Operating instructions S 7000 series vacuum cleaners
Contents
1. 20 Maintenance 22 Purchasing new dustbags and filters 22 Ordering the correct dustbags andfilters 22 Whento Change the dustbag III awa 23 Replacing the dustbag WI ceeredaedigebae WAWA pee dew ed oe bes 24 When to change the dust compartment filter 25 How to change the dust compartment filter 25 When to change the erhaustfilter 26 Replacing the Super Air Clean filter 27 Replacing an Active Air Clean filter or an Active HEPA filter 28 Replacing one type of exhaust filter withanother 29 Removing threads and hair from the Electrobrush 30 Cleaning and care 32 Problem solving guide 33 After sales service 34 Optionalaccessories 35 Electrical connectionforthe UK 39 Caring for the environment Disposal of packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Ensure that any plastic wrappi2. 29 Maintenance Removing threads and hair from the Electrobrush mg Switch the Electrobrush and the vacuum cleaner off switch it off at the wall socket and remove the plug m Release the vacuum cleaner and place it flat on the floor m Turn the vacuum cleaner over m Cut any threads or hairs that have become entangled in the roller with a pair of scissors There is a groove along the roller to help you Then run the vacuum cleaner to vacuum up the bits 30 Maintenance The suction hose can be opened up to clean out any heavy soiling or blockages Any large particles inside it can then be easily removed m Raise the vacuum cleaner into the vertical position m Press the release button on the telescopic tube and remove the suction tube handle m To increase stability turn the elbow joint at the bottom of the hose downwards as illustrated until it clicks into position above the retainer Unlock the hose socket by turning it in the direction of the arrow Now remove the hose socket from the elbow by pulling it m Remove any soiling or blockages m Replace the socket and lock it into position If you have not been able to reach all of the soiling you could also try the following Unlock the panel on the base of the vacuum cleaner as follows Using a coin loosen the two screws as far as possible Lever off the panel m Remove any soiling or blockages m Replace the pa
3. Checking the dustbag change indicator m Raise the vacuum cleaner into the vertical position m Switch on the vacuum cleaner using the On Off control on the handle and select the highest power setting m Tilt the cleaner until you can see the colour marker in the dustbag change indicator easily The front of the Electrobrush will lift up as you do this If the marker completely fills the dustbag change indicator you should replace the dustbag with a new one How the dustbag change indicator works The dustbag change indicator is set for normal household dust This generally contains a mixture of dust hair carpet fluff threads grit etc However if the cleaner has been used to vacuum up fine dust Such as plaster brick dust cement or flour the pores of the dustbag will become blocked very quickly This affects the air permeability of the bag and the marker will indicate that the bag is full even when it is not If this happens you must still change the dustbag because suction power will be greatly reduced by blocked pores in the dustbag If on the other hand you have vacuumed up a large amount of hair and carpet fluff which typically contains a lot of air the indicator may fail to react even though the bag is full You should still change it Both these extremes can occur 23 Maintenance Replacing the dustbag m Raise the vacuum cleaner into the vertical position m Raise the release
4. m Open the exhaust filter compartment lid m Remove the filter grille m Open the filter grille and remove the used Super Air Clean filter by one of the clean unsoiled sections m Replace it with a new Super Air Clean filter If you wish to replace the Super Air Clean filter with an Active Air Clean filter or with an Active HEPA filter see Replacing one type of exhaust filter with another m Secure the catch on the filter grille and replace it inside the exhaust filter compartment m Close the exhaust filter compartment lid Maintenance Replacing an Active Air Clean filter or an Active HEPA filter Do not use more than one exhaust filter at a time m Open the exhaust filter compartment lid m Remove the exhaust filter m Fit the new exhaust filter in position If you wish to replace the Active Air Clean filter or the Active HEPA filter with a Super Air Clean filter see Replacing one type of exhaust filter with another m Close the exhaust filter compartment lid Re setting the exhaust filter change indicator If your vacuum cleaner is fitted with an exhaust filter change indicator reset button this needs to be re set each time the filter is replaced To do this the vacuum cleaner must be switched on m Press the reset button The exhaust filter change indicator goes out and resets to zero The filter change indicator can only be reset by pressing the reset button after the l
