Home

User Manual

1. Reminder If the ActiveX control is not downloaded successfully please check if your browser s safety level or firewall setting is too advanced To change these setting run Internet Explorer and go to Tools lInternet options Internet Custom level enable For details please refer to the Picture 6 1 46 IQCCTV 1Q1920DVR User Manual Security Settings Settings Disable Enable e Prompt Download unsigned Activex controls Disable Run Actives controls and plug ins Administrator approved meu Reset custom settings Picture 6 1 lf running the web application for the first time the download will take roughly one minute to finish and install the ActiveX controls 47 IQCCTV 1Q1920DVR User Manual 6 2 Web Application Manager Log in After ActiveX controls are installed please input user name password and client port Then select lt Main stream gt or lt sub stream gt and tick select lt Open All Channels Preview gt I CCTV Login HD 960H User Name admin Password Client Port gnno Bitrate Sub stream v Language English M Remember Pwd Open All Channels Preview Login Reset Now click the Log in button to access the DVR remotely and monitor live video images using Web browser Please note that defaulted password is empty The System allows the Administrator to set new passwords as per instructions in section 6 3 3 System set gt
2. gt Latch time Set how long the buzzer will sound when external sensor alarm is detected 10s 20s 40s 60s gt Show Message Change the message that shows on the screen when sensor alarm is detected gt Buzzer time Set how long the buzzer will sound when the sensor alarm is detected Off 10s 20s 40s 60s gt Send Email Choose whether to send images to a specified email when the alarm is triggered gt Full screen Alarm The function is defaulted to On When motion is detected the corresponding channel will be switched to the full screen mode gt Record Channel The record channel will be activated when a moving object is detected gt Post Recording Set how long the alarm record will last after the alarm ends 30s 1minutes 2minutes 5minutes gt Copy Copy current channel parameters to any other channel or all channels 40 IQCCTV Alarm Type Video Loss Motion Detection I O Status 1Q1920DVR User Manual Function Sends an alarm when the DVR can t receive video signal such as camera damage broken cables or damaged to the power supply When an object moves into motion detection area the alarm will be triggered You can adjust sensitivity level to suit the needs of your actual application environment oystem can convert an alarm signal triggered by external sensor into a signal identified by the system When a Hard Drive is not detected HDD damage power supply malfunction or
3. Format HDD Format USB Default Apply Exit When the DVR is connected to a HDD the system will automatically detect if the HDD is normal or not If the cable connected to the HDD is loose or the HDD is abnormal the HDD status will be shown as No Disk If the HDD needs to be formatted the status will be shown as no format However if the HDD is fine the status will be shown as Normal NO Indicates the HDD has been preset by the system Status Only available when HDD has been formatted Total Space Total size of the hard drive currently installed Free Space Total amount of free space available on the hard drive currently installed Useable Rec Time Free space currently available in hours Auto overwrite When set to ENABLE the DVR will record over the oldest files on the hard drive The DVR will always be able to record events as they happen however it does mean that the user will need to take important events off the HDD before they are overwritten If the overwrite function is set to DISABLE the DVR will stop record once the DVR is full Whilst you wont lose old footage you run the risk of missing new events as they happen HDD Format Formatting the HDD will erase all data i e footage which is stored on it and re create the FAT file allocation table gt USB Format If you have a USB flash drive connected to the DVR you can format that too To do this click the USB Format button and click
4. IM 4 bd All Inverse Search Exit 25 IQCCTV 1Q1920DVR User Manual 5 3 3 5 File Backup 5 3 3 5 1 Back up File Based on Event In the File List mode to backup records check the boxes which correspond to the records and click Backup button to enter into the below windows Select USB as backup device and click the Apply button and then enter into the window as shown below Warning 5 files are selected No 4 file is in process Backup is in progressing do NOT remove USB After the backup is finished please click OK button to exit the backup menu Please note e File will be saved as 264 format e Playback the record files via the IQ CMS player When installing the IQ CMS the system will automatically install the player e The DVD file will be saved as nvr format e Please make sure the back up device U Flash disk USB port or DVD Recorder is connected properly before the backup 26 IQCCTV 1Q1920DVR User Manual 5 3 3 5 2 Back up File Based on Time This functions allows the user to back up recorded files based on time Please follow below steps to back up these files He OER LB oN Input the start time and end time on the time edit box Click Search button Check all the files you desire to backup Click the Backup on the bottom 5 3 3 5 3 Play Backup File Copy one backup file to your PC Open Playback player and click icon or the button to find select the
5. Remote Setting Local Setting Logout Ld Displa y Network Refresh Save E Record T Network HTTP Port poo EE nei E SIRE IF Address DII EE 168 1 122 SubSream Sibnet Mask Email DDNS poo O O Picture 6 18 55 IQCCTV 1Q1920DVR User Manual Remote Setting ogol ve Playback Remote Setting Local Setting Network Network Refresh Save Mobile Por IF Address 92 168 168 1 1 v Pict 6 19 n Picture 6 20 Sub stream shown below Relative parameters should be consistent with the DVR local settings Audio Email setting Click the Email setting option to set alarm email configuration parameters shown below Please note that the detailed parameters should be consistent with DVR local setting Remote Setting Refresh Email Ea Schedule 56 IQCCTV 1Q1920DVR User Manual DDNS Setting Once the DDNS has been applied service the user can enable the lt DDNS gt function under any one network type mode Static DHCP and PPPoE Once this has been done the user can remotely visit the DVR through domain name http domain name port No Please note that the details in this setting should be consistent with DVR local setting 57 IQCCTV 1Q1920DVR User Manual 6 3 3 4 System Click the lt System gt to unfold its sub options HDD PTZ General and Users HDD Allows the user to check the HDD status and overwritten time Please note that the details in this setting sh
6. Advanced option to unfold its sub options Motion I O Alarm System update Load default Events and system maintain Local Setting Logout Display Motion Copy Refresh Save Record Enable Network Y TENE r r r ar I TA We J 8 60 iili System j Full Screen Enable Record Past Recording Record Channel Motion Maintain CHO1 W CHO2 W CHO3 Fei Events gelu W CH06 Neira Nell Firmware Update show Message send Email Clear 60 IQCCTV 1Q1920DVR User Manual Motion Detection This menu allows the user to configure the lt Sensitivity gt lt Alarm out gt lt Alarm record gt and lt Alarm Capture gt of the DVR Please note that the details in this setting should be consistent with DVR local setting Motion Retresh I O Alarm 8 16 32 Configure lt I O Status Alarm output gt I O Alarm record and Alarm email Please note that the details in this setting should be consistent with DVR local setting Display Alarm Alarm In Ks Record Network ce Kosia Reach Kosin 61 IQCCTV 1Q1920DVR User Manual System update This section allows the user to upgrade DVR system remotely Remote Setting Please follow below steps to upgrade the system A Select the upgrade file s path as shown below Please note that the format of upgrade file is SW Choose file PR Look in co dvrupgrade Q 3 em v 165229130623 sw uu BETIUSUETHNIETEUETTE ETE ETESEN My Re
