T3667-60A POOL ASSEMBLY AND INSTALLATION MANUAL
Contents
1. SHORT TIE STRAP 32 FIGURE 5 FIGURE 5 LONG TIE STRAP 32 LONG TIE STRAP 15 X 24 15 X 30 18 X 33 SHORT DELTA Step 3 Attach the left and right sides INTERLOCK mm of the delta uprights to the bottom SLIDE DOWN TO TOP UPRIGHTS A F BOTTOM RAIL gt beams as shown in Figure 3 Slide kk the tee clip through the slot in the bottom rail and attach to the top of the bottom beam as shown in FIGURE 3 BOTTON Figure 3A Bolt the tie straps to the AUTA RAIL adapter plate then attach the adapter plate to the bottom beam as shown in a Figure 3 See Figure 2 for correct tie B LT strap placement Slide the two TEE CLIP s correct delta interlocks over the left and right delta upright pieces as OGG eee eens ee shown Slide the vinyl cap onto the oS ends of the bottom beams as shown LONG DELTA in Figure 3 I INTERLOCK l 3 8 X 5 8 BOLT 5 8 X 1 BOLT TEE CLI BE SURE TO BOLT THE TEE 1 N CLIP TO THE TOP OF THE a BOTTOM MEAN AS SHOWN da 3 8 NUT O VINYL p 5 87 NUT END CAP 4 Pad TIE STRAP 3 8 X 5 8 BOTTOM RAIL BOTTOM BEAM BOLT ADAPTER 3 8 NUT PLATE FIGURE 3A Step 4 Interlock the mud sills 3 87 16 X 5 8 S S ae into the bottom rail as shown in CAP SCREW j i Figure 3 Bolt the Mud sills to 3 PER CONNECTION the bottom rail as shown Attach A eon2. BARRIERS ETC ANY HOME BUILT OR PREFABRICATED DECKS SHOULD CONFORM TO THE LOCAL CODES AND BOCA NATIONAL BUILDING CODE THE ELECTRICAL CODE MAY REQUIRE A PERMIT AND INSPECTION AND USE OF GFCI DEVICES OR OTHER CONDITIONS THE ELECTRICAL INSTALLATION MUST ALSO CONFORM TO ARTICLE 680 OF THE NATIONAL ELECTRIC CODE INSTALL THE FILTER AND PUMP IN ACCORDANCE WITH THE MANUFACTURERS INSTRUCTIONS ARTICLE 680 STATES THAT YOU MUST BOND THE SWIMMING POOL PUMP TO THE SWIMMING POOL THIS CAN BE DONE BY ATTACHING A 8 COPPER WIRE FROM THE BONDING LUG ON THE PUMP TO AN UNPAINTED METAL SURFACE ON THE POOL WALL OR BOTTOM CLIP THE INSTALLATION OF AN ABOVE GROUND SWIMMING POOL WILL USUALLY REQUIRE THREE PEOPLE TO HELP ASSEMBLE IT DANGER THIS POOL EVEN IF SUPPLIED WITH A DEEP AREA CONFORMS TO THE NATIONAL SWIMMING POOL INSTITUTE STANDARDS FOR A TYPE O NON DIVING POOL DIVING SLIDING OR JUMPING INTO THE POOL MAY CAUSE PARALYSIS DEATH OR PERMANENT INJURY CUSTOMER SERVICE DEPARTMENT 8600 RIVER ROAD DELAIR NEW JERSEY 08110 3398 USA DANGER 1 DO NOT DIVE OR JUMP INTO YOUR POOL DO NOT USE A POOL SLIDE ON THIS POOL YOUR POOL CONTAINS SHALLOW WATER AND IS NOT DESIGNED FOR HEADFIRST ENTRY DIVING OR SLIDING OR JUMPING DIVING SLIDING OR JUMPING CAN RESULT IN A BROKEN NECK IF YOU STRIKE THE POOL THIS CAN RESULT IN PARALYSIS DEATH OR PERMANENT INJURY INFORM ALL FAMILY AND GUESTS OF THESE RULES AND POINT OUT WARNING LABELS IT IS NECESSARY TO MAINTAIN
3. CAN WEAKEN THE POOL WALL WHICH COULD RUPTURE RELEASING THE POOL WATER WHICH COULD CAUSE BODILY HARM AND PROPERTY DAMAGE 3 FOR NIGHT TIME USE YOU MUST PROVIDE LIGHTING TO ILLUMINATE THE POOL SAFETY SIGNS AND DECK SURFACES LIGHTING MUST COMPLY WITH ARTICLE 680 OF THE NATIONAL ELECTRIC CODE IT IS IMPORTANT THAT USERS BE ABLE TO SEE THE SHALLOW DEPTH OF THE POOL AT ALL TIMES 4 THE FOLLOWING BASIC LIFESAVING EQUIPMENT MUST BE ON HAND AT ALL TIMES A ALIGHT BUT STRONG POLE SHEPHERD S CROOK NOT LESS THAN 12 LONG B A 1 4 THROWING ROPE AS LONG AS 1 1 2 TIMES THE MAXIMUM WIDTH OF THE POOL WHICH IS ATTACHED TO A COAST GUARD APPROVED FLOTATION DEVICE SUCH AS A RING BUOY C A TELEPHONE SHOULD BE NEARBY WITH A LIST OF EMERGENCY