5. eee Viele Operating instructions S 7000 series vacuum cleaners To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before using it for the first time en GB These operating instructions apply to the standard S 7000 vacuum cleaners as well as to other models which are distinguished by names rather than numbers M Nr 07 460 200 Contents Caring for the environment 3 Guide to the appliance 4 Warning and safety instructions 7 Preparingforuse 10 Using the IBADA ee Wa 11 Unwind the mains Cable si 20 4 denned paw KI pee See MALE eae 11 SW NN sasaaa Ai E a aa AA AAA apenas ede eee EA 12 Releasing the vacuum cleaner 12 Switching ON ANGLO AA IAEA EE hate 13 Adjusting the suction power ia IAEA 13 Vacuumingusingthesuctionhose 16 Vacuuming usingthetelescopictube 17 Using the Electrobrush 18 Recommended WI bd ded be dedoe di deed bd ddeebbed baad hina deas 18 Switching the Electrobrushonandoff 19 how touse the El6CtrObIUSN cen e d eked hin sae wanes AR ee Ree ee Pe 19 Using the accessories supplied
6. as suction would be reduced by the blocked pores PD Use only genuine Miele dustbags filters and accessories This will ensure optimum performance of the appliance throughout its life The manufacturer cannot be held liable for damage caused by non compliance with these Warning and safety instructions Preparing for use Assembling the cleaner m Raise the vacuum cleaner into the vertical position m Insert the handle into the vacuum cleaner until it clicks into position 10 Using the cleaner Unwind the mains cable The lower cable hook can be turned in either direction m Turn it upwards to release the cable Winding up the mains cable When the cleaner is not in use the cable can be wound around the two cable hooks Secure the mains cable by clamping the plug to the cable see detail Using the cleaner Switching on m Whilst vacuuming the mains cable can be fed through the guide at the side of the upper cable hook see detailed drawing This way the mains cable will not getin the way during vacuuming This also protects the cable from becoming kinked Releasing the vacuum cleaner m Step on the foot switch and tilt the cleaner to a comfortable position for vacuuming 12 Using the cleaner Important please observe the flooring manufacturer s cleaning and care instructions Switching on and off m Press the On Off button on the handle The vacu
7. of the following exhaust filters a Super Air Clean filter Replace this filter every time you start a new packet of Miele dustbags A Super Air Clean exhaust filter is supplied with every packet of Miele dustbags b Active Air Clean filter black c Active HEPA filter blue These types of filter need to be changed approx once a year Make a note of the date on the filter Exhaust filter change indicator Certain models are fitted with an exhaust filter change indicator reset button to show you when to change your Active Air Clean b or Active HEPA c filter The indicator lights up after approx 50 hours of operation which is equivalent to about a year of average use The vacuum cleaner can still be used with the exhaust filter indicator lit up However the suction power will be reduced as will the effectiveness of the filter if it is not replaced in good time The filter change indicator light is irrelevant if a Super Air Clean filter a is fitted as long as it is replaced every time a new packet of Miele dustbags is started The indicator light will go out when the reset button is pressed 26 Miele eeesse VEsts air clean Miele 000000000000000000000 Q00000000000000000000 QO0000000000000000000 0000000000500000000533 Q00000000030000500083 000000000000000000000 Maintenance Replacing the Super Air Clean filter Do not use more than one exhaust filter at a time
8. the appliance read these instructions carefully before using it for the first time They contain important notes on its safety operation and maintenance Keep these instructions in a safe place and ensure new users are familiar with the content Pass them on to any future owner Always disconnect the vacuum cleaner from the mains supply when you have finished using it as well as for maintenance work and cleaning Switch it off at the wall socket and unplug it Correct application P gt This vacuum cleaner must only be used for domestic household purposes to vacuum dry floor surfaces Do not use on people or animals Any other usage modification or alteration is at the owner s risk and could be dangerous The manufacturer cannot be held liable for damage resulting from improper or incorrect use of the appliance P gt This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it by a person responsible for their safety Safety with children gt This appliance is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or to use the controls Supervise children whilst you are using it P gt Older children may only use the vacuum cleaner if its operation has been clearly explained to them and
