A-K81 CODELOCK Installation & Operating Instructions
Contents
1. Open S Gnd Page 3 FOREMATIC p Do not use in high humidity Do not drop or apply physical shocks Do not expose units to acid oxides ammonia or any other harmful substances Wipe down with a soft damp cloth Do not spray or immerse units in liquids or use a hose pipe or pressure cleaner near the panel Lime released from new mortar is alkaline and corrosive to entry panel components The inside of the entry panel should be checked from time to time for moisture and ingress of road dirt Check that the case seals are functioning Insects may find a way into the entry panel to nest Clear them with a vacuum cleaner Seal the cable entry points with petroleum jelly and spray lightly with WD40 Ensure the power is off before working inside the panel There are no electrical settings or fuses inside Codes and relay on times may need to be changed Refer to programming section Damaged units may be returned to the manufacturer to assess for repair Most often it is found more expedient to replace damaged units Waste electrical products should not be disposed of with normal household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice This equipment is warranted to be free from defects in material and workmanship for a period of 12 months from the date of purchase as indicated on the proof of purchase and or by serial number on the product C Def2. Doc QP AK81 Codelock V1 2 English A K81 CODELOCK Installation amp Operating Instructions 1 User guide 1 1 Description Page 1 1 2 Technical characteristics Page 1 1 3 Operating instructions Page 1 2 Installation 2 1 Installation Page 2 2 2 Programming Page 2 2 3 Wiring diagram Page 3 2 4 Maintenance amp warranty Page 4 Construction Twelve bright nickel plated keys are set on a bright nickel AE with an signi ia qeinhved The keys T User codes 1 code 4 to 8 digits back lit through the key legend by blue LEDs The PVC Relay time 01 99 secs or latching 00 chassis box has a cable access through a grommetted hole in the rear Two screws release the panel from Dimensions 90w x150h x 20d below Electrical connections are on two screw terminal Weight 300g blocks on the PCB Supply 12 14V ac dc Electrical Power Standby 0 23W The codelock has a relay output with isolated contacts nlockin 75W Power terminals B and Gnd accept AC or DC power 19 ZE There is an exit button input A buzzer gives audible Material Bright nickel plated alloy feedback when keys are pressed A green LED lights Protection IP54 with rainhood as the relay operates A red LED lights in programme mode Illumination Backlit with blue LED Relay output NO volt free contact 2A res Programming R A master code must be entered to make programme Temp range 10C 50 C changes Three para
3. model A K81 has been manufactured in accordance with the following standards or normative documents EN61000 6 3 2007 EN61000 3 2 20064 A1 2009 A2 2009 EN61000 3 3 2008 EN61000 6 1 2007 EN60065 2002 A1 2006 A11 2008 In accordance with the following directives 2006 95 EC The Low Voltage Directive 2004 108 ECG The EMC Directive April 201 1 FOREMATIC 9 Vanalloys Estate Stoke Row Henley OXON RG9 SQW United Kingdom CE Forematic 9 Vanalloys Estate Stoke Row Henley RG9 5QW www forematic com Page 4
4. ble below User code 1234 5678 is pre programmed for test purposes User code Mastercode Relay time 3 Software reset The codelock can be reset from the keypad Enter mastercode 11111111 enter TE red LED lights and codelock beeps OK Press 50 codelock beeps OK All the user code relay time and mastercode are returned to their default 4 Set the user code to eg 87654 Enter mastercode 11111111 x enter Me red LED lights and codelock beeps OK Press 51 codelock beeps OK Press 87654 codelock beeps OK The new user code is now 87654 If an invalid code is attempted the codelock beeps error which is 4 beeps 5 Setting the relay time eg set to 3 secs Enter mastercode 11111111 enter eee red LED lights and codelock beeps OK Press 52 codelock beeps OK Press 03 codelock beeps OK The new relay on time is now 3 seconds If an invalid time period is attempted the codelock beeps error which is 4 beeps 6 Changing the master code to 1313 1313 Enter old mastercode 1111 1111 ok enter f d LED lights and codelock beeps OK Press 56 codelock beeps OK Press 1313 1313 codelock beeps OK The mastercode is now 1313 1313 If an invalid code is attempted the codelock beeps 4 times for error Page 2 FOREMATIC EXIT BUTTON EXIT BUTTON Suppression diode LOCKING 12V MAGNET 50 60Hz 50 60Hz EXIT BUTTON 12W or 24V ac or dec
5. ective units returned by the purchaser at his own expense during this period will be at the vendors discretion either repaired and returned or replaced with an equivalent piece of refurbished and tested equipment The repaired equipment or replacement is then warranted for the balance of the initial warranty period or for thirty 30 days whichever is longer The repair or replacement will be without charge provided that the equipment has not been subjected to electrical or physical misuse or to unauthorised repair or modification The foregoing warranty is in lieu of all other warranties express or implied including but not limited to merchantability or fitness for a particular purpose The purchaser s exclusive remedy with respect to any and all losses or damages resulting from any cause whatsoever shall be repair or replacement as specified above Distributor shall in no event be liable for any consequential or incidental damages however occasioned whether by negligence or otherwise No suit or action shall be brought against manufacturer more than one year after the accrual of the cause of action thereof No agent employee or representative of the distributor nor any other person is authorised to modify this warranty in any respect This warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction Declaration of Conformity We hereby declare that the codelock
6. meters can be set via the keypad the user code the relay ON time and the master code There is a recovery procedure that resets all the codes back to the factory settings in case a mastercode is lost Page 1 FOREMATIC 1 Install the low voltage cable through the wall setting the codelock about 1 5m above ground 2 Remove the rain hood then take the panel off the back box Access is by two screws from underneath 3 Place the rain hood and plastic back box against the wall with the wires passing through the grometted hole in the rear of the back box Drill the wall through the three mounting holes and fix 4 Cut the wires to length and connect as the wiring diagram Allow at least 3 inches of cable to allow the panel to be removed 5 Fix the two front panel screws from beneath 6 Connect the power then try the test user code 1234 5678 The green LED on the panel should light for 5 seconds as the relay switches on FOREMATIC 1 Master code The mastercode is the key to programming The codelock leaves the factory with the mastercode set to 1111 1111 You are advised to change it to a unique number at the first opportunity 2 Codes This codelock has one user code from 4 to 8 digits long Before starting programming you will need to have a user code in mind and preferably a new mastercode Avoid dates of birth car registrations and local phone numbers Choose a number then write it in the ta
Download Pdf Manuals
Related Search