USER MANUAL - Antiference
Contents
1. Antiference TA CONEXER DIGITAL MODULATOR 5 1 AV TO DVB T ENCODER MODULATOR USER MANUAL CONEXER DIGITAL MODULATOR 0 5001 CONTENTS 1 2 3 3 1 3 2 3 3 4 4 1 4 2 4 3 4 4 Safety considerations Description of the different elements Installation and menu structure Installation Powering up Menu structure Programming mode Description of the INPUT menu Description of the OUTPUT menu Description EXTRA menu Description menu MISC miscellaneous Programming using a PC Using HD LCN Technical specifications Factory settings Declaration of Conformity 2 Antiference 2 4 5 5 5 5 6 6 7 8 9 10 10 11 11 11 CONEXER 0 5001 DIGITAL MODULATOR 1 SAFETY CONSIDERATIONS 1 1 Connecting to the mains supply This product has to be connected to the mains supply If there is the slightest doubt concerning the type of connection available on the installation please contact your supplier of electricity Before carrying out maintenance operation or modification of the installation the modulator has to be disconnected Remark only use the supplied power adaptor 1 2 Over Voltage An overvoltage on the mains supply can cause short circuits and fire Never overload the power lines 1 3 Liquids2. This module should be protected from splashes Please assure yourself that no containers containing liquids are placed on this module Also be aware of other persons splashing liquids on the module 1 4 Cleaning Disconnect the module before cleaning Use only a damp cloth without solvents 1 5 Ventilation In order to assure an adequate air circulation and to prevent overheating the ventilation holes should not be obstructed The module may not be installed in a hermetically sealed environment Other electronic products or heat producing items may not be placed upon or near the module 1 6 Accessories The use of accessories not manufactured by the manufacturer can cause damage to the module 1 7 Installation of the module The module must be installed in a place well protected from direct sunlight All measures have to be taken to avoid installation in humid or sunny places Do not install near heating elements or other devices producing heat Assure yourself that the module is placed at least 10 cm from other equipment which is susceptible to electromagnetic radiation Do not install the module on unstable items a fall can cause physical or material damage IGITAL 9 MODUL ULA TOR a gt DC T Sy VIDEO er D 9909 4 0 2 Antiference 3 CONEXER 0 5001 DIGITAL MODULATOR 2 Description of the different elements C1 C2 C3 C5 C6 1
3. of the transport stream ID 2 Setting the Programme ID Service ID Use the buttons gt while keeping SELECT button pressed to change the number of the original network ID 3 Setting the Original Network ID Use the buttons lt and gt while keeping SELECT button pressed to change the number of the original network 4 Setting the Network ID Use the buttons gt while keeping SELECT button pressed to change the number of the network 10 5 Use the buttons gt while keeping SELECT button pressed to select a character Then release the SELECT button to set the following character Some characters have a special function namely Forward space lt Backspace Delete whole line B Antiference 8 CONEXER 0 5001 DIGITAL MODULATOR 1 Setting PMT PID Use the buttons gt while keeping SELECT button pressed to change the PID of the PMT Programme Map Table 2 Setting the Video PID Use the buttons gt while keeping SELECT button pressed to change the Video PID Setting Audio PID Use the buttons gt while keeping SELECT button pressed to change the Audio PID 4 leave this menu Press the SELECT button to leave this menu 4 4 The MISC miscellaneous menu 1 Setting Language of the menus Use the buttons gt while keeping SELECT button pressed to cha
4. 000 ks 9 Declaration of Conformity C LIMITED herewith declare that the modulator CONEXER DMSD01 complies with all essential requirements and any other applicable conditions set forth on directive 1999 05 CE According to the WEEE Waste Electrical and Electronic Equipment EU Directive do not dispose of this product as household waste or commercial waste Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country For information on recycling of this product please contact your local authorities your household waste disposal service or the shop where you purchased the product eV I Antiference 11 Date of issue January 2014 CONE DIGIT L D LATO 7 SINGLE AL Ova D TOR e TT T le input lt 64 s i USB AUDIO o VIDEO Au OUTPUT 6 El Antiference www antiference co uk
5. 4 and while keeping SELECT button pressed to change the FEC 1 2 2 3 3 4 5 6 or 7 8 6 Setting the Guard Interval Use the buttons gt while keeping SELECT button pressed to change the guard interval 1 32 1 16 1 8 or 1 4 T Setting the Output Level Use the buttons gt while keeping SELECT button pressed to change the value of the output attenuator 0 29dB 8 Setting the Audio Bit Rate Use the buttons 4 and while keeping SELECT button pressed to change the audio bit rate 128Kb s 192Kb s 256Kb s 320Kb s 384Kb s 7 Setting Video Bit Rate Use the buttons gt while keeping SELECT button pressed to change the video bit rate 100 20000 Kb s 7 CONEXER 0 5001 DIGITAL MODULATOR 10 Setting the LCN number Use the buttons gt while keeping SELECT button pressed to change the LCN number of the programme 11 Setting the Channel name Use the buttons gt while keeping SELECT button pressed to select a character Then release the SELECT button to set the following character some characters have a special function namely Forward space lt Backspace delete whole line 12 lt RETURM gt To leave this menu Press the SELECT button to leave this menu 4 3 The EXTRA menu 1 Setting Transport Stream ID Use the buttons while keeping SELECT button pressed to change the number