9. the plug must not be used until a suitable replacement is obtained The colour of the correct replacement cover is that of the coloured insert in the base of the plug or the colour that is embossed in words on the base of the plug as applicable to the design of plug fitted Replacement fuses should be ASTA approved to BS1362 and have the correct rating Replacement fuses and fuse covers may be purchased from your local electrical supplier 39 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 01235 554455 Fax 01235 554477 Customer Contact Centre Tel 08707 554466 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd A C N 005635398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Hong Kong Miele Hong Kong Limited AIA Plaza 24 Floor 18 Hysan Avenue Causeway Bay Tel 852 2610 1331 Fax 852 2610 1013 E mail mielehk miele com hk nternet www miele hk Ireland lele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele ie nternet www miele ie New Zealand Miele New Zealan
10. Department or a Miele authorised service technician gt Switch the vacuum cleaner off switch off at the wall socket and remove the plug before changing accessories P Do not let the vacuum cleaner get wet Clean only with a dry cloth or slightly damp cloth when disconnected from the mains supply If moisture gets into the appliance there is a risk of electric shock Correct use P gt Never touch the Electrobrush roller while it is rotating Danger of injury gt To avoid the risk of damage do not use the vacuum cleaner without the dustbag dust compartment filter and exhaust filter in place gt if a dustbag is not inserted the dust compartment cover does not normally close Do not force it P gt Do not vacuum up any water liquid or damp dirt This will cause major faults and could seriously impair the functioning and electrical safety of the appliance Wait until any freshly cleaned or shampooed carpets or floor coverings are completely dry before attempting to vacuum gt Do not vacuum toner dust Toner such as that used in printers and photocopiers can conduct electricity The filter system in the vacuum cleaner may not filter it completely causing the toner to be blown back into the room by the fan gt Do not vacuum up any inflammable or combustible liquids or gases and do not vacuum in areas where such substances are stored The cleaner might explode Warning and safety instructions P Do
11. button and open the lid to its resting position m Pull on the tab at the side of the collar and swing the bag up away from the suction socket before taking it out of its holder The dustbag has a closing flap which closes automatically to prevent any dust escaping m Fit the new dustbag into the holder as far as it will go Leave it folded up when you take it out of the box m t should be unfolded in the dust compartment m Close the dust compartment lid securely making sure it clicks into position Take care not to trap the dustbag when doing so The dustbag is then automatically guided into position for vacuuming Warning The lid will not close without a dustbag in place or if the dustbag is incorrectly fitted Do not force it 24 Maintenance When to change the dust compartment filter Replace this filter every time you start a new packet of dustbags A dust compartment filter is supplied with every packet of Miele dustbags How to change the dust compartment filter m Open the dust compartment lid m Unclip the filter frame and remove the old filter Hold by the clean unsoiled section see arrow to remove it m Replace with a new dust compartment filter m Close the filter frame m Close the dust compartment lid firmly It should click into place 25 Maintenance When to change the exhaust filter Depending on model your vacuum cleaner will be fitted as standard with one
12. d Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264353 Fax 0800 463453 Internet www miele co nz South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za Internet www miele co za Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House ll Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg Internet www miele sg United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved S 7000 3808 CE M Nr 07 460 200 00
13. ean filter replaces the filter fitted in the vacuum cleaner There is no difference in the filtration levels between the Active Air Clean filter and the Super Air Clean filter Active HEPA filter A combination filter which complies with the requirements of EN 1822 HEPA classification 12 It is able to filter out very fine particles and micro organisms The active charcoal layer absorbs odours from the dust collected in the dustbag This filter is specially appropriate for allergy sufferers and users requiring exceptional standards of hygiene The Active HEPA filter replaces the filter fitted in the vacuum cleaner Do not use aroma capsules in your cleaner if you use either of these filters The charcoal in them will absorb their aroma rendering them ineffective 38 Electrical connection for the UK All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the Uk The voltage and connected load are given on the data plate located underneath the vacuum cleaner Please ensure that these match the household mains supply The fuse rating is quoted on the plug The appliance is supplied with a cable and moulded plug ready for connection to a 230 240 V 50 Hz a c single phase supply Non rewireable plugs BS 1363 The fuse cover must be re fitted when changing the fuse and if the fuse cover is lost
