Home

Installation and operating instructions

1. Upload a set of tasks to the FarmPilot portal The following notification will appear Start uploading task data 3 Confirm gt The data are being loaded gt The transferred task data will no longer be displayed on the terminal gt Anew folder is being created on the USB flash drive TaskData_work serial number Backup copies of the tasks sent to the FarmPilot portal will be created in this folder You have uploaded a set of tasks to the portal 8 9 Important files stored on the USB flash drive All task data field data and machine data will be saved on the USB flash drive This makes it possible to transfer these data between the terminal and the Farm Management Information System All files have standardised names which may not be altered The folders that must be stored on the USB flash drive vary depending on whether you are using the terminal in conjunction with the FarmPilot portal or transfering the data from the Farm Management Information System using a USB flash drive Important files The files specified here may appear in various folders TASKDATA xml A file containing all task data stored in the Farm Management Information system The file will be saved from the Farm Management Information System either onto the hard drive of the farm computer or onto a USB flash drive 88 Copyright Muller Elektronik GmbH amp Co KG TaskManager application Miemuetter ey lectronics Important fi
2. Copyright Muller Elektronik GmbH amp Co KG 45 Configuring the terminal in the Service application MUELLER U Configuring FarmPilot l E MUELLER We CAN do it Zooming out for camera images Activating automatic camera mode In automatic mode the camera images will be automatically displayed if a sensor sends a signal to do so This only works if the vehicle is equipped with a suitable sensor Saving camera settings Exiting camera You can press the function keys even if the camera is set to full screen mode Procedure M You have connected and activated the camera 1 Switch to the Camera screen ED Service gt The following screen will appear ve 2 Use the function keys to control the camera 7 16 Configuring FarmPilot FarmPilot is an internet portal which allows software on a farm computer to exchange data with machines via a mobile phone network Operating data are stored in a central location on the portal and are presented clearly to the user Before you can use FarmPilot in conjunction with your terminal you must complete the following steps Purchase a SIM card and have it activated Activate FarmPilot Enter your FarmPilot access data Refer to the following chapters to learn how to perform these steps 46 Copyright Muller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application tectronics Configuring Fa
3. You can start the task you copied gt 75 8 3 2 Adopting an existing task D D amp a fem Worker 7 f fertilization 2 00 Field 2 Fertilization 2 00 Field 2 fertilization 2 00 Field 2 Mueller 2 00 Field 2 nd marked as a copy with an asterisk You can process one of the tasks that appears on the Task list screen 66 Copyright Muller Elektronik GmbH amp Co KG TaskManager application Miemuetter eu lectronics Step 2 Selecting a task to process We CAN do it The tasks may originate directly from the Farm Management Information System from the FarmPilot portal or from the USB flash drive The following options are available to you Resume an existing task Splitting a task that has already been started Resuming a task Procedure M You have copied the data from the Farm Management Information System to the USB flash drive VI You have inserted the USB flash drive into the terminal 1 Switch to the Master data screen The following screen will appear 3 af DIES 9 Fields 1 28 Farms B customers wip Farm equipment CB worker GF Products i Me TM 02 00 60 TC 00 13 01 2 Click on the Tasks line The following screen will appear Zen la fertilization 2 00 Field 2 amt we fertilization 2 00 Field 2 W Mueller SS 2 00 Field 2 fem Worker gt gt The list
4. This signal word identifies actions which could lead to operational malfunctions if performed incorrectly These actions require that you operate in a precise and cautious manner in order to produce optimum work results There are some actions that need to be performed in several steps If there is a risk involved in carrying out any of these steps a safety warning will appear in the instructions themselves Safety instructions always directly precede the step involving risk and can be identified by their bold font type and a signal word Example 1 NOTICE This is a notice It warns that there is a risk involved in the next step 2 Step involving risk Copyright M ller Elektronik GmbH amp Co KG 7 For your safety MOELLER User requirements l E MUELLER We CAN do it 1 3 User requirements Learn how to operate the terminal correctly The terminal must not be operated by anyone who has not read the Operating Instructions Please read and carefully observe all safety instructions and warnings contained in these Operating Instructions and in the manuals of any connected machines and farm equipment 1 4 Intended use The terminal is intended exclusively for use in agriculture as well as in wine growing fruit cultivating and hop growing operations The manufacturer cannot be held responsible for any installation or use of the terminal that deviates from or exceeds the scope of intended use The manufacturer
5. 1 B plant protection 2 00 Field 2 cultivator seeder W Mueller tractor 1 K 2 00 Field 2 tractor 2 fem Worker 1 tractor 3 4 202 00 l ha Mix Water AVENTIS C Gop ME_ISO_SPRAYER Se Worker 1 5 plant protection ety Filling Emptying SR ME_ISO_SPRAYER g combine Yolume counter 63 00 0x2000000000000000 Surface counter 9 34 ha 2 Distance counter 3 89 km 0x00000000000000 Time counter 0 01 h 3 Click on the desired machine or equipment on the list For instance a tractor with which you wish to pull a sprayer The following screen will appear gt TSk 1 BE ME_ISO_SPRAYER B plant protection 2 00 Field 2 01 03 2011 15 26 00 W Mueller 01 03 2011 15 27 50 K 2 00 Field 2 fem Worker 1 4g 202 00 l ha Mix Water AVENTIS C y ME_ISO_SPRAYER amp worker 1 5 plant protection ets Filling Emptying RMEISO SPRAYERS volume counter 117 001 Surface counter 15 56 ha Distance counter 6 48 km Time counter 0 02 h You will find the following information below the name of the machine For activated machines Date and time of activation For deactivated machines Date and time of deactivation 4 Add additional machines or farm equipment gt You have selected a machine Procedure 2 You can reactivate a deactivated machine as follows 1 Click on the following line on the Task data screen 2 Select a deactivated machine from th
6. 8 7 1 Stopping a task When you stop a task FarmPilot will consider this task to be fully completed Therefore you should only stop tasks if they have been completed Procedure 1 Switch to the Task data screen 2 B Stop task gt The task will be stopped gt The task will be marked red on the Task list screen 8 7 2 Pausing a task You can pause a task if you need to interrupt your work but have not yet completed the task A task will only be paused if you start another task Copyright M ller Elektronik GmbH amp Co KG 85 TaskManager application me MUELLER Step 6 Stopping work l E MUELLER We CAN do it Procedure VI You have started a task and are on the Task data screen CE 913 B plant protection 2 00 Field 2 X Fields a 28 Farms W Mueller EM customers 82 00 Field 2 wip Farm equipment fem Worker ED worker ag 202 00 l ha Mix Water AVENTIS C O Products Gay ME_ISO_SPRAYER amp worker 5 plant protection gy Filling Emptying a ME_ISO_SPRAYER volume counter 56 00 Me Surface counter 0 28 ha So Distance counter 0 12 km TM 02 00 60 Time counter 0 01 h TC V 00 13 01 1 Switch to the Task list screen while the task is started gt The following screen will appear T122 plant protection 1 00 Field 1 B plant protection 2 00 Field 2 B plant protection 2 00 Field 2 W Mueller
7. Memuciter pe eet lectronics Step 3 Entering and saving task data We CAN do it 8 4 Step 3 Entering and saving task data Task data are entered in two different locations In the Farm Management Information System In the TaskManager application In the TaskManager application you can only select data which you have previously created in the Farm Management Information System You can assign these data to the individual tasks You can only alter the task data of a task if you have created a new task and have not saved it yet 8 4 1 Entering task data You can only enter the task data that you have created in the Farm Management Information System and saved on your USB flash drive The task data created in the Farm Management Information System will be saved in the following categories Icon Name of the category Comment Customer Farm business Field Person in charge Worker Cannot be selected until the task has been started 2 is Bo Z B Bo Machine Cannot be selected until the task has been started Product and rate Measure U The names used here may not always correspond to the category names used in the Farm Management Information System This is due to the fact that the names vary with each specific Farm Management Information System used For instance if you did not create any data in a particular category the following screen will
8. 4 C 0x87 XAG CSOOGOCAGGOGA TaskManager HH OXF BxABB982089C A490AHDF TRACK Leader Im BxiC 6xABG617GB8C49BAGF You are now in the selection menu gt When the terminal is connected to an ISOBUS job computer they will be now loaded The progress of this process is indicated by the progress bar next to the job computer icon The time taken to complete this process depends on the number of connected job computers 4 Wait until all job computers have been loaded 22 Copyright Muller Elektronik GmbH amp Co KG MUELLER Basic control principles tectronics Using the function keys We CAN do it gt The following screen will appear sa Service gt 3 4 4 ry 8x26 BxABBBLDBHACAHBAHF C p s p j O s57h2de 0x87 XAG CSOOGACAOOOGA TaskManager zm OXF BxABBGS2GGGC49GAGF TRACK Leader Sm Bx1C 6xABGG17GG8C49BAGF The job computers are loaded when no more progress bars are displayed 5 In the selection menu you can select which application you wish to display next a 6 Select the Service line The Service line must be framed by a black square m Service Sm x26 xAseo1DeeGC4o05919 P 7 Click on the Service line gt The following screen will appear 2 File management Driver settings f Plugin settings 7 License management ME Terminal Y 03 90 00 gt You have o
9. A at 13 8 V without external equipment At terminal 30322528 Typically 0 8 A at 13 8 V without external equipment Display VGA TFT colour display display size diagonal 26 cm resolution 640 x 480 pixels 32 bit ARMO20T up to 400 Mz Boot USB 128 MB Keyboard 17 illuminated keys plus rotary knob Outputs 2 x CAN 1x USB 1 x RS232 2 x M12 for two analogue cameras optional 9 4 2 Pin assignment of port A Port A is a 9 pin D sub port of the ISO agricultural machinery interface CAN Copyright M ller Elektronik GmbH amp Co KG 91 9 4 3 92 Maintenance and servicing MUELLER lectronics Technical specifications we CAN do it Vin voltage supply Vin ground 1 Signals marked with 1 correspond to the CiA assignment CAN in automation Both signals CAN_L and CAN_L and or CAN_H and CAN_H are linked internally and used to loop the CAN bus through Assigning CAN_EN_in to the supply potential Vin enables the terminal to be switched on The signals Vin and CAN_GND are directly linked with both connectors therefore it is crucial to avoid differences in potential between the pins of these two connectors 2 is compliant with TBC_Pwr in ISO 11783 When the terminal is switched on this pin is under voltage supply voltage minus approx 1 2V Pin assignment of port B Port B is a 9 pin D Sub port The connector can be used for the following purposes depending on its assignmen
10. CAN do it Display layout in the selection menu 6 Opening applications in the selection menu In the selection menu you can choose which application you wish to view on the display You can open the selection menu at any time This will not close the application currently running Controls Open the selection menu Press again open the most recently activated application Display the application in the header of the split display Display the application in the main section of the display 6 1 Display layout in the selection menu The display is split into the following sections Function icons left and right Applications section in the middle between the function icons 1 service FH 4 0x26 r 4 s57 h2de 8x87 xAG CSOHOOCAOOOAA TaskManager OXF BxABsGsS260BC40BAGF Field Nav 8x1D 6xAGGG17E8EC46GRGF B amp EafieldNoy TRACK Leader BxiC 8xAs6617006C490RGF Sections in the selection menu 1 Name of an application 4 ISO ID of the application ISO name of the application 2 Function icons on the left Selection 26 Select an application which will later be displayed in the header Selection The selected application is displayed in the header The selected application is displayed on the main display Function icons on the right Open an application on the main display Q Cursor Open the selected application
11. Muller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application lectronics Activating and deactivating applications We CAN do it e EP voune e Time zone 0 Time zone Greenwich Mean Time GMT 1 GMT 1 hour Germany 1 GMT 1 hour Measurement units Metric Displays all units in metrical system Displays all units in imperial system Displays all units in US system Keyboard brightness Ka Setting the level of keyboard brightness in percent 7 6 Activating and deactivating applications In the Service application you can activate and deactivate other applications that are installed on the terminal The applications are installed in packages in so called plugins A plugin can contain several applications You can for example deactivate a plugin if you do not want to use it Then the plugin will not be displayed in the selection menu Name of the plugin Includes the following applications TaskManager TaskManager TRACK Leader TRACK Leader II SECTION Control TRACK Leader TOP HEADLAND Control VARIABLE RATE Control FIELD Nav FIELD Nav Procedure This is how you activate and deactivate plugins 1 Switch to the Plugin settings screen Service Plugin settings Copyright Muller Elektronik GmbH amp Co KG 33 Configuring the terminal in the Service application nn ii MME mueLLER 7 Activating licenses for full versions of the software lectronics We CAN do
