6 Inch Speed Dome Installation Manual
Contents
1. Step4 Install dome to the mount Feed the cables through the opening on top of the back box and attach the dome to the mount and finally use M3 screws to secure the dome Refer to Section 7 2 for installation instructions Note Follow the same instructions described above for the Short arm Corner Mount installation For outdoor applications please adopt the water proof measures The Short arm Wall Mount is not recommended for outdoor applications 6 Inch Speed Dome Installation Manual V2 0 0 Chapter 6 Pendant Mounting Applications 6 1 Mounting Components eo Mounting Base Applicable to pendant domes with the use of the pendant pole and pole adapter o Pendant Pole E Pendant Adapter 6 Inch Speed Dome Installation Manual V2 0 0 6 2 Pendant Mounting Instructions The pendant mounting is applicable to the indoor outdoor solid ceiling construction which should comply with the following mounting requirements The ceiling must be thick enough to mount the expansion screws The ceiling must be capable of supporting up to 8 times the total load of the dome and its accessories Do ll m E Step1 Install the mounting base Drill four 96 holes in the ceiling according to the fastener holes locations of the mounting base and then insert M6 expansion screws not supplied into the holes Pull the power2. NE Py QUE SE y D Zz A A WY Ay SE OLA NS ae ENTER PESO o SS AA 4 br l Ss FE Hi 3 Ly L fe ES S p y E y Goy y y Ly Hex Screws M830 and Spring Washers 5 2 Pole Mounting Instructions The pole mounting is applicable to the indoor outdoor solid pole construction which should comply with the following mounting requirements The diameter of pole must be constituent with the mounting dimensions of the stainless steel straps The pole construction must be capable of supporting up to 8 times the total load of the dome and its accessories 6 Inch Speed Dome Installation Manual V2 0 0 Step1 Assemble the pole mount adapter Use a screwdriver to loosen the three stainless steel straps and then insert them through the rectangle holes on the pole adapter Step2 Install pole adapter Feed the control line video cable and power cable through the central opening and secure the three stainless steel straps to the pole and finally use the screwdriver to fasten the screws at the steel straps Note For outdoor applications please adopt the water proof measures 6 Inch Speed Dome Installation Manual V2 0 0 Step3 Install wall mount assembly Screw four hex screws with the spring washers to the pole adapter through the wall mount and gasket ees a
3. WM 1 d _ A 4A D2 Stud f l o p f N lA Ac fg gm 2 E A AT Stud k A Ka bo ly Y alt Ll r VT a 6 Inch Speed Dome Installation Manual V2 0 0 2 2 Short arm Wall Mount P 1 a KA i 7 Funny Mm bo 2 3 Corner Adapter N ES D H 3Stud 6 Inch Speed Dome Installation Manual V2 0 0 2 4 Pole Adapter DE Studi i 4 942 6 Inch Speed Dome Installation Manual V2 0 0 Chapter 3 Wall Mounting Applications 3 1 Mounting Components o Wall Mount Applicable to indoor outdoor pendant domes e a Pal f EL O r i af i D ji AS A EN D my gt AN 3 AY MA E U A o Mounting Accessories Nuts and Flat Washers 3 2 Wall Mounting Instructions The wall mounting is applicable to the indoor outdoor solid wall construction which
4. I LA I I I L El x i Xx I i SA A A Sc T ba H Sa s a f r I TE o T S lt lt ii I I I Corner Adapter For use with the wall mount in the corner mounting applications E Mounting Accessories L Hex Screws M830 Nuts Spring Washers and Flat Washers 6 Inch Speed Dome Installation Manual V2 0 0 4 2 Corner Mounting Instructions The corner mounting is applicable to the indoor outdoor 90 solid corner construction which should comply with the following mounting reguirements The wall must be thick enough to install the expansion screws The wall must be capable of supporting up to 8 times the total load of the dome and its accessories 1 1 Step1 Install the corner adapter Drill four holes in the corner according to the mounting locations and then insert M6 expansion screws not supplied into the holes Pull the power cord video cable and control line through the opening of the corner adapter Secure the corner adapter to the corner by using nuts and washers to tighten the four expansion screws Note Make sure the cables have enough length For outdoor applications please apply the sealant around the cable opening to prevent water y Step2 Secure the wall mount to the corner Apply four hex screws with the spring washers t
