Operating instructions RPG 4.5, RPG 8.6
Contents
1. 4 0 D 15 RPG 8 6 114 3 4 5 D 15 RPG 8 6 141 3 5 6 C 11 RPG 8 6 152 4 6 0 C 11 RPG 8 6 168 3 6 6 C 11 RPG 8 6 219 1 8 6 B 7 The table is based on a cutting speed of approx 3 m min with high alloy steel Note The higher the cutting speed the higher the attrition of the multifunctional tool 18 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc G orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 6 Operation Attention Switching the RPG on Note WARNING Note Note G orbitalum tools gmbh 6 5 Switching the RPG on Tool damage A tube which has not been sawn off square may damage the tool if the distance between the cutting edge and the tube end is too short gt Before switching the RPG on make sure that there is sufficient distance between the cutting edge and the tube end 1 Connect the RPG for connection requirements see the chapter 5 3 p 11 2 Press the ON OFF switch The RPG starts up If the tool vibrate after starting up the cutting speed is too high gt Reduce the number of revolutions see the chapter 6 4 1 p 17 6 6 Processing the tube Hot and sharp edged chips Danger of injury to eyes and hands Always work wearing safety goggles gt Only remove chips wearing safety gloves When cutting do not exceed a chip thickness of 0 05 mm By exceeding the load limiting device adapter code 790 038 126 can be cut see problem solving chapter 8 1 p 22. RPG 4 5 RPG 8 6 Clamping the tube 1 Open the clamping shells by shifting the clamping lever 2 Insert the tube allowing it to have distance to the tool 3 Clamp the tube in by means of the clamping lever Possibilities of adjustment with clamping lever Offsetting tube tolerances The RPG offers the possibility to offset tube tolerances deviations from nominal size by means of an adjusting bolt adjusting wheel at the clamping lever The adjusting bolt has 3 visible marks the factory s setting or neutral position respectively is marked by e Example A tube with an outer diameter of 51 mm is to be processed with the clamping shell set of 50 8 mm As a consequence it is not possible to move the clamping lever right to the stop Therefore the adjusting bolt has to be set towards Now the tube clamping is correct All adjustment possibilities are shown in the following table Tube has exactly the nominal size Tube size smaller than nominal size Tube size larger than nominal size Position of clamping lever The adjustment of the clamping lever is correct The clamping lever sits on the clamping frame tube not clamped It is not possible to turn the clamping lever Re adjustment required towards Result position of adjusting bolt 16 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc G orbitalum tools gmbh Operating instructions RPG 4 5 R
3. gt orbitalum on tools for piping systems simplicity Operating instructions Tube Squaring Machines RPG 4 5 RPG 8 6 Code 790038762 Machine no Translation of original operating instructions All rights reserved in particular the rights of duplication and distribution as well as translation Duplication and reproduction in any form print photocopy microfilm or electronic require the written permission of Orbitalum Tools GmbH Operating instructions RPG 4 5 RPG 8 6 Table of contents Table of contents Page 0 About these instructions 1 0 1 Warning messages 1 0 2 Further symbols and displays 2 0 3 Abbreviations 2 1 Notes on safety 3 1 1 Proper use 3 1 2 Safety regulations 3 1 3 Working safely 4 1 4 Waste disposal environmental protection 4 1 5 Further safety regulations 5 2 Construction of the product 6 2 1 RPG 4 5 RPG 8 6 6 2 2 Accessories 7 2 2 1 Multifunctional tool MFW 7 2 2 2 Tool holder WH 7 2 2 3 Clamping shells 7 3 Characteristics and range of applications 8 3 1 Characteristics 8 3 2 Range of applications 9 4 Technical data 10 4 1 Rating 10 5 Commissioning 11 5 1 Included with the machine 11 5 2 Transportation 11 5 3 Connection requirements 11 6 Operation 12 6 1 Fitting the multifunctional tool MFW and the tool holder WH 13 6 2 Inserting replacing the clamping shells 14 6 3 Clamping the tube 16 6 3 1 Possibilities of adjustment with clamping lever Offsett