12. a new task Copy existing task Split stopped task Start task Stop task Confirm Save task data Select worker Deactivate worker Select machine Copyright Muller Elektronik GmbH amp Co KG 53 TaskM licati askManager application MUELLER Basics lectronics We CAN do it Start navigation to field The function icon is grey when the function has been deactivated Start navigation to unloading location Only appears if your terminal has the Slave status within a group of vehicles The function icon is grey when the function has been deactivated Enter filled capacity Enter emptied capacity 8 1 5 Setting up the operation mode for the TaskManager application The TaskManager application can be run in two different modes ISO mode SC mode In ISO mode the TaskManager will have full functionality However the TaskManager s functionality is limited in SC mode Use this mode when you are not using the TaskManager Features of SC mode The parameters of the machine will be reloaded every time the terminal is restarted When you open the TaskManager in SC mode only the name of the connected machine will be shown on the display Procedure You can change the mode of the TaskManager application as follows 1 Switch to the Settings screen p gt TaskManager Ea 54 Copyright M ller Elektronik GmbH amp Co KG TaskManager
13. ae Machine is activated green background no icon If you are processing the task using a machine not intended for this purpose no icon will appear before the machine s name Procedure 1 You can select a machine from a list as follows VI You have started a task 1 Click on the following line on the Task data screen The following screen will appear ny Be TSk 1 PMIME_ISO_SPRAYER plant protection 2 00 Field 2 01 03 2011 15 26 00 Per su W Mueller SS 2 00 Field 2 fem Worker 1 ag 202 00 I ha Mix Water AVENTIS C Gay ME_ISO_SPRAYER amp Worker 1 plant protection ety Filling Emptying a ME_ISO_SPRAYER volume counter 63 00 aa Time counter 0 01 h The screen contains a list of all machines which you have assigned to this task If you process the task using the assigned machine the machine displayed will be activated immediately If you are processing the task using a machine not assigned to this task no icon will appear before the machine s name gt Ifthe machine ME_ISO_Spritze appears at this point you have not created an ISO machine in your Farm Management Information System 6 2 LS Add machines Copyright M ller Elektronik GmbH amp Co KG 77 TaskManager application mn MUELLER Step 4 Starting a task l E MUELLER We CAN do it gt A list of machines and farm equipment will appear F a
14. bought a terminal without a GSM modem you can retrofit it with a GSM modem later Please call our Customer Services department 3 4 Correctly interpreting information on the nameplate On the reverse of the terminal you will find a nameplate sticker On this sticker you can find all the information you need to definitively identify the product Have these details ready when you contact Customer Services lektronik www mueller elektronik de o K Nr DC 2 mw SW 5 ME NR SN Nameplate on the reverse of the terminal 1 Customer number 4 Operating voltage If the product was manufactured for an The product may only be connected to agricultural machinery manufacturer the voltages within this range agricultural machinery manufacturer s item number will be shown here 2 Hardware version 5 Software version If you update the software this version will no longer be up to date 3 Muller Elektronik item number 6 Serial number Copyright Muller Elektronik GmbH amp Co KG 11 Mounting and installation MEmueLLER Instructions on retrofitting lectronics We CAN do it 4 Mounting and installation Mount the terminal and all additional components in the following order 1 Mount the terminal in the tractor cab 2 Connect the terminal to the basic equipment 3 Connect the terminal to other components Refer to the following chapters to learn how to perform these steps 4 1 Instruct
15. camera connections You can find out the terminal version you have on the connections on the terminal rear side gt 14 Software All applications of Muller Elektronik available are installed on the terminal But first you must activate some of them See also Activating licenses for full versions of the software gt 34 The following applications are activated SERVICE this application configures the terminal TaskManager this is the certified ISOBUS Taskcontroller from M ller Elektronik In this application you can use the terminal for processing all tasks previously planned on the PC 15011783 VT Interface for controlling the ISOBUS job computers The terminal is compliant with ISOBUS standard ISO 11783 This terminal can be used as the control unit independently of the manufacturer as an independent terminal on all machines that meet the requirements of this ISOBUS standard You can test the following application for 50 hours free of charge TRACK Leader a modern system enabling the driver of an agricultural vehicle keep exact parallel lanes on the field SECTION Control automatic boom section switching Additional module for TRACK Leader HEADLAND Control with this application you can also drive in parallel around the field in headland Additional module for TRACK Leader VARIABLE RATE Cont with this application you can work with prescription maps saved as shp files Additional module for TRACK Lead
16. cannot be held liable for any personal injury or property damage resulting from such improper use All risks involved in engaging in improper usage lie solely with the user Intended use also includes the adherence to the conditions for operation and repairs prescribed by the manufacturer The manufacturer cannot be held liable for any personal injury or property damage resulting from such non observance All risk involved during improper use lies with the user All applicable accident prevention regulations and all other generally recognized safety industrial and medical rules as well as all road traffic laws must be observed Any unauthorized modifications made to the unit will void the manufacturer s warranty 1 5 EC declaration of conformity This product has been manufactured in conformity with the following national and harmonised standards as specified in the current EMC Directive 2004 108 EC EN ISO 14982 8 Copyright Muller Elektronik GmbH amp Co KG MUELLER About these Operating Instructions lectronics Applicability We CAN do it 2 About these Operating Instructions 2 1 Applicability These Operating Instructions apply to the following terminals Terminals from hardware version 3 0 0 Software from version 3 90 of the Service application 2 2 Target group of these Operating Instructions These Operating Instructions are intended for personnel entrusted with installing and operating the terminal 2 3
17. contains an overview of the tasks stored on the USB flash drive 3 Click on the desired task It does not matter what icon is used to mark the task You can resume any tasks Copyright Muller Elektronik GmbH amp Co KG 67 We CAN do it TaskManager application MUELLER Step 2 Selecting a task to process MEMELER onics The following screen will appear TSK131 I fertilization 2 00 Field 2 fertilization 2 00 Field 2 Ooo W Mueller K 2 00 Field 2 fem Worker 4 268 00 I ha AHL 28 66917572ter Gay ME_ISO_SPRAYER amp worker 5 fertilization fertilization 2 00 Field 2 Mueller 2 00 Field 2 fem Worker gt The task data have already been filled in for this task You will no longer be able to alter the data You can now read the following chapter Start task gt 75 Splitting an order that has already been started Use this function in the following instance You have already processed a task and traveled over a portion of the field However you have realized that you wish to process the remainder of the field using a different product or alter the concentration You will not be able to alter the products for a task that you have already started Therefore you will have to split the task Splitting will turn the original task into two tasks Processed portion of the order keeps the name of the original order It contains all information created during the comp
18. first field next to the icon sg 3 Enter the desired rate N a 4 a Confirm and save your entry gt The machine will adopt the rate Selecting the task processing phase Setting the task processing phase allows you to calculate the tasks more accurately The phase of task processing is visible on the Task data screen The following phases exist Driving time to field Preparation Working time Break Repair time Copyright Muller Elektronik GmbH amp Co KG 81 TaskManager application Step 5 Using the TaskManager application during work Procedure 1 Click on the following line on the Task data screen a TSK serial task number D IESE B fertilization 2 00 Field 2 BP Tasks A Fields a 28 Farms W Mueller CB customers K 2 00 Field 2 sip Farm equipment fem Worker B worker 94 268 00 l ha AHL 28 66917572ter GF Products MUELLER lectronics We CAN do it Gay ME_ISO_SPRAYER 2 worker 5 fertilization ets Filling Emptying W ME_ISO_SPRAYER Me TM 02 00 60 TC 00 13 01 The following screen will appear etsai os B fertilization 2 00 Field 2 Preparation Ga working time W Mueller Break K 2 00 Field 2 Repairing time fem Worker 4g 268 00 I ha AHL 28 66917572ter Gay ME_ISO_SPRAYER worker 5 fertilization ets Filling Emptying W ME_ISO_SPRAYER 2 Click
19. inal i ice applicati MUELLER U Configuring FarmPilot l E MUELLER We CAN do it Password Password for FarmPilot Provider Opens a screen where the GPRS connection can be configured With most mobile phone providers this configuration occurs automatically If the access data for the GPRS connection differ with your provider you can configure the connection manually You can find precise instructions in the chapter Configuring the GPRS connection manually gt 48 Server Server address The server address cannot be altered Log Switches logging on and off Switch on logging only when prompted to do so by Customer Services Procedure 1 Open the Service application gt Service 2 cs Open the access data screen for FarmPilot The following screen will appear a Username Den Password Y Provider Server fal Log ME TPD V02 02 02 TPI V02 02 00 3 Click on the line with the desired parameter 4 Configure parameter 7 16 3 Configuring the GPRS connection manually In this chapter you will learn how to configure the GPRS connection manually With most SIM cards the GPRS connection will be configured automatically The GPRS connection must be manually configured in the following instances You have bought a new SIM card The terminal does not recognise your mobile phone provider Your mobile phone provider has altered the access data for the GPRS connec
20. l ha AHL 28 66917572ter GP Products Qa ME_ISO_SPRAYER worker 5 fertilization ets Filling Emptying SR ME_ISO_SPRAYER Me TM 02 00 60 TC 00 13 01 The task has a new status Green task started The following function icons will appear Stop task E Navigate to field You have started the task You now have the following options You can select machines gt 76 You can select workers gt 79 You can let the application navigate you to the field Only if FIELD Nav has been activated To learn how to do so read the FIELD Nav operating instructions You can stop the task gt 85 8 5 1 Selecting the machine This step requires that you select the machines and farm equipment which will be used to process the task You can add any number of machines and farm equipment The terminal records the length of time worked by the machines you added eon er Add machine Reactivate deactivated machine press and hold Fg Deactivate machine Icons Machines can be activated or deactivated For each machine the terminal calculates the length of time for which it was activated The icon preceding the name of the machine indicates whether the machine is activated or deactivated 76 Copyright Muller Elektronik GmbH amp Co KG MUELLER TaskManager application Step 4 Starting a task We CAN do it ae Machine is deactivated red background
21. on the desired phase of task processing The new phase is visible on the Task data screen 8 6 4 Evaluating counters When you start a task you can evaluate the counter while you are spreading your mix The counter will appear on the Task data screen 82 Copyright Muller Elektronik GmbH amp Co KG TaskManager application ME mueELLER Ber Sheer lectronics Step 5 Using the TaskManager application during work We CAN do it 8 6 5 Procedure 8 6 6 Example 1 Example 2 Controls Procedure Brass B fertilization 2 00 Field 2 Ye Fields a 28 Farms W Mueller B customers 2 00 Field 2 wip Farm equipment E fem Worker B worker 94 268 00 l ha AHL 28 66917572ter GF Products Gay ME_ISO_SPRAYER Worker 5 fertilization ets Filling Emptying P ME_ISO_SPRAYER volume counter 10 00 Me Surface counter 0 80 ha Distance counter 0 33 km TM 02 00 60 Time counter 0 00 h TC V 00 13 01 Task data screen with counter The values gathered by the counter are updated two to three times per minute The counters displayed depend on which machine is connected Displaying the counters of a machine 1 Switch to the Task data screen 2 Click on the following line on the Task data screen gt A screen will appear with the selected machines 3 Click on the desired machine The counters of the machine you clicked on will appear on the Ta
22. task on the terminal Copy an existing task and save the copy as a new task Creating a new task Procedure 1 Switch to the Master data screen Copyright Muller Elektronik GmbH amp Co KG 63 We CAN do it TaskManager application MUELLER Step 2 Selecting a task to process ME MuE ER onics The following screen will appear BIES X Fields 28 Farms B customers wip Farm equipment CB worker GF Products E ME TM 02 00 60 TC 00 13 01 2 Click on the Tasks line The following screen will appear n r la fertilization 2 00 Field 2 mt we fertilization 2 00 Field 2 W Mueller ao Field 2 Worker The Task list screen may show tasks that have already been created as shown in the picture 4 3 Create a new task 64 Copyright Muller Elektronik GmbH amp Co KG MUELLER lectronics We CAN do it TaskManager application Step 2 Selecting a task to process The following screen will appear i TSK 2011 02 24 11 54 18 Li ag u er N fa I fertilization 2 00 Field 2 fertilization 2 00 Field 2 Mueller 2 00 Field 2 fem Worker gt The new task was named by the terminal with the current date and time The task has not been saved yet gt You have created a new task You now have the following options You can fill the task w
23. the information about the selected task The Task data screen will be displayed when you select or create a task on the Task list screen 58 Copyright M ller Elektronik GmbH amp Co KG TaskManager application MUELLER ne lectronics Basics we CAN do it You can identify the Task data screen by this icon You will find the icon in the upper section of the screen The colour of the icon will vary depending on whether the task has been started or newly created Green the task displayed has been started Yellow the task displayed has not been started RSKI32 K131 Hoo aaa fertilization 2 00 Field 2 3 i Mueller 5 SS 2 00 Field 2 Za de ME_ISO_SPRAYER Task data screen 1 Name and number of the task 4 Cursor Serial task number Selects a line that you can click on using the TSK means TASK rotary knob 2 Task processing stage Function icons section Indicates what stage of completion the task is Icons that can be pressed on this screen at gt 81 3 Task data section 6 Counter section Contains detailed information about the Only appears when you start the task selected task The task data section may also contain the following icon This means that the task data also contain an application map The icon is used for information purposes only 8 1 7 Exporting machine settings for the Farm Management Information System Before preparing an order in the
