Operating instructions
Contents
1. 10 8 Removing the bath lift from the bath tub 10 9 Cleaning 11 Warranties maintenance amp servicing 10 Maintenance and servicing 11 l EMWaFrANE T2 12 Symbols RAS M C S EEE vee 12 Technical data 13 Technical data 4444 44 13 Troubleshooting 14 Troubleshooting 15 Parts list 15 Accessories 18 16 PASSE 4 eeka 20 Diagrams for operation and explanation of use are on the fold out diagram sheet attached to the rear of this booklet 1 Unpacking the bath lift Open the packaging and ensure the bath lift is not damaged and that all parts are included If it has been damaged in transit or parts are missing contact your supplier immediately Inside the box you will find e A bath lift complete with two side flaps and hand control attached see fig 1 A battery see fig 2 e A battery charger with charging cradle attached see fig 2 If your bath lift is supplied with optional soft covers fit them at this stage see cover fitting instructions Before installing or using the bath lift for the first time ensure you charge the battery see section 2 Charging the battery below 2 Charging the battery Before first operation of your bath lift or after long periods of non use typically 7 10 days fully charge the battery as follows A flat battery will take up to 2 hours to charge i Slide the battery into2. 4 Installing the bath lift i Pick up the bath lift holding it as close as possible to your body ii Place the suction feet on the flat bottom of the bath tub and as far back as possible at the opposite end to the taps faucets If there are any overhead obstructions at the back of the bath tub that cannot be removed and are likely to interfere with the uoward movement of the bath lift move the bath lift further forward in the bath tub until clear of the obstacle iii Now press firmly down on the seat ensuring all four suction feet are attached to the bath tub surface NOTE The suction feet may not stick to very curved or contoured surfaces iv Unfold the two side flaps so they rest against the sides of the bath tub Side flaps ease transfer on and off the bath lift and also prevent finger entrapment If side flap protectors are required and have been fitted to integral bath tub handles ensure the two side flaps are resting substantially on them If the side flaps are still likely to catch under handles move the side flap protectors as far as possible along the handles until the side flaps are over them see fig 4 If this still does not improve the flaps position on the side flap protectors move the bath lift slightly forward in the bath tub Alternatively a side flap protector extension kit is available see section 15 Accessories v Fill the bath tub with water to the required level ensuring the actuator casing see
3. Symbols To comply with international standards for medical equipment the following symbols are found on the bath lift s labels Symbol Explanation mn Only direct current from a small battery is used to power your bath lift There is NO Connection to mains electricity when in use so there is no risk of electric shock A The bath lift is categorised as type B medical equipment and meets international standards for electrical safety IP66 The bath lift is sealed to the international standards against the effects of water spray IP67 The battery is sealed to the international standards against the effects of immersion in water to a depth of 1 metre 3 28 ft IP68 The hand control is protected against long periods of immersion in water under pressure This symbol is found on the hand control and means the light represents the battery status PLEASE READ THE INSTRUCTIONS BEFORE INSTALLATION OR USE Do not bin dispose 7 _ A A X SN Serial number Re order number Symbol Explanation Maximum load lifting capacity person AN Caution Surface hot to touch 13 Technical data The bath lift seat and base is made of glass filled polypropylene The base frame tubes are made of aluminium The hand control and battery are made of ABS The hand control button cover and suction feet are made of thermoplastic elastomer The bath lift is in the o
4. actuator behind the backrest to be placed under a constant flow of water e g running tap faucet and ensure it is not totally submerged in water 7 When the bath lift is not in use i If you wish to clean the bath lift whilst it is in the bath tub see section 9 Cleaning we recommend doing so when it is at its highest position in the bath tub This allows access for cleaning both the bath tub and the underside of the bath lift ii If the bath lift is stored in the bath tub ALWAYS ensure the seat is lowered to the bottom of the bath tub NOTE If the RED light has appeared on the hand control preventing you from lowering the bath lift to the bottom of the bath tub for storage recharge the battery immediately see section 2 Charging the battery and lower the bath lift to the bottom of the bath tub as soon as possible thereafter iii Disconnect the battery and place on charge ready for your next bath see section 2 Charging the battery Note If not charging after each bath ensure you leave the battery connected to the hand control Disconnect from the hand control only if the bath lift is being removed from the bath tub 8 Removing the bath lift from the bath tub i Ensure the bath lift is in its lowest position at the bottom of the bath tub li Remove the battery from the hand control iii Place the hand control on the seat and fold the side flaps in iv Hold the top of the backrest and as you pull the r
