INSTALLATION MANUAL GT7000
Contents
1. Safety precautions ED n Never leave children unattended in the shower or bath Never bath children under 12 using whirlpool function if fitted Regulate the temperature of water before showering Never allow children to use the steam function This function is for ADULTS ONLY Always be aware of the steam outlet pod position Never use in close proximity to the person using it Never use this shower if you have been drinking alcohol Never use with more than one person unless the shower is designed for this This product is not to be used for washing bathing animals 21 www insigniarange com Last Modified 11 07 2014 Steam Generator Connections The steam generator has 3 connections Steam Outlet Connect the white insulated hose to the white steam pod within your shower Make sure these are fitted in the correct position as they are only attached for transportation reasons only Water Inlet Connect a braided hose from the shower valve s centre feed to this opening Drain Connect the grey rubber hose from the steam generators drain opening to the nozzle on the shower waste as shown in the below image IMPORTANT In order for your water to waste from the steam unit you must ensure the spigot has been drilled open All new showers should have this pre done however if not simply run an 4mm drill piece down the spigot which will open it up STEAM BATH GEM Warning 22 www insigniarange2. 7 Align the back panels to the contour of the tray and the roof and once your happy everything is perfectly aligned screw the tray to the back panel using ST12 screws and SW9 washers Step 8 Now the base is securely in position you can attach the roof Using the ST12 screws and SW9 Washers connect the back panels to the roof NOTE If a small gap exists silicone seal later 14 www insigniarange com Last Modified 11 07 2014 Step 9 Taking the left and right hand doors insert the wheels to the top and bottom of each door Ensure the double wheels fix to the top of the door and the single push but ton to the bottom To secure in to place simply unscrew the bolt at the back of the wheel and prise apart the wheel Push the wheel over the bottom top of the door and re attach the bolt To hang the doors carefully carry the door in to the shower and hang the top wheels on to the track Next de press the buttons on the bottom wheels until the wheel falls in to the rail Do this for both doors the close them up together It will be more than likely the doors wont meet correctly at this stage therefore adjust the top wheels by the screw underneath the wheel up or down by screwing clockwise anti clockwise until the doors meet perfectly a a 15 www insigniarange com Last Modified 11 07 2014 Handles Ensuring that the inner thread is protruding out from the handle far enough place the handle on the outside of the door an
3. any circumstances Warranty is void if so as damage will occur If you have a combi supply please use a pressure reducing valve if required to lower the BAR pressure to the shower Please Remember that this product is free standing and is designed to be pulled away from the wall The water supply and waste require flexible pipes If you purchased the fitting kit with this shower you will have the required fittings The water supply pipes need to be at least 1 metre in length and must be that of a flexi braided type DO NOT OVERTIGHTEN IT CAN CAUSE THE CONNECTION TO POP AFTER A FEW WEEKS OF USE Please note if a shower pump is used via gravity system we recommend a separate cold feed bypassing pump direct to generator to avoid damage to the generator Further to this as you would with a washing machine or dishwasher it is highly recommended that accessible water valve taps are installed to turn off the shower when not In use This will avoid any possible flooding due to a burst pipe or connection failure in the future 08 www insigniarange com Last Modified 11 07 2014 Whilst the next steps show you how to assemble your shower we want to make sure you have a correct build to ensure you get a trouble free shower Therefore our advice is to follow the instructions and perform a dry run to ensure you are confident with the build and you understand fully how the unit is assembled When we use the word DRY RUN this means you do not silicone anyth