24. to grips with the controls Terminal controls 1 Rotary knob 3 Keys 2 Function keys Controls Rotary knob The rotary knob is located in the top right hand corner of the terminal Control with the rotary knob may vary slightly between the different applications You can use the rotary knob to perform the following actions ai 1 1 Turning the rotary knob Move the cursor up and down Change a parameter value E 1 a Pressing the rotary knob Click on the selected line Activate parameter Confirm input Function keys Operating the function keys is the same across all applications EP Performing the functions depicted on the display Switch the terminal on and off de Has no function Copyright M ller Elektronik GmbH amp Co KG 21 Basic control principles MUELLER Initial start up l E MUELLER We CAN do it lt a gt Has no function ED Exit screen Cancel input Hide warning messages and alerts Open the Selection menu application Exit the Selection menu application 5 2 Initial start up Procedure This is how you start the terminal for the first time VI You have mounted and connected the terminal 1 Switch on the terminal 2 Wait for approx 15 seconds until all applications have been loaded 3 CD Open the Selection menu application gt The following screen will appear Service 0x26 XAOOGLDAGOCAGOAOF P La
25. using the rotary knob Copyright M ller Elektronik GmbH amp Co KG MUELLER Opening applications in the selection menu ecironies Opening applications We CAN do it 6 2 Opening applications You can perform the following actions in the selection menu Open an application Display an application in the header of the split display Procedure East 1 Set which application is to be displayed in the header of the split display gt The function icon of the selected application is marked with a dot on the left hand side AH j D 2 Start the application for the main display There are several ways to do so a With the rotary knob Select the desired application E u Open the selected application b Using the function keys on the right hand side EA Both applications will appear on the display Display the application shown next to the function icon 6 3 Segmentation of the display The display of the terminal is split into two sections A different application is displayed in each section This allows you for example to control the tractor on the field and monitor the field sprayer at the same time This means that you will not need an additional terminal X XI I ZELL IT N aeeusume o 18 6 Tom o ae zZ mich Segmentation of the display Header informative section 2 Main screen section used for control The header allows you to display i
26. 2 00 Field 2 fem Worker 4 202 00 l ha Mix Water AVENTIS C Gay ME_ISO_SPRAYER amp Worker 5 plant protection ets Filling Emptying sh ME_ISO_SPRAYER plant protection 1 00 Field 1 5 1 00 Field 1 fem Worker The active task is marked green 2 Click on any task preferably one that has been stopped The following screen will appear F TSK121 B plant protection 1 00 Field 1 B plant protection 1 00 Field 1 B plant protection 2 00 Field 2 W M ller amp 1 00 Field 1 fem Worker 4g 202 00 I ha Mix Water AVENTIS C Gay ME_ISO_SPRAYER amp worker 5 plant protection plant protection 1 00 Field 1 Hb Maker ax 1 00 Field 1 Worker 86 Copyright Muller Elektronik GmbH amp Co KG TaskManager application Miemuetter 2e SRE lectronics Step 7 Transferring completed tasks to the Farm Management Information System We CAN do it 3 es Start task gt The active task will be paused and the task you have selected will be started 4 E Stop task gt The task will be stopped gt The original task will be marked yellow on the Task list screen D Jplant protection 1 00 Field 1 B plant protection 2 00 Field 2 plant protection 1 00 Field 1 W M ller 1 00 Field 1 fem Worker gt The paused task is now marked yellow 8 8 Step 7 Transferring completed t
27. AS EGNOS Satellite 1 primary DGPS satellite The DGPS Receiver will connect to this satellite in the first instance Satellite 2 secondary DGPS satellite The DGPS Receiver will only connect to this satellite in the event that the primary satellite fails 38 Copyright Muller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application GPS Receiver We CAN do it Your satellite selection will depend on which satellite currently has the best availability in your region Potential values Auto The software automatically selects the current best satellite This setting is not recommended as it slows down start up of the DGPS Receiver Name of the satellite Steering This parameter activates the Automatic steering assistance function in the GPS Receiver Potential values On Activates automatic steering assistance Off Deactivates automatic steering assistance Correction signal Type of correction signal for the DGPS Receiver Potential values WAAS EGNOS Correction signal in Europe and in North America E DIF Internal calculation of correction data This setting is required outside of the EU and the USA To use e Dif you will require a special version of the DGPS Receiver A100 You can order this this DGPS Receiver from Muller Elektronik with the item number 30302464 Terrain compensation Under this parameter the terrain compensation GPS TILT Mo
28. CAN do it Tasks that have not been started yet Tasks that have not been started yet and are tasks which are stored on the USB flash drive but have not yet been started These tasks may include Newly created tasks Copies of existing tasks if the name of the task is preceded by an asterisk Tasks imported via the FarmPilot portal or the Farm Management Information System which have not yet been started Paused tasks B Paused tasks are tasks which have been interrupted and not fully completed A task will be paused automatically if another task is started while the first task is still in progress Paused tasks are displayed in the FarmPilot portal as not yet completed Started tasks B Started tasks are tasks that have been started and are currently being processed Stopped tasks B Stopped tasks are tasks that have been stopped As a rule these are tasks which have been completed However the program is not capable of verifying whether the tasks have been fully completed Therefore only stop a task if you have completed it Stopped tasks are displayed as completed tasks in the FarmPilot portal Tasks processed by the Master Appears only in cooperation with the FarmPilot portal All tasks processed by the fleet leader Master will be labeled as such Every time the Master starts to process a new task you will be notified by a pop up window Task data screen On the Task data screen you can find all
29. Farm Management Information System for the TaskManager application the Farm Management Information System must know the unique number of the job computer mounted on the agricultural machine To deliver this number to the Farm Management Information System you need to create a blank order on the terminal Then you have to open this order in the Farm Management Information System When to perform You must perform this step in the following instances Before the first start up When connecting the terminal to a new machine Copyright Muller Elektronik GmbH amp Co KG 59 Basics Mode of operation Procedure 60 TaskM licati askManager application MUELLER lectronics we CAN do it When changing the machine parameters in the jobcomputer In this step all parameters stored in the job computer of the agricultural machine are saved in an XML file These data are provided with a unique ID number The unique ID number is also the serial number of the connected jobcomputer You can find it in the Selection menu application You have to repeat this step once more for each ISOBUS capable agricultural machine M You have connected the terminal to the jobcomputer of the machine that you wish to add to the master data M You have configured the machine 1 Insert an empty USB flash drive into the terminal 2 Create a Task data folder on the USB flash drive gt 62 3 Create a new task gt 63 You do not ne
30. Layout of operating instructions The operating instructions explain step by step how you can perform certain operations with the product We use the following symbols throughout these Operating Instructions to identify different operating instructions Actions that must be performed in succession Result of the action This will happen when you perform an action Requirements In the event that any requirements have been specified these must be met before an action can be performed Result of an operating instruction This will happen when you have completed all steps 2 4 Layout of references If any references are given in these Operating Instructions they will appear thus Example of a reference gt 9 References can be identified by their square brackets and an arrow The number following the arrow shows you on what page the chapter starts where you can find further information Copyright M ller Elektronik GmbH amp Co KG 9 Product descripti roduct description MUELLER Performance description l E MUELLER we CAN do it 3 Product description 3 1 Performance description Hardware The terminal is available in two hardware versions With GSM modem and with camera connections Complete functionality Itis the prerequisite for work with the FarmPilot portal On the rear side you can find two camera connections and one connection for the GSM antenna Without GSM modem and without
31. MUELLER lectronics we CAN do it Installation and operating instructions COMFORT Terminal Version V3 20111208 30322527 02 EN Read and follow these operating instructions Keep these operating instructions in a safe place for later reference Imprint Document Copyright Installation and operating instructions Product COMFORT Terminal Document number 30322527 02 EN From software version 3 90 Original language German M ller Elektronik GmbH amp Co KG Franz Kleine Stra e 18 33154 Salzkotten Germany Phone 49 0 5258 9834 0 Fax 49 0 5258 9834 90 Email info mueller elektronik de Homepage http www mueller elektronik de MUELL ER Contents lectronics we CAN do it Contents 1 For your safety 7 1 1 Basic safety instructions T 1 2 Layout and meaning of warnings 7 1 3 User requirements 8 1 4 Intended use 8 1 5 EC declaration of conformity 8 2 About these Operating Instructions 9 2 1 Applicability 9 2 2 Target group of these Operating Instructions 9 2 3 Layout of operating instructions 9 2 4 Layout of references 9 3 Product description 10 3 1 Performance description 10 3 2 Scope of delivery 10 3 3 System requirements 11 3 4 Correctly interpreting information on the nameplate 11 4 Mounting and installation 12 4 1 Instructions on retrofitting 12 4 2 Mounting the terminal in the tractor cab 13 4 2 1 screwing on the GSM antenna 13 4 2 2 Terminal ports 14 4 3 SIM ca
32. TRACK Leader xiC xneeei7Ee8E8C4a0neF nn 3 Click on the TaskManager line The following screen will appear DIES Ye Fields 28 Farms B customers wip Farm equipment CB worker G Products E Me TM 02 00 60 TC 00 13 01 gt The TaskManager application has been started 8 1 4 Controls in the TaskManager application The TaskManager application is controlled using the rotary knob and the function keys In this chapter you will find an overview of all function icons that you may come across in the TaskManager application Controls 52 Copyright M ller Elektronik GmbH amp Co KG TaskManager application MUELLER ae lectronics Basics We CAN do it Switch to the GPS Receiver offset screen Configure the position of the GPS Receiver Remove the USB flash drive Will only appear if the folder Task data exists on the USB flash drive Prepare an empty USB flash drive for use with the TaskManager application without FarmPilot The Task data folder will be created on the USB flash drive Download a set of tasks from the FarmPilot portal Will only appear if you are connected to the FarmPilot portal Upload set of tasks to the FarmPilot portal Will only appear if you are connected to the FarmPilot portal Display the field in FIELD Nav The function icon is grey when the function has been deactivated Create
33. Water AVENTIS C Gay ME_ISO_SPRAYER Ce Worker 1 5 plant protection ets Filling Emptying a ME_ISO_SPRAYER volume counter 170 001 en gt Time counter 0 03 h The selected worker has been added and activated gt You will find the following information below the name of the worker For activated workers Date and time of activation For deactivated workers Date and time of deactivation gt You have selected a worker 80 Copyright Muller Elektronik GmbH amp Co KG TaskManager application Miemuetter aid lectronics Step 5 Using the TaskManager application during work We CAN do it 8 6 8 6 1 Procedure 8 6 2 Procedure 8 6 3 Step 5 Using the TaskManager application during work Entering a change of shift 1 Click on the following line on the Task data screen 2 End the active worker s shift gt The amount of time worked by the worker will no longer be recorded from now on 3 Add worker A list of names of available workers will appear lf the name of the desired worker does not appear the worker has not yet been created in the Farm Management Information System 4 Click on the desired worker on the list gt The worker will be added to the task gt The counters will begin to record the length of time spent working gt You have selected a worker Altering rates 1 Click on the following line on the Task data screen 2 Click on the
34. appear F4 Depending on the category a different struck through icon may appear Copyright M ller Elektronik GmbH amp Co KG 71 TaskManager application MUELLER Step 3 Entering and saving task data FEMUELLER We CAN do it Selecting a customer Procedure 1 Click on the following line and hold for two seconds gt A list of available customers will appear 2 Select customers from the list gt The name of the selected customer will appear on the Task data screen You have assigned the task to a customer Selecting a farm business Procedure 1 Click on the following line and hold for two seconds gt A list of available farms will appear The list only contain farms that belong to the selected customer 2 Click on the desired farm The selected farm will appear on the Task Data screen You have assigned the task to a farm Selecting a field Procedure 1 Click on the following line and hold for two seconds Ss gt A list of available fields will appear The list only contains fields that belong to the selected farm 2 Select the desired field gt The selected field will appear on the Task data screen gt You have assigned the task to a field Selecting a person in charge Procedure 1 Click on the following line and hold for two seconds gt A list of available people will appear 2 Select the desired person gt The name of the person will appe