TELEPHONE NUMBERS SUCH AS POLICE amp AMBULANCE 5 ADDITIONAL POOL SAFETY RELATED PUBLICATIONS ARE AVAILABLE FROM THE FOLLOWING NATIONAL SPA AND POOL INSTITUTE CONSUMER PRODUCT SAFETY COMMISSION 2111 EISENHOWER AVE WASHINGTON DC 20207 ALEXANDRIA VA 22314 IMPORTANT INSTALLATION ITEMS 1 LEVELNESS POOL MUST BE LEVEL WITHIN 3 4 UNLEVEL POOLS PLACE EXTREME FORCES ON THE POOL WHICH MAY DEFORM 2 WALL CLOSURE THE POOL WALL MUST BE FASTENED TOGETHER PROPERLY WITH BOTH BARS AND FASTENERS IN ALL HOLES OMITTED BARS OR FASTENERS CAN CAUSE THE WALL TO RUPTURE DESTROYING THE POOL AND INJURING PEOPLE 3 SAND COVE THIS SUPPORTS THE LINER AND MUST BE PACKED SOLID IF IT COMPRESSES SHIFTS OR ERODE
4. 8 x33 5 1 4 3 1 2 14 8 SELECTING THE POOL SITE 1 Check your local building codes and acquire proper building permits For poor soil conditions consult a professional engineer 2 The pool site must be absolutely level and solid The area must be free from stones and roots 3 To protect the pool from chemicals and foreign matter in the soil you may use a ground cover under the sand base Do not install your pool on asphalt tarpaper grass wood gravel clay concrete or treated soils 4 Position your pool away from trees overhead wires structures such as a house or garage or septic fields GROUND PREPARATION Your pool must be installed on a solid level surface perform the soil test as shown below Position stakes as shown on figure 1 and use a farm level or transit to level the area shown Remove all grass roots and stones Start at the lowest spot remove all high spots do not fill in low spots The area must be absolutely level Lines 1 through 6 of the following table refers to Figure 1 Soil Test Dig a hole in the pool area one foot square and one foot deep and fill with water If at the end of one hour the water has not completely soaked in the following steps must be taken 1 Round Ends 3 patio blocks must be placed under each bottom clip as shown in figure 8 2 Oval Midsections A concrete footing must be placed under the end of each Delta upright along both sides and down the length of the bottom rail Consult a local profes
5. A 4 HIGH BARRIER TO REDUCE THE CHANCE OF A CHILD ACCESSING AN UNSUPERVISED POOL THE BARRIER MAY BE A FENCE WALL OR COMBINATION THEREOF WHICH COMPLETELY SURROUNDS THE POOL BARRIERS MUST COMPLY WITH THE LOCAL BUILDING CODE BOCA NATIONAL BUILDING CODE OR THE CONSUMER PRODUCT SAFETY COMMISSION BARRIER STATEMENT THE FOUR FOOT HIGH POOL WALLS USUALLY PROVIDE THIS BARRIER HOWEVER IF THE POOL IS LESS THAN 48 ABOVE GRADE OR HAS BUTTRESSES OVAL POOLS YOU MAY NEED ADDITIONAL FENCING TO PROVIDE THIS BARRIER CONSULT WITH YOUR BUILDING OFFICIAL FOR SPECIFIC REQUIREMENTS FENCING OPTIONS ARE AVAILABLE FOR YOUR POOL PLEASE CONTACT YOUR POOL DEALER YOU MUST MAINTAIN A 5 WIDE CLEAR ZONE AROUND THE POOL AND DECK OR FENCING DO NOT ALLOW TOYS CHAIRS TABLES OR SIMILAR CLIMBABLE OBJECTS IN THIS CLEAR ZONE ENABLING CHILDREN TO CLIMB AND GAIN ACCESS TO THE POOL THE FILTER EQUIPMENT MUST ALSO BE LOCATED OUTSIDE OF THE CLEAR ZONE 4 YOU MUST RAISE AND LATCH OR SECURE YOUR POOL LADDER OR POOL ENTRANCE WHEN THE POOL IS NOT IN USE Adherence to the above items will reduce the frequency of preventable child drownings in swimming pools WARNING YOUR POOL IS SUPPLIED WITH WARNING SIGNS WHICH MUST BE AFFIXED TO THE POOL AS SPECIFIED IF YOU BUILD A DECK THE TWO AREA SIGNS MUST BE AFFIXED TO THE DECK AT THE POINT OF ENTRY VISIBLE TO PEOPLE ENTERING THE POOL AREA FAILURE TO INSTALL OR IMPROPER LOCATION OF SAFETY INFORMATION WILL SUBJECT
