Satel Mini-Link User Guide
Contents
1. Version 1 0 2 SPECIFICATIONS FEATURE min max typical note Supply Voltage Power consumption Serial Interface Response time Operational temperature Transfer rate PULSE COUNTER Inputs 1 pc Minimum pulse width DIGITAL SIGNALS Inputs 2 pcs Outputs 2 pcs IN DICATO RS Indicators O THER OUTPUTS Alarm Output GEN ERAL Housing Connectors Size Lx WxH Weight Mounting IP Modem compatibility 9 30 Vdc 0 03 0 1 VA RS 232 15 Vdc 250 ms 25 55 C 9600 bps max 10 kHz 5 us 0 35 Vdc 0 30V DC AC 1 A Supply Voltage to MINI LINK regulated by the radio modem 5 3 Vdc 40 mA 12Vdc 6 Vdc active RS 232 lt 300 ms 9600 bps 0 30 Vdc resistive 4 5 kQ relay contacts normal open Power ON OFF Digital IN OUT Alarm Pulse IN 9 35 Vdc 30 mA Metal plate painted Alarm supply voltage drive current 30 mA 16 pins for SATELLINE 1870 12 pins for other connections 123 x 85 x 30 mm 80 g Wall plate IP 20 SATELLINE 1870 SATEL MINI LINK User Manual Version 1 0 3 FUNCTIONS Screw connector functions 3 1 Supply Voltage 9 30 Vdc e The minus contacts are in parallel O ne is for the MINI LINK and another can be used for external devices and connections Plus is for supply voltage 3 2 Alarm output AL OUT e The ALO UT is activated when three transmission fails has occurred one after another When activated the ALO UT goes to VDC Driv2. all inputs and outputs that are to be used e Set individual address to all slaves As this is a master slave operation the slaves have to be addressed All slaves must have different address see chapter 3 7 address selection table e Startusing the system by the master by opening the controlling program for example SATELLIN K PC Pro etc e With the program itis possible to turn ON OFF the outputs and monitor the inputs Please contact local SATEL distributor or visit SATEL s web site in order to get information of the multipoint commands 11 SATEL MINI LINK User Manual Version 1 0 5 FACTORY SETTINGS The MINI LINK I O converter is shipped with the following default settings unless specifically ordered with settings other than those listed below FIXED SETTINGS DEFINED AT THE TIME OF ORDER 0 1 sec European std DE Alarm delay 0 No Delay SM Safe mode 0 No Safe Mode 12 SATEL MINI LINK User Manual Version 1 0 Point to Multi point Point to Point Opening of the Radio modem s lock pins with a screw driver SATEL ae I O1 02 MINI LINK 1 0 CONVERTER E A Inputs Outputs EET ME FA Nooooooooooool Supply Supply Alarm Digital Pulse Digital Voltage Voltage Output Inputs Input 1 Relay 9 30Vdc Output Outputs 13 SATEL MINI LINK User Manual Version 1 0 7 ACCESSORIES SATELLINK PC and SATELLINK PC Pro Programs that make it possible to ope
3. FASS amp SATEL USER MANUAL SATEL MINI LINK I O converter SATEL MINI LINK User Manual Version 1 0 TABLE OF CONTENTS TABUE O gee ee Ree ee ane knit Ree hn hae A SC 2 IMPORTANT inode cst ae katte Sel aes Meee tana en ate Mau Mul CUL ne 3 PRO DUCT GO NEOTRMUPE s cret ren teer He EYE FE VEVEY e VECES UEPET vise suas cvtosuedsarseunerbpewecrvensmeretenenspens 4 WARRANTY AND SAFETY INSTRUC TIO 5 uer rr ik c c c e e t c 5 EMO 6 1 1 SATEL MINI LINK PULSE COUNTER AND I O CONVERTER een HH ue 6 2 SPECIFICATIONS uden dm vanes Landes dal ed esie onec Davies doe demde Dar des 7 3 FUNCTION S rear ye St 8 SCREW CONNECTO R FUNC TIO reet tore teer eet Peer eet eere erect eere oer ert Peer eer eerte Doer 8 SUPPE VO TAG Er Q 30 ME er RR CON SUN ECHO ERE E a PEN EH SEN DEREN CHE SUELEN 8 3 22 sAIDARM QUIPUT AL OT d e to tete et erede e e te d be dts 8 SO De re ne RU DU TU 8 3 4 DiGITAL INPUTS 11 12 AND OUTPUTS O 1 02 Hmmm eene rne nnns 8 3 5 e i ce dU mM LIT RA M E IM D M Re M ERE Md E d 8 3292 8 JDIPSSWITHGES ei oe eive to tee t otis tote C dc LES UE 9 DES NT TT 9 3 7 2 Address selection As db PE EORR Ne Seen ese ee hip s Ee ra 9 3 7 3 Channel selection I ble s eds 9 4 S