35. application MUELLER en lectronics Basics We CAN do it The following screen will appear R Settings GPS Receiver offset i BRS offset X a cn gael Offset Y 0 cm gt y Operation mode ISO we 2 0 Select and click on the Operation mode line gt The mode will change with each click 3 Set the desired mode 4 Restart terminal gt The set mode will be activated after restart 8 1 6 Display layout in the TaskManager application The display of the COMFORT Terminal will always show two screens at the same time The Task data screen on the left All other screens on the right The following picture shows these two areas as well as additional information that can be found on the display DEE Fields F 88 Farms gt GB customers 2 yi Farm equipment CB worker Products TMV 02 00 60 TC 00 13 01 Display layout in the TaskManager application Copyright Muller Elektronik GmbH amp Co KG 55 TaskM licati askManager application MUELLER Basics lectronics We CAN do it 1 Task data screen Section with interchanging screens Permanent section 2 Counter section Function icons section You will always be shown the function icons that are associated with the currently active Screen 3 Cursor Information about the application version Determines which screen is currently active Selec
36. ar on the Task data screen You have assigned the task to a person Selecting rate and mix Icons You will see two icons on the screen Mix Name of the mix to be spread Product If the mix is composed of several products you can specify the individual products here 72 Copyright Muller Elektronik GmbH amp Co KG TaskManager application Miemuetter cea lectronics Step 3 Entering and saving task data We CAN do it To the right of each icon there are three input fields each of which you can select and click on with the cursor You can use the input fields to specify which mix you wish to spread in what quantity and composed of what products The application will not check whether the quantities of the individual products total the rate of the mix The following picture shows an overview of the input fields Zu N O o o0 Overview of the input fields 1 Rate 3 Unit of measurement 2 Product quantity 4 Product type Procedure 1 Click on the following line 2 Click on the first field next to the icon sg 3 Enter the desired rate 4 Click on the middle field next to the icon E 5 Select the unit of measurement 6 Click on the right hand field next to the icon 7 Select the product type 8 Enter the product quantity and the unit of measurement next to the icon 5 Anew line containing the icon 5 will appear 9 You can enter additional products next to
37. asks to the Farm Management Information System When you have finished processing a task or set of tasks you can export the completed tasks from the terminal for further processing and evaluation The following options are available to you Transfer tasks to the Farm Management Information System using a USB flash drive Send a set of tasks to the FarmPilot portal 8 8 1 Transferring tasks using a USB flash drive Procedure M You have completed all tasks M All tasks are marked red on the task list 1 Open the Master data screen G 2 WE Write task data to the USB flash drive 2 gt Wait until the icon disappears and the LED on the USB flash drive stops flashing 3 Remove the USB flash drive 4 Connect the USB flash drive to the farm computer Copyright M ller Elektronik GmbH amp Co KG 87 TaskManager application mer MEmueLLER Important files stored on the USB flash drive lectronics We CAN do it 5 Import and process data with the Farm Management Information System 8 8 2 Uploading a set of tasks to the FarmPilot portal Procedure M You have received the processed tasks via FarmPilot M You have completed all tasks All tasks are marked red on the task list 1 Open the Master data screen The following screen will appear Tasks X Fields i 28 Farms EB customers wip Farm equipment CB worker GF Products E Me TM 02 00 60 TC 00 13 01
38. ation Procedure M The GPS TILT Module terrain compensation is connected M The driver of the external LightBar is deactivated M The external LightBar is not connected 1 Measure the distance between the GPS Receiver and the ground surface 2 Switch on the terminal 3 Switch to the configuration screen of the terrain compensation S GPS gt Service Terrain compensation The following screen will appear GPS Receiver height 8 500 ft Null point calibration Angle 1 40 Copyright Muller Elektronik GmbH amp Co KG Configuring the terminal in the Service application AME mueLLER mn u er lectronics Screenshots We CAN do it 4 Enter the distance between the GPS Receiver and the ground surface in the line GPS Receiver height 5 Position the tractor on a ground surface that is known to be level 6 Click on the line Null point calibration The position of the terrain compensation on an even surface is being calibrated After calibration the angle 0 will appear in the line angle The angle displayed changes every time the tractor tilts 7 12 Screenshots A screenshot is a photo of the display If an error occurs when you are using the terminal Customer Services may ask you to capture a screenshot A screenshot can be emailed to Customer Services Email address service mueller elektronik de sentto the FarmPilot portal provided you have activated the FarmPilot po
39. ation System to the terminal lectronics We CAN do it Creating a Task data folder on the USB flash drive You must create a Task data folder in the following instances f you use the TaskManager without the FarmPilot portal f you wish to export the machine settings to the Farm Management Information System Procedure 1 Insert an empty USB flash drive into the terminal 2 Open the TaskManager application ED TaskManager The following screen will appear DIES X Fields i 28 Farms B customers wip Farm equipment CB worker GF Products fo E Me TM 02 00 60 TC 00 13 01 G gt f the following function icon appears on this screen the folder has already been created as gt The Task data folder is being created on the USB flash drive A function icon will appear on the Master data screen RR 8 2 2 Transferring data via the FarmPilot portal You will receive data from the portal if they are sent by a dispatcher The dispatcher will always send the data as sets of tasks that consist of one or more tasks Procedure You will receive the set of tasks from the dispatcher as follows M You have opened the TaskManager application VI You have inserted a USB flash drive into the terminal VI NOTE The USB flash drive must not contain a folder named TASK DATA However if the folder does exist you must save gt 87 the exi
40. attachment point of the attached and trailer equipment and the GPS Receiver 2 Enter the distance measured as parameter Offset X 3 Measure the distance between the longitudinal axis of the machine and the GPS Receiver 4 Enter the distance measured as parameter Offset Y Procedure Thus you can calculate the distances for self propelled machines with an ISOBUS jobcomputer M The jobcomputer of the farm equipment in use is connected to the terminal M In the jobcomputer the geometry of the farm equipment is configured 1 Enter 0 cm as parameter Offset X 2 Measure the distance between the longitudinal axis of the machine and the GPS Receiver 3 Enter the distance measured as parameter Offset Y For machines not fitted with a jobcomputer When you connect an agricultural device without an ISOBUS job computer to the tractor you need to enter the position of the GPS receiver in the TRACK Leader application To do so you have to create a machine profile Copyright Muller Elektronik GmbH amp Co KG 19 Mounting and installation i MUELLER GPS Receiver l E MUELLER We CAN do it You can read how to do this in the operating instructions to TRACK Leader All data on the GPS Receiver offset screen will be ignored 20 Copyright M ller Elektronik GmbH amp Co KG Basic control principles MME mueLLER nn lectronics Getting to grips with the controls We CAN do it 5 Basic control principles 5 1 Getting
41. ay ME_ISO_SPRAYER worker 5 fertilization ets Filling Emptying we ME_ISO_SPRAYER fertilization 2 00 Field 2 volume counter 0 00 on Surface counter 0 00 ha Mueller 2 Distance counter 0 00 km 2 00 Field 2 Time counter 0 00 h fem Worker The task must be marked with the following icon A Task started Split task The following notification will appear Split task 6 Confirm gt The following screen will appear Ry TSk131 B fertilization 2 00 Field 2 B fertilization 2 00 Field 2 lla fertilization 2 00 Field 2 W Mueller 82 00 Field 2 fam Worker ug 268 00 I ha AHL 28 66917572ter Gay ME_ISO_SPRAYER 2 worker 5 fertilization ets Filling Emptying bad ME_ISO_SPRAYER fertilization 2 00 Field 2 Yolume counter 0 00 NASE Surface counter 0 00 ha W Mueller 2 Distance counter 0 00 km ax 2 00 Field 2 Time counter 0 00 h Worker A new task will appear on the Task list screen The task is marked with an asterisk This task is the unprocessed portion of the original task It contains all the data from the original task In particular the field boundaries and obstacles from SECTION Control gt You have split the task and created a copy You now have the following options You can alter the rates and products for this task gt 72 70 Copyright M ller Elektronik GmbH amp Co KG TaskManager application
42. bcomputer diagnostics 42 Sending diagnostic data to the portal 43 7 13 2 CAN Trace settings 43 7 14 Activating an external LightBar 44 7 15 Camera 45 7 15 1 Activating a camera 45 7 15 2 Operating the camera 45 7 16 Configuring FarmPilot 46 7 16 1 Activating FarmPilot 47 7 16 2 Configuring the connection with FarmPilot 47 7 16 3 Configuring the GPRS connection manually 48 8 TaskManager application 51 8 1 Basics 51 8 1 1 About TaskManager 51 8 1 2 USB flash drive 51 8 1 3 Starting the TaskManager application 51 8 1 4 Controls in the TaskManager application 52 8 1 5 Setting up the operation mode for the TaskManager application 54 8 1 6 Display layout in the TaskManager application 55 Switching between screens 56 Master data screen 56 Task list screen 57 Task data screen 58 8 1 7 Exporting machine settings for the Farm Management Information System 59 4 Copyright M ller Elektronik GmbH amp Co KG MUELL ER Contents lectronics We CAN do it 8 2 Step 1 Transferring data from the Farm Management Information System to the terminal 61 8 2 1 Transferring data using a USB flash drive 61 Creating a Task data folder on the USB flash drive 62 8 2 2 Transferring data via the FarmPilot portal 62 8 3 Step 2 Selecting a task to process 63 8 3 1 Creating a new task on the terminal 63 Creating a new task 63 Copying a task 65 8 3 2 Adopting an existing task 66 Resuming a task 67 Splitting an order that has already been starte
43. captured in the location you specified as the Storage location The USB flash drive saves the screenshots in the folder ScreenCopy 7 13 Activating the Diagnostics function To activate the Diagnostics function you must first activate its driver Procedure 1 Switch to the Driver settings screen gt Service Driver settings The following screen will appear re S t Diagnostics t FarmPilot LightBar t Camera 2 Click on Diagnostics 3 Click on the DiagnosticsServices driver gt Next to the driver the icon will appear 4 Restart terminal The following function icon will appear on the start screen of the Service application LE gt You have activated the Diagnostics function 7 13 1 Jobcomputer diagnostics The screen Jobcomputer diagnosis contains a variety of information that is primarily important to Customer Services Customer Services can use this screen to determine which versions of the hardware and software are installed on your terminal This will speed up the diagnostic process if errors arise 42 Copyright Muller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application lectronics or We CAN do it Activating the Diagnostics function Sending diagnostic data to the portal Customer Services may ask you to send diagnostic data to the portal This allows Customer Services to gather detailed
44. d 68 8 4 Step 3 Entering and saving task data 71 8 4 1 Entering task data 71 Selecting a customer 72 Selecting a farm business 72 Selecting a field 72 Selecting a person in charge 72 Selecting rate and mix 72 Measure 73 8 4 2 Saving task data 74 8 5 Step 4 Starting a task 75 8 5 1 Selecting the machine 76 8 5 2 Selecting a worker 79 8 6 Step 5 Using the TaskManager application during work 81 8 6 1 Entering a change of shift 81 8 6 2 Altering rates 81 8 6 3 Selecting the task processing phase 81 8 6 4 Evaluating counters 82 8 6 5 Displaying the counters of a machine 83 8 6 6 Documenting filling and emptying 83 8 6 7 Exiting the TaskManager application 85 8 7 Step 6 Stopping work 85 8 7 1 Stopping a task 85 8 7 2 Pausing a task 85 8 8 Step 7 Transferring completed tasks to the Farm Management Information System 87 8 8 1 Transferring tasks using a USB flash drive 87 8 8 2 Uploading a set of tasks to the FarmPilot portal 88 8 9 Important files stored on the USB flash drive 88 9 Maintenance and servicing 90 9 1 Servicing and cleaning the terminal 90 9 2 Disposing of the unit 90 9 3 Checking the software version 90 9 4 Technical specifications 90 9 4 1 Technical specifications of the terminal 90 9 4 2 Pin assignment of port A 91 9 4 3 Pin assignment of port B 92 Copyright M ller Elektronik GmbH amp Co KG 5 Contents MUELLER lectronics we CAN do it 9 4 4 Pin assignment of port C 93 9 45 Pin assignment of cam
45. do it The following screen will appear T Country Germany Provider D2 Vodafone Apn web vodafone de Dnsl 1397 20 125 2 Set GPRS connection parameters 50 Copyright M ller Elektronik GmbH amp Co KG MUELLER TaskManager application lectronics nn We CAN do it 8 TaskManager application 8 1 Basics 8 1 1 About TaskManager laskManager is an application from Muller Elektronik working as the interface between an agricultural device and Farm Management Information System on the terminals With TaskManager you can open all orders previously planned in the Farm Management Information System on the terminal All information contained in the order will be transferred by TaskManager to specialized applications of the terminal This means that each application is doing exactly what it can do best The position of the field is transferred to FIELD Nav It can therefore navigate the terminal directly to the field The prescription map field border and other information about any work important for sub areas Stored in the order are transferred to TRACK Leader The field can be therefore processed TaskManager documents work duration attending persons machines and operating means After work completion TaskManager saves all work results on the USB flash drive so that you can open them again in your Farm Management Information System The version described here supports the following
