SMA BLUETOOTH REPEATER OUTDOOR
Contents
1. Device for Closing Dead Zones with SMA Bluetooth Wireless Technology SMA BLUETOOTH REPEATER OUTDOOR Installation Manual BTREPOUTlAcen 11 98 0054411 Version 1 1 Cn SMA Solar Technology AG Table of Contents Table of Contents Information on this Document ooooooooo 5 2 Safe aia oi adds 7 2 1 e ti E e CEA a e eO 7 2 2 Qualification of Skilled Persons 0 2 0 0 0 cee eee eee eee 8 2 3 Safety Prebdullons v cusan ae cueva ene eee Wee CBE p Pe rea 8 3 Scope of Delivery e mex like COR ERU ed ae Ra 9 3 1 Order Option Top Hat Rail Power Supply Unit o 9 3 2 Order Option Power Module fae eek cse eee Feet exe 10 3 3 Identifying the SMA Bluetooth Repeater Outdoor 10 4 Product Descrip a id 11 AAS Ranger USE aci 11 4 2 A RA 11 43 Device Overview lese ee 12 5 Assembly dec Ra ier A 15 5 1 Selecting the Mounting Location llle 15 5 2 Mounting the Bluetooth Repeater Outdoor on the Wall 18 6 Electrical Connectl ris ii eros ve Eveaxi t eg EeY ES 19 6 1 Connecting the Bluetooth Repeater Outdoor with Top Hat Rail Power Supply Unit to the Voltage Supply 0oooooo o 19 6 2 Connecting the Bluetooth Repeater Outdoor to the Voltage Supply 21 7 Settings 5 A A ete REI ERE EE 23 Zl Selling he MODE soccer rienda 23 TZ Setting NED coord ts eter ts dl la 23 8 Maintenance and Care lee 25 9 Decommissioning2. Pull out the wires of the cable Remove the cable from the enclosure To do this unscrew the nut from the lower left corner of the cable gland of the enclosure and pull out the cable gland from the enclosure Reattach the enclosure lid using the enclosure lid screws 9 2 Packing the Bluetooth Repeater Outdoor Pack the Bluetooth Repeater Outdoor using the original packaging or packaging that is suitable for the weight and size of the Bluetooth Repeater Outdoor see Section 11 Technical Data page 32 9 3 Disposing of the SMA Bluetooth Repeater 26 Dispose of the Bluetooth Repeater Outdoor in accordance with the locally applicable disposal regulations for electronic waste or Send the Bluetooth Repeater Outdoor back to SMA Solar Technology AG with shipping paid by sender When doing so label the packaging ZUR ENTSORGUNG FOR DISPOSAL BTREPOUT IA en 1 1 Installation Manual SMA Solar Technology AG 10 Troubleshooting 10 1 Voltage Supply 10 1 1 LED RDY The LED RDY is only visible when the enclosure lid is open 10 Troubleshooting In order to open the enclosure lid loosen the four enclosure lid screws Status permanently glowing green Meaning The supply voltage is good Bluetooth Repeater Outdoor is in operation Measure None flashes green and all other LEDs are switched off Power supply is marginal Bluetooth Repeater Outdoor is in operation If you are using t
3. Default setting The device can connectto a maximum oftwo communication products The device cannot connect to other inverters or SMA Bluetooth Repeaters 2 9 andA F Bluetooth is switched on The device can interlink with all SMA Bluetooth products with the same NetID See Section 10 2 for information on the status of the Bluetooth LEDs Installation Manual BTREPOUT lA en 1 1 23 7 Settings SMA Solar Technology AG i NetID 1 is possible for plants with 1 inverter You may leave the default NetID set to 1 in your inverter if your Bluetooth plant consists of the following products A maximum of one inverter A maximum of one computer with Bluetooth and the Sunny Explorer software A maximum of one Sunny Beam of type BEAM BT 11 GR1 or A maximum of one inverter A maximum of 2 Sunny Beams of type BEAM BT 11 GR1 In all other cases you must determine a free NetID see Sunny Explorer Help 1 If you do not know the plant NetID read off the NetID from one of the devices in the plant see the manual of the device 2 Remove the seal insert of the screw seal from the top of the enclosure of the Bluetooth Repeater Outdoor with a screwdriver 2 5 mm Thus you can see the NetID rotary switch and the Bluetooth LEDs in the inside of the enclosure 3 Use a screwdriver 2 5 mm to turn the arrow of the NetID rotary switch to the plant NetID 4 Insert the seal insert of the screw seal and tighten it using a screwdri