7. Select DHCP and click Apply button Exit and restart DVR Input media port and HTTP port oet the IP address captured by the DVR and HTTP port to a router View the DVR remotely Input the IP address of your domain name server Please note All the parameters that are set are available only when you click Apply after system has restarted The user needs to change MAC address when there are multiple DVRs at the same local area network For details please refer to section When selecting Static from the Type the user can directly input the IP address Subnet Mask Gateway and DNS as shown below To set your net type to Static a ae T oet Client port number such as 19009 and the port that you want to forward to Input the HTTP port number such as 19010 and the port that you want to forward to Input a specified IP address in the IP address column The Subnet Mask gateway and DNS server should be consistent with your router s configurations Input the DNS address Please check router before doing this The setting should be consistent with the router s Click the Apply button p puse E a jum Network Sub Stream Emal DDNS Type PPPOE Mobile Port 18004 Ie Client Port HTTP Port User Name Password DNS 1 192 168 001 001 ww DNS 2 f I Auto Port Forwarding Enable w Default Apply 30 IQCCTV 1Q1920DVR User Manual When selecting the PPPoE option from the Type drop down list The user can input the us
8. backup file and then click the open button Highlight the file you have selected and click Play button Play button click the icon to playback the backup record Pause button click the icon to pause the backup record Stop button click the icon to stop the backup record Next Click the icon to play next record Prev Click the icon to play previous record FF button click the icon to fast forward the backup record at x2 x4 x8 and or x16 speed Open click the icon to open one record file Click the icon to place the playing record to top Snapshot button click the icon to capture the live image and save the captured one to directory video clienticapture LL Volume Adjust click the icon to adjust the volume ES Add fold or file to player Delete one file in the list ES Delete all the files in the list E Unfold or fold the list files g Advance Configuration click the icon to set 2f IQCCTV 1Q1920DVR User Manual 5 3 3 4 Log Search Go to the Main menu gt Search gt Log option to enter into the Log search interface as shown below t r Record Search Event Search Backup Log Log Type All Search Start Time 2013 07 11 End Time 2013 07 11 Ey CON TIME POINT RECORD This menu allows the user to preview the log information searched Click the Backup button to export all the log information 28 IQCCTV 1Q1920DVR User Manual 5 3 4 Network 5 3 4 1 Network s
9. CH1 w Speed 4 31 Preset Speed fum 3 l TOTAL 1 ZOOM ZOOM No 002 FOCUS Time 003 IRIS 4M ode FOCUS 1c Sh To enter into the PTZ Control menu click the O icon Here the user can control the camera with Pan Tilt and Zoom capabilities Click Zoom button to zoom in out the image click Focus button to focus the image click Iris button adjust iris to open or close 43 IQCCTV 1Q1920DVR User Manual To set a pre set point please see the following steps 1 Total Set up pre set point quantity 2 Cur Point Indicates the starting point cruised System default point is 01 The model supports up to 255 pre set points 3 Stop time Sets the stop time at each point Range is 1 255 4 GOTO Go to a specific preset point 5 Set Establish a set of specific preset points of a PTZ camera Select the camera you desire to set a preset point Adjust the camera to the desired direction Click Set to set the point as preset point Click Save to save the preset point e Follow the above step to add one more preset point 6 Save Save all the preset points 7 Clean Delete one selected preset point apoy Please Note Up to 254 pre sets per one camera can be stored However actual preset quantity differs depending on PTZ performance 5 7 PIP Mode The user can display a Picture in Picture PIP in live mode PIP has two display modes including 1X1 display mode and 1X2 display m
10. HDD auto overwrite is off and there is not enough free space an alarm will be triggered 5 3 6 3 Maintain Click Main menu gt Advanced Maintain to enter into the Maintain menu as shown below VN ON Motion Alarm Maintain Events StartupWizard Enable w Auto Reboot Enable w Reboot Every Week Y Sun 00 00 Update Load Default Reboot Shut Down Load Settings Save Settings Default Apply Auto Reboot Enable the auto maintain function so that the unit will perform maintenance regularly as per the user s needs System Upgrade To perform upgrade function after decompressing the update file package copy the file named dvrupgrade to root directory of U flash disk Then Insert the U flash disk into USB the port of the DVR and Click Upgrade Load Default If Load Default is selected initialize the system to the factory default Reboot Click the Reboot button to manually restart the DVR system Shutdown Click the Shutdown button to shutdown the device 41 IQCCTV 1Q1920DVR User Manual Load Setting Load the parameters in the U flash disk to device After loading successfully the system will auto restart gt Save Setting Save the parameters of device to a flash disk Note x x ud m Do not take out the USB memory or break the power during the update When the update is done the system will be automatically restarted Please manually recovery ex factory default after system rebooting
11. Record parameter Schedule and Main stream Playback Remote Setting Local Setting Picture 6 16 Picture 6 17 Record Parameters Under the Record parameters option the user can set the channel enable record pack time and Pre record status Schedule For details on how to set parameters please refer to DVR local setting Shown as Picture 6 16 The Green light stands for Normal record yellow stands for Motion detection and Red stands for I O triggered record o4 IQCCTV 1Q1920DVR User Manual Logout Rec Parameters Y Schedule ee c C System P po Advanced Main Stream For detailed settings please refer to DVR local setting shown as Picture 6 16 This option allows the user to modify the resolution frame rate Bit rate and audio of the record channel 6 3 3 3 Network Parameters Unfold the Network option to enter into the sub options Network sub stream Email mobile and DDNS configuration The IQR960D range supports three network types including Static DHCP and PPPoE The oystem default sets Static as its network type The user can allocate IP addresses and perform Port forwarding If the user sets the UPNP to On there is no need to perform port forwarding When the network parameters have been modified successfully the DVR will automatically restart For details on how to set parameters please refer to below Picture 6 18 Picture 6 19 and Picture 6 20
12. User Configuration menu 6 3 Live Interface After successful logging in to the web manager you will enter into the Live interface as shown below e we ue ue a2 ue ue ue 55666565 5 5 6 okom a R E ORR 48 IQCCTV 1Q1920DVR User Manual 6 3 1 Menu Bar Menu bar includes Live Replay Configuration Path Configuration and Logout options 6 3 1 1 Live Display After running the Web Application Manager on your local PC the system will be defaulted to enter into lt Live gt interface Click the Play button to Open close live images and enter into on spot record and Capture quad 9 split or 16 split mode by operating the control bar on the bottom of screen Volume switch r1 Record icon recordings will be saved to a specified position after starting record Snapshot function Capture the live images and save it to a specified position The image should be saved as bmp format gt Clicking the icon will close open the current channels live mode Or click the right key of mouse on each lt Live gt window to pop up the interface To show bit rate Right click the Preview window and tick select the option to show current bit rate B Open all the lt live gt channels Close all the lt live gt channels 249 Display previous group of channels Display next group of channels 5l Click the icon to enlarge current window to full screen right click to pop up menu options whi