46. drive when using the FarmPilot portal This requires that the USB flash drive be inserted into the terminal Copyright Muller Elektronik GmbH amp Co KG 89 Maintenance and servicin 3 MUELLER Servicing and cleaning the terminal E MUELLER We CAN do it 9 Maintenance and servicing NOTICE This product does not contain any components which require maintenance or repair Never unscrew the casing 9 1 Servicing and cleaning the terminal Press the keys with your fingertips Avoid using your finger nails Only clean the product with a soft damp cloth Only use clear water or glass cleaner 9 2 Disposing of the unit When it has reached the end of its service life please dispose of this product as electronic scrap in accordance with applicable EU legislation aay 9 3 Checking the software version Procedure 1 Open the Service application Service 2 The following screen will appear R File management Driver settings Sb Plugin settings 7A License management ME 3 The software version can be found below the ME logo 9 4 Technical specifications 9 4 1 Technical specifications of the terminal Operating voltage 10 30 V Operating temperature 20 70 C 90 Copyright M ller Elektronik GmbH amp Co KG Maintenance and servicin MME mueLLER 3 lectronics Technical specifications We CAN do it Power input At terminal 30322527 Typically 0 9
47. dule is configured You can order the terrain compensation from Muller Elektronik with the following item number 30302495 Controls Function icon Reset the configuration of the DGPS Receiver to default values Display DGPS connection status Procedure You can configure the parameter as follows VI The DGPS Receiver A100 from Muller Elektronik is connected and activated M The driver of the external LightBar LightBar_ME is deactivated Otherwise the DGPS Receiver cannot be configured M The external LightBar is not connected 1 Switch to the GPS screen Eas Service Copyright Muller Elektronik GmbH amp Co KG 39 We CAN do it Configuring the terminal in the Service application iguring inal i ice applicati MUELLER T Configuring the GPS TILT Module terrain compensation SS MUSLLER The following screen will appear oaths y Eaua rate gt Satellite 1 gt Satellite 2 i Steering lt Correction signal ME GPS v02 01 07 a 2 Click on the desired parameter gt A selection list will appear 3 Click on the desired value gt Next to the value the icon G will appear 4 Back gt For some parameters is it necessary to restart the terminal In these cases the following notification will appear Settings will be adopted after restart gt You have configured the DGPS Receiver 7 11 Configuring the GPS TILT Module terrain compens
48. e list i 4 3 Press and hold for 3 seconds gt Machine will be activated 78 Copyright Muller Elektronik GmbH amp Co KG MUELLER lectronics TaskManager application Step 4 Starting a task 8 9 2 Controls Icons Procedure 1 Selecting a worker This step requires that you select the workers who will process the task You can add any number of workers The terminal records the length of time worked by the workers you added _ Add worker grey asterisk next to the image of the worker _ End worker s shift red x next to the image of the worker Workers can be activated or deactivated The terminal will calculate the amount of time worked by the workers you activated The icon preceding the name of the worker indicates whether the worker is activated or deactivated Worker is deactivated red background Worker is activated green background noicon No icon will precede the name of the worker assigned to the task You can activate a worker as follows 1 Click on the following line on the Task data screen The following screen will appear a En TSk 1 Worker 1 B plant protection 2 00 Field 2 01 03 2011 00 00 00 W Mueller K 2 00 Field 2 fem Worker 1 4g 202 00 I ha Mix Water AVENTIS C Gop ME_ISO_SPRAYER Ce worker 1 plant protection ety Filling Emptying sd ME_ISO_SPRAYER volume counter 117 001 Su
49. ed to enter any task data for this task 4 Start task gt 75 The following screen will appear af ME_ECO_Spritze ere CP Tasks B 2011 02 24 11 24 01 X Fields a 28 Farms ia B customers S yp Farm equipment a CB worker ag GF Products Fa Ko S gt ets Filling Emptying WA ME_ECO_Spritze Me TM 02 00 60 TC 00 13 01 5 Wait several minutes until the counters appear The following screen will appear af ere CP Tasks B 2011 02 24 11 24 01 X Fields a 28 Farms M EB customers S wip Farm equipment a CB worker ag GF Products Say ME_ECO_Spritze ets Filling Emptying ie WZ ME_ECO_Spritze Yolume counter 0 00 Surface counter 0 00 ha Distance counter 0 00 km TM 02 00 60 TC 00 13 01 Time counter 0 00 h Copyright M ller Elektronik GmbH amp Co KG TaskM licati MUELLER askManager application lectronics Step 1 Transferring data from the Farm Management Information System to the terminal we CAN do it 6 ES Stop task 7 D Switch to the Master data screen Save the data on the USB flash drive gt The machine data are saved to the Taskdata xml file located in the Task data folder on the USB flash drive 9 Wait until the data have been written and read G gt The function icon will be hidden 10 Remove the USB
50. er TRACK Leader TOP automatic steering Additional module for TRACK Leader FIELD Nav this is the first navigation software that contains all navigable paths takes movement restrictions into account and leads directly to the field or other agricultural destination 3 2 Scope of delivery The following items are included in delivery Terminal Installation and Operating Instructions Bracket for mounting the terminal USB flash drive 10 Copyright Muller Elektronik GmbH amp Co KG Product description MUELLER P l E MUELLER System requirements We CAN do it 3 3 System requirements The following requirements must be met for the tractor to be used in conjunction with the terminal The tractor must be ISOBUS capable If your tractor is not ISOBUS capable you can upgrade it Our staff will be glad to advise you on selecting compatible components Requirements for the Farm Management Information System In order to use the data from the TaskManager application with the Farm Management Information system The Farm Management Information System must be ISO XML capable System requirements for using the FarmPilot portal To use the FarmPilot portal you will require a terminal with a built in GSM modem The following terminals are currently equipped with a modem BASIC Terminal GSM item no 30322512 BASIC Terminal TOP GSM item no 30322522 COMFORT Terminal GSM item no 30322527 If you
51. era ports 1 and 2 94 10 Notes 95 Copyright Muller Elektronik GmbH amp Co KG For your safet MUELLER a i E MUELLER Basic safety instructions We CAN do it 1 For your safety 1 1 Basic safety instructions Please read the following safety instructions carefully before operating the product for the first time Before maintenance or repair to the tractor always disconnect the connection between the tractor and the terminal Before charging the tractor battery always disconnect the connection between the tractor and the terminal Before welding to the tractor or an attached device always disconnect the power supply to the terminal Do not make any unauthorized modifications to the product Unauthorized modifications or use may impair safety and reduce the service life or operability of the unit Modifications are considered unauthorized if they are not described in the product documentation Follow all recognised safety industrial and medical rules as well as all road traffic laws 1 2 Layout and meaning of warnings All safety instructions found in these Operating Instructions are composed in accordance with the following pattern This signal word identifies medium risk hazards which could potentially cause death or serious bodily injury if not avoided This signal word identifies low risk hazards which could potentially cause minor or moderate bodily injury or damage to property if not avoided
52. flash drive from the terminal gt You have transferred the machine parameters to the USB flash drive According to whether you wish to export machine data to create a new machine in the Farm Management Information System or update the parameters of an existing machine a different procedure applies in the Farm Management Information System Follow the manual for your Farm Management Information System If you create more than one entry for a machine in the Farm Management Information System this can later lead to errors in the TaskManager o Only create one entry per machine in the Farm Management Information System 8 2 Step 1 Transferring data from the Farm Management Information System to the terminal You can transfer the data from the Farm Management Information System to the terminal in the following ways using a USB flash drive via the FarmPilot portal 8 2 1 Transferring data using a USB flash drive Procedure M You have created the Task data folder on the USB flash drive M The Task data folder contains the file Taskdata xml 1 Start the TaskManager application TaskManager 2 Insert the USB flash drive into the terminal The following notification will appear Copying task data The task processed most recently will be started automatically Copyright Muller Elektronik GmbH amp Co KG 61 TaskManager application Miemueiter Step 1 Transferring data from the Farm Management Inform
53. functions Creating tasks on the terminal Viewing and processing tasks that have been planned using the Farm Management Information system Transferring prescription maps from an order to TRACK Leader Delivering required values to ISOBUS job computers Documenting how the work has been done The type of documented data depends on the type of the ISOBUS job computer Saving work results for further evaluation in PC software Recording complete task data Exchanging task data between the FarmPilot portal and the TaskManager 8 1 2 USB flash drive The USB flash drive has two jobs tis used to move data between the Farm Management Information System and the terminal tis the external storage during work The USB flash drive must always be connected during work See also Step 1 Transferring data from the Farm Management Information System to the terminal gt 61 Step 7 Transferring completed tasks to the Farm Management Information System gt 87 8 1 3 Starting the TaskManager application Procedure 1 Insert an empty USB flash drive into the terminal Copyright Muller Elektronik GmbH amp Co KG 51 TaskM licati askManager application MUELLER Basics lectronics We CAN do it 2 Open the Selection menu application gt The following screen will appear Service 0x26 xneee10EEeC490nGF sS7h2de x87 xnesCcesEeeC 490004 TaskManager xF7 6xheess2888C48000F
54. he casing 4 4 GPS Receiver The GPS Receiver gathers and transmits information about the position of the machine to the connected terminal Technical requirements for using the DGPS Receiver Operating voltage Supply voltage of the terminal 1 5 V Current consumption Maximum of 200 mA at 70 C without any additional load from other appliances the current consumption of the multifunctional grip and LightBar have already been taken into account in this specification GPS standard NMEA 0183 Refresh rates and signals 5 Hz GPGGA GPVTG 1 Hz GPGSA GPZDA 16 Copyright M ller Elektronik GmbH amp Co KG MUELLER Mounting and installation lectronics GPS Receiver We CAN do it r 4 4 1 Connecting the GPS Receiver to the terminal Damage to the equipment caused by short circuit Pin 4 of port C is live The voltage depends on the operating voltage of the terminal and is used to supply the DGPS Receiver A100 from M ller Elektronik Other GPS Receivers may suffer damage if connected to this port Before connecting a different GPS Receiver Check what voltage the terminal is connected to 12 V or 24 V Check the pin assignment of the GPS Receiver Check the allowable voltage for the GPS Receiver Compare the terminal voltage to the allowable voltage for the GPS Receiver Compare the pin assignment Only connect the GPS Receiver to the terminal if the voltage range and pin assignment of both de
55. hed in parallel with pin 4 by port B Total loading is 600mA When switched on the terminal routes current to the farm equipment that is connected via the RS232 connector The voltage of the RS232 connector is dependent on the operating voltage of the terminal When connected to a 12 V battery the terminal will transfer approx 11 3 V to the connected equipment Copyright Muller Elektronik GmbH amp Co KG 93 Maintenance and servicing MUELLER Technical specifications l fEMUELLER We CAN do it When connected to a 24 V battery the terminal will transfer approx 23 3 V to the connected equipment The use of a GPS Receiver only requires the signals RxD and TxD as well as GND 9 4 5 Pin assignment of camera ports 1 and 2 Ports 1 and 2 are used to connect an analogue camera The pin assignment is identical for both ports Ports 1 and 2 are 5 pin A encoded M12 sockets Please refer to the following table for the pin assignment QO O 4 0 QO JQ O Pin assignment of the socket in Pin assignment of the connector the terminal C Pin is exclusively intended for use by ME do not connect anything Pin is exclusively intended for use by ME do not connect anything Video signal 94 Copyright M ller Elektronik GmbH amp Co KG MUELLER mors lectronics We CAN do it 10 Notes Copyright M ller Elektronik GmbH amp Co KG 95
56. information about your terminal and therefore examine it more thoroughly Procedure M You have activated the Diagnostics function M You have activated the FarmPilot portal 1 Switch to the Jobcomputer diagnosis screen gt Service Jobcomputer Diagnostics Send diagnostic data The following notification will appear DeviceidentData transfer The data are being uploaded to the portal 3 Wait until the Sending DeviceldentData notification disappears gt The data have been uploaded to the portal 4 Ifthe process is taking too long you can cancel the data transfer 5 Cancel data transfer 7 13 2 CAN Trace settings CAN Trace is a function that logs the data exchange between the terminal and the connected jobcomputers Customer Services can use the logged data for diagnostic purposes should any errors arise in the system If an error occurs when using the terminal Customer Services may ask you to activate the CAN Trace function Only activate this function if prompted to do so by Customer Services Procedure 1 Switch to the CAN Trace settings screen Service oa LE CAN Trace settings Click on Duration min 2 Set the duration Specify for how long communication should be logged after the terminal has been restarted Communication can be logged for a duration of one to five minutes 3 Click on Storage location 4 Select the storage location 5 Selec
57. ions on retrofitting Instructions on how to retrofit electrical and electronic farm equipment and or components Agricultural equipment used today features electronic components and parts whose function can be affected by other farm equipment which emits electromagnetic waves Such effects could lead to personnel being put in danger if the following safety instructions are not adhered to Selecting components When selecting components make sure first of all that the retrofitted electrical and electronic components comply with the current version of the EMC Directive 2004 108 EC and carry the CE marking User responsibility When retrofitting a machine with electrical and electronic farm equipment and or components connected to the vehicle s electrical system it is your own responsibility to check whether the installation causes interference with the vehicle s electronic system or other components This applies in particular to the electronic control of EHR front linkage take off shafts engine gear Additional requirements The following requirements must be met in order to retrofit mobile communication systems e g radio phone All farm equipment must be approved and installed in accordance with the regulations applicable in the respective country e g in Germany the Federal Approvals Office for Telecommunications BZT The equipment must be installed as a fixed installation The operation of portable o