4. esee nnn nn 26 9 1 Detaching the Bluetooth Repeater From The Wall 26 9 2 Packing the Bluetooth Repeater Outdoor 0 00000 ee 26 9 3 Disposing of the SMA Bluetooth Repeater 205 26 Installation Manual BTREPOUT lA en 1 1 3 Table of Contents SMA Solar Technology AG 10 Troubleshooting 5 1 ore rt eere 27 IO T Voltage Supply cs e tgvtb etes Evo uet Peace nese see VE 27 TOIT PED DN eso he che a 27 10 1 2 LEDs of the Top Hat Rail Power Supply Unit 29 10 2 Connection Quality us diari ride 30 11 Technical Data E A EE SEES EE 32 LEC OMA AAA 34 4 BTREPOUT lA en 1 1 Installation Manual SMA Solar Technology AG Information on this Document 1 Information on this Document Validity This document is valid for the following device types as of hardware version A1 and firmware version V 1 07 R BIREP DOUT GRI BTREP OUT GR2 Target Group This document is for skilled persons Only qualified personnel with the appropriate skills are allowed to perform the tasks described in this manual see Section 2 2 Qualification of Skilled Persons page 8 Additional Information Links to additional information can be found at www SMA Solar com Document title Document type SMA Bluetooth Wireless Technology Technical description SMA Bluetooth Wireless Technology in Practice Technical information Symbols Symbol Explanation A DANGER Indicates
5. 28 BTREPOUT IA en 1 1 Installation Manual SMA Solar Technology AG 10 Troubleshooting 10 1 2 LEDs of the Top Hat Rail Power Supply Unit The LEDs of the top hat rail power supply unit are only visible when the enclosure lid is opened In order to open the enclosure lid loosen loosen the four enclosure lid screws Status Meaning Measure The LED The supply voltage is good None DC OK is Bluetooth Repeater Outdoor is glowing green in operation and the LED DC LO is switched off The LED DC The supply voltage is too low Check whether the socket outlet is supplying OK is The Bluetooth Repeater voltage switched off Outdoor is not in operation Do this for example by connecting a and the LED different device to the socket outlet DC LO is m If the socket outlet is providing voltage glowing then either the top hat rail er suppl valle en ei op power supply unit or the Bluetooth Repeater Outdoor is defective Contact the SMA Service Line Both LEDs are switched off No supply voltage The Bluetooth Repeater Outdoor is not in operation Check whether the socket outlet is supplying voltage Do this for example by connecting a different device to the socketoutlet If the socket outlet is providing voltage then either the top hat rail power supply unit or the Bluetooth Repeater Outdoor is defective Contact the SMA Service Line Installation Manual BTREPOUT lA
6. Overvoltage category Voltage Supply via the Power Module Input voltage 12V 24 V AC DC Tolerance value for input voltage 2076 Typical power consumption 0 6 W Maximum power consumption 1 5 W Environmental Conditions in Operation Ambient temperature 25 C 60 C Relative humidity non condensing A 100 Altitude above mean sea level MSL Om 2 000 m 32 BTREPOUT 1A en 1 1 Installation Manual SMA Solar Technology AG Ambient Conditions for Storage Transport 11 Technical Data Ambient temperature 40 C 70 C Relative humidity non condensing 10 95 Altitude above mean sea level MSL Om 2 000 m Communication Inverter Bluetooth Data logger Bluetooth Range in open air lt 100m Installation Manual BTREPOUT lA en 1 1 33 12 Contact 12 Contact SMA Solar Technology AG If you have technical problems concerning our products please contact the SMA Service Line We require the following information in order to provide you with the necessary assistance Type serial number and firmware version of the inverter Serial number of the communication product Firmware version or software version of the communication product Serial number and firmware version of the Bluetooth Repeater Outdoor SMA Solar Technology AG Sonnenallee 1 34266 Niestetal Germany www SMA de SMA Service L
7. The seal must not protrude over the cable gland 8 HandHighten the nut to the cable gland Tighten the nut with a torque of 0 8 Nm thus securing the cable 9 Reattach the enclosure lid using the enclosure lid screws 22 BTREPOUT 1A en 1 1 Installation Manual SMA Solar Technology AG 7 Settings 7 Settings 7 1 Setting the MODE The MODE rotary switch is set to the position O for delivery Other positions are not permitted and are intended for SMA Service only If the MODE rotary switch is not positioned correctly set the correct position Remove the seal insert of the screw seal from the top of the Bluetooth Repeater Outdoor using a screwdriver 2 5 mm Thus you can see the MODE rotary switch in the inside of the enclosure and reach it using the screwdriver 2 5 mm Turn the arrow of the MODE rotary switch to the correct position using a screwdriver 2 5 mm Insert the seal insert of the screw seal and tighten it using a screwdriver 2 5 mm This ensures the degree of protection IP54 7 2 Setting the NetID The NetID serves to distinguish PV plants with SMA Bluetooth operating in close proximity to one another All devices in a PV plant must have the same NetID You can set the SMA Bluetooth Repeater Outdoor to the NetID of your plant using the NetID rotary switch Assignment of the rotary switch positions NetID Function 0 Bluetooth is switched off 1 Bluetooth is switched on