5. fig 5 is not submerged in water Check that the water temperature is not too hot before using the bath lift vi The battery can now be connected to the hand control on your bath lift see section 5 Connecting the hand control 5 Connecting the hand control NOTE If the battery has not been used before or has not been used for a long period typically 7 10 days ensure you place it on charge before using the bath lift i Slide the fully charged battery into the tracks on the hand control see fig 6 until it clicks into place li Always check the battery status indicator on the hand control before using the bath lift see fig 7 Press the UP button and observe the following guidelines If GREEN light proceed with your bath provided the battery has been charged within the last 7 10 days If FLASHING GREEN light proceed with your bath provided the battery has been charged within the last 7 10 days Then charge immediately afterwards see section 2 Charging the battery e If RED light do NOT use the bath lift Charge IMMEDIATELY see section 2 Charging the battery e fin any doubt recharge the battery before use see section 2 Charging the battery NOTE The battery is for use solely with Mountway bath lifts and cannot be used to operate any other product 6 Using the bath lift NOTE Ensure all four suction feet are attached to the bath tub surface before each use i T
6. of charging before handling the box e Ensure that no metal objects touch the contacts on the battery as this will damage the battery e Use only the Mountway charger supplied to charge the battery and for no other purpose 3 Preparing the bath tub for installation i Remove any non slip mats from the bath tub ii Ensure the bottom of the bath tub is clean and smooth with no oil or bath tub cleaner residues that will prevent the suction feet from sticking iii The suction feet may not be suitable in baths tubs that have been re enamelled or that have rippled or textured surfaces iv It is essential that the side flaps see fig 1 do not catch under any obstructions such as integral bath tub handles handrails soap dishes and taps faucets when rising If your bath tub has integral handles and the side flaps are likely to catch optional side flap protectors are available see section 15 Accessories These hook over integral bath tub handles see fig 3 and help guide the side flaps smoothly over the handles v Ensure there are no overhead obstructions at the rear of the bath tub where the bath lift will be positioned e g wall mounted shelves cupboards or shower fixtures as they may interfere with the upward movement of the seat Where possible remove such obstructions Alternatively the bath lift must be placed further forward in the bath tub to avoid the obstruction see section 4 Installing the bath lift
7. able Check for light indicator connected to power on charger box socket outlet e Battery is not e Insert battery correctly into both tracks Section 2 connected correctly on charging cradle and slide all the way to charging cradle to the end until it clicks e Battery has Ensure battery is disconnected from Section 2 discharged before charging cradle when mains socket USE is switched off or when charger is removed from mains socket outlet e Charge battery after long periods of non use typically 7 10 days e Interruption to e Check for charger indicator lights at n a mains power supply alternative power socket outlet or faulty mains e Check if other electrical appliances socket outlet are working e Charger fault e Contact supplier or authorised service n a repair centre e Battery fault e Contact supplier or authorised service n a repair centre Charger is plugged Battery is not e Insert battery correctly into both tracks Section 2 into power socket connected correctly on charging cradle and slide all the way outlet but charger to charging cradle tothe end until it clicks indicator lights do Charger fault e Contact supplier or authorised service n a not appear repair centre 16 Symptom Possible Cause Solution Section No lights appear Battery is not e Insert battery correctly into both tracks Section 5 on hand control connecte
8. ach the hand control and battery to the edge of the bath tub or to a tiled wall If the hand control and battery fall into the water there is NO danger as both are waterproof Ensure you wipe the battery dry before charging ix When you have finished bathing retrieve the battery and hand control from where you have stored it by pulling the tags on the suction cups Press the UP button to raise the bath lift When the button is released the bath lift will stop and remain at that position until the button is pressed again x Once the side flaps are level with the top of the bath tub remove your finger from the UP button and move sideways onto the side flap ensuring once again that no part of the body can become trapped as you do so Turn whilst lifting each leg out of the bath tub Drain the bath tub XI xii NOTE e If the RED light appears on the hand control whilst lowering the bath lift will not go down any further If this happens press the UP button and the bath lift will raise you to the top of the bath tub Charge the battery immediately e In the event of an emergency sliding the battery out of the hand control can instantly terminate all bath lift movement e When the bath lift reaches its maximum limit of travel up or down there will be a short delay before it will operate again e The bath lift is not designed for continuous operation Allow at least 15 minutes between baths e Do NOT allow the