13. When the clip has finished a pop up dialog will appear allowing you to select if you want to save the clipped video file gt Zoom Function When one channel is playing back the oy icon will appear in the Play control bar Click the icon to zoom in one area of the playback screen shown as Picture 5 15 5 3 3 4 Event Search Click the Main Menu Search Event Search to enter into the interface as shown below The user can highlight and double click the desired record for playback This feature also allows the user to filter the records to view based on date time and channel and record mode search El First Page Go to the first page on the list When you view other pages click the First button to go back to Page one Ei Previous page Go to the previous ones of current page Clicking Pre button will take you back the previous page B Next page Go to the next page Clicking the Next button will take you to the next saved events of current page except the last page Ul Last page Go to the last page Clicking the last button will make take you into last page quickly ALL Select all Allows you to select all the events on the current page Inverse Select Invert Allows you to select other events on the current page except those you have currently selected t Record Search Event Search Backup Log Search Date 2013 07 11 CH All Y Search Time 00 00 18 29 TYPE Al v ol a Ed zd DAY START END SIZE BAK
14. and install ActiveX Plug in automatically If your computer system is Vista you may need to setup the user authority For details please refer to the image below Start 5esetup control panel Tick y use UAC to help protect your computer and confirm OK Vista System Turn on User Account Control UAC to make your computer more secure User Account Control UAC can help prevent unsuthorized changes to your computer We recommend thet you teewe UAC tumed on to help protect your computer E Use User Account Control LIAC to help protect your computer gt ew Commu Win 7 system UE Tm E ney N ONE User Account Control Settings i eS i i p File Edit View Tools Help mputer e Control Panel Home a Make changes to your user account Manage your credentials ie Create a password for your account i Create a password reset disk Ch T Never notify me when ange your picture l Link online IDs z in M fil ti Change your account name Pro ams E install software or make changes to anage you n Ree EE ERI sey Qj Change your account type a S Configure advanced user i ne poe eee PORE properas Manage another accoun Change my environment _ e variables i Not recommended Choose this only if you need to use programs that are not certified for Windows 7 because they do not support User Account Control Nev tify ies y Parental Controls
15. bottom of the sub menu windows to accept the changes and click the OK button when prompted to save 2 If you want to cancel the modification click Exit button to exit the menu 3 When clicking DEFAULT button all the system default values will be reset to default value 5 3 1 2 Output mode To enter the output mode menu go to Main menu Display Output to enter into the output set interface shown as shown below VV ON Live Output Privacy Zone Video Output LIVE OUT Y View Setup Disable SEQ Time VGA HDMI Resolution Init DEV Transparency ome Volume Default Apply Video output Supports CVBS output Live and Spot mode simultaneously Live mode is the main output and Spot is the auxiliary output CH Sequence This option is defaulted to Off and the sequence time is 5 seconds The user can activate the option as desired Rotate time Allows the user to set the sequence time Minimum time can be set to 3 seconds VGA HDMI Resolution Select VGA or HDMI output including 800x600 1024x768 1280x1024 1440x900 and 1920 x 1080 Display Mode Live output display window will include Single Quad 9 split and 16 split mode Spot output Display window will include Single Quad and 9 split mode Transparency Adjust the menu s transparency Range is 1 128 Margin Adjust the whole screen s margin Details operations please refer to the Picture 5 4 Volume Adjust the DVR volume 19 IQCCTV 1Q1920DV
16. ges cscsdattgoscacadatucwaecostuautaescacadeas Del EIVeMOGOO cs ete tel e Fu dva ERG malin 9 9 1 2 OUMU MOG epus uc Ead o betur 0 3 1 3 Privacy Zone 0 cece cece cece cence eee e eens D102 FRCCOI SCL sciseenssiccseaamasadiaapaseases Hoo oT E pr 5 3 2 1 Record Parameters 9 9 2 2 S CIedule ussicetek o ub pn Na EPA ERCRKwEORC SERM 5 3 2 3 Main Stream ceeeeeeeeeee Di 0 02 DCA Cas sd Gase dgai uio paa E vaa pi nita E EE EN VR Tas 5 3 3 1 Record Search 5 3 3 2 Charinel Select ise r n es 5 3 3 3 Time Axis setup file clip zoom in out 5 3 3 4 Event Search seeeeesl D 9 9 9 Fe BACKUP secsikutimievebu eise c Utd canes 50 3 3 5 1 Back up File Based on Event 0 3 3 5 2 Back up File Based on Time 0 3 3 5 3 Play Back up File 9 9 9 4 LOg SCAICM essendi o sp iieii 16 16 18 18 18 19 20 21 21 21 22 23 23 23 24 25 26 26 2f 2f 28 5 3 4 Network 5 9 44 1 NetWork OGL sotese siae ato opp S Db eS SEES 5 3 4 2 Mobile Set euo co dinh Dor ul DOES 0 3 4 3 Router s Port Forwarding 5 3 4 4 SUD Ol edili scc otis rnt rU aiai 9 945 EMail DCL soot re PUeo A RT dE E 5 9 4 5 DDNS SOLUS Eisen La A 5 3 5 System 5 3 5 1 ADD SD esosexcou ee apu ee ee ERE OL R e Ee SEG INN PIZ MTTCTE 5 23 59 9 GE
17. port number for most mail servers is 25 However Gmail server may have a Port number 465 SMTP server Indicates the server address used Sender address Indicates the sender s email address The email address should be consistent with the serve For example if you use email address aaa gmail com the server should be smtp gmail com Receiver address Indicates the receivers email address The email address used to receive images transmitted from the DVR alarm Please clear the images you have received as soon as possible to avoid overloading your email account 5 3 4 6 DDNS Set Server Select the DDNS provider Host name Input the host domain name you have registered at dynamic domain name system such as DVR2009 3322 org User Name Input a user name registered before applying for a domain name Password Input a password you set when registering a user name Click the apply button and restart the DVR Once the DVR has restarted enter the domain name for example http iqr960d4 3322 0rg 8080 to view the DVR remotely Network Sub Stream Emall DDNS DONS Disable E Servet NIGHTOWLDVR v Host Name User Name Password 34 IQCCTV 1Q1920DVR User Manual 5 3 5 System 5 3 5 1 HDD Set Click the Main menu gt Device gt HDD to enter into the interface shown as shown in the picture below r HDD PTZ General Users Info No State Free Total Free Time Select NoHDD 0 0 No HDD 0 0 Overwrite Auto
18. to Alarm once one alarm has occurred the record will be saved as Alarm record Under the Scheduled mode no record interval allows the user to activate manual record and the recorded file can be saved as a Normal record 14 IQCCTV 1Q1920DVR User Manual Appendix 3 Troubleshooting 1 Q What can do if the system does not detect the HDD A Check if the power supply system is properly connected and data cord and power cables are securely connected 2 Q We have changed the password but do not remember the new password how can we access the system A If you forget the system password please contact your supplier 3 Q We are not getting any video signal on the DVR what is wrong A Check camera video cable and connections Check monitor video cable and connections Confirm that the camera has the power and or check camera lens setting 4 Q Why do some channels display just a blank screen even if they receive video sources A Check if the camera is connected to the system properly displays the image Check if the camera is properly supplied with power 5 Q Can the DVR have problems if it gets too hot how can prevent this A The DVR has a fan to help it dissipate heat while it is running Please place the DVR in a place where there is good air circulation and away from heat sources to increase stability and life of the DVR 6 Q The Remote Controller doesn t work normally A Check if the battery is power off or chec