4. com Last Modified 11 07 2014 Silicone Seal where shown in red on the inside of the shower TESTING FOR WATER LEAKS LEAVING SHOWER 24 HOURS AFTER BUILD ALLOWING SEALENT TO CURE y With all connections tight the waste and hoses checked jets fully sealed your shower still around 18 inches from its designated final resting point and the silicone fully cured hence w leaving for 24 hours minimum Switch on the overhead shower NOT the massage jets re g member these will fire water out at you and are not suitable for checking leaks as they would normally only operate when a person is in front of them Just use COLD water setting as hot g J will make cabin misty and condensate thus the inspection becomes very difficult Now on the Q OUTSIDE of the shower inspect each joint factory seal hose clip and jet by walking from one side and going around to the back and then to the other side finishing at the front If you D have a small leak normally caused through insufficient sealer or air bubble on assembly dry the area thoroughly and reseal on the OUTSIDE Please remember where you see the water I this may not be exactly where the leak is as it could have run around to a low point Never seal your inner fittings accessories inside unless you feel it necessary and make sure it is thin and neat remember you will see this for the life of the shower Again leave to cure and check If all good now check shower functions i e jets for back mas
5. ANSWERS NOW PLEASE KEEP IN SAFE PLACE www insigniarange co uk 25 Internal Items SP074 Monsoon Shower head Ozone Module Roof Lights Hand Shower Holder SP103 Chrome water outlet SP097 Chrome rectangular door han dles os sate sor www insigniarange com Parts List sP204 MK117U Control panel SP227 Standard shower head Sp166 Approximately 4 meters of External Items Part Code Part Description seso Wasenose SP301 White insulated pipe HOSE1MBB 1M braided hose w blue band HOSE1MBR 1M braided hose w red band HOSE1MB 1M braided hose 4 5 Steam Generator SP307 Magnetic door seals n SP155 5 Port 3 Feed Thermo static valve Last Modified 11 07 2014 Framework GT7000 13 Bottom Rail GT7000 4 Left upright Right upright Part Code Part Description Right Backwall Left Backwall 26 www insigniarange com Last Modified 11 07 2014 All images are registered with Image raker Insignia is a registered trademark of Maclean International Ltd All images are subject to copyright Images may not be used in any way shape or form with out written permission from Maclean International Ltd Images are NOT permitted to be saved printed or uploaded Violation of copyright laws are punishable by law 27
6. O THIS AND YOUR WARRANTY IS VOID REGARDS ELECTRICAL ITEMS IF THIS IS NOT UNDERTAKEN YOURS AND OTHERS SAFETY IS PARAMOUNT NEVER ATTEMPT THIS YOURSELF REMEMBER These showers are designed to be free standing and movable from their location should you have need to replace anything ALWAYS USE Flexible braided water inlet pipes at least a metre long not central heating plastic type from house supply to the shower and again flexible waste pipe to join to your house waste NEVER fix with rigid pipes never fix the unit to the wall DURING BUILD LIKE ALL SHOWERS CORRECT SEALING IS IMPERATIVE ALWAYS FIT EASY TO GET TO TAP VALVES ON BOTH HOT AND COLD WATER THE SAME AS A DISHWASHER OR WASHING MACHINE THIS PRODUCT SHOULD BE ISOLATED WHEN NOT IN USE 04 www insigniarange com Last Modified 11 07 2014 YOU WILL NEED TOTAL ELECTRICAL REQUIREMENTS Voltage Rating 220 240AC Frequency Rating 50HZ Power Rating 4 5KW Electric Current Amps 19 Specification for Wiring AWG12 2 05mm Diameter Your electrical contractor should understand ALL legal requirements of connection before undertaking any work or installation UNDER NO CIRCUMSTANCES UNDERTAKE THIS YOURSELF This product MUST be installed with an RCD protection trip for your safety and ensure a minor works certificate has been issued upon completion Always use protection against electrical surge Your shower should be treated the same as a home computer A surge protector sh
7. ck 1x Left Hand Back Panel steam generator fitted behind the seat Box 4 Check 1x Right Hand Back Panel Check 1x Centre Back Panel Last Modified 11 07 2014 06 www insigniarange com Last Modified 11 07 2014 Insignia Screw Pack a Cl ee VERY IMPORTANT Have you got everything If not please contact the Insignia Support Line on 01908 226545 Remember NEVER book your tradesman until everything has arrived been checked and is present No replacement missing parts can be obtained free of charge during or after the build Any claims can only be within the timescale permitted 48 hours after delivery and always BEFORE build 07 www insigniarange com Last Modified 11 07 2014 Pressure Requirements from your house supply We recommend a bar pressure between 2 5 and 3 4 BAR If you have a combi boiler system no problem should be experienced If you have a gravity feed older type installation hot water tank type usually less than 1 bar you will almost certainly need a pump We cannot advise on which type of pump is used location or design because all house plumbing layouts vary This is a job for your installer plumber The end delivery however must fall within the scope above Debit Requirements You will need the debit capabilities of at least 10 litres per minute Again an average combi boiler will supply this but please check if you have a gravity feed system Important Note Do not exceed 3 4 BAR pressure under