9. annot be moved further along an integral bath tub handle to enable the side flap to rest substantially over it this kit enables an additional side flap protector to be attached beyond the end of the bath tub handle This provides a substantial surface area for the side flap to glide smoothly over the bath tub handle Use several kits to attach as many side flap protectors as required beyond the bath tub handle Accessory Part No Extended suction feet set BB3100 Raises the bath lift by 25mm linch to enable the seat and side flap to reach level with the height of deep baths tubs 19 16 Parts List Item No Description Part no 11 Actuator BB3004 12 Hand Control NiMH AB105 13 Complete Base Frame No BB3007 Suction Feet 14 Base Frame Tube End Cap BB3009 15 Actuator Snap Pin AB003 Suction Foot Removal Tool BB3901 not shown Suction Feet Set of 4 with BB35045 Removal Tool not shown Item No Description Part no 1 Left Side Flap BB3002L 2 Seat BB3001 3 Right Side Flap BB3002R 4 Side Flap Hinge with Screw A167 5 Smart Charger NiMH UK CU 3000 Smart Charger NiMH US CU 3001 6 Battery A230 7 Suction Foot BB3504 8 Actuator Locking Pin BB3107 9 Actuator Clamp BB3003 10 M6x12mm 0 47in Long 11539 Socket Button Screw x4 Mountway Limited reserve the right to alter specifications to products
10. d correctly on hand control and slide all the way to when buttons are to hand control the end until it clicks pressed e Faulty electronics in Contact supplier or authorised service n a hand control repair centre Suction feet will e Front suction feet Do not use bath lift Section 3 not stick to the are located over bath tub surface rippled surfaces e Suction feet are e Position suction feet on flatter surface Section 4 located on very of bath tub curved surfaces e Bath tub surface e Clean bath tub surface and underneath Section 3 is dirty dusty or suction feet before installing bath lift enamel is worn e Suction feet are old Contact supplier or authorised service n a or damaged repair centre for replacements Bath lift tips e Bath lift not stored Always lower bath lift to bottom of Section 7 backwards in properly after bath bath tub after use Check suction feet highest position stick to bath tub before each use e Front suction feet DO NOT USE bath lift Rippled surfaces Section 3 are located over prevent secure suction rippled bath tub Surface e Suction feet are e Position suction feet on flatter surface of Section 4 located on very bath tub DO NOT USE if front suction curved surfaces feet do not stick to contoured bath tub surface e Suction feet not e Clean bath tub surface and underneath Section 3 sticking to dirty suction feet before pressing all 4 suction dusty bath tub feet firmly on
11. elease tags on each of the rear suction feet tilt the bath lift forward see fig 8 v Continue to release the tags on the front suction feet and lift the complete bath lift out of the bath tub Stand the bath lift upright then wrap the hand control cable clockwise around both the lt seat and tubes ensuring the cable coil is positioned underneath the actuator casing Now loop the remainder of the cable around one of the tubes see fig 9 vii Store the bath lift upright or lay it on its side NOTE e When lifting the bath lift always lift close to your body To avoid accidental damage to the hand control whilst carrying or storing ensure it is prevented from dangling freely 10 9 Cleaning Clean the bath lift as frequently as you clean your bath tub using non abrasive cleaners If used communally we recommend disinfecting the bath lift after each use SOLVENT based cleaners such as white spirit should NOT be used i To disinfect the bath lift use a soft brush or cloth and wipe down with a sterilising solution or anti bacterial cleaner Rinse the product with clean water then wipe and dry using a clean cloth li Bath medicinal oils and other solutions are easily removed with washing up liquid Do not allow oils or other additives to build up They should be removed frequently otherwise over the course of time they may lead to degradation of the suction feet and or discolouration of the bath lift The bath l