19. 2 32 33 33 34 35 35 36 36 37 38 39 39 40 41 42 43 43 43 44 44 44 45 45 45 45 46 46 48 48 49 49 50 50 51 51 52 53 53 54 55 58 60 63 O Forero d ar 6 4 Mobile Viewing Access Instructions Appendices Appendix 1 Operation Function Table Appendix 2 Alarm Record Setting su Appendix 3 Troubleshooting seeueeeeeeeee Appendix 4 Usage Maintenance sses Appendix 5 Accessories 64 64 72 72 74 19 76 Tf Safety Instructions Please read the instruction manual carefully before using the equipment Please make sure to use the PSU supplied with the DVR All equipment should be placed in an area away from water and moisture Do not install the DVR near any heat source such as radiators that produce heat Please don t use the equipment near a dusty area or near an intense magnetic field Before cleaning the equipment unplug the unit from the wall Please refrain from using liquid aerosol cleaners and use a damp soft cloth Please make sure to unplug the DVR during a lightning storm Do not place the equipment on an unstable surface Please do not block any ventilation openings on the DVR IQCCTV 1Q1920DVR User Manual Chapter 1 DVR Features ee Double video output Monitor VGA virtual ou
20. 20DVR User Manual 5 3 6 Advanced 5 3 6 1 Motion Click the Main menu Alarm Motion to enter into the interface as shown below r li I j Motion Alarm Maintain Events CH CH1 Y Enable Area Setup Sensitivity Alarm Out Latch Time 105S Y a Show Message Buzzer OF kd 24 Send Email Y Full Screen Record Channel Post Recording 30S w MAILE 04 05 06 07 08 09 1 0 1 JEFE IEE Copy CH1 w To AI v Copy e Default Apply Channel Enable disable the motion function for any channel Area Click the Setup button to enter into area setup interface Sensitivity Set sensitivity level of motion detection from high to low Sensitivity ranges from 1 8 with 8 being the most sensitive Alarm out Connect external alarm sensor gt Latch time Set how long the buzzer will sound when a moving object is detected 10s 30s 40s 60s Show Message Change the message that displays on the screen when the motion alarm is detected gt Buzzer time Set how long the buzzer will sound when motion is detected off 10s 30s 40s 60s gt Send Email Choose whether to send images to a specified email when the alarm is triggered gt Full screen Alarm The function is defaulted to On When motion is detected the corresponding channel will be switched to the full screen mode gt Record Channel The record channel will be activated when a moving object is detected gt Post Recording Set how long the alarm
21. 3 58 19 Not download oO O 10 2013 08 17 04 21 32 2013 08 17 04 34 40 Not download m 12 2013 08 17 04 38 15 2013 08 17 04 49 34 Not download 13 2013 08 17 04 49 34 2013 08 17 05 02 50 Wot download 14 2013 08 17 05 02 48 2013 08 17 05 05 56 Not download M1 16 2013 08 17 05 06 26 2013 08 17 05 07 12 Not download v lt ll gt Start download Stop download Tick select the recorded file you want to download and click Start download The System will download the recorded file in turn and save to the local PC 6 3 3 Configuration 6 3 3 1 Display Configuration Click the Display option to find the sub options Live and Privacy zone Live This option allows the user to modify channel name Position Show time and Record time If the show time is set to disable the current system time will not appear on the screen in Live mode Similarly if the record time is set to off the system time can t be found in the record file 53 IQCCTV 1Q1920DVR User Manual Privacy zone Each channel can set up to four privacy zones as shown below For details on how to set parameters please refer to section 5 3 1 3 To delete one privacy zone please firstly select one zone and click the Clear button then click Save on the right corner Remote Setting Local Setting Privacy Zone Copy Refresh Save 08 20 2013 08 02 22 6 3 3 2 Record Click the Record option to unfold its sub options
22. Full HD DVR with HDMI Output Real Time 1080P Recording and Mobile Internet Access HDMI Remote Touch Resolution Output Access Panel User Manual Models lIQR1920D4 IQR1920D8 Version 1 Contents Safety IS Ul UG COINS ete sso TEE EE EET Chapter 1 DVR Features ook s veu ERE Rx VA MEER ERE FREI PERI US RENE UM ETHIC T MUN UTE Chapter 2 OVerVIOW xoa pr EE ER PIENE ruE VE PUE SEE IUE 2 I FFOBUESDelS secet ssec pt mte REPE PAIS PM M IROPRPRPRR DEP RM 2 1 1 4 8 Channel DVR Front Panel 22 eal AINE S ussasteneidstuedpusc ERN RE LI CIS EEUU eet 2 2 1 4 8 Channel DVR Rear Panel Chapter 3 DVR Connection Chapter 4 DVR Boot Up 4 1 System Initialization 0c cece cece eee cece ee eeeeeee eens 24 2 LING IMC ACE seta ci several atta dee a S RO DR Ra ap eo dd 2 2 2 RS485 Sensor Alarm Port Functions 2 3 4 8 Channel Remote Controller 2 4 MOUSE OPerallONn x ve ERE EE Or E RO ads 3 1 HDD Installation enn Ry 3 2 Camera and Monitor Connection 12 12 12 13 13 14 16 Chapter 5 DVR Men scirrata Ps a REMINDS Ds MEET Cx VM tas Ou IPPODAJD MENU oiexivt arie Quy et ON 5 2 Main Menu Guide eee mI mre 5 9 Wid IN Me NU scccc lt cxcktessdet cay tatesadeveauehtessdedaausoteandatcenesees OF Oe EB M c
23. I and Internal 63 IQCCTV 1Q1920DVR User Manual Record Path D ADVR Record u Download Path DADYR DownLoad mmm Snapshot Path DADVRiCapture LL File type Interval Min Save 6 3 5 Logout Click the fo Icon to return back the log in interface 6 4 Mobile Viewing Access Instructions The DVR is currently compatible with mobile phones running iPhone and Android operating systems Below are these Mobile Viewer s installation procedures iPhone 1 Connect your phone to the internet using 3G or WIFI 2 Download and install the free IQCMS app from the App Store 3 After finishing installation the IQCMS icon will be displayed to mobile phone interface shown as Picture 1 4 Tab the IQCMS icon to open the app Live Monitor Remote Playback Hom Record Playback Image View Device Manager as v o Loading Help Picture 1 64 IQCCTV 1Q1920DVR User Manual Add and delete device The device manager will allow the user to add or delete a device and also modify device properties Tab Device Manager on Main Menu to open this interface as below 2 47 4 Carrier 10 13 AM DVR Info Live Monitor Name DVR1 Address 192 168 1 11 Port 9000 UserName admin Password e eeeee Click to retrieve channels count Channels 8 To add a new device click the Add button at the top right then you can input the device name address ip or domain name port user name and pa
24. It will be available only when DVR return back to Preview mode and no any operation 5 3 6 4 Event Click Main menu Advanced Event to enter into the Event interface as shown below po j I j Motlon Alarm Maintain Events Event Type Disk Full w Enable Y AlarmOut Latch Time 10S ww 4 S 1O Me SS ige SY Bi izzet 0S Ba Send Email v Default Apply Event Type Three abnormal types Disk No Space Disk Error and Video Loss Enable Activate abnormal alarm Alarm out Select Enable or Disable Latchtime Set how long the buzzer will sound when external sensor alarm is detected 10s 20 40s 60s Show Message Change the message that shows on the screen when sensor alarm is detected 42 IQCCTV 1Q1920DVR User Manual 5 4 Menu Lock To access the system safety feature click the L icon to lock the system interface when leaving the DVR To login to the DVR again input the device code and password to unlock the interface as shown below Please Note Administrator has full authority over Main Menu operations and has the authority to limit common user s operation 5 5 Split mode The DVR displays 4 8 live images in the sequence of single 4 split and 9 split modes When entering into the 4 split mode the live images will be displayed in turn CH1 4 CH5 8 and CH13 16 When entering into 9 split mode the live images will be displayed in turn CH1 9 CH10 16 5 6 PTZ Control Oneac