5. Network High definition Speed Dome 3 Configure the dome address baud rate and other settings through DIP switch SW1 and SW2 located on the bottom board of the dome as shown in Figure 1 2 2 Please refer to Section 1 4 DIP Switch Settings for setting address baud rate communication 6 Inch Speed Dome Installation Manual V2 0 0 protocol etc SW1 ADDRESS SW2 Baud Rate Settings SW2 Protocol Settings Protocol Self adaptive Switch Number 1 2 3 Switch Number 4 5 6 a00 sad off off Ae eee oi oo off Switch1 Number 1 2 I 2 64 128 9600 Baud on on Switch Value 1 16 3 4 6 4 3 32 syd WM off off off off of off off off PREP iin lcm off off fy on on on Rx Address N off off off off off off Off TE INN ENCOUN off fru Rx Address 255 Of Of on on on ON ON on R3485 Mode Settings Termination Settings Switch Number 7 Switch Number Simplex off Not Terminated off Half Duplex on Terminated ON Figure 1 2 12 Address and Protocol Settings Key lock Figurel 2 13 DIP Switch Location on Side of Dome Drive 4 Install the back box Open the interconnect board of the back box and feed the cables through the top of the back box from the mount and connect to the back board circuit board Attach the back box to the mount and tighten the set screws see Figurel 2 14 to secure the back box Connect all wiring and replace the interconnect board Note For outdoor applications please apply the thread compound and the
6. Speed Dome Installation Manual V2 0 0 SW 1 Address SW Baad Rate Setting SW Publ Setting Protocol Self adaptive Sello Niumba Wr oe 2400 Baud ONTAN om lot low wichi Nbe 1 273 4 5 6 7 8 i R R Dr on Sater TL 4 Le i ai i H O E4 ja FAA E ae Ra Broadcast Am O EDIT OMA AE 1920 Pa Adi 1 OM Ful RI i 23 OM On i I 8200 Baud HAE 38400 Baud ae id On On or 7 PS Moda Ba S nt Numer Such fener E AmA Hall Dapa lema OM E a 1 in DIP Switch 2 Protocol DIP Switch 2 3 Wiring Connector 4 Address and Protocol Settings Figure 1 2 2 Bottom Board of Dome Drive 4 Loosen the captive screw on the interconnect board of back box and lift the hinged door to the circuit board as shown in Figure 1 2 3 Unplug the video cable power cord and other cables terminals to avoid cables twisting during the back box installation The circuit board of dome is shown in Figure 1 2 3 And refer to Figure 1 2 4 high speed dome and Figure 1 2 5 network high speed dome for the wiring terminals I Captive Screw 2 Wiring Connector 3 Lock Clips Figure 1 2 3 Back Box Interconnect Board 6 Inch Speed Dome Installation Manual V2 0 0 OUTI OUT2 GND IN7 ING INS IN4 INS IN2 INI XY XY ONDA LINDA ON ON 2 NC NC VOUT VGND Rx Rx O NO INI ZNI ENI YNI GNI ONI NI OND eno ACISS 1 Alarm In Out Terminals 7 inputs 2outputs 2 Video Out and RS 485 COM Terminals 3 24VAC Voltage Input and GND Te
7. YN ee gt 3 P Va X A yn eee ff if rs Se S fo ae A E N i __ j fil ji jj A Y NN rd hb S Push the in ceiling mounting base into the mounting hole in the ceiling and use the screwdriver to tighten the set screws which will automatically compress the ceiling and secure the mounting base Step4 Install the dome drive Take out the dome drive from the packing case and check whether the drive has any damages or abnormal conditions Set the baud rate control protocol and address of the dome by referring to the Operation Installation Manual of Speed Dome And push the dome drive to onto the mounting base and secure it in position Note If future packing and transportation is required or the dome drive needs to be returned to the manufacturer for repair due to failure occurrence during the operation please use the original packing materials to pack the dome drive When the dome drive has been properly installed please apply power to the unit and check whether its power up self test action performs normally 6 Inch Speed Dome Installation Manual V2 0 0 guided pole 8CT W Step5 Install the bubble and trim ring Attach the lower dome with the bubble to the dome drive and swivel in clockwise direction to secure the bubble in place Place the trim
8. open up the dome cover avoid direct contact with the dome cover because the acidic sweat of the fingers may erode the surface coating of the dome cover 7 Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover not to use alkaline detergents 6 Inch Speed Dome Installation Manual V2 0 0 Preparation for Installation 1 Basic requirements 1 All the electronic operation should be strict compliance with the local electrical safety regulations fire prevention regulations and other related regulations at the installation place 2 Check whether all the accessories are there according to the packing list make sure that the place and installation mode are conform to the demands if not please contact the supplier 3 Please use this product according to the working environment 2 Check installation space Make sure the place have enough space to install the speed domes and its accessories 3 _ Check the intensity of conformation at the installation scene Please make sure that the endure ability of ceilings or walls is 4 times as the weight of speed dome and its accessories 4 Preparation of cables e Choose the video cable according to the transmission length The video should meet the least demands as l 75O resistance 2 100 copper core conducting wire 3 95 weaving copper shield Oo RS485 communication cable please refer to Appendix 2 24V AC power cable please refer to Appendix 3 5 Please keep a
