1.2 kW High Speed Hand Dryer Operating Instructions
Contents
1. Bare earth wires should be sleeved with a green and yellow sleeve b Connect the power cord to initiate stand by ready to operate status 7 Replace the filter access tray being careful to not over tighten the security screw 8 See separate sections for owner options on heater operation and air soeed adjustment fig 1 fig 2 fig 3 er AOR AAW LAN Cleaning and Maintenance Periodic cleaning of the unit is recommended to ensure optimum performance Wipe the cover with a damp cloth and mild cleaning solution Do not Soak Do not hose down Never use abrasives to clean the cover Caustic chemicals may damage unit finish No internal parts need any regular cleaning Red 110 120 Vac Orange 220 240 Vac Black Je1SOULION I OSnj OWs9Y YZI 4901 038H self YZ YOUMS ewsay YUM 1010W Transistor Power Switch VR1 FOR SENSOR transistor Clrcuit Board Module Power Switch 3 TELEEEEELEECEECECCECEECEECEECEELEELEECEELEEEEELLELELLEELEELEE TE ACTIVE TANDBY LED1 LED2 Air Speed Adjustment The dryer air soeed can be adjusted However when lowering the motor speed the drying time will increase also The ability of this function will be dependent on the needs of the owner The factory setting for dryer s motor speed is set at its highest speed See below for how to adjust the dryer speed 1 Use key supplied to2. unlock and withdraw the tray fig 1 2 Use flat blade screwdriver gently turn adjustment potentiometer fig 2 shaft clock wise CW to increase power to maximum shaft will hard stop DO NOT OVERTURN Turn tool gently CCW to reduce power as required shaft will hard stop DO NOT OVERTURN Note that at minimum power the unit may not start if low line Voltage condition exists 3 Insert the tray back and lock the security screw Reduce power Increase power fig 2 Heater Element Switch ON OFF The Dryer has been designed with a heater switch that can turn the heater ON OFF The heater switch doesn t affect the drying time In cold conditions it may be more comfortable if it is on when drying hands However it will save a third of the energy if itis off This function can be adjusted depending on the needs of the owner The factory setting for the heater will be on See below for how to turn the heater ON OFF 1 Use key supplied to unlock and withdraw the tray fig 1 2 Switch it to the right to turn ON Switch it to the left to turn OFF fig 2 3 Insert the tray back and lock the security screw Switch How to Chanae the Filter 1 Use key supplied to unlock and withdraw the tray fig 1 2 Change the filter fig 2 3 Insert the tray back and lock the security screw Recommended Period for Changing the filter Filter In general use normal light usage it s recommended to change
3. 1 2 KW High Speed Hand Dryer Model No B2013 220 240V 50Hz Operating Instructions Please read instructions in conjunction with the illustrations Please save these instructions Unit Size mm Inch 587 5 Specifications 322 185 TECHNICAL SPECIFICATIONS ITEM CATEGORY Operating Voltage Warm Air Speed Output Air Output Temperature Dryer Shall Deliver Cover Type Motor Type Motor Thermal Protection Heater Element Heater Thermal Protection Standby Power LED Color Drying Time Circuit Operation Sensor Range Sound Pressure Timing Protection Drip proof Isolation Net Weight Shipping Weight Unit Size PERFORMANCE DATA 220 240Vac 50 60 Hz 4 6 5A 1 0 1 2 kW 65 100 m s 140 224 mi hr Adjustable 45 C 113 F Ambient Temp 20 C 68 F 89 124 m h 55 76 CFM 3 0 mm thick molded ABS plastic 1HP 400 750W 11000 20000 R P M Adjustable Auto Resetting Thermostat turns unit off 240V at 95 C 221 F ON OFF Heating options 300 450W Adjustable Auto Resetting Thermostat turns unit off at 85 C 185 F Thermal cut off at 142 C 288 F 1W Standby color red Active color blue 10 15 seconds Infrared Automatic self adjusting standard 12 cm 1 cm MIN 65 dB A to 78 dB A MAX 1m 60 seconds auto shut off IP23 6 CLASS 1 10 8 kg 12 8 kg 322 mm W x 588 mm H x 185 mm D Recommended Mounting Heights 4 B From Top of Hand From Datu