25. Nel al star aie acetate D UNA E LEE a LEE 0 9 9 XS gt ee ee AA 5 35 5 IDnFOF Ha HOT a sovchtcn ks roro deans REPOS ES beens 5 3 6 Advanced 9 965 TI MOVON eiii deno Uno p cette aai 5 23 52 Alam OL coste qetatest m oet Eod ax 9 9 0 9 MaMa issue su ic eR ri RRAPR PORE PST iP RgPUeIs 9 910 4 E VOLLE ssecuscsetiocseta mede T Eu MORIS SPP IDGE 5 4 Menu Lock 5 5 Split Mode 5 6 PTZ Control 5 7 PIP Mode 5 8 Record Search 5 9 Mute eei ETenS 5 10 Manual Record 5 11 Stop Record 5 12 Start Sequence 5 13 Start Cruise Chapter 6 Web Application 6 1 ActiveX Control Download and Installation 6 2 Web Application Manager Log in 6 3 Live Interface 6 3 1 Menu Bar 0 94 T Eve DISDIAV istante aa eee ARE dex e D6 5 1 2 PIZ ConttolJ dt ERE P EXPE INCRddE 6 3 1 3 Video Control itr REED YR REP des 6 3 2 Playback 6 3 2 1 Record Search eese 0 9 2 2 PlayOaCk CONTON 32e eta decuu xum aoo dete 6 3 3 Configuration 6 3 3 1 Display Configuration D 9 2 I COO tte ee CRM EDU eet 6 3 3 3 Network Parameters 0 9 9 4 OVSIGITI susce cure taste isse te pero od texas debui 5 9 9 0 7X0 ValiC B c kcassetamee uia tees donee data duque 6 3 4 Local Setting 29 29 3
26. OK VN NN N ON Note When configuring your DVR please make sure that the hard drive HDD options are correctly set It is strongly suggested that the user formats the HDD before recording for the first time 35 IQCCTV 1Q1920DVR User Manual 9 3 9 2 PTZ Set Click the Main Menu gt Device gt P TZ to enter into the below window shown below li l l HDD PTZ General Users Info Channel CH1 v Protocol Baudrate DataBlit StopBit Parity Crulse Address 001 Copy CH1 Iw To Al lw Copy Default Apply Firstly select the channel you desire to control and set PTZ protocol Pelco D or Pelco P Then select the Baud Rate 1200 2400 4800 9600 Data bit 8 7 6 5 Stop bit 1 2 Parity Check None Odd Even Mark Space Address Code and Cruise status respectively Please note The PTZ device can only be activated when a channel in connection with the PTZ camera is selected 5 3 5 3 General Click the Main Menu System General to enter into the interface shown in the image below j I I j i HDD PTZ General Users Info Date 07 11 2013 Time Date Format MM DD YY E rime Format 1 2Houl LI DST Setup NTP Setup Landuade ENGLISH v Video Format NTSC v Menu Timeouts Min wv Default Apply The user can modify the system date time date time format time zone language video format and menu time out 36 IQCCTV 1Q1920DVR User Manual Click the DST Setup button to enter into the below in
27. R User Manual Left Margin Right Margin Top Margin Bottom Margin moror leer ee i Picture 5 4 Click the Live button to pop up the interface as shown in Picture 5 5 This allows the user to perform a channel sequence setting Similarly Click the Spot output option and set relative parameters Picture 5 5 5 3 1 3 Privacy Zone This function allows the user to setup privacy zone parameters as show in the image below Each channel can have up to four privacy zones Follow below steps to set Select the area no Area 1 Area 4 Click Setup to adjust position of mask area After finishing position adjust click right key of mouse to return back Privacy zone interface Click Apply to save the above setting PII Live Output Privacy Zone Channel Privacy Zone Area Setup Default Apply 20 IQCCTV 1Q1920DVR User Manual 5 3 2 Record set 5 3 2 1 Record parameters Click Main menu gt Record gt Record Para to enter into the interface shown in the image 5 7 below Channel Setup the channel desired gt Record Set up the record status Enable Disable of each channel gt Pack Duration Indicates the maximum continuous record time 15 30 45 and 60 min opy CH1 w To All Picture 5 7 5 3 2 2 Schedule Click the Main Menu Record Schedule to enter into the interface as shown below The Channel option allows the user to select any desired channel To setup weekly sc
28. Synchronise playback option Once the channels have been selected click the Bi icon to start the playback When the mouse curser is moving on the time axis the current time will appear in the screen Click the Eu Ex icon to zoom in out the time bar display ratio 51 IQCCTV 1Q1920DVR User Manual 6 3 2 2 Playback control 6 10 Playback Control Bar EE EN Open close audio Stop Playback control bar x1 2 1 4 1 8 normal x2 x4 x8 Download Fullseeen screen B wu all the channels ga om O between original proportions and Screen Resolution Record file clip After opening playback click the EI icon to clip the selected file Then click again to stop the clip function Record clip files will be saved in 264 format Snapshot function Move the mouse curse to the channel you want to capture and click the rn icon to capture the live images remotely After capturing the images successfully they can be saved to a specified path shown in the image below The captured file will be saved as bmp format 52 IQCCTV 1Q1920DVR User Manual Record file download Click the J icon to enter into the below interface Download file Playback window 01 E 2 2013 08 17 00 59 57 2013 08 17 02 00 02 Not download Ms F 4 2013 08 17 03 00 00 2013 06 17 03 36 55 Not download 1 6 2013 08 17 03 37 40 2013 08 17 03 55 32 Not download oO 1 38 2013 08 17 03 57 46 2013 08 17 0
29. anual Chapter 4 DVR Boot Up 4 1 System Initialization After powering the DVR and pressing the Power button on the front panel you will enter into the system initializing screen shown as below JIOCCTV HD S608 After initialization the setup wizard will begin 1 HDD Management As shown in below the user can set the HDD management record schedule and network configuration In this option the user can also select the overwrite types and format the HDD HDD MANAGEMENT 2 Record Schedule Set the record schedule with the options shown below RECORD SCHEDULE H E _ N Norrnal lf M Motion A Alarm _ No Record Copy Sun To All Copy CH1 To All 13 IQCCTV 1Q1920DVR User Manual 3 System Configuration In this section the user can set the time date DST and NTP as shown below SYSTEM GENERAL CONFIGURATION Date 2013 07 11 Time 18 25 06 Date Format YY MM DD Time Format 24Houl Setup Setup ENGLISH PAL 4 Network Configuration Set the network configuration as shown below NETWORK CONFIGURATION Static wv Mobile Port 1 8004 HTTP Port IP Address 4 2 Live Interface After finishing setup wizard the system will enter into Live screen The image below shows the 16 split display defaulted by system In Live mode double click the mouse over the live image of any channel and the image will be maximized to full screen By double clicking again the image will
30. be come back to the 16 split display mode Clicking the right button of the mouse to enter into the Pop up Menu Once in the Pop up menu click the left button of the mouse to select menu items To exit this menu click anywhere outside the menu area 14 IQCCTV 1Q1920DVR User Manual 2013 07 11 18 26 42 Pn i amp Please Note When the internal HDD is not connected or an error occurs the character H will appear on the first channel of the live screen and accompany buzzer alarm If you want to close the buzzer alarm please enter into Main menu Alarm to set HDD loss and alarm output to off 15 IQCCTV 1Q1920DVR User Manual Chapter 5 DVR Menu 5 1 Pop up Menu After finishing system initialization click the right key of mouse on the main interface mode to enter into Pop up Menu In this menu the user can change parameter setting and operate the Main Menu Multi Pics PTZ Auto Cruise Zoom in out Rec Search Manual record Sequence PIP and Vo Switch Click the 0 key on the remote controller or hold Esc key on the front panel to switch the system to other output device 2013 07 11 18 26 42 Pn hHee 20 OOM 5 2 Main Menu Guide Please see the following page for the main menu guide 16 IQCCTV Display Record Search Network Alarm Device System Advanced 1Q1920DVR User Manual Live set Output Set Privacy Zone Record Parameters Schedule Main Str