9. the set screws to secure the bubble 6 Inch Speed Dome Installation Manual V2 0 0 Figure 1 2 18 Install Bubble ts WL UG Figure 1 2 19 Tighten the Set Screws 1 3 Initial Settings Address code 0 Baud rate 2400 1209 terminator OFF 6 Inch Speed Dome Installation Manual V2 0 0 1 4 DIP Switch Settings 1 4 1 High Speed Dome DIP Switch Settings SW1 Address SW2 Baud Rate Settings SW2 Probcal Settings Protocol Self adaptive ST I YAWEI 7TH 4 5 6 2400 Bawd 0N Mini off off loft Swiichi Number 1 23456 7 8 Y L On Mii al Switch Value UTA 816264128 9600 Bad On OR Id of Ee hon es a A R of of of lof lof lof lof off IRE i off lofty On on on Pr Adi 1 off of lof lof lof loft off 35400 Baud OnFJOn RA Ads 25 ON ON ON ON OM ON ON ON R65 Mode Setings Switch Nunder j Switch Nunber 8 Simplex off 0 Half Duplex on Terminated ON Figure 1 4 2 Bottom Board of Dome Drive 1 Address DIP Switch 2 Protocol DIP Switch 3 Wiring Connector 4 Address and Protocol Settings The dome provides two DIP switches SW and SW2 for setting the dome address baud rate protocol etc As shown in Figure 1 4 2 ON 1 OFF 0 In SW1 and SW2 1 is the lowest position and 8 is the highest position Please refer to the following list for specific settings Note As the high speed dome is capable of being self adaptive to PELCO D PELCO P HIK Code VICON and KALATEL 32 protocols and the network speed dome is self adaptive to Pel
10. 6 Inch Speed Dome Installation Manual V2 0 0 2010 01 6 Inch Speed Dome Installation Manual V2 0 0 Thank you for purchasing our product If there is any guestion or reguest please do not hesitate to contact dealer This manual is applicable to 6 Inch Speed Dome This manual may contain several technically incorrect places or printing errors and the content is subject to change without notice The updates will be added into the new version of this manual We will readily improve or update the products or procedures described in the manual 6 Inch Speed Dome Installation Manual V2 0 0 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Neglecting any of the warnings may cause serious injury or death Cautions Neglecting any of the cautions may cause injury or eguipment damage Warnings Follow these safeguards to prevent serious Cautions Follow these precautions to injury or death prevent potential injury or material damage Warnings 1 In the use of the product you must be strict compliance with the electrical safety regulations of the nation and region 2 Please use the power adapter which is provided by normal company The standard of the power adapter is AC24V 3A 3 Do not connect several devices to one power adapter as adapter overload may ca
11. Connections arsin e n E EE AAA AAA A AAA AAA 21 Chapter 2 Mounis DIMAS iio cae GOR 22 AAA A 22 22 noe arm Wall Motta iii 23 ZO COMA ido za 23 LEPO NA A A YN FN FAN A RR FAN WR A Y RR Y A YN UN NS RH Y HY ben 24 2 Pendan AUS SV ae ene Re eee E O AN GO SD OO COD RTR 24 Chapter Wall Moun ano Applications seson do RA os 25 3 1 Mounting Components A GYD A DN IOG DAER 25 3 2 Wall Mount las tU Se i aod GG Nd rela Go iU rele let ded rete CR UC Unn 25 Chapter 4 Corner Mounting Application Peesecweied bend ricino 28 Al INI OTTO COMPONEN S sansad I GN OA RA A A O KSSS RAA O GO GOD 28 A 2 Corer Mountine Gis true tions bi 29 Chapter Pole Mounn APP ICE OTIS ea i O Gwd a OG CGA a tack CDE GN 31 Aaa RE HR HWRE HARI HF HR FYTH RF HA EN HAN EF HAN EY UN OF HN OHAN AA AR SRA SNR 31 A Mounting Haistuc IOnse A A eat ace act NO 32 Chapter 6 Pendant Mounting Applications ssserssrrrsrrrsrsrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr rss rss rss rss rr RR RR RR RER nn nro nro nono nn nn RR RR RR rr rn nn 35 O UN Tonn no COMPAS dde 35 6 2 Pendant Mounino TOS CH HOS title 36 Chapter 7 In ceiline Mountine AmpplcaHonse en eu a OO 38 Pcl Installaton C ONIONS i Y a ba UO sis DN DN A AO OLEU OS DOS EN AGOE ODIAD AO GAEAF 38 7 2 Ameo ie NT Gun amo TS BEC OB Sc GCR dere CR o Od fr s UC GN Ro NC Go BONC Go COD AH del 38 Appendix Lightning amp uree PEC Mii anna O iD A sd GR GR CND A GR o o FAR SR 43 Appendix 2 R5493 Bus Connection aes un ue O aes ace al O ace a