8. en 1 1 29 10 Tr oubleshooting 10 2 Connection Quality The Bluetooth Repeater Outdoor can only display the connection quality if it is integrated into an existing SMA Bluetooth network The SMA Bluetooth network can only be established by a master Devices will always display the connection signal to the device from which the connection has been established SMA Solar Technology AG Bluetooth LEDs 00x Two LEDs are permanently lit Status Meaning Measure blue LED yellow LEDs 000 Connection quality very None good permanently 3 LEDs are lit permanently lit Connection quality good None OXXx One LED is permanently lit Connection quality is unreliable XXX Three LEDs off Connection quality critical Change the position of the Bluetooth Repeater Outdoor or Install additional Bluetooth Repeater Outdoor devices 30 Master is a network engineering term In a network a master is a device that for example requests other devices slaves to receive or send data All communication products e g Sunny Explorer Sunny Beam with Bluetooth are masters in an SMA Bluetooth network BTREPOUT IA en 1 1 Installation Manual SMA Solar Technology AG 10 Troubleshooting Bluetooth LEDs Status Meaning Measure blue LED yellow LEDs x XXX The Bluetooth Repeater Check the NetlD Outdoor is not connected to Ch h
9. 3 1 Order Option Top Hat Rail Power Supply Unit Check the scope of delivery for completeness and any externally visible damage Contact your specialist dealer if the scope of delivery is incomplete or damaged A B A A Figure 1 Components included in the scope of delivery with order option top hat rail power supply unit ltem Quantity Description A 1 Bluetooth Repeater Outdoor device type BTREP OUT GR 1 pre assembled B 4 Screw C 4 Wall plug Installation Manual BTREPOUT lA en 1 1 9 3 Scope of Delivery SMA Solar Technology AG 3 2 Order Option Power Module Check the scope of delivery for completeness and any externally visible damage Contact your specialist dealer if the scope of delivery is incomplete or damaged A Figure 2 Components included in the scope of delivery with order option Power Module ltem Quantity Description A 1 Bluetooth Repeater Outdoor device type BTREP OUT GR2 pre assembled B 1 Power Module for the voltage supply for scope of delivery see the installation manual of the Power Module Screw D 4 Wall plug 3 3 Identifying the SMA Bluetooth Repeater Outdoor You can identify the SMA Bluetooth Repeater Outdoor by means of the type label The type label is on the righthand side of the SMA Bluetooth Repeater Outdoor 10 BTREPOUT 1A en 1 1 Installation Manual SMA Solar Technology AG 4 Product Description 4 Produc
10. ED SMA Solar Technology AG Sonnenallee 1 34266 Niestetal Germany Tel 49 561 9522 0 Fax 49 561 9522 100 www SMA de E Mail info SMA de 2004 to 2012 SMA Solar Technology AG All rights reserved Installation Manual BTREPOUT lA en 1 1 35 SMA Solar Technology SMA Solar Technology AG www SMA de SMA Australia Pty Ltd www SMA Australia com au SMA Benelux bvba sprl www SMA Benelux com SMA Beijing Commercial Company Ltd www SMA China com cn SMA Central 8 Eastern Europe s r o www SMA Czech com SMA France S A S www SMA France com SMA Hellas AE www SMA Hellas com SMA Ib rica Tecnolog a Solar S L U www SMA Iberica com SMA Solar India Pvt Ltd www SMA India com SMA Italia S r l www SMA ltalia com SMA Japan K K www SMA Japan com SMA Technology Korea Co Ltd www SMA Korea com SMA Middle East LLC www SMA Me com SMA Portugal Niestetal Services Unipessoal Lda www SMA Portugal com SMA Solar Thailand Co Ltd www SMA Thailand com SMA Solar UK Ltd www SMA UK com CE