6. B PRA holes in the wall do not use the wall and notify POOL WALL BEFORE your dealer at once DIMENSIONS SPREADING THE SAND ARE TO TOP _____ z TO HELP PREVENT NOTE If the wall does not stay in the wall OF WALL O RSA channel the ground is not level remove the WALL POOL WALL wall and relevel the wall channel NI After the pool wall is assembled check the Wa O dimensions of the pool to insure that it has not shifted during assembly WALL NEK sips WARNING Failure to use the sand or sand i equivalent and shape it as specified will void all warranties on the pool and liner FIGURE 13 Steps 13 through 15 are for overlap liners only For beaded liners proceed to step 16 3090138 OVERLAP LINERS Step 13 Remove the liner from the carton and unfold into the pool Be careful not to drag abrade or snag the liner Spread the liner out over the entire bottom of the pool Raise the liner side wall Step 14 See Figure 14 Detail 14A Figure 15 and Figure 16 Place the liner over the edge of the wall Make sure the overlap is equal around the outside of the pool wall Cut the liner interlock into 2 pieces and center the 1 pieces of the liner interlock over the liner at each upright Place the bead receiver over the liner interlock and liner as shown to secure the liner in place Step 14A See Detail 14B for a J Bead Liner Place J Hook bead of the liner on top of the wall and push down firmly Then plac
7. D RECEIVER O DELTA UPRIGHT JS INER Rea PT Rz i WALL WALL FIGURE 17 FIGURE 18 W00033A T00054A BEADED LINERS Step 16 See Figures 17 18 and 19 Place the bead receiver on the wall with the ends centered over the uprights Tape the joints of the bead receiver using fabric tape to protect the liner Step 17 Attach the transition top clips to the top of the transition uprights as shown in Figures 20 and 21 based on the type of pool you have For aluminum frame pools attach a 10 captive nut to the top clip prior to assembling the clip to the transition upright Step 18 Attach a sheet wall upright over top of the transition upright as shown in Figures 22 and 23 based on the type of pool you are installing Lift up one end of the bead receiver and slide the top clip completely onto the first bead receiver until the ends of the bead receiver are centered into the top clip Use this same method on the round ends of the pool Step 19 Remove the liner from the carton and unfold into the pool Be careful not to drag abrade or snag the liner Spread the liner out over the entire pool bottom Locate the triangle shaped tabs on the under surface of the liner These tabs should be lined up with the four transition uprights on the floor of the pool Raise the liner sidewall and place the bead into the bead receiver Smooth all the wrinkles out on the bottom of the liner To remove wrinkles always pull the liner firmly but gently No sharp tugs Be
8. Fo AJ FACE w j PLATE gt GASKET LA O e FACE PLATE FIBER SCREW WASHER FACE PLATE SANDWICH g GAS HG FIGURE 29 POOL WALL lt w Se W00024 RUBBER GASKET Pa I jA DZ WALL FITTING ff WA YY DIRECTIONAL BALL 5 NN RETURN ASSEMBLY POINT OPENING AWAY DIRECTIONAL BALL FROM SKIMMER FITTING l in B j WARNING After N completion of the bisa FIGURE 30 A pool the pool must SA00003B SA00004 _ SA00005 never be drained to DANGER Ke eS less than 1 2 full gt l Damage to the DECKSIDE NTC structure and or liner _ DANGER a POINT OF may result ENTRY 7 Note Refer to Page 2 CAUTION a Re 1 i oy f Warning section for Label z D ig Letter Designations my TF N ADDITIONAL ye DN C amp D DANGER SIGN SEE A S SIDE DECK MANUAL A Z RA A POINTOF lt i POINT OF ENTRV ENTRY B N d Jar jka eb A BOW _ C amp D C amp D 14
