in the width and height With M 23 these are approx 55 mm in the width and height With HB 30 these are approx 30 mm in the width and height With Frameless models the tolerance of only the glass is taken which is 2 mm Technical details of all current models are listed in the Data Page see page 8 The units comply with the test requirements of the European Low Voltage specifications 2006 95 EG and the harmonised Product Standards EN 60335 1 and EN 60335 2 30 and are marked with a CE Conformity Label Guarantee and Service The Heating Panels are guaranteed by Wolff amp Meier for 2 years after the purchase date If these Operating and Installation Instructions are followed and are correctly adhered too we guarantee the free of charge replacement of the Heating Panel if the problem occurring is directly related to a manufacturing or material fault If however the problem has been caused b
5. hildren and Persons with disabilities 0 eee eee ee eeeees 2 Electrical Safety as6d lt telobeuiactacnaceccensancuceucausadeeaceanecsacean 2 Product Safety notes occ ec ece eee eee eee eee ee eee eaeeeeeeeeeeneaeeseeaneanes 2 Suppi and Parts Included sasteedseeicoriesnie E E iS 3 ASO a E noua aimee peRuad 4 VW AIRAIISEAMEION O Ea a ai 4 Ceiling Installation j Aissheserrcisrkedeesscseaneue ue ashauen cna uesedanenucuss 5 Installation of Frameless models sisekesessniereernecehinr eames eee 5 Operation tiie er eth E et etan cs 6 Generallnstructions sgseutersiocncstcste cesses uteeseoceestcsen Genet ct enekoent 2 6 Connection of Electrical Power aaselede iddceci aie adie e icecoeeneaeeecee es 6 Tips for correct use qj piceuicccchons sadhiauiivedantndacgswe pnieaueerasdusaeewsenas cane 6 IGANG Rah keene S a a eG cant 6 ISOOGA Seater ere ara ae ane en anor eres eed a T Tecnica Data O Se Pe eC ne ee ee eer ees eee eee 7 Guarantee and Service atv veed pester wien ac needeuuentannedginmanagneenreeeeeads 7 Data Page of infraNOMIC Heating Panels cccceccecee eee ee teas ea eeeee eee eneeeaeeeeenaees 8 Basic Rules for Safety USE The infraNOMIC Heating Panels are designed only for use as heaters and are suitable for installation on Walls or Ceilings in domestic or commercial rooms which are suitable for their installation To use these heaters correctly it is necessary to follow the guideli
6. infraNOMIC INFRARED HEATING PANELS Operating and Installation Instructions Installation Instructions only for Framed Panels Woltf Meier GmbH amp Co KG Glaswerke Am Wingert 16 35428 Langgons Germany Thank you for your purchase Dear Customer You have bought a high tech innovative heating product InfraNOMIC Heating Panels work with Infrared technology They have low energy consumption and create a pleasant atmosphere in each room where they are installed With the correct installation and operation youre Heating Panel will give you satisfaction for many years to come Please read completely the Operating and Installation Instructions before you start to install the panel and pay particular attention to the safety instructions These Operating and Installation Instructions will help you safely install and use the panel in the most efficient way Please make sure that you use the heater exactly as per the following instructions the adherence to these instructions is a pre condition to the manufactures liability regarding any guarantee cases After completion please store these instructions in a safe place so that they can be used again if necessary and also can be given to another user if the panel changes hands Contents Thank youTor your purchase iewenturieieeaiine ew siwesceuaiianes cursetweceet 1 GONER OOO aR ARASEN 1 Basie Rules Tor salei 6 eee en eee en eee 2 Use E E E E EE E T E E 2 Danger for C
7. lation The Hanging Plates B should be attached to the shorter side of the heating Panel for vertical Installation and on the longer side for a horizontal installation The plates are attached by using the Bolts C 2 bolts per plate e make sure that the corner of the panel where the cable is attached is not used for mounting the plates e and that the slots in each of the plates are mounted in the same direction see picture e and that the bolts C are only hand tight so insuring no damage to the frame Screw the two bolts D into the integrated nuts found in the opposite side of the frame from where the plates are attached These bolts insure the correct distance from wall to the back of the