8. d secure by tightening the inner chrome Knob to the protruding inner thread Magnetic Seals If not fitted Push the magnetic door seal on the handle side of the glass door ensuring this is tightly fitted ee Door Seals Place the rear door seals on the outer edge of each of the front glass panels as shown on the image on the left hand side 16 Steam Pod Insert the pod from the inside of the shower and attach large white nut from the rear www insigniarange com Accessory Installation AJ Hand Shower 1 Last Modified 11 07 2014 Attach the chrome holder to the back wall via the 2 screws provided in the pack In some cases this maybe pre fitted to the back wall Attach the chrome water outlet to the back of the centre column fixing it from the rear with the hex nut Again this maybe pre fitted Attach the chrome flexible hose to the water outlet with the small coupling end Attach the other end sleeved to the hand shower and place in to the holder NOTE If you attach the wrong end of the hose to the hand shower it will not sit in the holder 17 www insigniarange com Last Modified 11 07 2014 Ozone 03 Unscrew the chrome pepper pot end and drop the white box upside down into the rear hole as shown in the image Now from the inside of the shower re attach the chrome pepper pot end and tighten Monsoon Head Screw the threaded tube in to the top o
9. een the panels for extra sealing and rigidity Note the left hand panel is the panel which houses the steam outlet at the bottom of the panel Secure into position using the B20 N4 SW7 bolts washers and hex nuts as shown in the image below A A 4 A 0 Once you have secured all the panels together it should look like the picture below 10 www insigniarange com Last Modified 11 07 2014 Step 2 Attach the uprights to the curved rails using the ST20 screws Rail with Insignia logo at the top Step 3 Take the 2 front glass panels and lay them down gently Now attach the U shape rubber seal to one side of each panel and cut off any excess 11 www insigniarange com Step 4 Now push the front fixed glass into the frames in the direction as shown by the below arrows and then fix into place using the PRC20 securing clips and ST12 screws Image showing rubber seal on glass before being inserted into position into the frame Last Modified 11 07 2014 12 www insigniarange com Last Modified 11 07 2014 Step 5 Step 6 Take the front frame and meet this to the back panels and screw Alight the roof on to the top of the shower but DO NOT screw into together using the ST12 screws We recommend you use DB6 drill position yet piece to make the pilot hole first www insigniarange com Last Modified 11 07 2014 Step
10. evice 19 St A Guitiet Water Inlet I Drain Important This unit MUST be connected by an electrician and wired back to the main service box and signed off with a minor works certificate This can NOT be plugged in to the wall This is NOT a DIY install www insigniarange com Electric Box Steam Generator Connections Back Light Roof Light STEAM BATH GENERATOR Warning Radio Aerial go kl gt RJ11 Phone Connection BO ermostatic Probe USB Connection Last Modified 11 07 2014 s Bluetooth Connection IMPORTANT S Please ensure you align the arrows carefully as per image Improper connection will damage the pins which are not covered under warranty Phone Connection This feature if fitted has now been disabled Please do not connect as it will not work 20 www insigniarange com Last Modified 11 07 2014 Connection For Tray amp Column Lights Using the supplied extension lead please connect the end with the single connection to your tub lights Next bring the extension lead up the back of the shower and connect one of the plugs to the column lights essentially bridging the two sets of lights together Now with the remaining connection connect this into the wire coming from the electric box with the column light sticker on as shown in the image O O oO O O O AO QO 0 LJ ee coll Aa a Q H OOO ct ay 0 g