9. PRIGHT i 10 X W gt la HEX HEAD SCREW z x 4 PER UPRIGHT SHEET WALL UPRIGHT 5 FRAME ALUMINUM POOLS FIGURE 23 W00051 BEAD RECEIVER DETAIL 23A A0005D TRANSITION TRANSITION TOP CLIP UPRIGHT l l Ni A a EL u zez N 1 1 1 8 4 A 7 A ni a e IIB UI SHEET WALL z UPRIGHT 7 NE HOX 1 a ty HEX HEAD SCREW SHEET WALL 2 PER UPRIGHT UPRIGHT TOP CLIP nN CAPTIVE NUT X 10 X HEX HEAD SCREW Step 20 Begin to fill the pool with water Use a slow stream of water and fill approximately 1 1 2 deep If the pool is an oval be certain that the blocks under the bottom beams have remained level and that the bottom beams are seated firmly on those blocks Make sure the fit of the liner is correct Smooth out any wrinkles in the pool bottom If installing a deck do not fill more than 12 until the deck is installed Step 21 Fill the pool with 4 to 6 of water Measure the distance from the bead receiver to the water surface at several points around the pool to be certain that the pool is still level WARNING The pool must not be more than 3 4 out of level If the pool is not level drain the water and level the structure Any non compliance with this requirement will void all warranties 11 Step 22 Locate the safety warning copings as described and as shown at the
10. S THE LINER MAY RUPTURE RELEASING ALL THE WATER AND DESTROYING THE POOL AND INJURING PEOPLE 4 THESE POOLS ARE NOT DESIGNED TO BE BURIED THE GROUND FORCES CAN COLLAPSE THE POOL INWARD DO NOT LOCATE YOUR POOL NEAR STRUCTURES SUCH AS A HOUSE GARAGE ETC AS PEOPLE COULD DIVE OR JUMP INTO THE POOL RESULTING IN DEATH OR PERMANENT INJURY 6 ALTHOUGH THERE ARE RELATIVELY FEW PARTS IN YOUR POOL NONE MAY BE OMITTED IN ASSEMBLY EACH PART SUPPLIED IS AN IMPORTANT PART AND IF OMITTED MAY CAUSE POOL FAILURE CHECK ALL PARTS AGAINST THE PARTS LIST WARNING Do not exceed the following torque values for the noted fasteners 1 4 20 S S Fasteners 75 in Ibs 3 8 16 S S Fasteners 236 in Ibs 3 8 16 Aluminum Fasteners 143 in Ibs TOOLS AND MATERIALS PHILLIPS SCREWDRIVER 2 HAND TROWEL EXTENSION CORD HAMMER RAKE SLOTTED SCREWDRIVER 2 GARDEN HOSE amp NOZZLE STRING LINE PLIERS SOCKET WRENCH amp SOCKETS 50 TAPE MEASURE HAND TAMPER TORQUE WRENCH TRANSIT OR FARM LEVEL ELECTRIC DRILL amp BITS GARDEN SHOVEL WRENCHES 1 LONG STRAIGHT 2X4 14 LONG 1 ROLL DUCT OR FABRIC TAPE WHEELBARROW 25 WOOD STAKES 1 CAN WHITE SPRAY PAINT PLASTIC GROUND COVER SAND AND BLOCK CHART SAND 2 x 8 x 16 4 x 8 x 16 POOL SIZE TONS YARDS PATIO BLOCKS CAP BLOCKS 12 x18 2 1 1 4 12 2 12x21 21 2 1 3 4 12 4 NOTE Sand must be 12 x24 3 2 8 6 masons or bar sand and 15 x24 3 1 2 2 1 4 12 4 be free of foreign objects 15 x30 4 2 3 4 12 8 1
11. T3667 60A POOL ASSEMBLY AND INSTALLATION MANUAL Above Ground Aluminum Delta Sheetwall Oval Pools Note Deck and fence accessories shown are optional THIS MANUAL EXPLAINS THE CORRECT METHOD TO ASSEMBLE YOUR NEW SWIMMING POOL READ THESE INSTRUCTIONS AND STUDY THE ILLUSTRATIONS ALSO READ INSTRUCTIONS FOR ACCESSORIES SUCH AS FILTERS LADDERS ETC PAY PARTICULAR ATTENTION TO THE CAUTIONS ON THE FOLLOWING PAGES THE MANUFACTURER IS NOT AFFILIATED WITH ANY PROFESSIONAL POOL INSTALLER THEREFORE THE MANUFACTURER CANNOT ASSUME