12. fficial category of internally powered equipment and is not suitable for use in the presence of flammable anaesthetic mixture with air or nitrous oxide The equipment is tested in accordance with BS EN 10535 2006 BS EN 60601 1 2006 The European Council Directive 93 42 EEC relating to Medical Devices The bath lift complies with the WEEE directive DISPOSAL The plastic metal parts packaging materials and suction feet are recyclable but the Nickel Metal Hydride NiMH battery should be disposed of only by returning it to your supplier the manufacturer or an authorised disposal point 175mm 689in 330mm 12 99in 175mMmMm 6 89in 510mm 20 08in m 340mm 13 39in Overall seat width 350mm 13 8in 13 Uleg CC UUOSS Bath Lift Lifting capacity person 127kg 20 stone 2801bs Net weight excluding battery 6 5kg 14 33lbs Seat height UP 460mm 18 11in Seat height DOWN loaded 70mm 2 76in Power input 14 4V dc nominal 7A max Duty cycle Not more than one bath per 15 minutes Degree of protection IP66 Hand Control Battery 14 Input 14 4V dc nominal 1 0A Output 14 4V dc nominal 7A max Degree of protection IP68 Battery IP67 Battery Charger Input 100 240V ac 50 60Hz 1 0A Output 14 4V dc nominal 1 0A Operating and charging Shipping and
13. ift can be cleaned in an automated washing machine to a maximum temperature of 73 C 163 F for 3 minutes however the battery MUST be removed and washed by hand The battery must not be subjected to high temperature cleaning iv Do not clean or rinse the actuator under a constant flow of water e g running tap faucet or totally submerge it in water v If your bath lift is fitted with soft covers ensure you remove them on a regular basis to clean the bath lift surfaces It is also advisable to clean the bath tub surface under the suction feet from time to time Cleaning agents should be used in accordance with their manufacturer s guidelines NOTE If the actuator is detached from the bath lift for cleaning ensure the battery is always disconnected from the hand control 10 Maintenance and servicing Repairs and servicing must be entrusted to a Mountway authorised dealer or engineer The bath lift should be inspected annually by a Mountway authorised dealer or engineer who will check that there are no loose fittings or any other evidence of mechanical damage Intended life bath lift The durability of the bath lift has been tested in accordance with BS EN 10535 2006 Hoists for the transfer of disabled persons requirements and test methods If serviced and used in accordance with the operating instructions the bath lift and all parts excluding battery will achieve 11 000 lifting cycles or 5 years use whiche
14. neptune splash liberty bath lift bath lift Operating instructions mountway bringing independence to life Please ensure both yourself and any helpers read these operating instructions carefully and in full before using your bath lift These operating instructions should be retained for future reference This bath lift is designed and manufactured to assist individuals in getting in and out of the bath tub It should not be used for any other purpose Do not use it in combination with other lifting or moving devices If you are unable to get out of the bath tub unaided do not bathe without someone on call to help in an emergency Quick start guide This guide should be read in conjunction with your bath lift s full operating instructions which start on page 4 e When the light is constant red it is charging Charge the battery by sliding it into the tracks on the charging cradle fig 1 and plugging it into the mains When the light is constant green it is ready to use 2 a el eri the bath tub by removing Non slip mats oil and cleaner residues e Obstructions such as handles or fit side flap protectors handrails and soap dishes Overhead obstructions at the rear and over the bath tub such as cupboards shelves 3 Install the bath lift by e Placing it with the suction feet on the flat bottom of the bath tub and at the opposite end to the taps faucets e Checking for any obstr
15. o raise the bath lift press the UP button on the hand control see fig 7 If the side flaps are caught on any obstruction immediately lower the bath lift by pressing the DOWN button on the hand control Pull each side flap free from the obstruction then resume the lifting operation li As the bath lift reaches the top of the bath tub the side flap on the side you will be getting on will fold out to form a transfer platform iii When the bath lift s seat and side flap are level with and supported by the top of the bath tub release your finger from the UP button and the bath lift will stop iv Sit on the side flap and move onto the seat ensuring no part of your body can become trapped as you do so e g underneath the side flaps You may find it easier to transfer if you wet the seat and the side flaps first Turn as you lift each leg over the side of the bath tub then sit back in the seat and make yourself comfortable 8 v Before lowering the bath lift extend your feet out in front of you and keep hands above the seat to avoid any risk of entrapment vi To lower yourself to the bottom of the bath tub press the DOWN button on the hand control see fig 7 When the button is released the bath lift will stop and remain at that position until the button is pressed again vii When you have reached the bottom of the bath tub the bath lift will automatically stop viii Whilst bathing you may use the suction cups on the battery to att
