USER MANUAL PAR56 LED PAR CANS 153.766
Contents
1. activated mode 5 Caution to prevent Mortal Electrical Risk and Long Life Operation For your safety please kindly pay attention to all the warnings as listed below E Always plug in the power plug last and disconnected from the mains when the device is not in use or before cleaning Do not install and operate the device in rain or extreme heat moisture or dusty locations ES This device is for indoor use only with the environment of dryness a Do not switch on immediately but wait until it reaches room temperature if the device has been exposed to drastic temperature fluctuation E Do not shake the device and avoid brute force when installing or operating a Do not spread the smoke or bubble of effect machine directly to the device qtxlight 2 User Manual 153 766 153 769 Do not use the device during thunderstorms and please disconnect the power Do not use solvents or aggressive detergent to clean the device Use a soft and clean cloth Do not modification the device or the connected power cord without authorization Use appropriate safety rope for safety Do not stare at the light E The symbol o m determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 1m 6 Connect with power supply The ground wire must be connected Use the plug to connect to the main power supply as following 7 Quick Trouble Shooting 7 1 i2. f the unit is not functioning Check if main power is on and fuse is ok 7 2 if the unit is not reacting to music check the sensitivities switch at rear of the device 8 Replacing Fuse Disconnect from the main power supply first then unscrew the fuse holder cover to reveal the fuse Replace the correct fuse rating as stated on lighting or user guide Then screw on fuse holder cover 9 General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently Usage and environment are contributing factors in determining frequency of cleaning As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced lamp life and increased mechanical wear Be sure to power off fixture before conducting maintenance Unplug fixture from power Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components Clean all glass when fixture is cold with a mild solution and a cloth or tissue and drag dirt and grime to the outside of the lens Gently polish optical surface until they free of haze and lint The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can require cleanin
3. g fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days qtxlight i User Manual 153 766 153 769 10 Mounting instruction The fixture may be mounted in any position provide there is adeguate room for ventilation It is important never to obstruct the fan or vents pathway Mount the fixture using clamp Adjust angle of the fixture loosening both knobs and tilting the fixture After finding desired position retighten both knobs When selecting installation location take into consideration lamp replacement access and routine maintenance Safety cables must always be used Never mount in places where the fixture will be exposed to rain high humidity extreme temperature changes or restricted ventilation 11 Dip Switch Setting amp Function 12 1 O me E 1 2 3 4 5 6 7 8 10 11 12 Master sound activated with timeout MO Slave units switch 1 ON 1 2 3 4 5 6 7 8 11 12 Master illusion color changing 12colour circulate fade in amp fade out 9 11 1 2 3 4 5 6 7 8 10 12 Master strobe colour changing effect slow 9 10 11 1 2 3 4 5 6 7 8 12 Master strobe colour changing effect fast 1 9 10 11 12 DMX address select qtxlight i User Manual 153 766 153 769 12 DMX Controlling Channel 1 0 5 off light 6 255 Red 0 100 Dimming Channel 2 0 5 off light 6 255 Green 0 100 Dimming Channel 4 0 160 Master Dimming base on cha
4. nnel 1 3 set up 161 240 Strobe 1 12Hz Second from slow to fast 241 255 Light on base on channel 1 3 set up 13 Disposal a m y s Please disposal of the unserviceable device according to the current statutory requirements 14 Technical specifications 15 Voltage 90 270Vac 50 60Hz Power 30W LED 126LED 46R 40G 40B 010 LED Type 10 Angle 30 Fuse FIA Meas 235 x 195mm V09 06 17 qtxlight i
5. qtxlight USER MANUAL PARS6 LED PAR CANS 153 766 153 769 User Manual 153 766 153 769 Slimline PAR64 LED Par can For indoor use only Caution Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty 1 General Introduction The LED PAR56 is design to create impressive light display of multicolor beams for Family Parties Discos Bars Night Clubs Ballrooms and other locations 2 Features LED Colorful Effect with DMX Controlling Multicolor Beam Projection RGB Mixing color effect or monochrome effect Superior amp Bright 010mm LED Multi controlling DMX 4Channels Master Slave Auto program and Sound Activated Strobe Effect 3 Package Contents Please check the contents to ensure that the content has been received in good condition Light x 1unit User s Guide x 1pcs If you find any accessory is missing or the lighting arrives with any problems please contact your local dealer at once Do not try to fix yourself or you will lose the warranty Please keep the original package and invoice for any possible replacement or returned demand 4 Installation Every person involved with the installation operation and maintenance of this device shall be qualified and follow the instruction of this User Guide When you connect to the mains power and turn on switch the device will illuminate and the light effect will change with music When in sound
Download Pdf Manuals
Related Search