X20033 Infresco IR 4kW Installation Manual
Contents
1. EARTH SUPPLY GABLE SIZE 1 5mm min Typical Load 2 x AKW Infra red Heater Lamps TEMPERATURE SENSOR INPUT PIR SENSOR ip OR ENABLE INPUT HEATER LAMP CABLE SIZE 0 75mm min ziii INFRARED HEATER LAMP ziii INFRARED HEATER LAMP Specifications Infresco Main Unit Mains Voltage Max load at 20 ambient Power Consumption PIR Set Time Period Temperature Set point Factory Set Temperature trip point IP Rating Gland Diameter 2 Lamp Installation Operating Temperature IP Rating Max Unit Operating Temperature Dimensions PIR Movement Sensor optional Operating Voltage Direction Detect Outdoor Temperature Sensor optional Dimensions WARNING 230Vac 10 50 Hz 4 kW 50mA 5 Minutes 5S to 25T 20C 65 Max Cable Entry 2 5mm Must be fitted in Parallel 20T to 30 IP65 65 W 280mm D 200mm H 80mm D inclusive of Glands 12V dc 90 Adjustable 18 Metres W 115mm D 110mm H 55mm It is important that the Infresco IR is not mounted directly to any flammable material i e wood It is recommended that the heatsink be spaced off any the mounting wall using pillars to aid in heat dissipation It is recommended that installation and maintenance of this equipment should be done with reference to the current edition of the E E wiring regulations BS7671 by suitably qualified trained personnel These regulations contain important requirements regarding safety of electrical2. INTRODUCTION The Infresco has been designed specifically to work with Infra Red Heaters with a rating of 4kW it will allow you to control a variety of heating and lighting solution The Infresco has a 1 to 10 step setting allowing you to find the optimum comfort setting in you specific area With energy saving a major factor in the design brief once the Infresco is switched on it will automatically manage the heating system With a built in temperature sensor only allowing the unit to switch on when required and a PIR that will detects a requirement for the heater to switch on only when needed An optional remote control allows for the unit to be fitted out of the way so safety is paramount The Infresco has a built in soft start function which will add up to an additional 30 life to your heater lamp APPLICATIONS Any application were high inrush current is an issue or control is required Typical use is for Infra Red Heating lamps Garden lighting FEATURES Soft Start up to 30 extended life of Lamp Variable Control Ability to find comfort level Simple Installation Ability to plug directly in 13A Plug with up to 3kW load Energy Saving Automated system Only heat when required Temperature Monitoring If ambient temperature is above preset the Infresco unit remains switched off SAFETY FIRST Please read these instructions before installing and operating this product See warning for additional information Installati
3. equipment for International Standards refer to I E C directive IEC950 UNITED AUTOMATION UNITED AUTOMATION LIMITED 1 Southport Business Park Kew Southport PR8 4HQ ENGLAND Tel 0044 0 1704 516500 Main Tel 0044 0 1704 516516 Sales Fax 0044 0 1704 516501 Enquiry united automation com INFRESCO Installation amp Users Manual 4kW IR Control RoHS Compliant Directive 2002 95 EC UNITED AUTOMATION X20033 Issue 1 03 11 08
4. on The ideal site for the PIR to be mounted is approximately 2 5 Meters of the floor Ceiling mounting is preferred but not essential The PIR must not be mounted Directly in line of the lamps output e Highly reflective surfaces Radiators or other thermostatically controlled heaters e Open door ways with people walking past Commissioning NOTE On switch on the PIR takes 60 seconds to set before detection takes place NOTE The PIR continues to monitor the area and will reset to the set time every time it detects movement Before testing ensure the wiring is correct The temperature trip point has already been preset at the factory The timer is preset to 5 minutes The expected detection area can now be walked tested using the diagram shown in mind The area should be crossed in various directions to ensure coverage is as expected Display Features Display shows t The Infresco is turned OFF as the ambient temperature is above the trip level set by TEMP SET Display shows F The Infresco is set to FULL output Display decimal point pulses The PIR input is waiting to be enabled i e no movement Display decimal point fully on The Infresco is in Standby mode pressing the remote control POWER button will toggle the power ON and OFF You can check the remote control is transmitting by observing the decimal point flashing rapidly INSTALLATION CIRCUIT H MAINS LOAD SUPPLY MASIMUM dhii LVE a NEUTRAL
Download Pdf Manuals
Related Search