RESPONSIBILITY FOR ERRORS IN THE INSTALLATION OF YOUR POOL BY THE INSTALLER OR THE HOMEOWNER IF YOU HAVE THIS POOL INSTALLED BY OTHERS PLEASE SUPERVISE TO BE SURE YOUR POOL IS INSTALLED PROPERLY AND THAT ALL THE CAUTIONS LISTED THROUGHOUT THIS MANUAL HAVE BEEN FOLLOWED PAST EXPERIENCE OR SHORT CUTS MAY NOT BE COMPATIBLE WITH OUR POOLS FOLLOW THE INSTALLATION MANUAL THE MANUFACTURER RESERVES THE RIGHT TO CHANGE OR IMPROVE ANY ITEM WITHOUT INCURRING ANY OBLIGATION TO MAKE ANY CHANGES OR IMPROVEMENTS ON ITEMS PREVIOUSLY SOLD AND TO DISCONTINUE MODELS OR CHANGE SPECIFICATIONS AT ANY TIME WITHOUT NOTICE THIS PRODUCT IS SOLD WITH A LIMITED WARRANTY THE TERMS AND CONDITIONS ARE SET FORTH IN THE LIMITED WARRANTY CERTIFICATE PACKED WITH EACH POOL COPIES OF THE LIMITED WARRANTY ARE ALSO AVAILABLE UPON WRITTEN REQUEST YOUR LOCAL BUILDING CODE MAY REQUIRE OBTAINING A BUILDING PERMIT AND MAY HAVE REQUIREMENTS ON SETBACKS
12. YOU AND OR THE INSTALLER TO LIABILITY ARISING FROM INJURY CLAIMS A NO DIVING COPING TWO SUPPLIED THESE ARE TO BE INSTALLED ACROSS THE POOL FROM THE POINT OF ENTRY AND HAVE ONE SECTION OF REGULAR COPING BETWEEN THEM COPING WITH INTERNATIONAL LOGO THIS ONE COPING IS TO BE INSTALLED AT THE POINT OF ENTRY EITHER ADJACENT TO THE A LADDER UNDER THE IN POOL LADDER OR IN THE CENTER OF A DECK DANGER AREA SIGN WITH LOGO T1440 THIS SIGN MUST BE INSTALLED AT THE POINT OF ENTRY FACING ALL USERS AS THEY ENTER THE POOL IF YOUR POOL HAS A FENCE THE SIGN IS TO BE FASTENED TO THE FENCE ADJACENT TO THE LADDER OR ENTRANCE IF YOUR POOL DOES NOT HAVE A DECK OR FENCE ATTACH THE SIGN TO THE EDGE OF THE COPING ADJACENT TO THE LADDER THE SIGN MUST BE VISIBLE TO ALL USERS AS THEY ENTER THE POOL AREA CAUTION SAFETY RULES SIGN 1445 THIS SIGN MUST BE ATTACHED TO THE FENCE DIRECTLY BELOW THE DANGER SIGN OR IF YOU DO NOT HAVE POOL FENCING ON THE COPING NEXT TO THE DANGER SIGN If any signs are missing or damaged contact the customer service department for replacements CAUTION 1 DECK SURFACES MAY BECOME SLIPPERY WHEN WET DO NOT RUN OR DIVE INTO THE POOL FROM THE DECK NOTE SUNTAN LOTIONS AND OILS MAY CAUSE POOL COMPONENTS TO BECOME SLIPPERY 2 EACH MONTH CHECK THE POOL WALL FOR DETERIORATION OR LEAKAGE ESPECIALLY AT THE SKIMMER AND RETURN FITTINGS THE SKIMMER AND RETURN GASKETS SHOULD BE REPLACED EACH SPRING TO PREVENT LEAKAGE DETERIORATION
13. back of this manual Then attach all sections of coping as shown in figures 24 25 and 26 using the outermost holes in the top clips Step 23 See Figure 28 Assemble the coping covers as shown based on the type of pool you are installing i CCE HOLS s b FIGURE 25 FIGURE 24 WA ja _ COPING 4 CO00022 C000012B NE 12 x 4 SS TYPE AB X o o JW DELTA TOP CLIP HEX HEAD WASHER HEAD SELF TAP ak 10 24 l 4 PER TOP CLIP HEX NUT N ALUMINUM POOLS Note Attach the midsection coping to the delta top clips first then attach the coping and top clips to the delta uprights as a complete assembly HO x 4 SELF 7 TAPPING SCREWS FIGURE 26 CO00021 BEAD RECEIVER Step 24 Fill the pool until the water level is 3 inches below the return hole Step 25 Follow the instructions for the filtration system skimmer and return that are supplied with the filter See Figure 29 for additional assistance DANGER When a filter or any other electrical device is added to this pool it is the responsibility of the purchaser to take all necessary precautions as set forth in article 680 of the National Electrical Code and local electrical codes Failure to comply with this requirement may result in a dangerous or hazardous electrical condition which may cause bodily injury or death Step 26 Attach the remaining safety warning signs as described and shown in Figur