12. co P Pelco D and HIK Code protocols as well no DIP switch settings for control protocol are reguired 6 Inch Speed Dome Installation Manual V2 0 0 1 4 2 Medium Speed Dome and Network High definition Speed Dome DIP Switch Settings 1 SWI Address DIP Switch 2 SW2 Protocol DIP Switch Figurel 4 3 DIP Switch Location on Side of Dome Drive The dome provides two DIP switches SW and SW2 for setting the dome address baud rate protocol etc As shown in Figure 1 4 2 ON 1 OFF 0 In SW1 and SW2 1 is the lowest position and 8 is the highest position Please refer to the following list for specific settings Note As the medium speed dome and the network medium speed dome are capable of being self adaptive to PELCO D PELCO P and HIK Code protocols no DIP switch settings for control protocol are reguired 1 4 3 Address Settings The DIP Switch SW1 is used for setting the dome address Dome Address swiss r e a s e r a Settings for address 0 71 are listed as below 6 Inch Speed Dome Installation Manual V2 0 0 Address o ore ore or ore or or ore or 71 ox ort ore or orr ore orr orr ore on on or or orr or or e forr orr ore on ort ore orr orr o on ort ore on ort ore orr orr o Torr ow on OFF orr ON OFF OFF 9 os on on or or ox fom orr 6 Inch Speed Dome Installation Manual V2 0 0 a Tos ore ore ov or T os om Torr ON OFF OFF eo omor on
13. cord video cable and control line through the opening at the mounting base Secure the mounting base to the corner by using nuts and washers to tighten the four expansion screws Note Make sure the cables have enough length For outdoor applications please apply water proof measures between the ceiling surface and mounting base and around the cables opening The pendant mounting application is not recommended for outdoor environment where directly suffers rain 6 Inch Speed Dome Installation Manual V2 0 0 Step2 Install the pendant pole Swivel the pendant adapter into the matching pendant pole and then use the retainer screws to secure the two parts Pull out the cables through the pendant pole and screw the pendant pole into the mounting base and use the set screws to secure the two parts as well Note For outdoor applications please apply the water proof thread compound to the threads Step3 Install dome to the mount Feed the cables through the opening on top of the back box and attach the dome to the pendant pole and finally use M3 screws to secure the dome Refer to Section 1 2 for installation instructions Note In case of insufficient ceiling height directly attach the dome to the mounting base without use of pendant pole as shown in the figure right above 6 Inch Speed Dome Installation Manual V2 0 0 Chapter 7 In ceiling Mount
14. damp proof stopper to threads of the back box and the mount 6 Inch Speed Dome Installation Manual V2 0 0 m ce _ rr ea Damp proof Stopper A S L Thread Tape Wu Set Screw Figure 1 2 14 Attach Back Box to Mount Install the dome drive Push the two tabs on both sides of the dome drive and line up the AMP connectors to insert the dome 5 drive into the back box by following the guided pillar Continue pushing on the both ends of the tabs until both sides click firmly into place Wtf da ITA NN A NY I o TT gt MAM Figure 1 2 15 Install Dome Drive 6 Inch Speed Dome Installation Manual V2 0 0 Guided Pillar AMPConnector Bottom Board and Set Screws Figure 1 2 16 AMP Connector and Guided Pillar on Interconnect Board AMP Connector Guided Arc Figure 1 2 17 AMP Connector and Guided Arc on Dome Drive Bottom Board 6 Install the bubble by aligning the two grooves see Figure 1 2 18 on the trim ring of the bubble with the two set screws see Figure 1 2 19 on the back box and then fasten
15. e communication method of dome to simplex or half duplex DIP Switch SW2 Simplex Half duplex Settings 6 Inch Speed Dome Installation Manual V2 0 0 1 4 8 Terminating Resistor Settings The position 8 of DIP Switch SW2 is used for setting the terminating resistor of dome DIP Switch SW2 Terminating Resistor Settings Not Terminated 1 5 Alarm In Out Connections Note The Medium Speed Dome have no alarm inputs and alarm outputs The high speed dome can be connected with 7 alarm inputs 0 12VDC and 2 alarm outputs and the network high speed dome is allowed to connect with 2 alarm inputs 0 12VDC and 2 alarm outputs and the network medium speed dome and the HD network speed dome is allowed to connect with 1 alarm inputs 0 12VDC and 1 alarm outputs Refer to the following diagram O JQG 3FG GND OUT Relay 12VDC 10 A 250VAC 220V AC Diagram left Diagram right The alarm provides the relay output no voltage and the external power supply is required when it connects to the alarm device For DC power supply left diagram the input voltage must be within the range of 12VDC 30mA For AC power supply the external relay must be used right diagram so as to prevent damages to the unit and avoid risk of electric shock 6 Inch Speed Dome Installation Manual V2 0 0 Chapter 2 Mounts Dimension 2 1 Long arm Wall Mount boi