31. cent Documents C Desktop ti My Documents gt My Computer i d My Network File name DVR16C_V130621V130401V130623V130624 gt aces Files of type fan Files Cancel B Click the Start update button and the processing bar will display the current upgrade status Load Default Recover defaulted parameters of the DVR remotely Please note that the details in this setting should be consistent with DVR local setting Remote Setting Local Setting Load Default Save Device B system B Advanced Motion Alarm Maintain Events Firmware Update 62 IQCCTV 1Q1920DVR User Manual Events The events section allows the user to configure abnormal type buzzer output time alarm email and the message shown in alarm screens Please note that the details in this setting should be consistent with DVR local setting Remote Setting Events Refresh Event Type M Show Message Send Email E Alarm Out Maintain Allows the user to set auto system maintain for DVR remotely Please note that the details in this setting should be consistent with DVR local setting Remote setting Local Setting hd A P Advanced Motion vents 6 3 4 Local setting Under the lt Local setting gt option the user can set the record path of any recorded file Live record and Playback clip file In addition the user can set the download path of remote file Snapshot path File type H 264 and AV
32. ch allows the user to select lt Exit full screen gt amp Toggle between original proportions and Adaptive Screen Resolution C e E G E EE MAAR CH Split mode 49 IQCCTV 1Q1920DVR User Manual 6 3 1 2 PTZ Control m 012345678910 ZOOM FOCUS IRIS O Preset Ludi Cruise Lh 1 PTZ moving Direction control Control PTZ camera s direction The middle button allows the user to Auto cruise Om eee P TZ speed control bar Adjust video Hue Adjust video brightness Adjust video Contrast Iris Focus and Zoom control d Preset setting clear Start cruise stop cruise 6 3 1 3 Video control Adjust video saturation E MEE V Ell Recover ex factory default value STRE 50 IQCCTV 1Q1920DVR User Manual 6 3 2 Playback Click the meaa icon to enter into lt playback gt menu 6 3 2 1 Record search To search for a record select the day you want to check and check the lt synchronous Playback gt button and the channels that you desire to view Then select a record type Normal record Alarm record and All and click lt ma gt button Please note On the time axis the red part stands for alarm record yellow stands for normal record and the original part stands for no record during this period To playback the desired channel tick the corresponding box on the left of the screen Alternatively to playback selected channels at the same time select the
33. eam Record Search Record Plavback Clip Set Backup Event Search Log search Network Set Sub stream Email Set Mobile Set DDNS Set Motion Detection Alarm set PTZ set Serial Set General Users System Information Maintain Event 17 IQCCTV 1Q1920DVR User Manual 5 3 Main Menu On lt Live gt mode click the Menu button on the front panel or Remote controller to enter into the Main menu interface In Main Menu mode you can control device management settings such as Display Record Network Search System and Advanced setting 5 3 1 Display 5 3 1 1 Live mode To enter the Live Mode menu go to Main menu Live option and enter into the Display setting interface shown as below Channel Choose which Channel to view Name Change the channel name allows up to 8 characters Position Setup the display position of each channel Color Click Setup option to enter into the Colour setup interface shown as Picture 5 2 Covert Enable Live surveillance screen Show time Enable the system time to appear in the lt Live gt screen Record time When the record time is set to Enable you are allowed to record the system time into the recording history Copy Copy all data of one channel to any other one VVVVVV WV Y COLOR SETUP HUE BRIGHT CONTRAST SATURATION Default Apply Picture 5 2 18 IQCCTV 1Q1920DVR User Manual 1 Click APPLY button on the
34. er name and password provided by ISP and set the Media and HTTP port To gain access to the DVR remotely via the public network by using the IP address captured after registering a domain name and HTTP port I ij 1 Network Sub Stream Emall DDNS Mobile Port 1 8004 DNS 1 DNS 2 000 000 000 000 Auto Port Forwarding Enable w Default Apply When selecting the 3G option from the Type drop down list please follow the below steps to configure 1 Input the Mobile Port 2 Click lt Apply gt and the System will automatically capture IP 3 Enter the IP address or web port to view the DVR remotely Under the above four net mode you can view the DVR remotely via DDNS and apply for free DDNS account from the websites www 3322 org or www dyndns org I Network Sub Stream Emall DDNS Moblle Port 18004 192 168 001 001 000 000 000 000 o Port Forwarding Enable Default Apply 31 IQCCTV 1Q1920DVR User Manual 5 3 4 2 Mobile Set The IQR DVR range is currently compatible with mobile phones running Android Windows Mobile and Symbian operating systems As well as iPhone and Black berry on 3G networks To configure please follow the steps below 1 Configure the network parameters To do this please refer to section 5 3 4 1 2 Configure the mobile port no such as 19011 and the port that you want to forward to Please refer to Section 5 3 4 3 3 Save the parameters and exit the Main Menu Restart the
35. et Enter the Network by going to Main menu Network gt Network and be presented with the screen below I E Network Sub Stream Emal DDNS oy Type DHCP Mobile Port 1 8004 Ie Client Por etl tide hr IP Address Subnet Mask Gateway DNS 1 s DNS 2 i Auto Port Forwarding Enable w Default Apply After selecting network mode the user can enter details such as DHCP PPPOE or static allocation The user can also view the DVR remotely through the network or internet by setting up the web port UPnP Universal Plug and Play Function If the router supports UPnP function the user can set lt UPnP gt to Enable which will automatically forward port to the router DNS The DNS server is generally provided by local ISP therefore please enter the IP address of your DNS I j Network Sub Stream Emall DONS i Type Statii w Mobile Port 18004 Ie Client Port 09000 HTTP Por 00080 4 IP Address 192 168 001 100 _ Subnet Masi 255 255 255 000 sateway 192 168 001 001 DNS 4 192 168 001 001 DNS 2 000 000 000 000 Auto Port Forwarding Enable Default Apply 29 IQCCTV 1Q1920DVR User Manual When selecting the DHCP from the Type A the router will automatically allocate an IP address for your DVR After restarting each time the IP address captured by your DVR may be different Therefor port forwarding is required when you visit a remote DVR To do to this SEU bx E I
36. etwork is unstable Frame rate allow you set net transmittal frame rate User could select the relative value by pull down menu gt Bit rate allow you set net transmittal bit rate User could select the relative value by pull down menu gt Audio When tick selecting the option system will record video and audio simultaneously I j E Network Sub Stream Emall DONS CH Video PPS Bitrate Audio 01 Enable Enable 03 Enable Enable Enable Enable Enable 08 Enable 64 w 64 w 64 w 64 w DEL d 64 ww DEL 4 4 44 4444 64 w MEIEIEIEIEIREIA un P ad Default Apply 5 3 4 5 Email set Click Main Menu Network Email option to enter into the email set interface as shown below Network Sub Stream Emal DDNS Email Disable SSI v Disable Enable SMTP Port SMTP Servet Sender Emall Sender PWD Recelver Email Interval Default Apply 33 IQCCTV 1Q1920DVR User Manual Choose to enable the Email function by choosing Enable from the drop down menu 2 SSL This is a security link transport protocol You can encrypt your communication info N En rap op including your email using SSL to prevent hackers from monitoring your email or communication info and even your password Set the SSL to On via Gmail com server and set to Off via other mail server SMTP Port indicate one kind of mail transmittal port opened by Simple Message Transfer Protocol SMTP The