11. Repeater only included in order option top hat rail power supply unit i Do not damage or remove the self adhesive membrane The self adhesive membrane is a pressure membrane balance element e g for heat generation in the inside of the enclosure and ensures the tightness of the enclosure in accordance with the degree of protection IP54 according to IEC 60529 12 BTREPOUT 1A en 1 1 Installation Manual SMA Solar Technology AG 4 Product Description Figure 5 Overview of the device elements on the Bluetooth Repeater Outdoor Item Description Colour Explanation A Terminal DC source top hat rail power supply unit or Power Modul B RDY Green LED for voltage supply C MODE z Rotary switch for configuring the MODE D NetID Rotary switch for configuring the NetID E Blue Bluetooth LED F Yellow Bluetooth LEDs Figure 6 Overview of the LEDs of the top hat rail power supply unit Item Description Colour Explanation A DC LO Yellow LED for voltage supply B DC OK Green LED for voltage supply Installation Manual BTREPOUT IA en 1 1 13 A Product Description on mme gt On EOE Figure 7 Overview of the terminals on the feed through terminal SMA Solar Technology AG ltem Description A Terminal 1 for the connection of the voltage supply cable B Terminal 2 for the connection of the voltag
12. a hazardous situation which if not avoided will result in death or serious injury A WARNING Indicates a hazardous situation which if not avoided could result in death or serious injury A CAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE Indicates a situation which if not avoided could result in property damage Information that is important for a specific topic or goal but is not safety relevant Indicates an essential requirement for achieving a specific goal Desired result xalo p A problem that might occur Installation Manual BTREPOUT lA en 1 1 5 1 Information on this Document SMA Solar Technology AG Typographies Typography Usage Example bold Display messages The value can be read Elements of a user interface from the Energy field e Connections Select Settings Eleme nts ta be s lecied e Enter the value 10 in the Minutes field e Elements to be entered gt e Connects several elements that Select Settings gt Date are to be selected Button Key Button or key to be selected or Select Next pressed Nomenclature PV plant Complete designation Plant Designation in this document Small wind turbine system Plant SMA Bluetooth Piggy Back Bluetooth Piggy Back SMA Bluetooth Piggy Back Plus Bluetooth Piggy Back Plus SMA Bluetooth Repeat
13. e supply cable BTREPOUT IA en 1 1 Installation Manual SMA Solar Technology AG 5 Assembly 5 Assembly 5 1 Selecting the Mounting Location Requirements for the mounting location L1 If the top hat rail power supply is used the mounting location must be in the vicinity of a socket outlet in the interior area Ll The mounting location must be protected against dust moisture and corrosive substances Observe the maximum cable length L1 Ifa Power Module is used observe the maximum cable length of 10 m for the voltage supply cable Observe minimum clearances lt 240 mm gt A i i 400 mm 710 mm _ i 1 20 mm 20 mm E mm d ee ei EU RN i Figure 8 Minimum clearances to be observed Observe the minimum clearance to walls and other devices or objects Observe the minimum clearance of 1 m to devices using the 2 4 GHz frequency band e g WLAN devices or microwave ovens This is to prevent any reduction in connection quality or data transmission speed Installation Manual BTREPOUT lA en 1 1 15 5 Assembly SMA Solar Technology AG Determining the Mounting Location Determine the mounting location by varying the distance between the Bluetooth Repeater Outdoor and devices with a critical connection signal until all devices display at least a good signal Requirements Ll The rotary switch MODE is at position O see Section 7 1 Setting the MODE page 23 O The rotary switch NetID is set
14. er Outdoor Bluetooth Repeater Outdoor Sunny Beam with Bluetooth Wireless Technology Sunny Beam with Bluetooth Abbreviations Abbreviation Designation Explanation AC Alternating Current DC Direct Current LED Light Emitting Diode WLAN Wireless Local Area Network 6 BTREPOUT lA en 1 1 Installation Manual SMA Solar Technology AG 2 Safety 2 Safety 2 1 Intended Use The Bluetooth Repeater Outdoor is used in outdoor installations to close dead zones under unfavourable installation conditions between SMA Solar Technology AG devices by means of Bluetooth or to improve poor wireless connections The Bluetooth Repeater Outdoor is intended for private and industrial use Use the Bluetooth Repeater Outdoor in outdoor installations The SMA Bluetooth Repeater Outdoor may only be used with supported products For safety reasons it is not permitted to modify the product or install components that are not explicitly recommended or distributed by SMA Solar Technology AG for this product The enclosed documentation is an integral part of this product e Read and observe the documentation Keep the documentation in a convenient place for future reference Only use the SMA Bluetooth Repeater Outdoor in accordance with the information provided in the enclosed documentation Any other use may result in personal injury or property damage Supported Products The SMA Bluetooth Repeater Outdoor ma