4. NFORMITY tn Accordence with 89 336 EEC Directive I the Europeen Council of 37 May 1989 on the opproximation of the laws of the Member ates relating of electromagnetic compatiblity SATEL HUNK 100 200 200 SATEL C LINK SATEL MINI LINK SATEL MINI LINK User Manual Version 1 0 WARRANTY AND SAFETY INSTRUCTIONS Read these safety instructions carefully before using the product Warranty will be void if the product is used in any way which is in contradiction with the instructions given in this manual or if the housing of the radio modem has been opened or tampered with The radio modem is to be used only on frequencies allocated by local authorities and without exceeding the given maximum allowed output power ratings SATEL is not responsible if any products manufactured by it are used in unlawful ways The devices mentioned in this manual are to be used only according to the instructions described in this manual Faultless and safe operation of the devices can be guaranteed only if the transport storage operation and handling of the devices are appropriate This also applies to the maintenance of the products To prevent damage both the radio modem and any terminal devices must always be switched O FF before connecting or disconnecting the serial connection cable It should be ascertained that different devices used have the same ground potential Before connecting any power cables the output voltage of the power supply shou
5. O PERA TIO ON PT PRR LOE ORY We ORG PO San PCR SEE See LTE Py Le 11 AE POINTS TO POINT us ORE PNE SER ob ROME SN POR GRE nia pine LU 11 4 1 1 Updating Digital tnessauas ar are e eere ed Pe Pes Feed 11 4 1 2 Start of the Pointto Point ODOFalOEE sus oca io ua roma EURO 11 4 2 POINT TO M Henne hnen hne nne 11 4 2 1 Start of the Multipoint operation 11 5 FACTORY SETTING ded aa aea ana dete rove abies deed ane de 12 b CONNECTION EXAMPLES es eet tne paced hri rati demos ie en Rats 13 T ACCESSORIES S ober Ed ee DIM MEMINI RIA e 14 SATEL MINI LINK User Manual Version 1 0 IMPORTANT NOTICE All rights to this manual are owned solely by SATEL O Y later called also SATEL All rights reserved The copying of this manual without the written permission from the owner of the rights by printing copying recording or by any other means or the full or partial translation of the manual to any other language including all programming languages using any electrical mechanical magnetic optical manual or other methods or devices is forbidden SATEL reserves the right to change the technical specifications or functions of its products or to discontinue the manufacture of any of its products or to discontinue the support of any of
6. RESS CHANNEL DE SM 7 DE Delayed alarm o Immediate Delayed Alarm In case of a failure in the transmission the alarm output response can be selected from immediate alarm to 10 seconds delayed alarm 8 SM SafeMode o Unchanged output state Safe Mode state In case a failure in transmission the outputs can be set to remain their status unchanged or change to Safe Mode which will switch all outputs to O FF position Safe Mode timing follows the setting of the switch 7 DE so it can be immediate or delayed by 10 seconds Selection table of the Dip switches 7 and 8 7DE 8SM 0 0 Immediate Alarm No Safe Mode 0 1 Immediate Alarm Immediate Safe Mode 1 0 Alarm delayed by 10 seconds No Safe Mode 1 1 Alarm delayed by 10 seconds Safe Mode delayed by 10 seconds 6 Selecting of the transmission standard According to the European standard for free channel operation the ratio of the transmission cycle must not be more than 10 90 This is active when the DIP switch number 6 is 0 In position 1 the cycle is faster Selection table of the DIP switch number 6 0 one transmission cycle per second 1 3 transmission cycles per second 10 SATEL MINI LINK User Manual Version 1 0 4 OPERATION The peration mode is selected using the PRTC L switch The operations are Point to Point or Point to M ultipoint In Point to Point operation mode the system consists of one pair of units The inputs of the unit are transmitted as out