37. hedules check the box of the record status you want Alarm General or No Record and then click on each box in the schedule time line that you want Click the Copy To pull down menus and Copy button to copy settings from one day to any other day REC Para Schedule Main Stream Channel GH1 w Copy Sun Y To All v Copy Copy CH1 w To All Te Copy Default Apply 21 IQCCTV 1Q1920DVR User Manual Once the desired time schedule has been selected click the APPLY button to save the options To restore to factory default settings click the DEFAULT button Please Note Under the lt record gt menu and lt search gt menu original color stands for no record Red stands for alarm record yellow stands for Motion record and Green stands for normal record 5 3 2 3 Main Stream Go to Main menu Record Main Stream to enter into the interface as shown below lj gt REC Para Schedule Main Stream Resolution FPS Clr CIF 03 CIF Cl Clr b d b d v v v v v v Co To go to the settings menu in the HD SDI DVRs enter Main Menu Record Main stream to enter into the interface gt Resolution Supports 1080P Save and exit the main menu The system will restart when the settings are saved Record Resolution Supports 1080P Frame Rate PAL 1 25 fos NTSC 1 30 fps Bit Rate Local record bit rate The user can select the relative value by pull down menu Audio When selecting the Audi
38. interface as shown below Only the Admin user is authorized to set common user s authority WON NON NO NONO N VV WV HDD PTZ General Users Info USERNAME user Log Search Parameter Maintain Disk Manage Remote Login SEQ Control Manual Record Backup XE 04 05 06 07 08 09 t0 IEEE E 15 16 Live ot o2 o 4 05 06 07 08 09 1 0 1 JEL E 15 16 Playback XE 04 05 06 07 08 09 DE JEL E 15 16 PTZ Ce elaine DII GE PE GED DICE GE RSEN EE KE Apply Log Search Check all the system logs Parameter Set all the parameters Maintain Update the version recover ex factory value reboot and shut down the DVR Disk Manage Manage and control the HDDs Remote Login Remote login DVR Rotate Control Sequence the live screens for all the channels Manual record Manually start stop recording Backup Check this box to be allowed to backup the record of all the channels Live Check this box to be allowed to view all the live images for all the channels Playback Check this box to be allowed to playback the a selected record PTZ control Check this box to be allowed to perform the PTZ operation for any selected channel 5 3 5 5 Information Click the Main Menu System Info to see the DVR information as shown below D p i l HDD PTZ General Users Info Device Name DVR 160 Device ID Device Type Hardware Version Software Version IE Client Version MAC Address 38 IQCCTV 1Q19
39. k if the Remote Controller is broken 7 Q Can we record whilst playing back A Yes The system supports recording whilst playing back 8 Q Can we erase some recorded files from DVR A Considering the safety factor you can t delete the recorded file directly from the device To erase unwanted files please select HDD format function 9 Q Why does the Buzzer keep sounding A Please check if motion detection is on and the system has detected motion make sure the HDD is being detected and has sufficient space available Check if the DVR is receiving video 19 IQCCTV 1Q1920DVR User Manual Appendix 4 Usage Maintenance To maximize the use of your new DVR please follow the steps below 1 2 3 el Close the OFF button on the front panel to avoid losing data Make sure DVR is kept away from heating source Clean the internal dust regularly and keep the DVR in a place where there is good air circulation Do not plug in RS 232 and RS 485 when power is on to avoid any damage to the port Check the HDD cable and data cable to avoid the cable aging Avoid other electronic devices interfering with the video audio signal of DVR In addition avoid static electricity and induced voltage damage to DVR It is suggested that the user replaces the BNC cables regularly to keep the signal input stable 76 IQCCTV Appendix 5 Accessories 4 8 Channel Accessories DVR 1x DVR Power Supply Software CD 1Q1920DVR U
40. low sy Pl 43 8 51 am Device Manager Add Device Manager dvr_1 gt Device Name DVR DVRtest gt NY Login Address 192 168 1 11 Media Port 9000 User Name admin Pad sess Channels 8 Press to get channel number 68 IQCCTV 1Q1920DVR User Manual To add a new device click Add button at the top right then you can input the device name Login address ip or domain name Media port user name and password etc The Channels property can be retrieved form device To delete a device from list swipe the device name you want to delete then tap the delete button next to the device name Live video monitor Tab Live Monitor on Main Menu will bring up Live interface which provides stream video record snapshot and PTZ etc unknown Open a device Tab the button to open the device list as below then select one of devices in the list This will open all channels in the list automatically an Ml 3 9 00 am Back Channel Config Q dvr Open a channel Tap the cross button on one of the view windows to enter the channel list window Once in the channel list menu select one channel to open to view 69 IQCCTV 1Q1920DVR User Manual an P E 9 01 am Back Channel Config o ws 1 es 3 f 4 Recording streaming The user can record streaming when viewing the live video Tap the button and then tap the channel label on the bottom panel to start recording Please note that
41. nual 2 1 1 4 8 Channel DVR Front Panel Key title or Indicator Power Indicator PWR HDD HDD Indicator Channel select CH1 CH2 CH3 CH4 FWD Right Key Up key PTZ Enter All channel display REW Left Key Function amp Description If the Green indicator is on the system is getting power normally Receives IR signal from Remote Controller When the Red indicator flashes it means the hard drive is being read or Recording CH select key Move to left Rewind function Decrease PTZ rotation speed and parameter value On preview mode hold the button to switch GUI operation device Right key increase PTZ rotation speed and parameter value and fast forward Move down In the Menu press this key to enter Not in the menu PTZ operation Display all channels IQCCTV 1Q1920DVR User Manual Play Pause Play record file Pause record file Rec Stop Begin record stop record Menu ESC Enter into main menu exit Menu MENU ESC IQCCTV 1Q1920DVR User Manual 2 2 Rear Panels 2 2 1 4 8 Channel DVR Rear Panel 1 4 11 10 5 6 9 emm mmm Connect CH1 4 or 1 8 Virtual video input device CBNC S USS Poe Gomes USB mouse VGA Port Connect to VGA monitor such as PC monitor Optional M RS 485 Sensor Alarm RS485 Sensor Alarm interface Alarm Interface on 8 Channel Ethernet Port Connect LAN Ethernet RJ45 interface HDMI Port Connect HDMI IR EXT IR Extension IQCCTV 1Q1920DVR User Ma
42. nual 2 2 2 RS485 Sensor Alarm port functions Alarm input Connect port of your sensor to G GND pin and port to channel input according to the alarm device you purchased Alarm output Connect to the two ports marked with out e PTZ Port Connect your camera to RS 485A and RS485B accordingly 2 3 4 8 Channel Remote Controller 5 MALAE NNNM Y Down arrow owiencw ir uin dE Volume adjust Left Down ne mL enean OOOO f Scam eeoprtn O Confirm the selected operation 9 jRewndky o O 10 Enter into record search menu Play key Hr re Fowadky o O OO H2 fe Reomky OO oO as M PaweGequmeky O O o 4 w Stop manual record stop playing 10 IQCCTV 1Q1920DVR User Manual 2 4 Mouse Operation In menu lock mode Enter into pop up menu and click any sub menu to go into the Log in window In menu unlock mode Enter into pop up menu and then clicking left key to enter into any sub menu directly After entering into main menu click the left key to enter into any sub menu On Detailed file menu mode click the left key to playback one recording file Mouse Click the combo box to access pull down menu Click left key to stop By clicking left key you can adjust the colour control bar and volume control bar Clicking combo box to access pull down menu By clicking the left key you can select values in edit boxes or pull down menu Mouse supports special