15. he top hat rail power supply unit Contact the SMA Service Line If you are using the Power Module If you are using the cable included in the delivery Contact the SMA Service Line If you are using a different cable Improve the power supply via one of the following measures Shorten the cable Choose a larger cable cross section flashes green and all other LEDs are flashing The Bluetooth Repeater Outdoor firmware is defective Contact the SMA Service Line Installation Manual BTREPOUT lA en 1 1 27 10 Troubleshooting SMA Solar Technology AG Status off Meaning No power supply or the power supply is too low The Bluetooth Repeater Outdoor is not in operation Measure If you are using the top hat rail power supply unit Check whether the socket outlet is supplying voltage e Do this for example by connecting a different device to the socketoutlet If the socket outlet is providing voltage then either the top hat rail power supply unit or the Bluetooth Repeater Outdoor is defective Contact the SMA Service Line If you are using the Power Module e Ifyou are using the cable included in the delivery Contact the SMA Service Line If you are using a different cable Check the wiring If the wiring is correct either the Power Module or the Bluetooth Repeater Outdoor is defective Contact the SMA Service Line
16. ine Inverters 49 561 9522 1499 Communication 49 561 9522 2499 Fax 49 561 9522 4699 E Mail ServiceLine SMA de 34 BTREPOUT lA en 1 1 Installation Manual SMA Solar Technology AG Legal Provisions Legal Provisions The information contained in this document is the property of SMA Solar Technology AG Publishing its content either partially or in full requires the written permission of SMA Solar Technology AG Any internal company copying of the document for the purposes of evaluating the product or its correct implementation is allowed and does not require permission Declaration of Conformity SMA Solar Technology AG hereby declares that the described device devices fulfill the essential requirements and other relevant rules of Directive 1999 5 EC The entire Declaration of Conformity can be found at www SMA de SMA Factory Warranty The current warranty conditions come enclosed with your device These are also available online at www SMA Solar com and can be downloaded and are available on paper from the usual sales channels if required Trademarks All trademarks are recognized even if these are not marked separately Missing designations do not mean that a product or brand is not a registered trademark The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by SMA Solar Technology AG is under licence QR Code is a registered trademark of DENSO WAVE INCORPORAT
17. inverter from any voltage sources on the AC and DC sides see inverter installation manual Observe the waiting time to allow the capacitors to discharge Requirement O The Power Module is installed in the inverter see Power Module installation manual 1 Loosen the enclosure lid screws and remove the enclosure lid from the Bluetooth Repeater Outdoor 2 Unscrew the nut from the lower left corner of the cable gland of the enclosure and push the filler plug out of the nut 3 Preparing the cable AM Remove 40 mm of the cable sheath from the i side of the Bluetooth Repeater Outdoor 4 Shorten unused insulated wires flush with the Omm Oriri cable sheath Strip approx 10 mm off the wires Installation Manual BTREPOUT lA en 1 1 21 6 Electrical Connection SMA Solar Technology AG 4 Insert the cable into the enclosure through the nut and the cable gland 5 Connecting the cable to the feed through terminal in the inside of the enclosure Push the terminal 1 and terminal 2 of the feed through terminal open using a screwdriver 2 5 mm Connect the wires of the cable to terminal 1 and terminal 2 The polarity is arbitrary 6 Recommission the inverter with installed Power Module see inverter manual M LED RDY is glowing green X The LED RDY is off or flashing Rectify the fault see Section 10 1 Voltage Supply page 27 7 Checkthat the cable gland seal is correctly in place
