gj d emerald mk3 lighting controller installation manual
Contents
1. GJD BASE 2 ZONE 1 MAINS SUPPLY LOAD ZONE 2 12VDC CONNECTIONS DUAL CABLE SINGLE CABLE CLAMPING CLAMPING one ee ee ee Low voltage connections Cable 4 6 core 7 0 2mm OPTIONAL PIEZO SOUNDER _ oy i amma Aux OR r RELAY DIODE 12VDC 50mA MAX __BLACK S BLUE OPTIONAL BLUE r el BUTTON BLUE Z pen i Greed irene YELLOWS a i BLUE pay TUT BLUE a 7 eae e YELLOW S N aoe ETETE i S p s ete ma cal Le me es fo FS 1 2 3 1 2 3 ZONE 1 ZONE 2 GJD DETECTORS GJD DETECTORS 1 Link both lighting areas together except in walk test connect LINK to 2 Remote triggering of lights for the timer period Pulse Count 1 must be selected 3 Activate zone lighting for alarm period when linked to an intruder alarm panel All diodes IN4148 IN4002 etc2. panel 10 5 The factory settings are shown STD 22420 39s 8s 10 te 0 le 30 1 Ley 24 9 3 AUX LIGHT ON PULSE TIME SECS TIME MINS COUNT AUX AUXILIARY OUTPUT 50mA maximum OFF Internal sounder and auxiliary output disabled STD Internal sounder and auxiliary output active and will emit a warning tone on each detection when the tone button is selected 10 30 The auxiliary output time after last detection seconds The internal sounder is as the STD LIGHT ON TIME IN MINUTES 1 to 24 The length of the light on time after last detection during darkness minutes The red detector indicators will stay on for this time after the last detection day and night PULSE COUNT A Walk test Select this symbol to assist in location alignment of the detector beams during daylight installations When the detector beams are activated the external lights will stay on for a period of 6 seconds lL 003 After completing the walk test function set the pulse count to the required level The pulse count is the number of detector beams that have to be crossed to trigger the system 1 will give a fast response 2 gives better immunity with good response 3 gives highest immunity to false activations in poor environments but is less responsive CAUTION To BE INSTALLED BY QUALIFIED PERSONNEL ONLY Mains voltage connections emat a oe ee Cable 1 5mm flat twin earth se ha G aiii SLEEVED EARTH CABLES PLUG TYPE FUSE
3. GJD EMERALD MK3 LIGHTING CONTROLLER INSTALLATION MANUAL Part No GJDO10 THe GJD EMERALD IS A DUAL AREA me SECURITY LIGHTING CONTROLLER WHICH ENABLES EXTERNAL AREAS TO BE ACCURATELY MONITORED GJD EMERALD MK3 IT AUTOMATICALLY SWITCHES UP TO 3000 WATTS OF LIGHTING AT NIGHT FOR A PRE SET PERIOD AND CAN BE MANUALLY OVERRIDDEN WHEN REQUIRED THE CONTROLLER INCORPORATES AN AUDIBLE WARNING TONE AND FEATURES SIX DETECTOR INDICATORS WHICH ILLUMINATE WHEN ACTIVATED BY DETECTION DAY AND NIGHT SPECIFICATION SUPPLY 230Vac 50Hz via ELCB MCB unit fused at 13A 12VDC 100mA for GJD Opal XL 6mA or Elite Detectors 10mA Optional external 12VDC piezo sounder upto 50mA INDICATION Six 24 hour detector indicators which pulse during detection and are steady after detection for the duration of the light on timer setting AUDIBLE Internal warning tone which sounds on detection day and night and is button selectable It has a steady tone for zone one and a pulsed tone for zone two CONTROL Controls upto 12 x GJD detectors Switches two independent areas of lighting with manual override when required OPTIONS Ability to link both lighting areas together Ability to have a timed auxiliary output Ability to activate lighting when linked to an intruder alarm panel DIMENSIONS 146 W x 86 H x 56 D mm Weight 507gm MOUNTING Indoor use only Mount in a clean dry location on a secure flat surface TEMPERATURE 10 TO 55 Centigrade E Self
4. contained Class 2 independently mounted control i OPERATING INSTRUCTIONS When a detector is activated day or night the relevant detector indicator flickers and will remain on for the length of the timer setting During darkness the lighting will be switched on automatically while the detector is receiving activation signals and will automatically turn off after the preset timer period The Zonel and Zone 2 green indicator have to be selected for automatically controlled lighting on detection during darkness Green indicator is on This mode must be selected on both zones for automatic lighting during darkness Green indicator flashing A detector has activated the lighting for a zone Manually selecting this yellow indicator will turn the lighting on for both zones Turning the indicator off will return to automatic mode Indicator off Yellow indicator flashing A detection has automatically activated a lighting zone Red indicator on Audible warning tone selected Zone 1 and or Zone 2 indicator to be selected to function Indicator off Audible warning tone is switched off for both zones ADJUSTMENT TO FACTORY SETTINGS When connecting the unit to the electrical supply or when the supply is interrupted the indicators will flash for one minute whilst the system settles Pressing any button during this time will start normal operation Internal adjustments
Download Pdf Manuals
Related Search