14. blocks under the 1 gt E ROR VETO EIT wall channel where needed Dig 2 down for each block The top of each block must be at grade level Place a stake adjacent to each wall channel to keep the half circle in position during installation Repeat for other end i Place the 3 angles into the slot in RETURN gt f ee the bottom rail as shown in Figure a SA 1 z L 8 Insert long end down A IL FIGURE 9 i SKIMMER OPENING W00012 Important Remove the AND plastic shipping film from the wall prior to attaching the enclosure bars to the wall DUCT TAPE INSIDE OF POOL H e 1 20 X 3 4 S S LI MACHINE 4 MA WALL EE E GA ot WALL 1 4 20 S S mmn HEX NUTS OUTSIDE OF POOL Step 9 cont See Figure 9 10 and 11 Place the required amount of sand inside the pool area Starting at the center of a bottom clip insert the pool wall into the wall channel around the entire pool area Make sure the skimmer and return cutout are at the top of the wall and not over a clip or upright Attach the pool wall Important Remove the plastic shipping film from the wall prior to attaching the enclosure bars to the wall 1 4 20 X 3 4 S S 13 4 MACHINE SCREW 3 4 e OUTSIDE 7 7 L SDE OFPOOL if eT WALL L 1 4 208 8 ENCLOSURE HEXNUT BARS i FIGURE 11 NOTE Start wall enclosure strip at the bottom hole on the wall If the enclosure strip does not cove
15. certain liner is centered Time spent removing wrinkles and aligning the liner will give you a neater looking and easily maintained pool The bead must be fully seated in the receiver to prevent it from coming out later when filling pool Check frequently when filling pool with water DUCT TAPE FIGURE 19 W00023 ATTACHING THE TOP CLIPS TO THE TRANSITION UPRIGHTS AT THE FOUR CORNERS OF THE OVAL i i TRANSITION Note When properlv installed the direction of the hole pattern TOP CLIP FIGURE 20 on this clip should form an arrow facing out of the pool BEAD A00017B RECEIVER FOR ALUMINUM POOLS WITH 5 FRAMES ji 12 X 4 HEX HEAD SCREW 10 CAPTIVE NUT 4 PER UPRIGHT FACES TRANSITION OUTSIDE TOP CLIP BEAD WALL ORPOOL 7 RECEIVER TRANSITION UPRIGHT E ZA s 12 X 1 2 HEX a HEAD SCREW 4PER UPRIGHT x A K l WALL MAN ACK UPRIGHT Te Mas FOR ALUMINUM al POOLS WITH 7 FRAMES FIGURE 21 A00017A TOP CLIP FIGURE 22 BEAD CAPTIVE W00050 bi TRANSITION TRANSITION TOP CLIP Ny tN UPRIGHT RECEIVER NO 10X x SELF TAPPING SCREW f 1 DETAIL 23A JN A0005C 7 FRAME A ALUMINUM POOLS l SHEET WALL N A X U
16. e 30 If installing a fence or deck refer to those manuals for proper placement of safety information Step 27 Fill the pool up to the center of the skimmer make sure that all fasteners are tightened properly and your pool is correctly assembled Upon completion of the pool it is important to backfill the pool wall to prevent the sand from washing out from underneath and water from accumulating around the pool which can cause settling or deterioration Backfill should be sand or clean well draining soil Do not use mulch or materials which retain moisture or limestone or materials which are corrosive The backfill should be three to four inches up the wall be sure to cover the bottom beams and slope away to provide runoff Please read the Sensible Way to Enjoy Your Pool booklet and enjoy years of swimming and relaxation 12 COPING COVER ATTACHMENT FOR ALUMINUM POOLS 10 24 X 5 8 MACHINE SCREW COPING Z COVER BEND TABS TO SECURE TO THE COPING 10 24 X 5 8 MACHINE ALUMINUM POOLS WITH ALUMINUM COVERS SCREW a g FIGURE 28 A00027A A00028C A00027B ae z pea PLUG FITS THIS WAY ONLY l 48 X 17 PA l J SELF TAPPING 10 24 X A MACHINE SCREWS ALUMINUM POOLS WITH RESIN COVERS Face Plate 8 X 1 SELF TAPPING SCREWS 13 PIPE TAPE HOSE ADAPTER HOSE kg i A ADAPTER J