58. it The following screen will appear OP Wee ener TRACK Leader FIELD Nav a 2 Click on the desired plugin The icon preceding the name of the plugin indicates whether the plugin is activated or deactivated 3 Exit screen The following notification will appear Changes will be adopted after restart a 4 Confirm 5 Restart terminal gt All activated plugins will appear in the selection menu 7 7 Activating licenses for full versions of the software Several applications are pre installed on the terminal which you can use for trial purposes for up to 50 hours gt 10 After this time has elapsed they will be automatically deactivated The amount of free usage time remaining is shown in brackets next to the name of the application To activate a license you will require an activation number which you will receive on purchasing an application from Muller Elektronik If you request the activation number by phone or by email you will be required to give our staff the following information Code Found under the name of the application on the License management screen Serial number of the terminal Found on the nameplate on the reverse of the terminal Item number of the terminal Found on the nameplate on the reverse of the terminal Procedure The activation number is entered as follows 1 Switch to the License management screen 9 7 Service License manage
59. ith task data gt 71 You can start the task gt 75 You can save the task gt 74 Copying a task You will not always have to create a new task In most cases it is advisable to copy an existing task and save the copy as a new task The copy of the task contains all the field boundaries and application cards of the original task but can be processed like a new task 1 Switch to the Master data screen The following screen will appear Procedure mt 2 Click on the Tasks line Copyright Muller Elektronik GmbH amp Co KG af DIES X Fields 28 Farms B customers wip Farm equipment CB worker GF Products ME TM 02 00 60 TC 00 13 01 65 TaskManager application Step 2 Selecting a task to process The following screen will appear mt P a fertilization 2 00 Field 2 amp a fem Worker MUELLER lectronics We CAN do it rman fertilization 2 00 Field 2 Mueller 2 00 Field 2 3 Select a task that has the most similarities to the task you wish to create The task must not be Started Create a copy of an existing task gt The following notification will appear Copy task 5 Confirm The following screen will appear mt we gt The new task will be added to the list a You have created a new task You now have the following options
60. les stored on the USB flash drive We CAN do it When using the FarmPilot portal the file will automatically be created in the folder TaskData_work When working without the FarmPilot portal you must copy the file from the hard drive to the folder TASK DATA on the USB flash drive The Taskdata xml file must not be larger than 2 MB Files that are too large may cause problems during data transfer and slow down the terminal considerably GRD number bin A file containing the application cards for a field If you wish to use the task manager in combination with application cards you must transfer this file to the terminal as well Important folders TaskData A folder containing all tasks of a set of tasks that are currently being processed This folder will only be required if you use the TaskManager application without FarmPilot Also read the chapter Creating a Task data folder on the USB flash drive gt 62 TaskData_work A folder containing all tasks of a set of tasks that are currently being processed This folder will be created automatically when the USB flash drive is inserted into the terminal It will then replace the task data folder until the task data are written to the USB flash drive Thus until the E function key is pressed TaskData number Backup copies of the tasks sent to the FarmPilot portal will be created in this folder The folder will automatically be created on the USB flash
61. letion of this portion Uncompleted portion of the task will be displayed on the list as a new task You can continue processing this task The task contains all the field boundaries and field data from the original task Procedure 1 Switch to the Master data screen 68 Copyright Muller Elektronik GmbH amp Co KG MUELLER TaskManager application lectronics Step 2 Selecting a task to process We CAN do it The following screen will appear BES X Fields 28 Farms B customers wip Farm equipment CB worker G Products E Me TM 02 00 60 TC 00 13 01 2 Click on the Tasks line The following screen will appear Pfertilization 2 00 Field 2 mt we fertilization 2 00 Field 2 W Mueller amp 2 00 Field 2 fem Worker gt gt The list contains an overview of the tasks stored on the USB flash drive 3 Start the desired task You can only copy tasks that have already been started 4 Return to the Task list screen Copyright M ller Elektronik GmbH amp Co KG 69 TaskManager application on IME Muciter Step 2 Selecting a task to process lectronics We CAN do it The following screen will appear n fa TSK131 ffertilization 2 00 Field 2 B fertilization 2 00 Field 2 W Mueller GY 2 00 Field 2 fem Worker 4g 268 00 I ha AHL 28 66917572ter G
62. ll learn how to adjust the brightness of the display for day or night mode Procedure 1 Open the Service application gt Service Copyright M ller Elektronik GmbH amp Co KG 31 We CAN do it Configuring the terminal in the Servi licati M onfiguring the terminal in the Service application MUELLER T Configuring the basic display settings lectronics gt The ne Following screen will appear x Display settings J File management Fr Driver settings h Plugin settings 7 License management ME Terminal Y 03 90 00 2 Change the operating mode Depending on which operating mode is currently active you can use one of the function icons EGT J s Eo Activate day mode t Zu 13 Activate night mode gt The brightness of the display will be adjusted immediately 7 5 Configuring the basic display settings The basic display settings can be adjusted on the Display settings screen Procedure 1 Switch to the Display settings screen ED Service Display settings The following screen will appear R J Brightness Volume 1 Date time l Measurement units Metric Keyboard brightness 50 a a 2 Change the desired parameter Brightness Adjusting brightness for day mode Night Adjusting brightness for night mode Night mode Switching night mode on and off 0 day mode is activated 32 Copyright
63. ment 34 Copyright M ller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application lectronics Deleting files from the USB flash drive We CAN do it The following screen will appear A Wes veneer TRACK Leader II 50 00 BMJZMZKJTLLIJACEFR TRACK Leader TOP 50 00 BMJZMZKJTLLIJACFXY SECTION Control 50 00 BMJZMZKJTLLIJACRRU 2 Click on the desired application The following screen will appear wt Name SECTION Control Code BMIZMZKIJTLLIJACRRU Key 0000000000 Status deactivated Remaining 3 Enter the activation number in the Key field You will receive the activation number on purchasing a software licence 4 Confirm gt The following icon will appear next to the application on the License management screen gt The application is activated You can use the application without any restrictions 7 8 Deleting files from the USB flash drive NOTICE Potential loss of data Deleted files cannot be retrieved o Think very carefully about which file you wish to delete On the File management screen you can delete files from the USB flash drive The File management screen only displays files that are stored in either of the following two folders on the USB flash drive Screencopy contains all screenshots you have created Taskdata contains all task data for the TaskManager applicatio
64. n Procedure 1 Switch to the File management screen Service File management Copyright Muller Elektronik GmbH amp Co KG 35 Configuring the terminal in the Servi licati onfiguring the terminal in the Service application MUELLER T Deleting pools l E MVELLER We CAN do it The following screen will appear tr kzl Pools 2 Click on USB gt The Screencopy and Taskdata folders will appear f these folders fail to appear it is because you did not create them on the USB flash drive 3 Click on the desired folder gt The contents of the folder will be displayed A folder may either contain files or further folders If nothing is displayed the folder is empty 4 Select the files to be deleted E 5 Delete file red gt Deleting file 7 9 Deleting pools You can delete the pools to speed up the terminal s operation Pools are the intermediate storage for the terminal Pools are used to temporarily store graphics or text Over time the pools will become too large and slow down the operation of the terminal After updating the software of a connected jobcomputer fthe terminal operates more slowly than usual When asked to do so by Customer Services When to delete Procedure 1 Switch to the File management screen gt Service File management gt The following screen will appear t kz Pools 2 Click on Pools The name
65. n this screen installed software 7 1 Controls in the Service application The Service application is controlled using the rotary knob and the function keys Controls Some of the function icons explained here will only appear if a specific function is activated This limits the information shown on the display to just the information that you need for your work Function icon Meaning Appears only if Scroll There is one more page with function icons Back 4 P Activate day mode er Activate night mode x File cannot be deleted grey Selected object cannot be deleted Copyright M ller Elektronik GmbH amp Co KG 29 Configuring the terminal in the Service application a MME mueLLER T Icons in the Service application lectronics We CAN do it Function icon Meaning Appears only if 7 2 Icons 1 3 Procedure 30 Delete file red Selected object can be deleted bd Configure GPS Receiver GPS Receiver is activated a wa Configure FarmPilot FarmPilot portal is activated Wu Open the Diagnostics screen Diagnostics is activated n Retrieve default values By o Display DGPS connection status Icons in the Service application You will find the following icons in the Service application laf Function is activated Function is deactivated Changing the language When you switch on the terminal for the first time
66. nformation The main display shows the application from an application currently running function icons and the information you need to control the application that is currently running Copyright Muller Elektronik GmbH amp Co KG 27 Openi lications in the selection men pening applicati i i u MUELLER Segmentation of the display ME MuE ER onics We CAN do it In the selection menu you can see which applications can be run with the split display Controls Function icon Function Switch applications in the header section Swap applications between the header section and the main section of the display 28 Copyright Muller Elektronik GmbH amp Co KG Configuring the terminal in the Service application Miemueiter oe en lectronics Controls in the Service application We CAN do it 7 Configuring the terminal in the Service application In the Service application you can configure the terminal and activate the connected farm equipment Once you have launched the Service application you will be shown the following screen 3 Display settings n 4 File management Mr Driver settings S Plugin settings 7A License management Start screen of the Service application 1 Main section 3 Cursor Screen contents Selects a line that can be clicked on with the rotary knob 2 Version number Function icons section Name of the terminal and version of the Icons that can be pressed o
67. on key this means that this function key has no function at present 5 4 Restarting the terminal When restarting the terminal you must give the connected jobcomputers enough time to restart as well For this reason always wait approx 30 seconds after switching off the terminal before switching the terminal back on Procedure 1 Switch off the terminal 2 Wait 30 seconds until the jobcomputers have also been switched off 3 Switch on the terminal 24 Copyright Muller Elektronik GmbH amp Co KG MUELLER Basic control principles lectronics We CAN do it Inputting data 5 5 Inputting data All data must be entered on the data input screen BBCDEFGHIJKLMNOP OR SITUVWHY Zapedecic Avi KAM Op 2 hilly 324 d OK Data input screen Controls Below the characters you will find 5 icons which will assist you when entering the data Delete characters Move cursor to the left Move cursor to the right Confirm and finish input No function SQ Procedure This is how you enter the data VI The data input screen has been opened 1 Select the desired character 2 Click on the selected character 3 When all characters have been entered select the OK symbol with the rotary button and click gt The input will be applied Copyright M ller Elektronik GmbH amp Co KG 25 Openi lications in the selecti pening applications in the selection menu MUELLER lectronics We
68. pened the Service application 8 Configuring the terminal in the Service application gt 29 5 3 Using the function keys Whenever you use the function keys you will activate the function depicted on the adjacent function icon Copyright Muller Elektronik GmbH amp Co KG 23 Basic control principles i f MUELLER Restarting the terminal l E MUELLER We CAN do it Danger of pressing the function keys without care When pressing function keys components of the connected machine can be moved or activated As a result people can be injured and property damaged Before pressing a function key Make sure you know what will happen when you press the function key Consult the Operating Instructions of the connected machine or of the agricultural equipment to establish what dangers could arise from pressing that key Fulfill all the measures described in the machine s Operating Instructions in order to avoid danger Only press the function key when you are sure that no danger is posed to people or property When you press a function key the function operation depicted on the function icon will be performed Using the function keys Function icon Function key Depiction of an available function Performs the function depicted on the function icon Example When you press the function key 2 the function depicted on the function icon will be activated If not function icon appears next to a functi