18. ion point from the alternating current grid using the separator Thus you ensure that there is no voltage present at the AC grid connection point Connect the Bluetooth Repeater Outdoor to the voltage supply Plug the grid connection plug into the socket outlet if a grid connection plug is used f no grid connection plug is used connect the other end of the cable to the voltage supply as desired e g via a cable junction box Connect the AC grid connection point to the AC grid using the separator M LED DC OK of the top hat rail power supply unit and LED RDY of the Bluetooth Repeater Outdoor are glowing green X LED DC LO ofthe top hat rail power supply unit or LED RDY are not in operation or are glowing yellow Rectify the fault see Section 10 1 Voltage Supply page 27 BTREPOUT 1A en 1 1 Installation Manual SMA Solar Technology AG 6 Electrical Connection 9 Check whether the cable gland seal is correctly in place The seal must not protrude over the cable gland 10 Hand tighten the nut to the cable gland Tighten the nut with a torque of 0 8 Nm thus securing the cable 11 Reattach the enclosure lid using the enclosure lid screws 6 2 Connecting the Bluetooth Repeater Outdoor to the Voltage Supply A DANGER Danger to life due to electric shock when opening the inverter Lethal voltages are present in the conductive parts of the inverter e Prior to performing any work on the inverter disconnect the
19. lled holes in the enclosure on the wall 4 Drill the holes at the marked positions 5 Attach the Bluetooth Repeater Outdoor to the wall using wall plugs and screws 6 Remove the seals from the inside of the enclosure lid and press them onto screws 7 Reattach the enclosure lid using the enclosure lid screws 18 BTREPOUT 1A en 1 1 Installation Manual SMA Solar Technology AG 6 Electrical Connection 6 Electrical Connection 6 1 Connecting the Bluetooth Repeater Outdoor with Top Hat Rail Power Supply Unit to the Voltage Supply A DANGER Danger to life due to electric shock in the event of missing separators and missing fuses on the AC cable e The AC cable used for the connection must have a separator Inthe case of an alternating current supply by means of an IT system the separator must have two poles in accordance with IEC 60364 1 e The separator must be easily accessible e Ifthe separator is a plug connection the socket outlet must be situated in close proximity to the Bluetooth Repeater Outdoor e The AC cable used for the connection must be equipped with a fuse 16 A for Europe and 20 A for the US and Canada A DANGER Danger to life due to electric shock in the event of mixing up the Bluetooth Repeater Outdoor Only the Bluetooth Repeater Outdoor of the device type BTREP OUT GR1 is allowed to be connected via the top hat rail power supply unit fo the alternating current grid e Ensure that the Bl
20. nt of the Bluetooth Repeater Outdoor Product Bluetooth Repeater Outdoor Good connection quality One blue and two yellow LEDs are lit Sunny Boy of the type SB xOOOTL 2x and SB xx00HF 30 Sunny Tripower of the type STP xx000TL 10 At least two rings are shown in the inverter display e ITN Other types of SMA inverters with Bluetooth Piggy Back or Bluetooth Piggy Back Plus Use the communication product to check whether the connection signal is improved by using the Bluetooth Repeater Outdoor see manual of the communication product Communication product See manual of the communication product The connection quality displayed is at least good for all devices Mount the Bluetooth Repeater Outdoor there at this location X The connection quality displayed is not at least good for all devices Move the Bluetooth Repeater Outdoor to another position and check the connection signals again If necessary install additional SMA Bluetooth Repeater Outdoor devices Installation Manual BTREPOUT lA en 1 1 5 Assembly SMA Solar Technology AG 5 2 Mounting the Bluetooth Repeater Outdoor on the Wall Requirement O Bluetooth Repeater Outdoor must be disconnected 1 Loosen the screws of the enclosure lid and remove the lid 2 Drill holes through the indentation in the enclosure edges Use a drill bit 4 mm for this purpose 3 Mark the holes with the help of the pre dri