14. easily remedy please contact your Miele Dealer or the Miele Customer Contact Centre see back cover for address Please note that telephone calls may be monitored and recorded to improve our service 34 Optional accessories Miele accessories including floorheads filters and dustbags are available to order from your local Miele retailer the Miele Spare Parts Department or via the internet on www miele shop com Certain models are supplied as stan dard with one or more of the following accessories Attach the accessory required onto the suction hose handle or onto the telescopic tube Important please observe the flooring manufacturer s cleaning and care instructions Hardfloor brush This brush is designed for use on hard flooring such as tiled or stone floors Parquet floorbrush This brush has natural bristles and is designed for use on parquet floors and other surfaces which are susceptible to scratching such as laminate flooring The Parquet floorbrush bristles can be cleaned with the vacuum cleaner using the crevice nozzle if necessary 35 Optional accessories Parguet Twister swivel action floorbrush Suitable for all types of hard flooring including parguet and tiled floors This floorbrush is particularly good for accessing awkward corners and niches Parguet Twister KL swivel action floorbrush This floorbrush is 90 mm wider than the Parquet Twister floorbrush mak
15. hanism has been activated by the appliance overheating or because of a blockage m Switch the Electrobrush and the vacuum cleaner off switch it off at the wall socket and withdraw the plug m Check the cleaner for any blockages and all the filters in the vacuum cleaner Do not use the vacuum cleaner for about 20 30 minutes to allow it to cool down The Electrobrush switches off automatically The Electrobrush indicator lights up red The red lamp indicates a blockage in the roller for example because a large object has been vacuumed up m Switch the Electrobrush and the vacuum cleaner off switch it off at the wall socket and withdraw the plug m Remove the blockage The vacuum cleaner can then be used again The Electrobrush switches off automatically The Electrobrush indicator stays yellow The overheating protection mechanism has been activated by the appliance overheating or because of a blockage m Switch the Electrobrush and the vacuum cleaner off switch it off at the wall socket and withdraw the plug m Check the cleaner for any blockages and all the filters in the vacuum cleaner The Electrobrush has to cool down To speed this up m Switch the vacuum cleaner back on m Vacuum for about 10 minutes without switching the Electrobrush on This will cool the Electrobrush down and it can then be used again as normal 33 After sales service In the event of a fault that you cannot
16. ight has come on Pressing the button at any other time will have no effect 28 Maintenance Replacing one type of exhaust filter with another Depending on model your vacuum cleaner will be fitted as standard with one of the following exhaust filters a Super Air Clean filter b Active Air Clean filter black Miele c Active HEPA filter blue radeon 000000000000000000000 Q00000000000000000000 QOQ000000000000000000 QO0O00000000000000000 QOQO00000000000000000 OOOH HAHAHAHA Miele Please note 1 If you wish to replace the Super Air Clean filter a with an Active Air Clean filter b or an Active HEPA filter c it is essential that you remove the filter grille before fitting the new type of filter 2 If you wish to replace the Active Air Clean filter b or the Active HEPA filter c with a Super Air Clean filter a then it is essential that you also fit a filter grille Filter grille see Optional accessories Do not use more than one exhaust filter at a time The exhaust filter indicator light with reset button that is fitted on certain models is designed to come on when the Active Air Clean or Active HEPA filter needs to be changed The filter change indicator light is irrelevant if a Super Air Clean filter is being used as long as it is replaced every time a new packet of Miele dustbags is started The indicator light will go out when the reset button is pressed
17. ing it ideal for cleaning larger floor areas Hand held Turbobrush The hand held Turbobrush is intended for vacuuming upholstery mattresses car seats carpeted stairs etc Radiator brush This brush can only be used if attached to the crevice nozzle For cleaning radiators narrow shelves and crevices 36 Optional accessories Mattress nozzle For cleaning upholstery mattresses cushions curtains covers etc Upholstery nozzle 190 mm Extra wide upholstery nozzle ideal for cleaning upholstery mattresses and pillows quickly Micro Set This set is specially designed for cleaning small objects and difficult to reach areas such as PC keyboards stereo equipment intricately carved furniture and ornaments models etc It consists of Micro hose with combination nozzle crevice nozzle and dusting brush Micro dusting brush Micro crevice nozzle Angled extension 37 Optional accessories Universal brush For dusting books shelves etc Filter grille The filter grille is reguired if you wish to fita Super Air Clean filter instead of an Active Air Clean filter or an Active HEPA filter see Maintenance Replacing one type of exhaust filter with another Active Air Clean filter This is a special active carbon filter which absorbs odours coming from the dirt collected in the dustbag keeping unpleasant smells to a minimum The Active Air Cl