4. prevent danger Possible danger Non observance could result in serious injury Restrictions if applicable gt WARNING Measures to prevent danger Dangerous situation Non observance could result in minor injuries gt ATTENTION ATTENTION Dangerous situation Non observance could result in material damage G orbitalum tools gmbh 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 1 0 About these instructions Operating instructions RPG 4 5 RPG 8 6 0 2 Further symbols and displays Symbol Meaning Important Note Notes Contain particularly important information for comprehension Instruction You must take notice of this symbol Request for action in a sequence of actions You have to do something here Single request for action You have to do something here Conditional request for action You have to do something here if the specified condition is met 0 3 Abbreviations Abbr Meaning RPG 4 5 RPG 8 6 Tube Squaring Machine for tubes with an outer diameter of up to 4 5 inches Tube Squaring Machine for tubes with an outer diameter of up to 8 6 inches MFW Multifunctional Tool WH Tool Holder OTCH Quick Tool Change 2 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc G orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 1 Notes on safety Important G orbitalum tools gmbh W
5. 05 are taken back and treated according to legal standards These products have to be send free of charge The return of used devices which pose a health or safety risk for human beings due to soiling during use may be refused The legally compliant disposal of electrical electronic devices that were placed on the market before August 13th 2005 are in the responsibility of the end user 1 5 Further safety regulations Observe country specific regulations norms and guidelines 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 5 2 Construction of the product 2 2 1 O 4 OD ROD Operating instructions RPG 4 5 RPG 8 6 Construction of the product RPG 4 5 RPG 8 6 Feed handle with adjustable dial 9 Tool holder with multifunctional tool Housing 10 Base plate Cover 11 Unlock handles ON OFF switch 12 Clamping lever Stop bolt 13 Adjusting wheel for pre setting Clamping unit the speed Chip container 14 Driving motor Tool support 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc G orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 2 Construction of the product G orbitalum tools gmbh 2 2 Accessories Please check the outer diameter of the tubes before ordering the clamping shells The different standards sometimes involve a special size particularly for tubes in accordance with DIN 2430 2 2 1 Multifunctional tool MFW Included in the standard scope of delivery Two s
6. 1 1 Move the tool towards the tube by means of the feed handle until the tool touches the tube If the cutting edge of the tool is cutting into the entire circumference of the tube 2 Guide the tool further with the same amount of pressure The dial can be set to zero in accordance with the marking on the housing Each division mark corresponds to a feed motion of 0 05 mm 6 7 Switching the RPG off Press the ON OFF switch gt The RPG comes to a stop 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 19 7 Maintenance DANGER Operating instructions RPG 4 5 RPG 8 6 7 Maintenance Danger of death by electric shock Pull out the mains plug before performing any maintenance work Time Activity Before starting work gt Check the tube clamping if the tube is already mounted in the machine At each cleaning gt Clean the clamping shells and the tool supports for the multifunctional tool At each tool change gt Clean the tool support and the multifunctional tool gt Remove any dirt from the bearing surface of the tool holder 20 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 8 Whatto do if 8 1 Problem solving 8 What to do if In the following table you will find possible causes for faults and the appropriate remedies Fault Possible cause Remedy The tool multifu
7. PG 8 6 6 Operation Shifting the 1 Loosen the clamping lever and remove the tube if necessary adjusting bolt 2 Loosen the hexagon socket screw of the adjusting bolt using the Allan key 3 Turn the adjusting bolt towards or 4 Allow the pin to engage into the adjusting bolt and re tighten the hexagon socket screw 5 Now the tube can be clamped in 6 4 Setting the number of revolutions Note The cutting speed recommended by Orbitalum Tools and thus the number of revolutions can be determined in the chapter 6 4 2 6 4 1 Increasing reducing the number of revolutions gt Set the adjusting wheel for presetting the speed to the desired level RPG 4 5 A D RPG 8 6 B D A corresponds to the lowest and D to the highest number of revolutions G orbitalum tools gmbh 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 17 6 Operation Operating instructions RPG 4 5 RPG 8 6 6 4 2 Determining the number of revolutions Take the recommended cutting speed from the table below Standard values Adjusting wheel for the revolutions Machine type Tube OD for presetting the High alloy steel per minute n speed mm inch Level n 1 min RPG 4 5 25 4 1 0 D 31 RPG 4 5 38 1 1 5 C 23 RPG 4 5 50 8 2 0 C 23 RPG 4 5 63 5 2 5 B 14 RPG 4 5 76 2 3 0 B 14 RPG 4 5 88 9 3 5 A 9 RPG 4 5 101 6 4 0 A 9 RPG 4 5 114 3 4 5 A 9 RPG 8 6 50 8 2 0 E 18 RPG 8 6 101 6