panel is adhered too Measure the distance X between the slots and transfer this measurement to the wall where the panel is to be installed Use a Spirit Level to insure that the marks for drilling are level Drill each of the holes with an 8 mm drill to a depth of minimum 60 mm Insert the Rawl Plugs F into the holes make sure that both are fully inserted These plugs can be used universally even for wooden walls Screw in the Hooked Mounting Screws E up to the flange making sure that the hooked part of the screw is vertical Lift the Heating Panel onto the Hooked Mounting Screws and then slide it to one side insuring that both screws are located in the dogleg part of the slots This insures that the Heating Pan
8. nes and instructions laid down in this document DO NOT use the heaters in rooms that are open to the elements and or rooms which could be subjected to the ingress of running water Danger for Children and Persons with disabilities These products are not to be installed by people including children who are physically or mentally handicapped unless a competent person who can provide help and instruction is present Be sure that children do not play with or use the heaters as a toy Make sure that the packing material is kept away from babies and small children as suffocation can result if placed over their mouths or noses Electrical Safety Connect and run the heater according to the advice given on the specification plate on the rear of the heater Only connect the heater to a 230 240 V AC supply grid Check each heater for damage before installation Make sure that the heater itself its plug and cable are free of any visible signs of damage ATTENTION The Heating Panels should not be used if the Glass or Ceramic backing is damaged If damage is noticed immediately disconnect the Panel from the Power supply and contact our Service department Do not pull clamp or in any other way damage the connecting cable attached to the Panel If the attached connecting cable does appear to be damaged please refer to the manufacturer or his service department or a similarly qualified person to undertake any repair work Do no
9. t Weight Weight 900x600mm 96 500 14 6 21 8 ca 10kg ca 10 kg ca 11 kg ca 13 kg 1100x600mm 116 600 21 9 259 ca 11kg ca 11 kg ca 13 kg ca 16 kg ca 10 kg 1200x600mm 126 700 26 34 ca 12kg ca 12 kg ca 13 kg ca 17 kg ca 11 kg Heating Panel Coloured a Type GHE RAL M10 X M24 X HB30 X P RL X Size of Aluminium Aluminium Power Wooden Frame Frameless Frameless SL Room to be Frame Frame Solid Beech Glass Backin Metal Backin heated 10 mm 24mm g g X Watt ca m3 Weight Weight Weight Weight Weight 1100x 600mm 116 600 21 9 25 9 ca 10kg ca 10 kg ca 12 kg ca 16 kg ca 10 kg 1200x600mm 126 700 26 34 ca 11kg ca 11 kg ca 13 kg ca 17 kg ca 11 kg Heating Panel Art Picture and Stone a Type GHE MDS M10 X M24 X HB30 X P RL X Size of Aluminium Aluminium Power Wooden Frame Frameless Frameless SL Room to be Frame Frame f j Solid Beech Glass Backing Metal Backing heated 10 mm 24 mm X Watt ca m3 Weight Weight Weight Weight Weight 1100x 600mm 116 600 21 9 25 9 ca 10kg ca 10 kg ca 12kg ca 16 kg ca 10 kg 1200x600mm 126 700 26 34 ca 11kg ca 11 kg ca 13 kg ca 17 kg ca 11 kg
10. t attempt to carry out any repairs changes or modifications to the Heating Panel Before any assembly or cleaning work is carried out disconnect the Panel from the electrical power Do not immerse the Heating Panel in water or splash water onto it When installing the Panel in any form of wet room it and its cabling should be situated well out of reach of any person using the shower or bath Do not install the Panel in close proximity of a bath shower or swimming pool The installation of these panels in wet rooms should always be carried out by competent electricians who are completely aware of the specifications for installing electrical equipment in these types of room according to their own countries laws and standards Product Safety Notes ATTENTION To insure that the Heating Panel does not overheat it should not be covered in any way The Panel should not be installed directly under a plug socket Do not rest anything against or use the Heating panel to dry clothes and or stick anything onto its surface Make sure that all local objects in the immediate vicinity of the heater are a minimum of 50 cm away from the front and sides of the panel and 10 cm away when objects are above Make sure when installing the Panel that the minimum distance of 2 cm between the Wall or Ceiling and the Panel is adhered too This distance insures that enough space is available for air circulation Supply and Parts Included Af