6. T2 T3 CONEXER DIGITAL MODULATOR DMSDOI SINGLE AV ENCODER DVB T MODULATOR Power supply input of the modulator 5 VDC 4 USB input for programming the DMSD01 by PC Video input Audio left input Audio right input RF input RF output LCD display 1 x 8 characters with backlight Select button Right button Left button B Antiference 4 CONEXER 0 5001 DIGITAL MODULATOR Installation and menu structure 3 1 Installation Install the DMSDO1 against wall using the wall fixing brackets to ensure cooling of the housing through natural convection see drawing Connect the audio and video source using CVBS RCA connectors Connect the RF input cable if present and the RF output cable If the input is not used please connect a 75 ohm terminating resistor to it Once the modulator is installed and the cables connected please proceed connecting the power supply to the modulator DIGITAL M 2 51 S N o M E lt AUDIO B VIDEO EFT a LEFT RIGHT OUTPUT i DO d E f 527 3 2 Powering Up Plug the connector of the power supply The LCD display will light up and shows the message Init followed a bar graph during starting up of the DMSD0O71 After starting up the message DMSDO01 and V1 9 firmware version are displayed alternat
7. ing 3 3 Menu structure The DMSD01 has different menus allowing easy access to the different parameters and to change them when necessary Below you will find the structure of the different menus sw me S wes rome zwwer em LIGHT MODE gt NET ID RETURN zowm eewrs zs je Lwmwwe zem eme ewe ATTEN lt VIDPID gt 2 lt Auprp gt _____ lt eRETRN _ NENNEN _ gt amp 8Antiference 5 CONEXER 0 5001 DIGITAL MODULATOR 4 Programming Mode To access the menus press and keep pressed the SELECT button Use the buttons 4 and gt to choose between menus INPUT OUTPUT EXTRA and MISC When you have reached the menu of your choice release the SELECT button Now you have access to the different parameters of the selected menu and inspect and change their values if necessary Use the buttons to go from one parameter to the other Once you have reached the wanted parameter press and keep pressed the SELECT button the value of the parameter is now displayed To modify this value use the buttons while keeping the SELECT button pressed Once the parameter changed you can release the SELECT button 4 1 The INPUT menu 1 Setting the input standard Use the buttons lt a
8. iscussed in Chapter 3 of this user manual can be modified by DMSDiFace 6 Using High Definition HD LCN In some systems you may want to broadcast a version of a programme in Standard Definition SD at the same time as High Definition HD With HD LCN numbering you can force HD Television sets to follow the HD LCN numbering and SD Television sets to follow the LCN numbering for those programs which are transmitted in duplicate For example You want to broadcast a BBC television programme in SD version as well as in HD Application of HD LCN would be BBC LCN 5 HDLCN 55 BBC1HD LCN 55 HDLCN 5 Television sets with the HD tuner will now put BBC1 HD on number 5 and BBC1 on channel 55 Television sets without the HD tuner will now put BBC1 HD on number 55 and BBC1 channel 5 B Antiference 10 CONEXER 0 5001 DIGITAL MODULATOR 7 Technical specifications Video bitrate 100 20 MBit s Layer Il Configuration Channel name SID LCN Network Name Network ID TSID ONID LCN PMT PID Video PID Audio PID DVBT Carriers Bandwidth MER 2K 8K 6 7 8 MHz gt 35 dB 47 862 MHz gt 80 dBuV adjustable 0 29 dB lt Supplied power adaptor 100 240V 0 5A 50 60Hz 5V 4A IT Dimensions 160 mm 110 mm 35 mm 8 Factory Settings CONTR CONST lt NETWRK gt NoName oo m ome oda lt gt 9 sw seres 6
9. nd gt while keeping SELECT button pressed to change this option in PAL or NTSC 2 Setting the picture format Use the buttons lt and gt while keeping SELECT button pressed to change the picture format between 4 3 16 9 or AUTO automatic Setting brightness Use the buttons gt while keeping SELECT button pressed to adjust the brightness 0 255 4 Setting the contrast Use the buttons while keeping SELECT button pressed to adjust the contrast 0 259 Setting Saturation Use the buttons gt while keeping SELECT button pressed to adjust the saturation 0 259 6 leave this menu Press the SELECT button pressed to leave this menu 2 Antiference 6 CONEXER 0 5001 DIGITAL MODULATOR 4 2 The OUTPUT menu 1 Setting the Output Frequency Use the buttons gt while keeping SELECT button pressed to change the output frequency 47 862 MHz 2 Setting the Bandwidth Use the buttons gt while keeping SELECT button pressed to change the bandwidth in 6 7 or 8MHz 9 Setting the Modulation Mode Use the buttons 4 and while keeping SELECT button pressed to change the modulation mode 2k or 8k 4 Setting the Constellation Use the buttons 4 and while keeping SELECT button pressed to change the constellation QPSK QAM16 orQAM64 D Setting the FEC Use the buttons
10. nge the language between French English Italian German and Polish 2 Return to Factory Settings Use the buttons gt while keeping SELECT button pressed to return to the factory settings of the DMSDO1 3 RETURN To leave this menu Press the SELECT button to leave this menu o 2 Antiference 9 CONEXER 0 5001 DIGITAL MODULATOR 5 Programming using a PC The settings of the DMSDO1 can also be changed using First please install the software DMSDiFace on your PC You can download this software from our internet site www antiference co uk conexer dvbt modulators and select the downloads tab After installation of this software connect the DMSDO1 using a USB cable not included to your personal computer Then launch the program DMSDiFace On the display of the DMSDO1 the message USB appears indicating that the programming is now performed through your PC The following window appears on your screen B DMSDiFACE 1 8 ANTIFERENCE 52 8 1 Standard Pict Format NE Light P Contrast 2 Saturation EU Freq kHz TSId 474000 100 Mode Const Bandwidth F E C Guard Int Level Att OdB Network Vers Original Id Id 28 9018 12293 14 1 Antiference 8 PID Video PID Audio PID 32 48 6000 Kb s 49 384 Kb s v Now all parameters d
Download Pdf Manuals
Related Search