7. ing currentis max 30 mA 3 3 OUT e OUT is internally connected to VDC through an automatic fuse The supply voltage for other devices e Connections can be taken from the O UT 3 4 Digital Inputs 11 12 and Outputs O1 O2 e Inputs o 2 pcs Activated with VDC A transmission is made always when there is a change in the input P to P Minimum Voltage for 1 state triggering is 7 Vdc e Outputs o 2 pcs pen relay contacts Max rating 9 30 VDC 1 A load 3 5 Pulse Input Can be used only in Point to M ultipoint mode e For fast pulses Maximum frequency is 10 kHz 3 6 Indicators e ON o Power O N OFF Illuminated when VCD is connected Blinking if the device is not working e 01 02 PO1 o Showing the status of the input and output Illuminated when the consequently pin is activated e ALARM o Illuminated if a fail in transmission has occurred If the MINI LINK has not received confirmation to the sent message it will repeat transmission Three fails in turn switches the AL O UT and the alarm LED O N e 1 12 PI1 PI2 o Showing the status of the Input Illuminated when the consequently pin is activated SATEL M IN I LIN K User Manual Version 1 0 3 7 DIP Swithces 3 7 1DIP switches 8 pcs 1 MP Protocol switch 1 2 M for Point to M ultipoint M aster Slave operation 0 P for Point to Point operation Point to Multipoint operation mode 2 3 4 5 ADDRESS Used in Poi
8. its products without any written announcement and urges its customers to ensure that the information at their disposal is valid SATEL software and programs are delivered as is The manufacturer does not grant any kind of warranty including guarantees on saleability and guarantees pertaining to applicability to a certain application Under no circumstances is the manufacturer or the developer of a program responsible for any possible damages caused by the use of a program The names of the programs as well as all copyrights relating to the programs are the sole property of SATEL Any transfer licensing to a third party leasing renting transportation copying editing translating modifying into another programming language or reverse engineering for any intent is forbidden without the written consent of SATEL SATEL PRO DUCTS HAVE NOT BEEN DESIGNED INTENDED NOR INSPECTED TO BE USED IN ANY LIFE SUPPO RT RELATED DEVICE OR SYSTEM RELATED FUNCTION NORASA PART OF ANY OTHER CRITICAL SYSTEM AND ARE GRANTED NO FUNCTIONAL WARRANTY IF THEY ARE USED IN ANY OF THE APPLICATIONS MENTIONED SATEL MIN I LIN K User Manual Version 1 0 PRODUCT CONFORMITY SATEL MIN I LINK Hereby SATEL O y declares that SATEL MIN I LIN K converters are in compliance with the essential requirements and other relevant provisions of Directive 89 336 EEC Therefore the equipment is labelled with the following C E marking 0523Q SATEL DECLARATION of CO
9. ld be checked Salo Finland 2005 SATEL MIN I LIN K User Manual Version 1 0 1 GENERAL 1 1 SATEL MINI LINK Pulse Counter and I O converter The SATEL MIN I LIN K is a Point to Point or Point to M ultipoint transparent I O converter with a pulse counter input The device works together with SATELLIN E 1870 radio modems In Point to Point transmission the digital status information can be sent through the radio modem to output in the other end In Point to M ultipoint mode itis also possible to read information from pulse transponders Point to M ultipoint transmission is possible adopting software suitable for the SATEL M IN I LIN K MINI LINK I O CONVERTER Screw connectors from left to right 1 minus 3 9 30 VDC 4 OUT 5 ALOUT 6 7 11 12 8 10 kHz 9 12 01 02 Indicators ON ALARM I1 12 01 02 P1 DIP Switches 8 pcs 1 PRTCL Protocol 2 3 4 5 P to P 2 3 4 5 P to MP 6 7 DE 8 SM MIN I LIN K ground Supply Voltage outfor other devices Alarm output Digital inputs Pulse Input Digital outputs from internal relay contacts Power ON OFF Failure in transmission device Digital inputs Digital outputs Pulse counter input O P to P 1 Point to Multipoint ADDRESS 15 CHANNEL 10 channels Transmission cycle 0 once second by European standard 1 3 times second Alarm Delay 1 0 OFF Safe Mode 1 ON 0 OFF SATEL MINI LINK User Manual