17. e bottom rail be certin to insert the 3 angle in the correct direction and the bottom clips on the round ends must be 1 8 above the elevation of the top surface of the bottom rail Also pack the sand cove firmly against the wall along the midsection of the pool to _ i M i i 3 ANGLE provide proper support Failure to do this may cause a wrinkling in the wall around the bottom rail aS onc LEG DOWN the bottom rail and uprights are fixed and the wall must expand around it Some dana danie WALL BOTTOM RAIE minor wrinkling may occur while filling the 5 amp 18X OVALS SHORT ADAPTER pool this is normal for this type of WALL CHANNEL 54 3 8 midsection and does not pose anv structural risk Step 9 See Figure 1 Mark line STAKE 2 as shown in the table on page gt 3 Insert the short wall channel WALL CHANNEL oO Xx 8 X 16 BOTTOM into the adapter See Figure 8 PATIO BLOCK RAI Create a half circle on line 2 by sliding the longer wall channels DETAIL 8A SLOT SIDE UP A00032 BOTTOM CLIP a 4 PATTERN FOR FIGURE 8 FOLLOW POOR SOIL 10 into the bottom clips See Figure 2 8 Place a 2 thick patio block under each bottom clip If the me bottom wall channel is on soft LINE 2 1 00008 ground place additional blocks in a pyramidal shape under the LONG BEAD RECEIVER p BENT BEAD bottom clips for support Also RECEIVER place additional
18. e the bead receiver or wall channel over the J Bead liner and attach the top clips to the uprights Do NOT put the J Bead liner in the bead receiver BEAD z RECEIVER 4 RA EA RECEIVER NOTE LINER BOTTOM LINER INTERLOCK SHOULD BE CENTERED L CUTTOIW ON THE POOL USING SARA THE SEAM AT THE a PERIMETER OF THE pie BOTTOM ASA GUIDE 4 ee _ lt __LINER DETAIL 14A INTERLOCK NOTE THE LINER POOL WALL rp Ma INTERLOCK IS a OVERTAR J BEAD a ES J USED AT EVERY LINER S eT 7 77 BEAD RECEIVER e LINER SAND BASE JOINT AT EACH i UPRIGHT POOL ROOL WALL FIGURE 14 W00023 NOTE If the liner is exposed to the sun for a long time it will stretch and cause wrinkles This can be avoided by waiting until dusk or by spraying cold water on the liner during installation Step 15 Smooth all the wrinkles out on the bottom of the liner To remove wrinkles always pull the liner firmly but gently No sharp tugs Be certain liner is centered Time spent removing wrinkles and aligning the liner will give you a neater looking and easily maintained pool TRANSITION BEAD UPRIGHT RECEIVER DELTA O UPRIGHT 5 m f SG RECEIVER O U OVERLAP LINER ___ o a LINER AE z si d SK lt lt FIGURE 15 wi WALL WO0031A FIGURE 16 W00032A TRANSITION UPRIGHT BEAD RECEIVER O 6 i BEA