21. onoliki off Three LEDs off ange he position or the the Bluetooth network Bluetooth Repeater Outdoor There is no device with the or install additional same NetlD within the radio Bluetooth Repeater Outdoor range devices The SMA Bluetooth network Commission a master in the has not been established SMA Bluetooth network Only masters e g communication products initiate network establishment ecc The NetID rotary switch is Set the NetID rotary switch uu set to position 1 or O to the NetlD of your plant Three LEDs are see Section 7 2 flashing e 606 The Bluetooth Repeater Contact the SMA Service EUM dub Outdoor firmware is Line is flashing Three LEDs are defective and RDY flashing LED is flashing green Installation Manual BTREPOUT lA en 1 1 31 11 Technical Data 11 Technical Data General Data SMA Solar Technology AG Width x height x depth 200 mm x 160 mm x 93 mm Weight with top hat rail power supply unit 800 g Weight with Power Modul 740g Mounting location outdoors Type of mounting Wall mounting Status display LEDs Degree of protection IP54 Certified countries All EU Member States according to IEC 60529 Voltage Supply via Top Hat Rail Power Supply Unit Input voltage 100 V 240 V AC Tolerance value for input voltage 1076 Frequency of input voltage 47 Hz 63 Hz Typical power consumption 1 8 W Maximum power consumption 2 5 W
22. t Description 4 1 Range of Usage Figure 3 Use of the Bluetooth Repeater Outdoor example The Bluetooth Repeater is used in outdoor installations to close dead zones under unfavourable installation conditions between SMA Solar Technology AG devices with Bluetooth or to improve poor wireless connections Item Description A Inverter with Bluetooth B Bluetooth Repeater Outdoor C Communication device with Bluetooth 4 2 Functions Connection to SMA devices with Bluetooth via Bluetooth Class 1 Maximum range of up to 100 min free field conditions with direct visual contact Can be used outdoors thanks to weatherproof enclosure Installation Manual BTREPOUT lA en 1 1 11 4 Product Description SMA Solar Technology AG 4 3 Device Overview i 7 y Figure 4 Overview of the enclosure elements with enclosure lid left hand and enclosure bottom righthand ltem Description A Seal B Enclosure lid screw C Top hat rail power supply unit D Feed through terminal for the connection to the voltage supply E Enclosure opening for voltage supply F Opening with sel adhesive membrane for pressure equalisation G Screw seal with screwable seal insert by means of which there is access to the rotary switches MODE and NetID H Bluetooth
23. to the NetID of the plant see Section 7 2 Setting the NetID page 23 A DANGER Danger to life due to electric shock when opening the inverter Lethal voltages are present in the conductive parts of the inverter e Prior to performing any work on the inverter disconnect the inverter from any voltage sources on the AC and DC sides see inverter installation manual Observe the waiting time to allow the capacitors to discharge 1 Decommission the plant see the manual of the inverter and of the communication product Thus you ensure that the Bluetooth Repeater Outdoor is integrated into the SMA Bluetooth network at the point where the dead zone is thus improving the Bluetooth connection at that point 2 Position the Bluetooth Repeater Outdoor half way between the devices with critical connection quality 3 Connect the voltage supply see Section 6 Electrical Connection page 19 4 Recommission the plant see the installation manual of the inverter and of the communication product 5 Repeat the plant search with the communication device see the communication product manual e g Sunny Beam with Bluetooth Sunny Explorer 16 BTREPOUT IA en 1 1 Installation Manual SMA Solar Technology AG 5 Assembly 6 Check that the connection quality for all devices is at least good During this procedure all devices must be in their usual positions e g the Sunny Beam with Bluetooth must not be held directly in fro
24. uetooth Repeater Outdoor is of device type BTREP OUT GR1 before connecting it to the alternating current grid To do so check the type label on the Bluetooth Repeater Outdoor see Section 3 3 Identifying the SMA Bluetooth Repeater Outdoor page 10 Requirements for the connection cable O Number of insulated wires 2 Cable cross section 1 mm 2 5 mm External diameter 5 mm 10 mm Cable must be suitable for outdoor installations Cable must be UV resistant pqodod If a grid connection plug is used in outdoor installations Grid connection plug must be suitable for outdoor installations Installation Manual BTREPOUT lA en 1 1 19 6 Electrical Connection SMA Solar Technology AG 20 Loosen the screws of the enclosure lid and remove the lid Unscrew the nut from the lower left corner of the cable gland and push out the filler plug Preparing the cable Remove 40 mm of the cable sheath from the K side of the Bluetooth Repeater Outdoor 40mm 10mm Shorten unused insulated wires flush with the cable sheath Strip approx 10 mm off the wires Insert the cable into the enclosure through the nut and the cable gland Connecting the cable to the feed through terminal in the enclosure Push the terminal 1 and terminal 2 of the feed through terminal open using a screwdriver 2 5 mm Connect the conductor to terminal 1 and the insulator to terminal 2 Separate the AC grid connect