16. ic Address 25 OM OM OM On OM on OM On EE SS o RAS Mode Settings Switch Number 7 switch Number 8 Simplex off Half Duplex On Terminated ON 4 Problems in the Practical Application Normally users adopt star shape connection method in construction under this situation the terminal resistors must be connected between two farthest devices as Figure 4 1 and 15 but this connection method is not satisfy the requirement of the RS485 industry standard so that it will lead to some problems such as signal reflection anti jamming ability decline when the devices are faraway At this time the dome will be uncontrollable or self running etc y 4 A ya a n gre R Figure 4 For such case the best way is adding a RS485 distributor This product can effectively change the star shape connection to which satisfies the reguirement of RS485 industry standard in order to avoid those problems and improve the communication reliability Show as figure 5 6 Inch Speed Dome Installation Manual V2 0 0 RS485 Distributor Figure 5 1 FAQ of RS485 Bus Fault Phenomenon Probable Cause Solutions The speed 1 The address or Baud Rate is not matched 1 Adjust the address or Baud Rate of Host or Speed dome do the between Host and the Speed Dome Dome to make a match self check but 2 R5485 are connected incorrectly 2 Change the R54853 and R5485 wires can not be 3 Wiring drops 3 fastening the w
17. ing Applications 7 1 Installation Conditions The in ceiling mounting is applicable to the indoor ceiling construction which should comply with the following mounting requirements The height above the ceiling must be more than 250mm e The ceiling must be with the thickness of 5 40mm e The ceiling must be capable of supporting up to 5 times the total load of the dome and its accessories 7 2 In ceiling Mounting Instructions Step1 Drill holes in the ceiling Take out the drill drawing from the package and use it as a template to draw a circle on the ceiling and then cut out the circle Note The allowable tolerance of diameter is 2mm Drill Drawing 6 Inch Speed Dome Installation Manual V2 0 0 ss XK NY NN Step2 Connect cables Open the hinged door and feed the power cord video cable control line and network cable through the opening of the back box and then connect all wiring to corresponding sockets located on the circuit board After connections close the hinged door The red LED indicator will light when the power is applied to the unit Note Power off the unit after power up check of the dome is finished SCTCW Step3 Install the back box Firstly loosen the two set screws on both sides of the back box to make them lie in the location as shown in the following figure 6 Inch Speed Dome Installation Manual V2 0 0 w E A nr FR y lo y y SZ A p
18. ire controlled 4 R5485 wire broke 4 Change R5485 wire The speed 1 loose contact of R5455e 1 fastening R5485 wire dome can be 2 one R5485 wire broke 2 Change R5485 wire controlled but 3 Host and speed dome are too far awaye 3 Add terminal matched resistance not smoothly 4 Too many speed domes are connected 4 Add A5485 distributore 6 Inch Speed Dome Installation Manual V2 0 0 Appendix 3 24VAC Wire Gauge amp Transmission Distance The following table has described the recommended max distance adopted for the certain wire gauge when the 24VAC voltage loss rate is less than 10 For the AC driven device the maximum voltage loss rate allowable is 10 For example for a device with the rating power of 80VA which is installed at a distance of 35 feet 10m away from the transformer then the minimum wire gauge reguired is 0 8000mm Distance _ feet m Power vay 0 8000 1 000 250 Pres 000 e 451 137 716 1218 Ca ao oo av av Jan an 6 Inch Speed Dome Installation Manual V2 0 0 Appendix 4 Table of Wire Gauge Standards Bare g o e American Wire Gaae Cross sectional Area g British Standard Wire Gauge ofBaro Wire a Qu Cn gt Mo BO ho M Oo ao 05 Go Go E B BR gt ho on PO Go 00 M co M uj O 19 SWG
19. lation and wiring with lightning protection and grounding in mind should be combined with the lightning protection consideration of the building and conform to the related national standards and industry standards 6 The system should be eguipotentially grounded and the grounding equipment must satisfy double reguest of system anti Jamming and electric safety and it must not appear short circuit and open circuit with the zero conductor of strong grid When the system is grounding individual the resistance should be no more than 4Q the section al area of the grounding cable should be no less than 25mm For grounding instructions please refer to the Installation Manual of Speed Dome video arrester a E lightning rod comaunicate arrester porer arrester The speed dome should be in the range of 45 degrees under the lightning rod the resistance of earthing conductor should be saaller than 41 i steel jacket 6 Inch Speed Dome Installation Manual V2 0 0 Appendix 2 RS485 Bus Connection 1 General Property of RS485 Bus According to RS485 industry bus standard RS485 is a half duplex communication bus which has 1209 characteristic impendence the maximum load ability is 32 payloads including controller device and controlled device 2 RS485 Bus Transmission Distance When using 0 56mm 24AWG twisted pair line according to different baud rate the max transmission distance theory tab