19. r the last hole at the top of the wall you should attach it with a 4 20 x 3 4 machine screw CAUTION Installation of the wall in any other manner than precisely described above will cause extensive damage to the pool and may result in injury or death to those people in or around your pool together as shown using the two 2 wall enclosure bars and hardware The heads of the machine NOTE THE TAB ON THE BOTTOM AND PAN HEAD TOP CLIPS ARE ON SKIMMER SCREWS THE OUTSIDE OF THROAT THE UPRIGHT GASKET SKIMMER THROAT GASKET VINYL Wa SKIMMER GASKET CORK DETAIL 12A s W00030 FIGURE 12 W00025 DETAIL 12B 7 UPRIGHT f NL f WALL Tes y WALL CHANNEL BOTTOM z gt lt CLIP PATIO BLOCK KSH LOW PROFILE FRONT cej 4 BOTTOM CLIP ACCESS SKIMMER NI 10 X 1 2 SELF TAPPING SCREWS 4 PER UPRIGHT NOTE THE SKIMMER THROAT GASKET MUST SAND WICH THE WALL LE ONE FLAP OF THE GASKET MUST BE ON THE INSIDE OF THE WALL AND THE OTHER ON THE OUTSIDE screws must be on the inside of the wall Do not omit any fasteners in the pool wall connection The wall will not stay together without all the fasteners Cover the bolt enclosure on the inside with several layers of fabric tape to protect the liner If either wall enclosure strip is missing NOTE TAPE A 3 WIDE damaged or does not align properly with all A
20. s wi q the bottom rail mud sill assembly sE BOLT to the tie straps with 12 X 1 screws as shown in Detail 4 TIE STRAPS SELF TAPPING FIGURE 4 A SCREWS L00015C 3 8 16 S S HEX NUT NUTS ARE ON BOTTOM FIGURE 5 A00029 20 X W NUT 4 X 8 X 16 CAP BLOCK STop If your pool is getting a walk deck or pool fence attach the appropriate post holder or walk deck support at this time See manual supplied with the walkdeck or pool fence Step 5 Bolt together the tie straps across the span of the pool as shown in Figure 4 Once both sides of your mid section is assembled verify that your pool is squared properly by measuring the diagonal distance from the two opposite corners of the bottom rail up sits BOTTOM RAIL 3 8 X 5 8 R BOLTS ko N S No RS 47 20 x 1 2 S S XN N MACHINE SCREW FIGURE 6 e JA api L00053 FI GURE 7 14 20 HEX NUT L00054 Step 6 Dig down and place a 4 X 8 X 16 cap block at the end of each bottom beam as shown in Figure 5 Level the bottom rail with a transit and adjust to be certain it is level Step 7 Attach the transition uprights to the four corners of the bottom rail as shown in Figure 6 Step 8 Assemble the adapter to the mud sill as shown in Figure 7 step e P g HINT It may be helpful to crimp the bottom clip over Important To keep the wall on oval pools properly aligned with the wall channel to keep it from coming loose th
21. sional engineer to determine the size and type of concrete footing to be installed The design load per upright is 4 000 Ibs ALUMINUM WALL OVAL POOLS LINE 1 LINE LINE 3 LINE 4 LINE S LINE 6 12 X 18 7 3 6 3 7 0 GeO 17 7 2 8 12 X21 7 3 6 3 10 0 90 17 7 2 8 12 X 24 Ts 6 3 143 0 12 0 17 7 28 15 X 24 8 6 7 6 AGO 060 204 2 8 15 X 30 8 6 7 6 16 0 160 20 1 26 18 X 33 10 0 SKQ 16 0 1607 2310 2 8 Step 1 Parts Identification See figures in bill of material LEVEL packet Check for installation addendums Step 2 Ground Lavout y Layout the area to be leveled as shown in Figure 1 Measure and mark with spray paint the lines on the ground for your size pool Dig 2 deep to remove all grass from within the pool area clear all debris and level this entire area using a transit Be certain the area is smooth and EXCAVATION all grass stones roots and any OUTLINE other foreign objects have been removed Do not build up or fill low areas Remove all FIGURE 1 high spots L00003B POOL OUTLINE CAUTION For Oval Hopper Pools If this pool is being installed with a deep end refer to instructions TRANSIT packed with the liner NOTE FASTEN TOGETHER ONLY THE CENTER INDICATED BY CIRCLES FIGURE 2 L00034C TIE STRAP LAYOUT 12 X 24 12 X 18 12 X2 SHORT TIE STRAP SHORT TIE STRAP
Download Pdf Manuals
Related Search