red shield key fob remote control installation and
Contents
1. g If 3 remotes are enrolled the LCD display will flash 03 The ID No of the Remote can then be checked by pressing any key on the remote e g if the LCD display flashes 02 then that is the ID of the remote Evren Press enren Evren to complete Complete the query and return the Smart Panel to STANDBY by the query pressing 3 Maintenance The product may be cleaned with a soft damp cloth and then wiped dry Do not use abrasive solvent based or aerosol cleaners as this may damage and or discolour the product Do not allow water to enter or attempt to clean inside the unit 4 Batteries Do not allow the batteries to corrode or leak as this may cause permanent damage to the product Take care to insert the batteries with the correct polarity as shown inside the battery compartments Do not mix new and old batteries or different types of batteries Do not use rechargeable batteries At the end of their useful life the batteries should be disposed of via a suitable recycling centre Do not dispose of with your normal household waste DO NOT BURN 5 Alarm System Limitations Even the most advanced alarm systems cannot guarantee 100 protection against burglary or environmental problems All alarm systems are subject to possible compromise or failure to warn for a variety of reasons Please note that you may encounter problems with your system if e The sensors are not placed within hearing range of persons sleeping or re2. Model WS 101TX G2 RED SHIELD KEY FOB REMOTE CONTROL INSTALLATION AND OPERATING INSTRUCTIONS For use with Red Shield Wire free Home Protection System Please keep these instructions in a safe place for future reference Kit contents 1 x Key Fob Remote Control 1 x 12V alkaline battery included 1 x Instruction leaflet 1 Introduction The Red Shield Wire free Home Protection System Remote Control allows you to operate the systems Smart Panel remotely from inside or outside the property Using the control the system can be armed or disarmed and the siren can be activated instantly if required using the Panic function 2 Operation 2 1 Powering up the Key Fob Remote Control The Remote Control includes a 12V alkaline battery To activate unscrew and remove the back of the Remote Control and carefully remove the clear plastic insulation tab from the battery If the battery is dislodged replace it noting the correct polarity shown inside the battery compartment Replace the battery cover 2 2 Enrolling the Remote Control onto the Smart Panel Before they can operate the system new Remote Control devices need to be enrolled added to the system as follows 1234 You must be in STANDBY To make sure you are in STANDBY mode 4 digit PIN mode before enrollinga Enter the default PIN 1234 new Remote Control onto OR your new 4 digit PIN the Smart Panel Press The Smart Panel will display the image below whe
3. mote parts of the premises e The sensors are placed behind doors or other obstacles e Intruders gain access through unprotected points of entry where sensors are not located Intruders have the technical means of bypassing jamming or disconnecting all or part of the system e The power to the sensors is inadequate or disconnected e The sensors are not located in proper environmental temperature conditions i e too close to a heat source Note Inadequate maintenance is the most common cause of alarm failure therefore test your system at least once per week to be sure the sensors and sirens are working properly Although having an alarm system may make you eligible for reduced insurance premiums the system is no substitute for insurance
4. n you are in STANDBY mode 12345678 od One beep indicates that you entered a valid PIN three beeps indicate that an invalid operation was performed 1234 Enter the default PIN 1 The Smart Panel will display the below image 4 digit PIN 2 3 4 OR your new 4 digit PIN for setting Lee a See followed by to enrol it onto the Note It is recommended that the ID No is marked on the remote in system case it needs to be deleted at a later stage enren Press enrer to complete Confirm the enrolment and retum the Smart Panel to STANDBY by the enrolment pressing 2 3 Operating the Key Fob Remote Control ARM Pressing the ARM button on the remote will arm the system triggering the preset exit delay When triggered the Smart Panel s LED light will flash Red and indicate the triggered zone DISARM Pressing the DISARM button on the remote will disarm the system instantly and the system will return to Standby mode ALERT Pressing the ALERT button on the remote will put the system into Alert mode and a chime will sound if any of the sensors are triggered The Green light on the Smart Panel LED display will flash and indicate the triggered zone HOME Pressing the HOME button on the remote will set the system in Home mode which will operate the system in both Arm and Alert modes in different preset zones PANIC If the HOME and ALERT buttons are pressed together the systems alarm is immediately activated Pre
5. ss then LCD display flashes the ID no of the remote to be enrolled e g to enter the Remote when enrolling the first remote ID no 01 will flash Once the first D Control Enrol mode remote is enrolled the 02 will flash ready for a second remote to Then press any key on be enrolled One beep indicates that the remote was enrolled to the the new Remote Control Smart Panel successfully 2 4 Deleting a Remote Control from the Smart Panel Ifa Remote Control devices is damaged or lost it can be deleted from the system as follows 1234 You must be in STANDBY To make sure you are in STANDBY mode 4 digit PIN mode before deleting a Enter the default PIN 1234 Remote Control from the OR your new 4 digit PIN Smart Panel Press The Smart Panel will display the image below when you are in STANDBY mode 12345678 oo One beep indicates that you entered a valid PIN three beeps indicate that an invalid operation was performed 1234 4 digit PIN es Enter the default PIN 41234 OR your new 4 digit PIN for setting followed by Press gt lt then 6 to enter the Remote Control Deleting mode Then input the number of the Remote Control you wish to delete from the system Press Evren Evren to complete the deletion The Smart Panel will display the below image 12345678 LCD display flashes the total number of remote currently enrolled to the sys
6. tem e g If the Smart Panel has 3 remotes enrolled the LCD display will flash 03 Input the remote ID no e g 02 for the remote you wish to delete Inputting 00 will delete all remote controls LCD display will then flash the total number of remotes enrolled after deletion One beep indicates that the remote was successfully deleted from the Smart Panel Confirm the deletion and return the Smart Panel to STANDBY by pressing 2 5 Querying the ID Number of a Remote Control The ID number of a Remote Control device can be checked as follows 1234 4 digit PIN ENTER 1234 4 digit PIN ENTER You must be in STANDBY mode before querying the Remote Control ID number Enter the default PIN 1 2 3 4 OR your new 4 digit PIN for setting followed by Press gt then to go into Remote Querying mode and then press any key on the remote to check its ID To make sure you are in STANDBY mode Enter the default PIN 1234 OR your new 4 digit PIN Press The Smart Panel will display the image below when you are in STANDBY mode 12345678 ed One beep indicates that you entered a valid PIN three beeps indicate that an invalid operation was performed The Smart Panel will display the below image 12345678 After entering into Remote Querying mode the LCD display will flash the total number of remote controls currently enrolled to the system e
Download Pdf Manuals
Related Search