69. r i Gy ME_ISO_SPRAYER worker 5 fertilization ets Filling Emptying a ME_ISO_SPRAYER gt You can identify whether you are entering the filled capacity or the emptied capacity by the icon in the upper left hand corner 4 The screen consists of three columns in which you can enter data In the left hand column Enter capacity In the middle column Enter the unit litres t tonnes In the right hand column Select from a list the product to be filled or emptied 84 Copyright Muller Elektronik GmbH amp Co KG MUELLER TaskManager application Step 6 Stopping work We CAN do it 5 Exit screen 6 The following notification will appear Save changes 7 Click Yes to confirm gt The Task data screen will appear 8 6 7 Exiting the TaskManager application You can exit the TaskManager application at any time This will neither finish nor cancel the tasks Procedure 1 CD Open the Selection menu application The selection menu will appear 2 Start the desired application 8 7 Step 6 Stopping work You can stop a task at any time You must decide yourself whether this task has been fully processed or must be processed further If you stop the work you must decide what should happen to the task Depending on whether the task was fully processed or must be processed further you have the following options Stop task Pause task
70. r l E MUELLER We CAN do it gt The installed drivers will appear EEE Disabled GPS_PSRCAN GPS_A100 t Diagnostics t FarmPilot t LightBar amp Camera gt Next to the active driver the icon will appear gt The driver GPS A100 for the DGPS Receiver A100 from Muller Elektronik comes activated as standard 4 Select the line containing the correct antenna driver GPS_A100 if the DGPS Receiver was connected directly to the terminal port C GPS_PSRCAN if the GPS Receiver was connected via the CAN interface i e to a jobcomputer 5 Click on the selected line lt gt Next to the driver the icon i will appear 6 Restart terminal gt GPS Receiver is activated gt The following function icon will be displayed on the start screen of the Service application eal ops gt gt You have activated the GPS Receiver 7 10 2 Configuring the DGPS Receiver A100 The DGPS Receiver A100 is delivered ready configured However you can change the configuration In this chapter you will learn how to do this Parameters You can configure the following parameters in the process Baud rate Setting for the speed at which the terminal sends data to the DGPS Receiver The parameter sets the baud rate for the terminal The default baud rate is 19200 This baud rate is suitable for the DGPS Receiver A100 Satellite 1 and Satellite 2 Only required with the correction signal WA
71. r mobile farm equipment in the interior of the vehicle is only permitted via a connection to a permanently installed exterior antenna The transmitting part must be spatially separated from the vehicle s electronic system When attaching the antenna pay attention to proper installation including a sound ground connection between the antenna and the vehicle s ground wire For information on wiring and installation as well as the maximum allowable current consumption please also refer to the installation guide provided by the machine manufacturer 12 Copyright Muller Elektronik GmbH amp Co KG Mounting and installation Miemuetter lectronics Mounting the terminal in the tractor cab We CAN do it 4 2 Mounting the terminal in the tractor cab Electromagnetic interference The operation of the terminal may be impaired by electromagnetic waves emitted by other farm equipment Mount the terminal at least 1 m away from the radio antenna or from a radio device Procedure 1 Screw the bracket to the terminal 2 Mount the terminal with the bracket installed inside the tractor cab For instance you can use the ME base console for this purpose The base console is not included in the terminal delivery It belongs to the delivery scope of ISOBUS basic equipment Base console 4 2 1 Screwing on the GSM antenna The GSM antenna transmits information to the FarmPilot portal via a mobile phone network Proced
72. r the GPS Receiver is to the left or right of the tractor s longitudinal axis and whether it is positioned before or after the attachment point Procedure 1 Switch to the Settings screen gt TaskManager The following screen will appear R Settings FE GPS Receiver offset i BRS Offset N con a Offset Y 0 cm y Operation mode 2 Measuring the position of the GPS Receiver You will find out how to do this in the following subchapters 3 Enter the distances measured in the fields Offset X and Offset Y For machines fitted with an ISO jobcomputer On the following illustration distances are marked which must be measured for each different machine 18 Copyright M ller Elektronik GmbH amp Co KG Mounting and installation MME mueLLER i lectronics GPS Receiver We CAN do it GPS Receiver offset with ISOBUS machines Attachment point for attached and trailer GPS Receiver equipment 1 Attached and trailer equipment 2 Self propelled machines y Distance between the longitudinal axis and the x Distance for Offset X GPS Receiver for Offset Y Procedure Thus you can calculate the distances for machines with attached and trailer equipment with an ISOBUS jobcomputer M The jobcomputer of the farm equipment in use is connected to the terminal M In the jobcomputer the geometry of the farm equipment is configured 1 Measure the distance between the
73. rd 14 4 3 1 Inserting the SIM card 15 4 4 GPS Receiver 16 44 1 Connecting the GPS Receiver to the terminal 17 4 4 2 Entering the position ofthe GPS Receiver 17 For machines fitted with an ISO jobcomputer 18 For machines not fitted with a jobcomputer 19 5 Basic control principles 21 5 1 Getting to grips with the controls 21 5 2 Initial start up 22 5 3 Using the function keys 23 5 4 Restarting the terminal 24 5 5 Inputting data 25 6 Opening applications in the selection menu 26 6 1 Display layout in the selection menu 26 6 2 Opening applications 27 Copyright M ller Elektronik GmbH amp Co KG 3 Contents MUELL ER lectronics We CAN do it 6 3 Segmentation of the display 2 7 Configuring the terminal in the Service application 29 7 1 Controls in the Service application 29 7 2 Icons in the Service application 30 1 3 Changing the language 30 74 Adjusting the brightness for day or night mode 31 15 Configuring the basic display settings 32 7 6 Activating and deactivating applications 33 7 7 Activating licenses for full versions of the software 34 7 8 Deleting files from the USB flash drive 35 7 9 Deleting pools 36 7 10 GPS Receiver 37 7 10 1 Activating the GPS Receiver 37 7 10 2 Configuring the DGPS Receiver A100 38 7 11 Configuring the GPS TILT Module terrain compensation 40 7 12 Screenshots 41 7 12 1 Configuring the screenshots function 41 7 12 2 Creating screenshots 41 7 13 Activating the Diagnostics function 42 1 13 1 Jo
74. rface counter 15 56 ha 2 Distance counter 6 48 km Time counter 0 02 h 2 Select the name of an assigned or deactivated worker on the list 3 Press and hold for 3 seconds gt Norker will be activated Copyright M ller Elektronik GmbH amp Co KG 19 TaskManager application mn MUELLER Step 4 Starting a task l E MUELLER We CAN do it Procedure 2 You can activate a worker who was not previously assigned to the task as follows 1 Click on the following line on the Task data screen The following screen will appear rr TSK 1 Worker 1 B plant protection 2 00 Field 2 01 03 2011 00 00 00 W Mueller K 2 00 Field 2 fem Worker 1 4 202 00 l ha Mix Water AVENTIS C Gay ME_ISO_SPRAYER amp worker 1 5 plant protection ety Filling Emptying sd ME_ISO_SPRAYER Yolume counter 117 001 Surface counter 15 56 ha 2 Distance counter 6 48 km Time counter 0 02 h The name of the assigned worker will appear on the screen However this worker has not yet been activated Add worker A list of names of available workers will appear 3 Click on the desired worker on the list The following screen will appear ge TSk 1 Worker 1 B plant protection 2 00 Field 2 01 03 2011 00 00 00 worker 2 W Mueller 01 03 2011 15 28 17 K 2 00 Field 2 fem Worker 1 4g 202 00 l ha Mix
75. rmPilot We CAN do it 7 16 1 Activating FarmPilot To activate FarmPilot on your terminal you must first activate its driver NOTICE High costs from prolonged data transfer If you do not have a flatrate in your mobile phone contract continuous use of FarmPilot can lead to high costs If your flatrate has a data volume limit continuous use of FarmPilot can quickly use up your data volume limit o Deactivate the FarmPilot driver when you are not using the portal Procedure 1 Switch to the Driver settings screen Service Driver settings The following screen will appear re ers t Diagnostics t FarmPilot t LightBar t Camera 2 Click on FarmPilot 3 Click on the TPD driver gt Next to the driver the icon G will appear 4 Restart terminal gt The following function icon will appear on the start screen of the Service application R You have activated the FarmPilot portal You must now enter the access data for the FarmPilot portal 7 16 2 Configuring the connection with FarmPilot Before you can connect the terminal to FarmPilot you must configure the connection You will receive this data when purchasing the FarmPilot access data Parameters You will require the following parameters for the configuration Username Username for FarmPilot Copyright Muller Elektronik GmbH amp Co KG 47 Configuring the terminal in the Service application guring
76. rtal 7 12 1 Configuring the screenshots function Procedure VI You have activated the Diagnostics function gt 42 1 Start the Service application gt Service 2 m Open the Diagnostics screen 3 Click on Screenshot settings 4 Click on Activate screenshots The status of the function is displayed on the icon Function activated iv Function deactivated 5 Click on Storage location gt The line will be highlighted with a frame 6 Select USB to save screenshots on the USB flash drive 7 Select Portal to send screenshots to the FarmPilot portal 7 12 2 Creating screenshots Procedure M You have configured the Screenshots function M If you want to save the screenshots to the USB flash drive you will already have inserted the USB flash drive into the terminal 1 Open any screen Copyright Muller Elektronik GmbH amp Co KG 41 We CAN do it Configuring the terminal in the Service application al er MUELLER T Activating the Diagnostics function E MuELLER 2 Press the following buttons in the order displayed and keep them pressed for a short while on older terminals you need to press the buttons in reversed order gt While the screenshot is being captured the icon of a photo camera will be displayed in the centre of the display gt When the camera icon disappears the screenshot has been created gt You will find the screenshot you
77. s of several folders will appear gt Ifthe pool is empty nothing will appear 3 Click on the desired folder 36 Copyright M ller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application GPS Receiver We CAN do it The contents of the folder will be displayed 8 USB amp z Pools gt a00c80f80c400000 e SE56FEN iop 140 2KB e SI56FEN iop 141 5KB e SIS6FDE iop 142 0KB a00c80000c400457 The names of the folders are the ISO IDs of the applications whose temporary data they Store 4 Select the desired file a 9 Delete file gt Deleting file 6 Restart terminal 7 10 GPS Receiver When you connect a GPS Receiver to the terminal you must activate and configure it 7 10 1 Activating the GPS Receiver In order to activate the GPS Receiver you must first activate its driver A driver is a small program that controls connected farm equipment The drivers for the farm equipment supplied by M ller Elektronik are pre installed on the terminal Procedure 1 Switch to the Driver settings screen ED Service Driver settings gt The following screen will appear re gt EEE t Diagnostics t FarmPilot LightBar amp Camera 2 Select GPS 3 Click on GPS Copyright Muller Elektronik GmbH amp Co KG OF Configuring the terminal in the Service application MUELLER GPS Receive
78. sk data screen Documenting filling and emptying With ISO machines filling and emptying are automatically documented With non ISO machines you can document filling and emptying using the TaskManager application You can evaluate the documented values in the FarmPilot portal After weighing a tipper truck the driver can enter that he has loaded 20 tonnes of maize After spreading 5000 litres of manure with a non ISO manure truck the driver can enter the quantity spread as emptying Thus you can document the filling or emptying of a container for non ISO machines Copyright Muller Elektronik GmbH amp Co KG 83 TaskManager application an MEmueLLER Step 5 Using the TaskManager application during work lectronics We CAN do it VI You have started a task 1 Open the Task list screen 2 Click on the following line om Filling Emptying The following screen will appear TSK131 B fertilization 2 00 Field 2 eer W Mueller SS 2 00 Field 2 fem Worker 4g 268 00 I ha AHL 28 66917572ter Gay ME_ISO_SPRAYER worker 5 fertilization ets Filling Emptying P ME_ISO_SPRAYER 3 Press the desired function key Jh 4 Enter filled capacity en Enter emptied capacity The following screen will appear 1SK131 B fertilization 2 00 Field 2 eee W Mueller amp 2 00 Field 2 fem Worker 94 268 00 l ha AHL 28 66917572te
79. st activate its driver You can order the external LightBar from Muller Elektronik with the following item number 30302490 Procedure 1 Switch to screen Driver settings gt Service Driver settings The following screen will appear re S t Diagnostics t FarmPilot LightBar t Camera 2 Click on LightBar The installed drivers will appear 3 Click on the LightBar_ME driver gt Next to the driver the icon will appear 4 Restart terminal You have activated the external LightBar 44 Copyright Muller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application lectronics We CAN do it Camera 7 15 Camera 7 15 1 Activating a camera If you have connected a camera or camera system to the terminal you must activate it To activate a camera or a camera system you must first activate its driver Procedure 1 Switch to the Driver settings screen gt Service Driver settings 2 The following screen will appear 0 5 t Diagnostics t FarmPilot t LightBar t Camera 3 Click on Camera 4 Click on the Camera_ME driver gt Next to the driver the icon will appear 3 Restart terminal The following function icon will appear on the start screen of the Service application 6 You have activated the camera driver 7 15 2 Operating the camera Controls
80. sting data on the USB flash drive 62 Copyright Muller Elektronik GmbH amp Co KG TaskManager application Miemuetter ae SRP lectronics Step 2 Selecting a task to process We CAN do it 1 The dispatcher will send you the task data The following notification will appear New task data available 2 Confirm The data are not on the terminal yet but are ready to be downloaded 4 3 Load the data from the portal the arrow on the icon must point downwards gt The following notification will appear Start downloading task data 4 Confirm The data are being loaded 5 Open the Task list screen gt All tasks from the set of tasks will appear on the Task list screen gt You have received a set of tasks from the dispatcher You can process the tasks from the set of tasks 8 3 Step 2 Selecting a task to process Before you start working you must first select the task you wish to process The following options are available to you Create a new task on the terminal Resume an existing task 8 3 1 Creating a new task on the terminal You can create a new task directly on the terminal When creating a task directly on the terminal you will not need to fill it with task data right away You can process a task and then enter into the Farm Management Information System what you have done and on which field The following options are available to you Create a new