16. or e Charge battery before use if bath lift has Section bath lift does not long period typically not been used for long periods typically 5 amp move 7 10 days 7 10 days Section 7 e Do NOT start bath with RED light on hand control Charge immediately e Ensure battery is placed on charge as soon as you finish your bath if FLASHING GREEN light appears on hand control e When bath lift is not in use leave battery connected to hand control Disconnect only for charging or when moving bath lift e It is recommended the battery be charged after each bath wherever possible e Battery fault e Contact supplier or authorised service n a repair centre 15 Symptom Possible Cause Solution Section Bath lift e Battery is not fully Charge battery Section 2 only moves charged intermittently e Excessive user load Do not use bath lift if you weigh over Section 13 20st 127kg 280lbs e Bath lift has e Lower bath lift pull flaps free from Section encountered obstruction then resume lifting 6 amp obstruction during operation Section lifting e g integral Contact your supplier for optional side 15 bath tub handles flap protectors and fit to any integral soap dish bath tub handles Battery does e Power to charger e Ensure charger plug is connected to Section 2 not appear to be is not switched on power socket outlet and switch on charged or charger is not if applic
17. or packaging at any time 20 Diagram sheet Figures 1 Hand control Bath Lift Side flap Suction feet 2 QO Battery O Charger O Charging cradle Light indicator Tracks 3 Integral bath tub handle O Side flap protector 4 Integral bath tub handle O Side flap protector Side flap 5 Side flap O Actuator casing Hand control 6 O Battery O Tracks Hand control 7 Hand control O Battery status indicator up Down 8 Top of backrest O Suction release tag 9 Cable coil O Actuator casing Gs Firststreet tel 1 804 451 2310 fax 1 804 524 9889 email mail mountway co uk www firststreetonline com Mountway Limited 2011 REF ML3BB1 02 04 11 Tafarnaubach Ind Est Tredegar NP22 3AA UK tel 44 0 1495 723300 fax 44 0 1495 723360 freephone 0800 014 1852 e mail mail mountway co uk www mountway com Approved code ISO 9001 CERTIFIED ORGANISATION 7 i v y yy URS bt core TS United Registrar of Systems Cert No 91430 INVESTOR IN PEOPLE
18. storage Temperatures Weight packaged 9kg 19 84lbs Max 40 C 104 F Shipping volume 0 12m 4 24ft Min PENSE Temperatures Max 40 C 104 F Min 10 C 14 F Humidity Max 90 RH Min 10 RH Pressure Max 125kPa 18 4psi Min 73kPa 10 7psi This product is suitable for transport in pressurised aircraft holds 14 Troubleshooting Symptom Possible Cause Solution Section Bath lift does not Battery is flat e Charge battery Section 2 move No sound Battery is not e Insert battery correctly into both tracks Section 5 from the motor connected to hand on hand control cradle and slide all the control way to the end until it clicks Not pressing correct Press arrowhead on either UP or DOWN Section 5 area on hand buttons Continue to press control buttons e Faulty electronics in Contact supplier or authorised service n a hand control repair centre e Battery fault e Contact supplier or authorised service n a repair centre Replace battery e Actuator fault e Contact supplier or authorised service n a repair centre Red light on hand Battery is flat or Charge battery immediately Section 2 control is on and has not been fully bath lift only charged and Stop moves up Descent has been activated to prevent the bath lift lowering Red light on hand Battery is flat and has Charge battery immediately Section 2 control is on but not been charged f
19. the tracks on the charging cradle until it clicks into place see fig 2 ii Plug the charger into the mains socket outlet outside the bathroom and switch on the electricity supply if applicable iii The light indicator on the charger box will initially flash in a quick sequence of red green red green before a constant red light appears to indicate charging is in progress see fig 2 iv When the battery has been fully charged the red light on the charger box turns to a constant green light which indicates the battery is ready for use We recommend charging the battery after each bath wherever possible and leaving it on charge until your next bath The battery cannot be overcharged v When you are ready to use your fully charged battery see paragraph iv switch off the mains socket or remove the charger from the mains socket outlet then ensure you disconnect the battery from the charging cradle This prevents the battery discharging and will reset the charger ready for its next use NOTE e Do not charge in the bathroom or any humid area Always charge in a dry area ensuring your hands are dry first Do not cover the battery or charger whilst charging e Always charge on a hard surface e During charging the temperature of the charger box may exceed 40 C but will gradually decrease once the constant green light on the box appears Users with sensitive damaged skin should take care and allow approximately 3 hours from start