8. arning While using electrical tools the following safety measures need to be observed in order to protect against electrical shock risk of injury or fire Read all these instructions before using this electrical tool and preserve the safety instructions carefully 1 Notes on safety The Tube Squaring Machine in the following referred to as RPG is a state of the art machine Using it for purposes other than those described in this manual may cause injury to the user or to others The machine or other equipment may also be damaged Therefore e Always ensure that the machine is in good working condition and always comply with these notes on safety e Keep the complete documentation close by the machine e Generally valid regulations for the prevention of accidents must be observed 1 1 Proper use e Use the RPG exclusively for machining thin walled tubes e The user will be the only person liable for damages caused by improper use 1 2 Safety regulations e Only use the dimensions and materials quoted in these instructions Range of applications see the chapter 3 2 p 9 Other materials should only be used after consulting the Orbitalum Tools customer service department e Read the enclosed safety notes completely and carefully before working with the electric tool Metabo SBE 1010 Plus e Only use authentic Orbitalum Tools spare parts and materials e Check the RPG daily for any externally visible damages or
9. death by electric shock Danger of injury after having actuated the ON OFF switch unintentionally Pull out the mains plug before performing any adjustments or repair and maintenance work Danger of injury by rotating tool support gt Do not reach into the tool support while processing keep wide clothing away from the work area Only operate the machine after the tube has been clamped in the cover has been closed and the chip container has been inserted 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 6 Operation WARNING WARNING G orbitalum tools gmbh 6 1 Fitting the multifunctional tool MFW and the tool holder WH Danger of injury Sharp cutting edges O gt Do not touch the cutting edges when fitting the multifunctional tool Wear safety gloves Screw the multifunctional tool MFW onto the tool holder using a Torx screwdriver Insert the tool holder with fitted MFW laterally into the guiding groove and position it Press the tool holder against the bearing surface of the tool support and at the same time tighten the screw using the Allan key 1 Danger of injury by projecting tool holder Danger of squashing hands damage to the machine gt The tool holder with fitted MFW must not project over the edge of the tool support Before switching on the tube squaring machine RPG make sure that the d
10. defects Have any damages or defects repaired immediately e Work on the electrical equipment should only be carried out by a qualified electrician e Only operate the RPG if the electrical re start prevention is working e Pull out the mains plug before carrying out a tool change or maintenance and repair work 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 3 1 Notes on safety RL 2002 96 EC Operating instructions RPG 4 5 RPG 8 6 1 3 Working safely Play your part in ensuring safety at work Report any changes in operating performance to the responsible person immediately Carry out all work with an awareness of safety Keep the working area tidy Untidiness in the working area may cause accidents When working with the RPG wear protective goggles and safety gloves Tie up long hair hair net do not wear wide clothing Attention Jewelry loose fitting clothing and ties can be caught in rotating parts Make sure that the work piece has been clamped correctly Turn the machine off at the end of each operating cycle and allow the machine to run a stop Before carrying out a tool change cleaning performing any maintenance work adjustments or repair work pull out the mains plug and allow the machine to run to a stop Keep hands away from the tools during processing Pay attention to the surroundings Do not use any electric tools in a damp or wet area Make sure to have good illumination D