20. le is shown as below 2400BPS 4800BPS 1200m The transmission distance will be decreased if we use the thinner cable or use this product under the strong electromagnetic interference situation or there are lots of devices are added to the bus on the contrary the transmission distance will be increased 3 Connection Method and Terminal Resistance 1 RS485 industry bus standard require daisy chain connection method between any devices both sides have to connect a 1200 terminal resistance show as Diagram 1 the simplified connection method is shown as diagram 2 but the distance of D should not be too long 1 2 3 AH 32H Diagram 2 2 Connection of 120Q terminal resistor The 120Q terminal resistor can be connected through the DIP switch on the communications board as high speed dome shown in Figure3 For a new dome the 120Q matching resistor is defaulted as unconnected switch on the eighth bit of SW2 it will be connected Conversely switch off the eighth bit of SW2 it will be unconnected 6 Inch Speed Dome Installation Manual V2 0 0 SW1 Address SW2 Baud Rate Settings SW Proloco Settings Protocol Self adaptive Switch Number 1 2 3 Swilch Number 4 5 6 2400 Baud OTIN off of off Swichi Numer 123 45 6 7 8 4800 Bad Emi iof Swichi Vai 1 2 4 8 16 3264 128 9600 Baud On On mi dn Address off loft off of lof off 19200 Bad Pion on on on Ri Address Of lof lof lof off lof off 35400 Basi onFiion F
21. lease refer to the related sections from Chapter2 to Chapter7 for specific installation methods of different mounts Open the bubble push the two clips on both sides of the dome drive towards the back box and then take off the dome drive Remove the expand aple poly ethylene and protective sticker from the dome drive Refer to Figure 1 2 9 Push the tab lock on the bottom interconnect board of back box and lift the hinged door to the circuit board as shown in Figure 1 2 9 Unplug the video cable power cord and other cables terminals to avoid cables twisting during the back box installation Refer to Figure 1 2 10 medium speed dome and Figurel 2 11 network speed dome and network high definition speed dome for the wiring terminals on back box circuit board 1 Lock Clips 2 Tab Lock 3 Wiring Connector Figure 1 2 9 Back Box Interconnect Board 6 Inch Speed Dome Installation Manual V2 0 0 NC1 NC2 VOUT VGND Rx Rx AC1 SS AC2 LON XN XY NOA LNOA Z N 1 Video Out and RS 485 COM Terminals 2 24VAC Voltage Input and GND Terminals Figure 1 2 10 Back Box Circuit Board Medium Speed Dome NC1 NC2 VOUT VGND Rx Rx MIC SPK GND IN1 OUT1 COM Go Xy XY ONDA LNOA GON LON AGT SAC 1 Video Out and RS 485 COM Terminals 2 Audio In Out Alarm In Out Terminals and GND 1 inputs 1 outputs 3 24VAC Voltage Input and GND Terminals Figure 1 2 11 Back Box Circuit Board Network Medium Speed Dome and
22. ll wrappers Please keep all wrappers after unpack them for future use In case of any failure occurred please return the speed dome to the factory with the original wrapper Note Transportation without the original wrapper may result in damage on the speed dome and cost additional charge 6 Inch Speed Dome Installation Manual V2 0 0 Table of Contents Table COMENS seat Seta etc Y AE EN AAA EFE NEF FED AA NRA SERA 4 Chapter Vi Mas Ta MAT 6 EF _ _ a en CN 6 MRS A Be ea is E n A AA E AN 6 Ez IAS TA MA LOTT de ies ii 6 1 2 1 High Speed Dome Installation 6 1 2 2 Medium Speed Dome and Network High definition Dome Installation 99 nenn 10 komaa l LO tg Gu APA uet Semper te ARS ONE asa 15 LADIS Witi SENIE S ols es wade endl dah ee hada h eet eho h eet eth eth eset ht et eth et eel eee eet 16 1 4 1 High Speed Dome DIP Switch Settidgs ooooccccccccnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnns 16 1 4 2 Medium Speed Dome and Network High definition Speed Dome DIP Switch Settings 17 1 4 3 TS UI FRY RY NIN A E N NF NN E R NE FN HN SF 17 1 4 4 Baud Rate Sc T DS I GN LD 20 1 4 5 Protocol Settings High Speed Dome se Re rss rss rss rss rr rr rn 20 1 4 6 Parity and Manchester Code Settings Medium Speed Dome amp Network Speed Dome 20 1 4 7 Simplex Hall duplex SENOS ta 20 1 4 8 TAO Resistor O do e 21 I S Alan tia In OUT