18. inges always draw the Electrobrush from the middle of the rug or carpet across the fringe towards the floor Using the accessories supplied The following accessories are stowed at the back of the cleaner Upholstery nozzle 2 Crevice nozzle 300 mm 3 Dusting brush with natural bristles Attach the accessory required onto the suction hose handle or onto the telescopic tube Upholstery nozzle For cleaning upholstery mattresses cushions curtains covers etc 20 Using the accessories supplied Crevice nozzle 300 mm For cleaning in folds crevices or corners and narrow gaps Dusting brush with natural bristles For cleaning skirting boards ornate or carved articles etc The head of the dusting brush can be swivelled to attain the best cleaning position 21 Maintenance Warning Always disconnect the vacuum cleaner from the electrical supply before any maintenance work Switch off at the wall socket and withdraw the plug The Miele filter system consists of three filters which must be replaced from time to time to ensure that your vacuum cleaner performs efficiently Dustbag 2 Dust compartment filter for motor protection 9 Exhaust filter To ensure that your vacuum cleaner functions correctly cleans hygienically and gives you many years of trouble free operation please only use genuine Miele approved dustbags and filters This ensures optimum performa
19. l vacuuming with the cleaner the suction tube handle should be stowed away on the telescopic tube Make sure the handle is also correctly hooked into its holder on the cleaner see detail in the top illustration 16 Using the cleaner Vacuuming using the telescopic tube Warning Do not use the telescopic tube at head level to avoid the risk of injury e g to eyes and ears Warning To prevent the risk of injury when vacuuming the stairs ensure the cleaner is placed in a stable position at the bottom of the stairs or on one of the lower steps m Raise the vacuum cleaner into the vertical position m Lift the handle out of its holder to access the telescopic tube m To increase stability turn the elbow joint at the bottom of the hose downwards as illustrated until it clicks into position above the retainer One part of the telescopic tube is packed inside the other and it can be adjusted to suit your height for comfortable vacuuming m Press the telescopic tube release button see arrow and adjust it to the required height For normal vacuum cleaning the telescopic tubes must be pushed back together Make sure the handle is also correctly hooked into its holder on the cleaner see detail in the top illustration Using the Electrobrush Recommended use Important please observe the flooring manufacturer s cleaning and care instructions The Electrobrush is particularly suitable for inten
20. nce of the vacuum cleaner and the dustbags Warning The use of non Miele approved dustbags and accessories could invalidate your warranty and cause damage to your appliance 22 Purchasing new dustbags and filters Replacement dustags and filters can be obtained from your local Miele retailer the Miele Spare Parts Department see back cover for contact details or via the internet on www miele shop com Ordering the correct dustbags and filters This vacuum cleaner uses Miele HyClean dustbags with a green holder and the code U ORIGINAL Miele A dust compartment filter and a Super Air Clean exhaust filter are supplied with every packet of Miele dustbags If you wish to purchase dust compartment filters or exhaust filters separately please quote the model number of your appliance when ordering to ensure you get the correct items The model number is located on the data plate underneath the Electrobrush You can replace the exhaust filter fitted in the vacuum cleaner with one of the other Miele exhaust filters if you wish see Optional accessories Maintenance When to change the dustbag Change the dustbag when the colour marker in the dustbag change indicator fills the display or sooner if it is no longer effective see possible reasons for this below Miele dustbags are disposable and intended to be used only once Do not attempt to re use as suction would be reduced by the blocked pores