11. ectado construido y comercializado bajo observaci n de las siguientes Directivas Maschinen Richtlinie 2006 42 EG EMV Richtlinie 2004 108 EG Niederspannungsrichtlinie 2006 95 EG Folgende harmonisierte Normen sind angewandt The following harmonized norms have been applied Le seguenti norme armonizzate ove applicabili Les normes suivantes harmonis es ou applicables Las siguientes normas armonizadas han sido aplicadas DIN EN ISO 12100 1 2003 DIN EN ISO 12100 2 2003 DIN EN 61029 1 2003 DIN EN 1037 1995 DIN EN 50144 1 1998 DIN EN 55014 1 2003 DIN EN 55014 2 2002 DIN EN 61000 3 2 2001 DIN EN 61000 3 3 2002 im DEE P Markus Tamm Hasan Caglar Managing Director Product Manager 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc orbitalum tools gmbh Orbitalum Tools GmbH Sales Contact Tel 49 0 77 31 792 0 Fax 49 0 77 31 792 524 tools orbitalum com www orbitalum com An ITW Company Plant Division Orbitalum Josef Sch ttler Stra e 17 78224 Singen Germany 790 038 762_04 01 05 10 Orbitalum Tools GmbH D 78224 Singen 2010 Printed in Germany ek orbitalum tools for piping systems
12. ided tool bit with high performance Balinit Futura protective coating against tool wear Usable for all tool holders of the RPG series Article Code MFW P 2 790 038 314 Torx screw 790 086 220 2 2 2 Tool holder WH Fits multifunctional tool 790 038 314 Incl Torx fixing screw Article Possible application Bevel Code Squaring Beveling angle 4 Tool holder WH15 I x 790 038 320 Tool holder WH12 V 45 D 45 790 038 280 Tool holder WH12 V 35 D 35 790 038 282 2 2 3 Clamping shells Not contained in the standard scope of delivery Other dimensions are available upon request Clamping shells applicable with Tube OD mm Tube OD inch Code RPG 4 5 25 40 1 000 790 033 051 RPG 4 5 31 75 1 250 790 033 052 RPG 4 5 38 10 1 500 790 033 053 RPG 4 5 50 80 2 000 790 033 054 RPG 4 5 63 50 2 500 790 033 055 RPG 4 5 76 20 3 000 790 038 056 RPG 4 5 88 90 3 500 790 038 057 RPG 4 5 101 60 4 000 790 038 058 RPG 4 5 114 30 4 500 790 038 059 RPG 8 6 101 60 4 000 790 039 252 RPG 8 6 114 30 4 500 790 039 256 RPG 8 6 141 30 5 563 790 039 257 RPG 8 6 152 40 6 000 790 039 253 RPG 8 6 168 30 6 625 790 039 254 RPG 8 6 219 10 8 625 790 039 255 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 7 3 Characteristics and range of applications Operating instructions RPG 4 5 RPG 8 6 3 Characteristics and range of applications 3 1 Characteristics The RPG is s
13. ing tube tolerances 16 6 4 Setting the number of revolutions 17 6 4 1 Increasing reducing the number of revolutions 17 6 4 2 Determining the number of revolutions 18 6 5 Switching the RPG on 19 6 6 Processing the tube 19 6 7 Switching the RPG off 19 7 Maintenance 20 8 What to do if 21 8 1 Problem solving 21 8 2 Servicing customer service 21 G orbitalum tools gmbh 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc Table of contents Operating instructions RPG 4 5 RPG 8 6 9 EU declaration of conformity 22 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 0 About these instructions 0 About these instructions To allow quick understanding of these instructions and safe handling of the machine all the warning messages notes and symbols used in these instructions are presented here along with their meaning 0 1 Warning messages In these instructions warning messages are used to warn you against the dangers of injury or material damage Always read and observe these warning messages This is a warning symbol It should warn you against dangers of injury Follow all instructions which are identified with this safety symbol in order to avoid injuries or death Warning Meaning symbol Direct danger Non observance could result in death or critical injury Restrictions if applicable gt DANGER Measures to