20. to bath tub Surface or worn enamel e Old or damaged e Contact supplier or authorised service n a suction feet will not stick to bath tub surface repair centre for replacements 17 15 Accessories The bath lift can be supplied with a range of optional accessories Accessory Part No Soft cover set back and seat BB3103 Provides even greater comfort Accessory Part No Side flap protector AB283 Side flap protectors are available should your bath lift not sit far back enough in the bath tub to avoid integral handles Supplied individually the protector hooks onto a bath tub handle to prevent side flap from catching when raising the bath lift Internal hook section is uniquely coated with slip resistant rubber to limit movement along handle Accessory Part No Side flap protector extension kit AB284 Comprises 1 side flap protector and 2 clips By attaching one or more side flap protectors together a wider side flap protector can be formed over an integral bath tub handle This limits the possibility of movement along the handle or incorrect positioning Use several kits to attach as many side flap protectors as required to fit the handle length 18 Accessory Part No Side flap protector extension kit AB287 non hooking Comprises 1 non hooking side flap protector and 2 clips Where a standard side flap protector c
21. uctions likely to interfere with the bath lifts movement move the bath lift forward if there are fixed overhead obstacles Pressing firmly on the seat to secure the suction feet to the bath tub Then e Unfold the two side flaps to rest against the sides of the bath tub e Run water to any level under the actuator casing fig 2 4 Use the bath lift by e Sliding the charged battery fully into the tracks on the hand control fig 3 Pressing the UP button 2 Tracks Charging cradle Charger Battery Light indicator Figure 1 Suction feet Figure 2 Only continue if the light on the hand control is constant or flashing green and if the battery has been charged within the last 7 10 days When the seat reaches the top of the bath tub e Release your finger from the UP button e Sit on the side flap and rotate onto the seat e Extend your feet out in front of you and keep your hands above the seat Press the DOWN button on the hand control e Attach the hand control and battery to the edge of the bath tub or to a tiled wall For convenience during bathing you may raise or lower the seat to any desired height by pressing the UP or DOWN button and releasing it to stop When you have finished bathing Retrieve the battery and hand control e Press the UP button until the side flaps are level with the top of the bath tub e Release the UP button and move onto the side flap e T
22. urn whilst lifting each leg out of the bath tub e Drain the bath tub 5 When you are not using the bath lift e Disconnect the battery and place on charge Store the lift at the bottom of the bath tub To remove the lift from the bath tub place it in its lowest position and e Disconnect the battery from the hand control Place the hand control on the seat e Fold in the side flaps e While holding the top of the backrest pull the suction release tags on the rear suction feet then tilt the bath lift forward fig 4 e Release the tags on the front suction feet and lift the bath lift out of the bath tub Wrap the hand control cable clockwise around the seat positioning the cable coil under the actuator casing Loop the remainder of the cable around one of the tubes fig 5 e Store the bath lift upright or on its side Tracks Battery Top of backrest Suction release tag Hand control Figure 3 Figure 4 Cable coil Actuator casing Figure 5 Operating instructions Contents Unpacking the bath lift 1 Unpacking the bath lift 5 Before you start 2 Charging the battery 5 3 Preparing the bath tub OrInstall tiOn ss homme 6 4 Installing the bath lift 7 Using the bath lift 5 Connecting the hand control 8 6 Using the bath lift 8 Removing and storing the bath lift 7 When the bath lift is not in use
23. ver is the soonest Intended life battery It is essential that the operating instructions with regards to battery use and charging is adhered to The battery life expectancy is 500 charge cycles or 1 year s use whichever is the soonest We recommend the battery be replaced accordingly in order to obtain the best performance from your bath lift 11 11 Warranty This product is sold with the benefit that in the event of any defect of manufacture or material appearing within 1 year of the date of receipt of the product the defect will be rectified free of charge provided that i Reasonable evidence is provided e g purchase invoice or delivery note that the product was purchased not more than 1 year prior to the date of claim and li The defect is not attributable to accidental damage either in transit or otherwise fair wear and tear willful damage misuse or unauthorised repair The battery is also guaranteed for 1 year to power when fully charged one bathing cycle at full load 20 stone 127kg 280lbs Consumers statutory rights are not affected The bathing cycle For one bath it is assumed that the bath lift will be raised from the bottom to the height of the bath tub and then lowered into the water supporting a person of up to 20 stone 127kg 280 lbs After bathing the bath lift will raise the person to the height of the bath tub then the seat will be lowered to the bottom of the bath tub for storage 12
Download Pdf Manuals
Related Search