21. nel and lock it with the Screws 31 Cleaning and care Warning Always disconnect the vacuum cleaner from the electrical supply before cleaning it Switch off at the wall socket and remove the plug Vacuum cleaner and accessories External surfaces of the vacuum cleaner and of the accessories can be cleaned with a dry or a slightly damp cloth or with a proprietary cleaner suitable for plastic E Cloth A microfibre E Cloth is available from the Miele UK Spare Parts Department or via the internet at www miele shop com This is suitable for cleaning surfaces such as stainless steel glass plastic and chrome without the use of chemicals Warning Do not use abrasive cleaning agents glass cleaning agents or all purpose cleaners Because of their chemical composition they could cause serious damage to the plastic casing 32 Dust compartment The dust compartment can if necessary be cleaned using a dry duster dusting brush or if available a second vacuum cleaner to vacuum the dust out Warning Do not let the vacuum cleaner get wet If moisture gets into the appliance there is a risk of electric shock Problem solving guide The vacuum cleaner switches off automatically Vacuum cleaners with a rotary selector dial The vacuum cleaner in operation indicator lights up red Vacuum cleaners with buttons The thermal cut out indicator lights up red The overheating protection mec
22. ngs bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Rather than just throwing these materials away please recycle them Disposing of the dustbag and filters These are made from environmentally friendly materials and can be disposed of with the normal household waste as long as they have been used exclusively for general household dust Disposal of your old appliance Before disposing of your old appliance remove the dustbag and all the filters and dispose of them with your normal household waste Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or ask your Dealer for advice Ensure that it presents no danger to children while being stored for disposal Guide to the appliance 0O09 The illustration shows the maximum number of features available on these Miele vacuum cleaners Guide to the appliance Upper cable hook for mains cable 2 Suction hose holder 3 Suction hose with handle 9 Release button Telescopic tube Dust compartment filter for motor pro
23. not vacuum up anything which has been burning or is still glowing e g cigarettes ashes or coal whether glowing or apparently extinguished The cleaner might catch fire P Do not vacuum up items which are heavy hard or have sharp edges They could cause a blockage and damage the appliance P Do not use the suction hose or telescopic tube at head level to avoid the risk of injury e g to eyes and ears gt Do not use the Electrobrush at head level Danger of injury gt Do not vacuum near items such as curtains scarves clothing etc as these could be vacuumed in and become entangled in the roller PD Monitor the change dustbag indicator and change the dustbag if necessary Check the exhaust and dust compartment filters at the same time and change them too if necessary A full bag or blocked filter will reduce the suction power of the cleaner A temperature limiter switches the vacuum cleaner off automatically if it gets too hot See Problem solving guide Accessories Miele accessories including floorheads filters and dustbags are available to order from your Miele retailer the Miele Spare Parts Department or via the internet on www miele shop com P It is not advisable to vacuum directly with the handle i e without an accessory attached as the rim could get damaged and you could hurt yourself on sharp edges gt Miele dustbags are disposable and intended to be used only once Do not attempt to re use
24. power automatically adjusts itself to suit the type of flooring or carpet being vacuumed m Press the Automatic button Automatic The button lights up yellow To stop using the automatic setting simply press the Automatic button again Warning Do not use the Automatic setting to vacuum lightweight materials or curtains These could be sucked in and possibly damaged Tip Obstacles and variations in floor height for instance when vacuuming over thresholds and the edges of rugs are easy to cope with m Briefly press the footswitch and lift the front of the floorhead over the obstacle Using the cleaner Vacuuming using the suction hose Warning Do not use the suction hose at head level to avoid the risk of injury e g to eyes and ears Warning It is not advisable to vacuum directly with the suction hose i e without an accessory attached as the handle end of the hose could get damaged and you could hurt yourself on sharp edges Warning To prevent the risk of injury when vacuuming the stairs ensure the cleaner is placed in a stable position at the bottom of the stairs or on one of the lower steps m Raise the vacuum cleaner into the vertical position m To access the suction tube handle press the release button on the telescopic tube m To increase stability turn the elbow joint at the bottom of the hose downwards as illustrated until it clicks into position above the retainer During norma