23. o es 44 Appendix 3 24VAC Wire Gauge amp Transmission Distance ococcccncnnnnnnnnonnnnonononnnnnnnnnnnnnnnnnnnnnnnnnn nono nn rnnnnnnnnnnnnnnnnns 47 6 Inch Speed Dome Installation Manual V2 0 0 Appendix 4 Table of Wire Gauge Standards 6 Inch Speed Dome Installation Manual V2 0 0 Chapter 1 Installation 1 1 Check Parts List Prior to installation unpack the dome unit and check whether it is in good condition and all parts and accessories are included by referring to the packing list Note The power supply for the speed dome is 24VAC 3A 1 2 Installation 1 2 1 High Speed Dome Installation Note The following installation instructions are applicable to both high speed dome and network speed dome models 1 Install the dome mount Please refer to the related sections from Chapter2 to Chapter7 for specific installation methods of different mounts 2 Open the bubble and remove the expand aple poly ethylene and protective sticker from the dome drive Refer to Figure 1 2 1 nia bL UT T DH rg Tu the ls n NO Mt yr HEL Figure 1 2 1 Open bubble and remove the expand aple poly ethylene and protective sticker from dome drive 3 Configure the dome address baud rate and other settings through DIP switch SW1 and SW2 located on the bottom board of the dome drive as shown in Figure 1 2 2 Please refer to Section 1 4 DIP Switch Settings for setting address baud rate communication protocol etc 6 Inch
24. o the corner adapter through the wall mount and gasket Note When tightening the screw 1t 1s better to compress the spring washer firstly and then rotate half a round so as to maintain required waterproof effect without damaging the threads 6 Inch Speed Dome Installation Manual V2 0 0 Step3 Install dome to the mount Feed the cables through the opening on top of the back box and attach the dome to the mount Finally use M3 screws to secure the two units Refer to Section 1 2 for installation instructions Note Follow the same instructions described above for the Short arm Corner Mount installation For outdoor applications please adopt the water proof measures The Short arm Wall Mount is not recommended for outdoor applications 6 Inch Speed Dome Installation Manual V2 0 0 Chapter 5 Pole Mounting Applications 5 1 Mounting Components o Wall Mount Applicable to indoor outdoor pendant domes with the use of corner adapter wall adapter or pole adapter eo Pole Adapter For use with the wall mount in the pole mounting applications 6 Inch Speed Dome Installation Manual V2 0 0 Stainless Steel Straps For use with the pole adapter with the following dimensions selectable 059 82mm p84 108mm 103 127mm 9130 152mm p155 178mm p180 203mm 9194 216mm Customized dimensions can also be provided according to user s demand o Mounting Accessories CA VAN
25. ox on ox orr orr es fore on or orr orr orr on orr a omor on or orr orr ON OFF Pe on or on or ore orr ON OFF w om on ow or ore orr on orr an 6 Inch Speed Dome Installation Manual V2 0 0 1 4 4 Baud Rate Settings The positions 1 3 of DIP Switch SW2 are used for setting the baud rate of dome respectively as 2400bps 4800bps 9600bps 19200bps and 38400bps For baud rate out of the above range the default setting is 2400bps Refer to the following table DIP Switch SW2 Baud Rate Settings 2 3 i Baud Rate Positionsl 3 Settings 1 4 5 Protocol Settings High Speed Dome The positions 4 6 of DIP Switch SW2 are used for setting the communication protocols of dome Refer to the following table network speed dome model does not support Manchester code protocol C Poo Posiionsa6 Sotings 4 5 6 Others 1 4 6 Parity and Manchester Code Settings Medium Speed Dome amp Network Speed Dome SW2 FFK 4 5 6 MAREA BETR Tue A AA BAT ES A ORT HR RH Jy NU CF AY BER AN SC FF SABIDO The positions 4 6 of DIP Switch SW2 are used for setting the parity and Manchester protocol of dome Refer to the following table network speed dome model does not support Manchester code protocol SW2 Parity and Manchester Code Settings Parity Manchester Positions 4 6 Settings None 1 4 7 Simplex Half duplex Settings The position 7 of DIP Switch SW2 is used for setting th
26. ring into the bubble by alinging its fastening holes with the the ball stud on the mounting base and finally tighten the two M3 screws to secure the lower dome Note In order to maintain clear video images do not touch the internal or outer part of the dome with your hands direcly or with other materials which will cause pollution to the dome 6 Inch Speed Dome Installation Manual V2 0 0 6 Inch Speed Dome Installation Manual V2 0 0 Appendix 1 Lightning amp Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000W like instantaneous lighting surging etc According to the actual situation outdoors necessary protection measures must be taken to secure the electrical safety 1 The distance between signal transmission line and High voltage eguipment or high voltage cable is at least 50m 2 Outdoor wiring should better be along the eaves as much as possible 3 In the open field wiring should be buried underground in sealed steel pipe and the steel pipe should be one point grounding Overhead routing method is forbidden 4 In strong thunderstorm area or high induction voltage areas such as high voltage transformer substation high power lightning protection apparatus and lightning conductor are necessary to be appended 5 The design for instal