10. nt to M ultipoint operation to set channel for the sub station M aximum number of addresses is 15 3 7 2 Address selection table DIP2345 DIP2345 0 0 0 0z reserved for the Main Station 00012 address 1 00102 address 2 0011 address 3 01002 address 4 0 10 1 address 5 0 1 1 0 address 6 0 1 1 1 address 7 1000 address 8 1001 2 address 9 101 0 address10 101 1 address 11 110 0 address 12 1101 2 address 13 111 0 address 14 1111 address 15 Point to Point operation mode 2 3 4 5 CHANNEL Used in Point to Point operation to select change the operational channel When the power is turned O N the MINI LINK reads the channel information from the DIP switches Default mode setting is 0 0 0 0 12 up 02 down The channel can be changed by turning firstthe power O FF and then by setting the DIP switches channel selector to selected channel position for example 1 0 0 0 3 7 3 Channel selection table DIP2345 0 0 0 02 disable channel selection is notin use 000 12ch1 0010 ch2 0011 ch3 0100 ch4 0101 ch5 0110 ch6 0111 7 1000 ch8 1001 ch9 1010 ch10 SATEL MINI LINK User Manual Version 1 0 NO TE1 Check that both M IN I LIN Ks are set to the same channel before turning the power ON New channel is activated when the power is turned O N NO TE2 The MINI LINK unit will not operate with these settings 1011 1100 1101 1110 or 1111 The power ON indicator starts to blink in case any of these settings has been chosen ADD
11. puts of the other unit In Multipoint mode the main station controls the sub stations 4 1 Point to Point Point to Point operation is between two units The inputs of the unit are transmitted as outputs of the other unit 4 1 1 Updating Digital messages Digital information relay switch etc will be sent to the other unit always when there is a change at the input 4 1 2 Start of the Point to Point operation e Connect SATELLIN E 1870 radio modem to MINI LINK directly to its connector and check that it is locked e The MP switch must be 0 in the P to P position e Before connecting the device to a power supply connect first all inputs and outputs that are to be used e When both units have these basic settings the supply voltage can be connected e Check that the channel switches 2 3 4 5 0000 unless they are purposely selected for a specific channel for example 2 3 4 52 0101 2 channel 5 see chapter 3 7 channel selection table ZEE 4 2 Point to Multipoint In this mode the program at the main station controls the units of the sub stations The main station can drive one or more sub stations maximum 15 pcs system 4 2 1 Start of the Multipoint operation Connect one SATELLIN E radio modem to the CO M Port of the PC Connect the MIN I LIN K slave s to the SATELLIN E 1870 radio modems The M P switch must be 1 in the P to M P position Before connecting the device to a power supply connect first
12. rate a Multipoint system with a PC Layout of the SATELLINK PC Pro Multipoint program Satel I Link PC Pre 1 15 01 DEMO MODE Ele Mate Config Window bep nj slalo Tare unii demo reset 58 56 Comm Pat 1 Comm Por 2 ri 4 oles Comes Port 6 Comm Port 7 Comm Pos 8 cons UE me cow m E Digital Input 1 output 2 Digital Input 2 Counter Input 1 Tick Digital Input 1 Digital Input 2 D Counter Input 1 Tick output 2 Digital Input output 2 Counter Input 1 Tick 14
Download Pdf Manuals
Related Search