25. sive vacuuming of carpets which are subject to hard wear It is very effective at removing deep seated dirt and preventing areas of frequent use being trodden into a path Warning Please note that the Electrobrush should not be used for vacuuming deep pile rugs and carpets or valuable hand knotted rugs and carpets e g Persian and oriental rugs etc There is a danger of the threads being pulled out If in doubt contact the carpet manufacturer retailer Warning Do not use the Electrobrush to clean highly variable or uneven floors The brush might come into contact with the floor and cause damage 18 Using the Electrobrush Switching the Electrobrush on and off The roller on the Electrobrush is driven by a motor which can be switched on and off m Press the Carpet button on the handle The Electrobrush will switch on The Electrobrush in operation indicator light in the control unit will light up yellow This button enables you to switch the Electrobrush off during vacuuming and the vacuum cleaner will continue to operate using suction only This is useful when moving from vacuuming a fitted carpet to a rug for example The Electrobrush will switch itself off automatically as soon as the cleaner is raised to its upright position How to use the Electrobrush m To achieve the best results pass the Electrobrush slowly backwards and forwards over the carpet or floor covering For rugs and carpets with fr
26. tection Telescopic tube release button 8 Vacuum cleaner foot release Exhaust filter Exhaust filter compartment Electrobrush B Light 43 Dustbag change indicator Dust compartment release button HyClean dustbag 49 Control unit see next page 47 Mains cable Button to switch Electrobrush from carpet to hard flooring 49 On Off button Handle Those features marked depend on the model and may vary or not be available on your model At the rear Lower swivel hook for mains cable Upholstery nozzle Carrying handle Crevice nozzle Dusting brush with natural bristles 6 Telescopic tube holder Guide to the appliance Depending on model your vacuum cleaner will be fitted as standard with one of the following control units Vacuum cleaners with a rotary selector dial Vacuum cleaner in operation indicator light 2 Electrobrush in operation indicator light 3 Rotary suction power selector Vacuum cleaners with buttons Automatic button 2 Suction power selector buttons buttons Thermal cut out indicator light 9 Electrobrush indicator light Exhaust filter change indicator Reset button Electrobrush in operation indicator light ss Warning and safety instructions This appliance meets statutory safety reguirements Improper use can however lead to personal injury and material damage To avoid the risk of accidents and damage to
27. they are able to use it safely recognising the dangers of incorrect use Technical safety P Ensure that the connection data on the data plate voltage and frequency match the mains electricity supply It is essential that they match to avoid damage to the appliance gt The plug must be fitted witha 13 A fuse Uk gt gt Before using the vacuum cleaner check for any signs of damage Do not use a damaged appliance it could be dangerous P While the vacuum cleaner is under guarantee repairs should only be undertaken by a service technician authorised by Miele Otherwise the guarantee will be invalidated Warning and safety instructions gt Repairs should only be carried out by a Miele authorised service technician Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work P Do not pull or carry the vacuum cleaner by the cable Keep the cable away from sharp edges and do not let it be squashed for example under a door Avoid running the vacuum cleaner over the cable A damaged cable plug or socket is a safety hazard The appliance must not be used if any of these have suffered damage P Do not use the vacuum cleaner if the cable is damaged A damaged cable can endanger your safety gt gt If the cable is damaged the complete cable unit must be replaced For safety reasons this must only be done by the Miele Service
28. um cleaner will switch on Vacuum cleaners with a rotary selector dial The vacuum cleaner in operation indicator light in the control unit will light up yellow Vacuum cleaners with buttons The vacuum cleaner suction power settings in the control unit will light up yellow For good visibility of the working area the light on the floorhead will come on Adjusting the suction power The suction power can be regulated to suit the type of flooring being cleaned The controls vary from model to model The different options are described on the following pages Rotary selector m Turn the suction power selector manually to the setting you require O S Using the cleaner buttons Some models also have symbols on the control unit which indicate the type of use the settings are suitable for N curtains lightweight fabrics upholstery cushions carpets rugs and runners Q for daily energy saving vacuuming This setting is also very quiet lightly soiled rugs and fitted carpets heavily soiled hard flooring and for intensive cleaning of carpets m Press the button to select a higher suction power level m Press the button to select a lower suction power level The setting selected will light up yellow 14 Using the cleaner Automatic suction power regulation on vacuum cleaners with buttons The suction
Download Pdf Manuals
Related Search