81. t 7 7 As second serial interface 2 3 4 5 Joint shaft CAN_H Operating position sensor Legend 1 Digital input pursuant to ISO 11786 1995 chapter 5 2 2 Digital input pursuant to ISO 11786 1995 chapter 5 3 3 Analog input pursuant to ISO 11786 1995 chapter 5 5 4 The pin is switched in parallel with pin 4 by port C Total loading is 600mA Copyright Muller Elektronik GmbH amp Co KG Maintenance and servicin MME mueLLER 3 lectronics Technical specifications We CAN do it 9 4 4 Pin assignment of port C Port C is an RS232 interface Pb Damage to the equipment caused by short circuit Pin 4 of port C is live The voltage depends on the operating voltage of the terminal and is used to supply the DGPS Receiver A100 from M ller Elektronik Other GPS Receivers may suffer damage if connected to this port Before connecting a different GPS Receiver Check what voltage the terminal is connected to 12 V or 24 V Check the pin assignment of the GPS Receiver Check the allowable voltage for the GPS Receiver Compare the terminal voltage to the allowable voltage for the GPS Receiver Compare the pin assignment Only connect the GPS Receiver to the terminal if the voltage range and pin assignment of both devices don t differ from each other Pin assignment of port C Signal DCD RxD TxD Voltage supply for GPS receiver A1001 GND DSR RTS CTS RI 5 V Legend 1 The pin is switc
82. t USB to save data on the USB flash drive The USB flash drive must be inserted in the terminal 6 Select Portal to send data to the FarmPilot portal FarmPilot must be activated before data can be transferred 7 Click on Activate CAN Trace gt The status of the function is displayed on the icon Copyright Muller Elektronik GmbH amp Co KG 43 Configuring the terminal in the Service application Ba ii MEmueLLER T Activating an external LightBar lectronics We CAN do it gt The icon G must appear next to Activate CAN Trace 8 Restart terminal gt After restarting the terminal CAN Trace will log the communication between the terminal and the jobcomputer 9 Leave the terminal switched on until the set CAN Trace duration has elapsed gt The CAN Trace function will be deactivated automatically 10 If you specified USB as the storage location verify that the file StartupTrace txt exists on the USB flash drive E TRACK Leader html StartupT race txt O TaskData_work O Screencopy O nastore OD fieldfinder 11 If this file is missing you must run the CAN Trace function again 12 Email the Startup Trace txt file to Customer Services If you chose Portal as the storage location this file will have been sent automatically 7 14 Activating an external LightBar If you connected an external LightBar to the terminal you must activate it To activate the external LightBar you must fir
83. th the FarmPilot portal to run smoothly The SIM card must meet the following requirements It must be GPRS capable It must be PIN free Inform your mobile phone provider about this requirement before purchasing the SIM card The contract must enable data transfer Copyright Muller Elektronik GmbH amp Co KG MUELLER Mounting and installation lectronics Aa We CAN do it 4 3 1 Inserting the SIM card Required tool Torx TX10 screwdriver Procedure 1 Switch off the terminal and disconnect all cable connections to other equipment 2 Unscrew the SIM card cover on the reverse of the terminal Use a Torx TX10 screwdriver 4 Raise the card holder The card holder can be raised on the right hand side where the casing is rounded The card holder is held in place by hinges on the other side Copyright Muller Elektronik GmbH amp Co KG 15 Mounting and installation i MUELLER GPS Receiver l E MUELLER We CAN do it 5 Slide the SIM card into the card holder Following installation the chip on the card must be in contact with the circuit board The card must be positioned as shown in the picture 7 Press the card holder lightly onto the circuit board until it clicks into place on the right hand side 8 CAUTION Tighten the screws but not too tight otherwise the cover might be damaged 9 Screw the cover back on Make sure that the rubber seal is positioned between the cover and t
84. the icon E 10 Confirm entries gt The data you entered will be saved The rate will appear on the Task data screen Measure Procedure 1 Click on the following line and hold for two seconds gt A list of available measures will appear Copyright M ller Elektronik GmbH amp Co KG 13 We CAN do it TaskM er application Me askManager applicati MUELLER Step 3 Entering and saving task data lectronics 2 Select a measure gt The selected action will appear on the Task Data screen 8 4 2 Saving task data u You can only save the task if the function icon a appears on the Task data screen Once saved the task data can no longer be altered Procedure VI You have created a new task and entered the task data M You are on the following screen i TSK 2011 02 24 11 54 48 Si W Mueller 2 00 Field 2 fem Worker 4 250 00 Iha Be yplant protection N fertilization 2 00 Field 2 I f fertilization 2 00 Field 2 W Mueller K200 Field 2 fem Worker a 1 Save task data This function icon will only appear if saving the task data is possible The following screen will appear Tl fertilization 2 00 Field 2 D 2011 02 24 11 54 48 mt we 2011 02 24 11 54 48 BR Mule A ee The saved task will appear on the Task list screen The name comprises the date and time the task
85. the text may appear in a foreign language in German In this chapter you will learn how to change the language of the terminal 1 Switch on the terminal 2 gt Press Copyright Muller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application fectronics Adjusting the brightness for day or night mode We CAN do it The following screen will appear Service 8x26 BxABBB1DEBACABUAHF sS7h2de 6x87 XAG CSOOGACAOOOGA TaskManager zm OXF BxABBGS2GGGC49GAGF TRACK Leader Emme Bx1C 6xABGG17GG8C49BAGF C 3 Click on Service The following screen will appear File management Driver settings fh Plugin settings 7 License management ME Terminal V 03 90 00 The texts on this screen may appear in a foreign language 4 Click on Terminal Einstellungen Display settings 5 Click on Sprache Language 6 Select the abbreviation of your language T Press gt The following message will appear Changes will be adopted after restart 8 Press gt The language in the Service application will be changed Language will be changed in other application only after a terminal restart 9 Restart terminal gt The language in other applications will be changed 1 4 Adjusting the brightness for day or night mode In this chapter you wi
86. tion 48 Copyright Muller Elektronik GmbH amp Co KG MUELLER Configuring the terminal in the Service application Configuring FarmPilot We CAN do it Parameters The values you must enter for the parameters depend on your mobile phone provider You can find out these data from your mobile phone provider You will require the following parameters for the configuration Country Country for which the SIM card is configured Cannot be altered Provider Name of the mobile phone provider Appears automatically With unrecognised cards you can enter the name of the mobile phone provider yourself APN Abbreviation of Acces Point Name Address of the GPRS access point DNS 1 and DNS 2 Abbreviation of Domain Name System IP addresses of the first and second DNS servers Number Dialling code for the modem Cannot be altered Username Username for the GPRS connection Password Password for the GPRS connection Controls Function icon Retrieve default values Procedure You can configure the mobile connection as follows M You have inserted the SIM card M You have activated the FarmPilot portal 1 Switch to the configuration screen for the GPRS connection XK Od Provider Copyright M ller Elektronik GmbH amp Co KG 49 Configuring the terminal in the Servi licati onfiguring the terminal in the Service application MUELLER U Configuring FarmPilot l FEMUELLER We CAN
87. ts a line that can be clicked on with the rotary knob Switching between screens On the display of the COMFORT Terminal the screens are arranged side by side However only one screen is active at any one time The active screen is always the one in which the cursor has been placed To switch to a different screen you must first activate it The following options are available to you Switch to the Task data screen from the right hand section Switch to the right hand section from the Task data screen Controls Switch to the Task data screen if a task has been started Switch to the Task list screen if no task has been started Back gt 4 Master data screen The Master data screen is the start screen for the TaskManager application From this screen you can access all other screens You can identify the Master data screen by this icon You will find the icon in the upper section of the screen af w JTasks X Fields 28 Farms B customers wip Farm equipment B worker GF Products mt E Me TM 02 00 60 TC 00 13 01 Master data screen 56 Copyright M ller Elektronik GmbH amp Co KG TaskManager application MUELLER ne lectronics Basics We CAN do it In the main section of this screen you will see folders which contain the data stored in the Farm Management Information System If
88. ure 1 NOTICE There is a very sensitive contact pin in the center of the GSM antenna Make sure not to damage the contact pin when screwing on the GSM antenna 2 Screw the GSM antenna on the rear side of the terminal Copyright Muller Elektronik GmbH amp Co KG 13 SIM card 4 2 2 4 3 SIM card Which SIM card 14 Mounting and installation Terminal ports MUELLER lectronics We CAN do it Rear of the terminal Version with a GSM modem and camera connections 1 GSM antenna port Only for terminals with a GSM modem installed 2 Not currently in use 3 Port for analog camera Only for terminals with a GSM modem installed Item no 30322527 4 Port for analog camera Only for terminals with a GSM modem installed 5 USB port USB 1 1 Covering cap for USB port Prevents dust from entering the USB socket SIM card slot Port B CAN bus port For connection of a working position sensor for TRACK Leader Il Port A CAN bus port To connect the ISOBUS basic equipment Port C Serial port RS232 The terminal must be equipped with a SIM card so that you can use the FarmPilot portal If you do not intend to use the FarmPilot portal you will not need any SIM card You must purchase the SIM card from your mobile phone provider Select a mobile phone provider that can guarantee good mobile phone reception on your fields A good connection is required in order for your work wi
89. vices don t differ from each other The DGPS Receiver A100 has a status LED which shows the quality of the connection red The DGPS Receiver is connected to the terminal but has no GPS reception orange GPS reception is working green DGPS reception is working During initial start up it can take approx 30 minutes until the GPS Receiver has reception At subsequent start ups it will only take approx 1 2 minutes Procedure VI The GPS Receiver is mounted on the roof of the tractor 1 Switch off the terminal 2 Guide the connection cable from the GPS Receiver into the cab 3 CAUTION Ensure that the cable is not laid across sharp edges or at risk of becoming bent Lay the cable in a place where nobody can trip over it 4 Connect the connecting cable of the GPS Receiver to port C on the terminal 4 4 2 Entering the position of the GPS Receiver When you have mounted and connected the GPS Receiver you must enter its exact position The position of the GPS Receiver is also referred to as the GPS Receiver offset Copyright Muller Elektronik GmbH amp Co KG 17 Mounting and installation ee MUELLER GPS Receiver l E MUELLER We CAN do it In order to enter an accurate position for the GPS Receiver you must measure the distances of the GPS Receiver from the longitudinal axis and from the so called attachment point gt 19 When entering distances please note that it is essential to specify whethe
90. was created You have saved the task New parameters will appear on the Task data screen 74 Copyright Muller Elektronik GmbH amp Co KG TaskManager application Miemuetter en lectronics Step 4 Starting a task We CAN do it Machine Worker You will only be able to alter these parameters once you start the task 8 5 Step 4 Starting a task You can start every task irrespective of its status Procedure 1 Switch to the Task list screen The following screen will appear lla fertilization 2 00 Field 2 fertilization 2 00 Field 2 Mueller 2 00 Field 2 fem Worker 2 Click on the desired task The following screen will appear Fettization 2 00 Feld 2 I fertilization 2 00 Field 2 eee W Mueller 2 00 Field 2 fem Worker 4 268 00 I ha AHL 28 66917572ter Gay ME_ISO_SPRAYER amp worker 5 fertilization fertilization 2 00 Field 2 W Mueller SS 2 00 Field 2 fem Worker 3 Start the task Copyright M ller Elektronik GmbH amp Co KG 15 TaskManager application MUELLER Step 4 Starting a task l E MUELLER We CAN do it The following screen will appear F af So D IESE EP Tasks B fertilization 2 00 Field 2 9 Fields a 28 Farms i W Mueller GB customers GY 2 00 Field 2 wip Farm equipment fem Worker CB worker a 268 00
91. you move the cursor right down to the bottom using the rotary knob you will be able to see additional folders containing master data Task list screen The Task list screen contains the names of all tasks stored on the USB flash drive ie You can identify the Task list screen by this icon k You will find the icon in the upper section of the screen EN oT 1x12 it teten ooren B plant protection 2 00 Field 2 B plant protection 2 00 Field 2 Sc A plant protection 4 00 Field 4 W Mueller plant protection 5 00 Field 5 K 2 00 Field 2 fem Worker a 202 00 l ha Mix Water AVENTIS C Say ME_ISO_SPRAYER worker E plant protection ets Filling Emptying ba ME_ISO_SPRAYER plant protection 1 00 Field 1 W Miller amp 1 00 Field 1 fem Worker Task list screen Beneath the task list you will find the background information about the respective task you selected You can identify the status of the task by the colour of the icon preceding the name of the task Tasks whose names are preceded by an asterisk are copies of other tasks The following table contains an overview of all icons used to mark the different types of tasks light yellow Tasks that have not been started yet dark yellow Paused tasks red Stopped tasks Tasks processed by the Master Copyright M ller Elektronik GmbH amp Co KG 57 TaskM licati askManager application MUELLER Basics lectronics We

Installation and operating instructions

Contents

Download Pdf Manuals

Related Search

Related Contents