11. f the monsoon shower head and pass it up through the light diffuser and through the hole in the shower roof Secure in to position with the hex nut Next Attach the grey hose from your show er valve to the threaded tube using PTFE tape please note this only needs to be hand tight Over tightening will snap damage the tube Thermostatic Probe Insert the probe into the hole situated below the control panel roughly 6mm into the cabin and run clear silicone around the rear side of the probe 18 Rain Shower Hand Shower fy Tl ne Left body jets l Right Back Jets Back Panel Body Jets Open Outlet For Steam Generator www insigniarange com Last Modified 11 07 2014 Shower Valve Shower Valve Connect the hoses to the corresponding inlets on the back of the shower Device output may differ from the image Please refer to your outer chrome faceplate in side your Insignia shower as a reference point IF YOUR DIAL DOES NOT CORROSPOND TO THE APPROPRIATE DEVICE Turn on your water to the shower and note which output the water exits from then turn off the water and swap over the relevant hose Alternatively remove the outer chrome knob by removing the chrome cap and loosening the grub screw please ensure not to unscrew fully as this will drop within the chrome knob this is found on the opposite side to the chrome pillar Once you have succeeded in loosening this you can now slide your faceplate to correspond to the d
12. f the Bluetooth to any current paired devices as only one connection can occur at any one time Note The device you are looking to pair is either INSIGNIA or SPR OUT Last Modified 11 07 2014 MK117U Control Panel Instructions Button 7 Down Arrow Channel select down manual search Button 8 TUN switch Between manual amp auto radio searching Button 9 Up Arrow Channel select up manual search up Button 10 Alarm Activate Alarm Button 11 M Set Steam Time amp Temperature When Radio is active this button will active the arrows to become volume buttons Button 12 03 Press to activate once you finish using the shower Power Button Lock The control panel will automatically lock when not in use for a short time hold this button down for 3 se conds until a beep is heard and this will unlock and reactivate the control panel for use 24 www insigniarange com Need Help Last Modified 11 07 2014 Then simply download the following Help advice booklet found at this link below This contains many useful items such as is your parts warranty registered advice on cleaning servicing your shower cabin fault finding and many more items This is a MUST to read and not just HELP It saves time in nearly all cases avoiding contact with ourselves as most answers are there for a ready fix Simply visit www insigniarange co uk help aspx INSIGNIA PRODUCTS HELP HAVE PROBLEMS AND NEED
13. ing just simply construct the shower align drill and screw everything together Once you are happy with the build take the unit apart and carry out the final fix TO START Make sure you have a clear space remember when finished and in place you need access to check your build and able to pull the shower out for servicing or should you have the need to replace anything Take the shower tub and remove all the protective wrapping and fit the waste If you purchased the fitting kit it is possible this may have already been fitted in the tray hole yet please note this is only for transportation reasons therefore you will still need to ensure the correct sealing and alignment is carried out In the side of the waste supplied in the optional fitting kit you will notice a spigot not seen on an ordinary waste In most cases this is blanked yet should you have a steam version you need to gently drill this out as this item is for the steam generator drainage and will be connected in the instructions later W Now please level the tray by firstly placing the tray in its final location and then using a spirit level adjust the tray feet accordingly Once you are happy with the levelling of the tray you can pull it out to begin the main construction 09 www insigniarange com Last Modified 11 07 2014 Step 1 Take the 3 back panels labelled Left Right and Centre and attach them together as shown below We recommend you place silicone betw
14. ould eradicate the possibility of either the transformer or computer control being burnt out Please Note Earth is required and found on chassis of shower tray A further earth is required from Steam Generator unit Each earth must ground through power supply line Requirements 2tT gt TWO PEOPLE Scissors Stanley Blade Silicone Gun Spirit Level Tape Measure Philips Screwdriver Electric Drill 05 www insigniarange com What s In The Boxes Please use the check boxes to ensure you have everything Should you be missing a part simply call our support line on 01908 226545 or contact us via our website www insigniarange co uk customerservice aspx 1x Shower Tray skirt light pre fitted 1x Roof with Light Diffuser Speaker amp Fan 2x Curved Rails 1 x Screw Pack 1 x Chrome Flexible Hand Shower Hose 1 x Large Monsoon Shower Head 1 x Hand Shower 1 x White Steam Pod 1 x Ozone Module 1 x Black Extension Cable 3 x Braided Hoses 1 x Chrome Connector water outlet for hand shower Prefixed to right hand back wall 1 x Grey Threaded Tube and Hex Nut attachment for monsoon shower head 1 x White insulated pipe 1 x Shower Waste and Hose 1 x Shower Holder pre fixed to right hand wee CO 2 x Glass Doors 2 x Side Glass 2 x Door Magnets Maybe pre fitted to the doors 2 x Plastic Door seals Approx 4 Meters of clear U Style seals 2 x Aluminium posts 2 x T shape joining strips Che