14. istance between the MFW and the housing is sufficient Close the cover before switching the RPG on 05 10 MT_RPG 4 5 RPG 8 6_BA_04_790038762_04 doc 13 6 Operation Operating instructions RPG 4 5 RPG 8 6 Note To facilitate the adjustment process the tool support of the RPG 4 5 has been provided with 4 visible marks for 1 2 3 and 4 tubes see the illustration below At the RPG 8 6 there are 5 visible marks for 4 5 6 7 and 8 tubes 6 2 Inserting replacing the clamping shells Inserting the lower Select the clamping shells according to the tube diameter clamping shell 1 2 Move the clamping lever to the open position 3 Place the lower clamping shell at the stop bolt 2 4 Swivel the clamping shell around the stop bolt in the direction of the arrow until the unlock handle locks into place 14 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc G orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 6 Operation Inserting the upper 5 Place the upper clamping shell at the stop bolt 3 clamping shell e Swivel the clamping shell around the stop bolt in the direction of the arrow until the unlock handle locks into place Replacing the 7 To replace the clamping shells pull at the unlock handles clamping shells 8 Remove the upper and lower clamping shell orbitalum tools gmbh 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 15 6 Operation 6 3 Operating instructions
15. livery for completeness and transportation damage gt Report any missing parts or transportation damage to your supplier immediately 5 1 Included with the machine e 1 Tube Squaring Machine RPG housing with driving unit e 1 Transportation case e 1 Tool holder Code 790 038 320 with multifunctional tool Code 790 038 314 e 1 Tool set e 1 Set of operating instructions and 1 spare parts list Subject to alterations 5 2 Transportation The RPG is a portable machine Special transportation aids are not required see the illustration Danger of death caused by electric shock and restart of the machine During transportation the ON OFF switch could be actuated inadvertently so that the machine is started Cut off the power supply before carrying out the transportation or a workplace change gt Donothold the machine at the clamping frame during transportation 5 3 Connection requirements The mains supply must meet the following requirements e 1 phase alternating current 200 240 V 50 60 Hz EU or 100 120 V 50 60 Hz EU protection class II e Mains fuse at least 10 A 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 11 6 Operation 12 Note DANGER Operating instructions RPG 4 5 RPG 8 6 6 Operation As the usage of both versions of the tube squaring machine is identical the pictures shown in this chapter solely represent the essential working steps using the RPG 4 5 version Danger of
16. mm inch 25 4 114 3 1 4 5 50 8 219 1 2 8 6 The maximum workable wall thickness is 3 mm 0 118 inch e High alloy steels high grade steel material no 1 40 1 45 according to DIN 17 455 and DIN 17 456 e Non alloy and low alloy steels e Aluminum Others on request 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 9 4 Technical data 10 Operating instructions RPG 4 5 RPG 8 6 4 Technical data 4 1 Rating Rating RPG 4 5 RPG 8 6 Dimensions with drive 525 x 256 x 226 mm 20 7 x 10 x 8 9 inch 630 x 390 x 340 mm 24 8 x 15 4 x 13 4 inch Total weight 10 2 kg 20 5 kg without clamping shells 22 5 Ibs 45 2 Ibs Output 1 35 1 35 HP 1010 W 1010 W 230 V 50 60 Hz EU 230 V 50 60 Hz EU Mains supply 110 V 50 60 Hz EU 110 V 50 60 Hz EU 120 V 50 60 Hz US 120 V 50 60 Hz US Speed max idling speed 8 52 rpm 7 18 rpm Noise level at the workplace Vibration level according to EN 28662 Part 1 Idle running approx 83 dB A 2 5 m s 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc Idle running approx 83 dB A 2 5 m s The noise level measurement was carried out under normal operating conditions according to EN 23741 G orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 5 Commissioning Checking the parts of delivery DANGER G orbitalum tools gmbh 5 Commissioning Check all parts of the de
17. nctional tool is catching during machining Too much feed gt Dismount the tool holder and remove the tube from the machine gt Remove the chip using side cutting pliers and file off the shoulder Feed carefully for further machining Multifunctional tool is loose Tighten the multifunctional tool The motor of the RPG is not running electronics signal light of the motor lights up Restart prevention has been activated Turn the RPG off and back on again Tool tends to vibrate Cutting speed is too high gt Set the number of revolutions cutting speed according to the table High level of vibration Axial or radial play in the components Multifunctional tool is loose gt Check the machine for zero backlash gt Check the multifunctional tool for tightness The machined tube is rough Multifunctional tool is blunt gt Replace the multifunctional tool The clamping unit does not clamp correctly or the eccentric lever has too much too less play Attrition abrasion or the tube diameter slightly deviates from the dimensions actually intended Offset by adjusting with the adjusting device Tool does not turn although engine runs Load limiting device adapter mechanically cut gt Change adapter code 790 038 126 see spare parts list p 6 7 Item No 9 8 2 Servicing customer service For ordering spare pa