11. ter being thoroughly tested at our works the heating panels are safely packed and despatched with a reputable transport company When your product arrives please check the outside appearance of the packing for any signs of damage If you believe that the package is damaged in any way please ask the delivery person to wait while you unpack it and check the state of the goods within for damage If possible keep the panels and accessories in the original packing until you decide to install the product A After unpacking the goods please check and make sure that all of the following listed parts are included and are not damaged 1x Heating Panel with Cable A 1x Accessory Set which includes 2 x Hanging Plates B E Aa oe or 4x Bolts M6 x 8 C ca spa aQ T 9 2x Bolts M6 x 25 D oe j 2 x Hooked Mounting Screws E I AP 2x Rawl plugs 8mm F E 4x Ring Screws M6 for Ceiling Mounting G B D E F G 1x Operating and Installation Handbook If you discover that any parts are missing or are damaged please contact the company where you purchased the product or contact our Service department The Ring Screws G are not an integral part of the standard accessory pack When ordering the heater it should be specified where and how you intend to install it e g Wall or Ceiling this will then insure you receive the correct accessory pack for your requirements The packing materi
12. und on the back of the panel Tips for correct use When the Heater is turned on at first it is possible that for a short while you may be aware of a distinct sweet smell This is not harmful to health and if present is caused by the vaporisation of silicon in contact with the MDF backing board This will cease after a short while To heat a room that has not been heated recently or one which is very cold it may be necessary to run the heater without a break for some time This will insure that all solid cold objects furniture walls ceilings floors etc are initially warmed After these solid objects are warmed the radiated heat coming back from them will divide its energy evenly throughout the room and allow the heater operating time to be reduced to a minimum The function of radiated heat helps through its very low power consumption to protect our world and its resources Cleaning ATTENTION DANGER OF ELECTRIC SHOCK Before attempting to clean the Panel unplug the heater and allow it to completely cool down Do not immerse the Heating Panel in water or splash water onto it Clean the glass or ceramic surface and also the frame with a damp cloth and glass cleaner When clean dry the surfaces with a dry cloth Do not use strong chemical removers to clean the heater nor implements with sharp edges uses of these could damage the surfaces of the heater Disposal The Heating Panels or parts of them should not be disposed o
13. y incorrect installation or operation the free of charge guarantee becomes null and void Your personal rights regarding this guarantee are not diminished Service Address Isolierglaswerke Wolffe amp Meier GmbH amp Co KG Am Wingert 16 35428 Langg ns Germany Telephone 0049 0 6403 9006 0 Fax 0049 0 6403 9006 15 E Mail infranomic wolff meier de Version 0 5 2009 05 20 Eng Data Page of infraNOMIC Heating Panels The complete Panel designation is built up based around the Heating Panel Base type the Frame type and the size Example GHE S M24 96 is a Mirror Heating Panel with a Aluminium Frame 24 mm with a size of 900 x 600 mm The operating voltage for all Heating Panels is 230 V 50 Hz Heating Panel Standard Black or White a Type GHE P M10 X M24 X HB30 X 2 RL X Size of Aluminium Aluminium Power Wooden Frame Frameless Frameless SL Room to be Frame Frame Solid Beech Glass Backin Metal Backin heated 10 mm 24mm g g X Watt ca m3 Weight Weight Weight Weight Weight 1100x 600mm 116 600 21 9 25 9 ca 10kg ca 10 kg ca 12kg ca 16 kg ca 10 kg 1200x600mm 126 700 26 34 ca 11kg ca 11 kg ca 13 kg ca 17 kg ca 11 kg Heating Panel Mirror a Type GHE S M10 X M24 X HB30 X P RL X Size of Aluminium Aluminium Power Wooden Frame Frameless Frameless SL Room to be Frame Frame i Solid Beech Glass Backing Metal Backing heated 10 mm 24 mm X Waitt ca m3 Weight Weight Weigh
Download Pdf Manuals
Related Search