15. sage and hand shower check your joints to these functions at the rear again Never use the shower until all checks have been made and the installer is 100 happy in the knowledge no leaks are present All good Now push your shower FROM THE BASE NEVER GLASS OR FRAME into its final resting position Now you can shower in the knowledge that you have no leaks a job done well and long prod uct life Happy showering Note In some cases it my be prudent to add silicone around the rear base of the shower to add extra water proofing and integrity to the build 23 9 When loading music on to your memory device the play order will be ordered based on the date the files where created www insigniarange com Button 1 Light Bulb Press x1 backlights Press x2 Operates the tray lights Press 3x For All Lights Press 4x To Switch Off Lights Button 2 Steam On Off Button 3 Fan On Off Button 4 USB Connect an external memory device and use the button 7 amp 9 for forward and backward operation Button 5 Radio On Button 6 Bluetooth On Off When activated a beep will sound and the power button will flash purple to notify you that the Bluetooth is searching for a device Power button will be fixed purple when paired with a device To pair another device to your control panel reset the control panel by powering off and powering back on and please ensure you have switch of
16. wer that will last for many years to come Like everything in order to obtain a first class product that will serve you well for many years the effort and correctness put into the assembly will reflect in the quality of your finish OUR BADGE RATING IN TERMS OF DIFFICULTY OF ASSEMBLY IS BASED ON CLIENT FEEDBACK 1 Badge Very easy 2 Badges Easy 3 Badges Moderate 4 Badges Harder than average 5 Badges Professional skills required This shower is rated 5 Badges Edad Eloi 03 www insigniarange com Last Modified 11 07 2014 ASSEMBLY AND SIMPLE PLUMBING THIS PRODUCT BUILD IS RATED SUITABLE FOR DIY PURPOSES PROVIDING THE CUSTOMER IS OF ABOVE AVERAGE SKILLS AND FEELS CONFIDENT IN THEIR ABILTY ONLY YOU THE CUSTOMER WILL KNOW THIS SO BEFORE ANY ATTEMPT IS MADE TO ASSEMBLY READ THROUGH THE FOLLOWING PAG ES IN DETAIL THEN DECIDE IF YOU HAVE ANY DOUBT USE THE SERVICES OF A PROFESSIONAL IN PICKING SUCH ALLOW THEM TO DECIDE IF THEY ARE CAPABLE OF BUILD BY FIRST SHOWING THESE INSTRUCTIONS TO THEM ALWAYS GET THREE QUOTES REMEMBER THE BEST IS NOT ALWAYS THE CHEAPEST REMEMBER PLUMBERS PLUMB 90 OF THIS JOB IS NOT PLUMBING DUE TO THE NATURE OF THIS PRODUCT WE HIGHLY ADVISE THE PURCHASE AND FITTING OF A WATER SOFTENER ELECTRICAL CONNECTION TO HOUSE MAINS WHEN YOUR ITEM IS ASSEMBLED ALWAYS USE THE SERVICES OF A FULLY QUALIFIED ELECTRICAL COMPANY TO COMPLETE CONNECTION FROM SHOWER TO HOUSE SUPPLY LAWS DEMAND IN MANY CASES YOU D
17. www insigniarange com Last Modified 11 07 2014 INSTALLATION MANUAL www insigniarange co uk 30 Day Technical Support 01908 226545 G l 7 0 0 0 NOTE This service is only available to customers from the day of delivery please have your supplier s details and your postcode to hand before calling Replacements Parts inside of your warranty contact www insigniarange co uk customerService aspx Spares Replacements Parts outside of your warranty contact 0844 800 3069 ATTENTION INSTALLERS a App Store WARRANTY REG NO To claim your full 5 year warranty register your shower within 90 days of delivery at www insigniarange co uk warrantyreg aspx Standard 12 month warranty applies if outside this time period These instructions must be left with the customer www insigniarange com Contents Introduction Electrical Requirements What s In The Boxes screw Pack Contents Plumbing Requirements Starting The Installation Electric Box Steam Generator Connections Sealing and Water Testing MK117 Control Panel Instructions Help Book Information Parts List 20 23 24 25 26 Last Modified 11 07 2014 02 www insigniarange com Last Modified 11 07 2014 ll Thank you for your recent purchase of an Insignia shower Please read this booklet with great care to ensure you get the best out of your build and have a sho
Download Pdf Manuals
Related Search