18. o not work near combustible liquids or gases Do not carry the electric tool holding it at the cable and do not use it to pull the plug out of the socket Protect the cable against heat oil and sharp edges chips While working on tubes keep the protective cover of the machine closed and insert the chip container Read the enclosed safety notes of the driving motor Metabo 1010 Plus carefully 1 4 Waste disposal environmental protection Dispose of chips and used gear lubricant oil according to the regulations Discarded electric tools and accessories contain a large share of valuable raw and synthetic materials which can be recycled Therefore Electrical electronic devices which are marked with the symbol to the left may not be disposed of with household waste in accordance to the EU directive 2002 96 EC By actively using the offered return and collection systems you actively contribute to the reuse recycling and utilization of electrical electronic devices 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 1 Notes on safety G orbitalum tools gmbh Electrical electronic used devices contain parts which must be handled selectively according to the EU directive Separate collection and selective treatment is the basis for environment friendly disposal and the protection of human health Our products that were sold to you after August 13th 20
19. rts see the separate spare parts list For problem solving please contact your branch office directly Please give the following details e Machine type RPG 4 5 and or RPG 8 6 e Machine number see the identification plate G orbitalum tools gmbh 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc 21 9 EU declaration of conformity Operating instructions RPG 4 5 RPG 8 6 Die Bauart der Maschine The following product Il seguente prodotto Le produit suivant 9 EU declaration of conformity EG Konformit tserkl rung Orbitalum Tools GmbH Declaration of conformity Josef Sch ttler Stra e 17 Dichiarazione di conformita 78224 Singen Deutschland D claration de conformit Tel 49 0 77 31 792 0 Declaracion de conformidad Fax 49 0 77 31 792 524 According to machine guideline 2006 42 EG MaschR Appendix II A RPG 4 5 Tube Squaring Machine RPG 8 6 Tube Squaring Machine El producto siguiente Seriennummer Series number Numero di serie Nombre de s rie Numero de serie Baujahr Year Anno Ann e A o Singen 22 01 2010 22 ist entwickelt konstruiert und gefertigt in bereinstimmung mit folgenden EG Richtlinien was designed constructed and manufactured in accordance with the following EC guidelines stata progettato costruito e commercializzato in osservanza delle seguenti Direttive a t dessin produit et commercialis selon les Directives suivantes ha sido proy
20. uitable for squaring tube ends made of metallic materials It has the following characteristics Pipe end preparation for welds conforming to standards Tool holding system QTC Quick Tool Change Rapid locking for fixing the tool holder to the tool support Only one multifunctional tool is necessary for Different tube wall thicknesses up to 3 mm Different tube materials exclusively ferritic materials Multifunctional tool Cutting geometry adapted to application Multi cutting tool Only one screw is needed to fix and secure the tools Tool coating TiN Machine Hand operated Drive Twistable detachable Speed controlled electric motor with speed stabilization Restart protection to prevent the machine from starting in an uncontrolled way after it has been re connected to the electric mains or after the voltage supply has been re established after a power failure Quick clamping system for tubes with adjusting facility Quick change system for clamping shells Advance Total 15 mm Per revolution 3 mm Dial with zero position The cover and the chip container guarantee clean working 05 10 MT_RPG 4 5_RPG 8 6_BA_04_790038762_04 doc orbitalum tools gmbh Operating instructions RPG 4 5 RPG 8 6 Work area Tube materials G orbitalum tools gmbh 3 Characteristics and range of applications 3 2 Range of applications Machine type Outer diameter OD RPG 4 5 RPG 8 6
Download Pdf Manuals
Related Search