27. rminals Figure 1 2 4 Back Box Circuit Board High Speed Dome 2 E OUT1 OUT2 GND IN7 IN6 IN5 IN4 1N3 1N2 IN1 AC1 SS AC2 1 Alarm In Out Terminals 2 inputs 2 outputs 2 Audio In Out Video Out and RS 485 COM Terminals 3 24VAC Voltage Input and GND Figure 1 2 5 Back Box Circuit Board Network High Speed Dome 6 Inch Speed Dome Installation Manual V2 0 0 5 Attach the back box of dome to the mount Set Screw Figure 1 2 6 Attach Back Box to Mount Note For outdoor applications please apply the thread compound and the damp proof stopper to threads of the back box and the mount After having made connections of the power cord video cable RS 485 control line and alarm input output lines if required close the hinged door and tighten the captive screw as shown in Figure 1 2 6 6 Install the dome drive As shown in Figure 1 2 7 align the tabs on both sides of the dome drive with the corresponding arrow labels on the back box to snap the drive into the back box firmly Figure 1 2 7 Install Dome Drive 7 Install the bubble and fasten the two set screws on both sides as shown in Figure 1 2 8 6 Inch Speed Dome Installation Manual V2 0 0 A TAS Figure 1 2 8 Install Bubble 1 2 2 Medium Speed Dome and Network High definition Dome Installation Note The following installation instructions are applicable to both medium speed dome and HD network speed dome models 1 Install the dome mounts P
28. should comply with the following mounting requirements The wall must be thick enough to install the expansion screws The wall must be capable of supporting up to 8 times the total load of the dome and its accessories 6 Inch Speed Dome Installation Manual V2 0 0 Y E gt A Step1 Drill mounting holes in the wall and install the expansion screws Drill four holes in the wall according to the mounting locations and then insert M6 expansion screws not supplied into the mounting holes Step2 Secure the wall mount to the wall Fasten the expansion screws through the wall mount and gasket by using four hex nuts with flat washers to secure the wall mount to the wall 6 Inch Speed Dome Installation Manual V2 0 0 Step3 Install dome to the mount Feed cables through the opening on top of the back box screw the back box into the threads in the mount and then use M3 screws to secure the dome Refer to Section 1 2 for installation instructions Note Follow the same instructions described above for the Short arm Wall Mount installation For outdoor applications please adopt the water proof measures The Short arm Wall Mount is not recommended for outdoor applications 6 Inch Speed Dome Installation Manual V2 0 0 Chapter 4 Corner Mounting Applications 4 1 Mounting Components o Wall Mount Applicable to the indoor outdoor pendant domes with the use of corner adapter wall adapter or pole adapter PE bw
29. use over heat or fire hazard 4 Please make sure that the plug is firmly connected on the power socket 5 When the product is installed on wall or ceiling the device shall be firmly fixed 6 If smoke odors or noise rise from the device turn off the power at once and unplug the power cable and then please contact the service center 7 If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the camera yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance Warnings 1 Do not drop the dome or subject it to physical shock and do not expose it to high electromagnetism radiation Avoid the eguipment installation on vibrations surface or places subject to shock ignorance can cause eguipment damage 2 Do not place the dome in extremely hot cold the operating temperature shall be 309C 65 C dusty or damp locations or fire or electrical shock will occur otherwise 3 The dome cover for indoor use shall be kept from rain and moisture 4 Exposing the eguipment to direct sun light low ventilation or heat source such as heater or radiator is forbidden ignorance can cause fire danger 5 Do not aim the camera at the sun or extra bright places A blooming or smear may occur otherwise which is not a malfunction however and affecting the endurance of CCD at the same time 6 Please use the provided glove when
Download Pdf Manuals
Related Search