25. ument and all safety precautions 2 3 Safety Precautions Electric Shock Lethal voltages are present in the conductive parts of the inverter e Prior to performing any work on the inverter disconnect the inverter from any voltage sources on the AC and DC sides see inverter installation manual Observe the waiting time to allow the capacitors to discharge Burn Hazards Some parts of the inverter enclosure can get hot during operation e During operation touch the inverter on the enclosure lid only Environmental Influences When closed the Bluetooth Repeater Outdoor has the degree of protection IP54 The Bluetooth Repeater Outdoor is thus protected against dust intrusion and water penetration Dust intrusion and water penetration can damage the Bluetooth Repeater Outdoor When the enclosure of the Bluetooth Repeater Outdoor is not closed protect the Bluetooth Repeater Outdoor against dust intrusion and water penetration Close the enclosure of the Bluetooth Repeater Outdoor again after performing any work on the Bluetooth Repeater Outdoor Electrostatic Discharge By touching electronic components you can damage or even destroy the inverter or the Bluetooth Repeater Outdoor through electrostatic discharge ESD e Earth yourself before touching any components of the inverter or the Bluetooth Repeater Outdoor 8 BTREPOUT lA en 1 1 Installation Manual SMA Solar Technology AG 3 Scope of Delivery 3 Scope of Delivery
26. ver 2 5 mm This ensures the degree of protection IP54 24 BTREPOUT 1A en 1 1 Installation Manual SMA Solar Technology AG 8 Maintenance and Care 8 Maintenance and Care Check the Bluetooth Repeater Outdoor regularly for external damage or soiling e f external damage to the Bluetooth Repeater Outdoor is severe enough to impair correct function replace the Bluetooth Repeater Outdoor If the Bluetooth Repeater Outdoor is soiled clean the Bluetooth Repeater Outdoor using only a slightly damp cloth Any cleaning agents used must be non abrasive and non corrosive Installation Manual BTREPOUT lA en 1 1 25 9 Decommissioning SMA Solar Technology AG 9 9 1 1 6 Decommissioning Detaching the Bluetooth Repeater From The Wall When connecting to the AC grid separate the Bluetooth Repeater Outdoor from the voltage supply using the separator and check that there is no voltage present in the cable When a grid connection plug is used remove it from the socketoutlet Remove the cable gland of the Power Module for the connection to the Power Module see installation manual of the Power Module Loosen the screws of the enclosure lid and remove the lid Remove the screws of the enclosure from the wall and take down the Bluetooth Repeater Outdoor Remove the cable from the feed through terminal in the inside of the enclosure Push open terminal 1 and terminal 2 of the feed through terminal using a screwdriver 2 5 mm
27. y only be used with the following SMA Solar Technology AG products e All SMA communication products with Bluetooth All inverters with SMA Bluetooth Piggy Back upgrade A list of supported inverters can be found in the SMA Bluetooth Piggy Back installation manual All inverters with SMA Bluetooth Piggy Back Plus upgrade A list of supported inverters can be found in the SMA Bluetooth Piggy Back installation manual e SMA PV inverters with integrated Bluetooth SB Sunny Boy 3000TL 20 SB 4000TL 20 SB 5000TL 20 from software package 2 06 SB 3000TL 21 SB 4000TL 21 SB 5000TL21 SB 2000HF 30 SB 2500HF 30 SB 3000HF 30 STP Sunny Tripower 10000TL 10 STP 12000TL 10 STP 15000TL 10 STP 17000TL 10 SMA wind power inverters with integrated Bluetooth WB Windy Boy 3600TL 20 WB5000TL 20 WB 2000HF WB 2500HF WB 3000HF Installation Manual BTREPOUT lA en 1 1 7 2 Safety SMA Solar Technology AG 2 2 Qualification of Skilled Persons The work described in this document must be performed by skilled persons only Skilled persons must have the following qualifications Training in the installation and commissioning of electrical devices and plants Knowledge of how to deal with the dangers and risks associated with the installation and operation of electrical devices and plants Knowledge of all applicable standards and directives Knowledge of how an inverter works and is operated Knowledge of and adherence to this doc
Download Pdf Manuals
Related Search