4. Ensure that the mains supply voltage frequency and phase complies with the hand dryers rating label e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that they do not play with the appliance Installation Steps 1 Tape the installation template to the appropriate location on the mounting surface Drill eight 8 holes at marked locations fig 1 2 Remove template and Insert eight 8 plastic anchors supplied into drilled holes fig 2 3 Insert eight 8 screws supplied to fix backplate into top plastic anchors fig 3 4 Hang the dryer on the base plate fig 4 5 Use key supplied to unlock and withdraw the tray Screws supplied through the holes at backplate bottom Insert the tray back and lock the security screw fig 5 6 a Connect hard wired power provided at KO location to terminal block behind cover panel RH bottom behind filter tray Turn on circuit breaker to initiate stand by ready to operate status Connections A Connect the live wire coloured Brown to the terminal block marked L B Connect the neutral wire coloured Blue to the terminal block marked N C Connect the earth wire to the terminal block marked or
5. ended to clean the drain tank every 3 months water will come through the overflow hole if the drain tank is full A drainpipe not included can be added if necessary The specifications of the drainpipe is I D 6mm O D 10mm fig 1 fig 1 For replacement filters and spares please contact your supplier for details Dad This product should not be disposed of with household waste Please recycle where facilities exist Check with your local authority for recycling m VICE Supplied by FHD Online 0312
6. m Point From Bottom of Dryer Drying Chamber Men 1150 710 622 Women 1080 640 552 Children 4 7 years 780 340 252 Children 8 10 years 880 440 352 Children 11 13 years 965 525 437 Children 14 16 years 1080 640 552 Handicaped 900 460 372 Top of Hand Drying Chamber 4 ocm _y Datum Point F Bottom of t TE Dryer B D F lt Power Cord Reach Range gt l adi Floor Cable entry The dryer is supplied with a power cord The power cord i e Os Datum point entry position is in the rear right side bottom of dryer The length of the power cord is 1 5M Cable entry Position Detail A Unit Rear General Safety Information A WARNING This product is intended A WARNING Disconnect power at the for installation by a qualified service person service breaker before installing or servicing Use AWG NO 16 solid conductor for wiring not for household use may case burns 1 2mm for 220 240V A DANGER Failure to properly earth A WARNING All units must be supplied unit could result in severe electrical shock with a 3 wire service The earth wire must and or death be connected to the dryer s backplate Important Read all these instructions before commencing the installation e All wiring of this hand dryer should be in accordance with the current IEE regulations or the appropriate standards in your country e This hand dryer MUST be installed by a suitably qualified person e
7. the filter six 6 months In dusty dirty places heavy usage it s recommended to change it every three 3 months Filter Assembly Information ern Filter AANA AN ANAL carbon Filter Antibacterial HEPA Filter Antibacterial Carbon Filter Filter Filter Instructions for use maintenance and changing the absorbent ceramic The absorbent ceramic can absorb 70g of water and has the capacity to take a full load approximately 280 times per day The ceramic also can evaporate water During normal use water will be evaporated continuously and maintain the function of absorbing Maintenance simply requires clearing its surface Normally its lifetime will be the same as the machine Improper use or maintenance could result in breakage see below for replacement instructions 1 Use the key to loosen the security screw and remove the tray fig 1 2 Use the key to loosen the security screw of the base plate and remove the machine fig 2 3 Use a screwdriver to loosen the screw 2 pcs on the ceramic and replace it with a new one fig 3 4 Put the machine back and secure the security screw to the base plate 5 Put the tray back and lock up the security screw Generally the remaining water following usage will evaporate in the absorbent ceramic During high traffic times leftover water will flow to the drain tank automatically The capacity of the drain tray is 240 cc It s recomm
Download Pdf Manuals
Related Search