43. o option the system will record video images with audio simultaneously VV VV 22 IQCCTV 1Q1920DVR User Manual 5 3 3 Search 5 3 3 1 Record Search Click the Main Menu Search Record Search to enter into the interface as shown on the following page gt gt Channel Select the channel s that you desire to search Date Search In the Video Search screen the user can search for all the records in a specific date To execute a video search highlight and select the date numeric field and then click the desired time of a recorded even on that specific date i Record Search Event Search Backup Log CH All iv Time Search In the Search screen the user can search for a specific date and time for a recording and view it in Playback mode This is useful for hunting a specific recording of an incident if you know the date and time it occurred File List Click the File List button to enter into the Event Search screen shown The video records for the time you have chosen will appear in the screen Playback Mode You can use the Playback Control bar to operate the Fast Forward X2 X4 and X8 Slow play 1 2 1 4 and 1 8 speed Play Pause Frame Rewind X2 X4 and X8 When ending the playback the DVR will return back to previous menu shown Play control Bar The play control bar will display current playing processing When the user clicks any time at the control bar and this point have not any record file the sys
44. ode U 1x1 display mode 1x2 display mode 5 8 Record search Enter into the Record Search menu from the Pop up menu to conveniently and quickly search playback the recorded files To find out how to search through recorded files see section 5 3 3 1 5 9 Mute Click the o icon or press lt Mute gt button on the front panel and Remote controller to control the mute of DVR 44 IQCCTV 1Q1920DVR User Manual 5 10 Manual Record To start the manual record function click ES button on the Front panel or Remote controller Please stop recording manually once manual record is activated 5 11 Stop record To quickly stop recording click the icon or Stop button on the front panel or remote controller 5 12 Start Sequence In the single mode enter into the Start sequence menu This will initiate the auto sequence function at the set interval For full details please refer to section 5 3 1 2 5 13 Start Cruise If multiple presets are specified the PTZ camergewill automatically move to the entire preset at a time whilst user activates the Start Cruise options To stop the cruise please click Ball icon on the Tool column 45 IQCCTV 1Q1920DVR User Manual Chapter 6 Web Application 6 1 ActiveX Control Download and Installation Open your web browser and input the IP address and web port of DVR for example http 172 18 6 202 8080 If your computer is connected to Internet it will download
45. only the channels that are viewing can be recorded Recording will stop if you close the channel or leave live page Video snapshot When monitoring live tap the e button to show 5 labels on bottom panel Tapping these labels will enable the user to take snapshots 1 8 54 AM Live Monitor Select unknown uU Remote Playback Tab the Remote Playback on the main menu to bring up a calendar view The calendar will use black points to show days where recording takes place Press the Select Channel button to retrieve the recorded videos of channel from the device 70 IQCCTV 1Q1920DVR User Manual PTZ control 48r Tap the page button to open PTZ mode and bring up the PTZ control buttons at the bottom of live an Pl 43 8 53 am Live Monitor Select To control the camera maximize a camera window and open PTZ mode Tab the arrows on the side of camera window to control camera move side to side or up and down Other control buttons allow Zoom Force Iris PTZ speed and Preset Below shows a list of functions supported in the PTZ control function 9 Zoom In Qi In V on Out Iris Out A Focus In 9 Preset Focus Out PTZ Speed 71 IQCCTV 1Q1920DVR User Manual Appendices Appendix 1 Operation Function Table Time setting Set system date time display format and day light saving time Language select Set system language Set CH title and position adjust image colour Channel setting pa
46. ould be consistent with DVR local setting Refresh Save Free Total G Free Time p Advanced PTZ Configuration shown below Please note that the details in this setting should be consistent with DVR local setting Refresh Channel Protocol Baud rate Data Bit Stop Bit Parity Cruise Address 58 IQCCTV 1Q1920DVR User Manual General This options allows the user to check the DVR s language video system and also set system time date format DST and NTP Please note that the details in this setting should be consistent with DVR local setting Playback Remote Setting Local Setting General Refresh DST NTP Users In the users menu configure the user name and password as shown below Please note that the details in this setting should be consistent with DVR local setting Playback Remote Setting Local Setting Display Users Refresh Yous User Name Password Active Wem pnm User Name ecord feats Bs users Disable Disable TETTE Disable Disable Active user Disable Disable Password Disable hm Advanced 59 IQCCTV 1Q1920DVR User Manual Information Check out device name number type MAC address software version IE version and hardware version Playback Logout Display Device Name Record Device ID Network Device Type Hardware version System Firmware Version HDD IE Version MAC Address Infa Advanced 6 3 3 5 Advanced Click the
47. p the date to playback the recorded files Recording streaming The IQCMS apps allows the user to record streaming when viewing live video To do this tap the ux button and then tap channel label on the bottom panel to start recording Please note that only the channels which are viewing can be recorded Recording will stop if you close the channel or leave live page Video snapshot When in live monitoring mode tap the Ol button to show up 5 labels on bottom panel This will allows the user to take snapshots by tapping the labels uiii gt 18 25 MENU Live Monitor PTZ control A EL PTZ is Pan Tilt Zoom and reflects the movement options of the camera Tap the button to open PTZ mode This will bring up PTZ control buttons on the bottom of live page 67 IQCCTV 1Q1920DVR User Manual Android 1 Connect your Android phone to the internet using 3G or WIFI 2 Download and install the free IQCMS app from the Google Play Store 3 After finishing installation the IQCMS icon will be displayed to phone interface shown as Picture 2 4 Tab the IQCMS icon to open the app A OO 4 24 am IQCMS e Live Monitor c 2 Remote Playback p Record Playback R Image View w Device Manager e Help Picture 1 Add and delete device The device manager allows the user to add or delete device and also modify device properties Tab the Device Manager in the Main Menu to open the interface as shown be
48. rameter value set CH display to ON Off and time display recording time overlaying to On Off Set image quality resolution volume record mode an Record setting pud uiia pack time Time based search channel based search and rec Record search Basic mode based search settin Specified time playback scheduled playback file list J Record Playback aoa i i d oc playback IET imos Ey play ome by frame multi speed forward and multi speed rewind U flash disk and removable HDD backup and network File backup download Check HDD status usage space setting HDD HDD Manage auto overwrite Adjust VGA resolution select system and volume VID AUD Setting control set interval and channel display Set or modify user password Set HDD loss HDD space video loss l O status Alarm setting alarm management and Email alarm oet on off status of MD select sensitivity and set Motion detection motion detection area Select CH and set PTZ protocol baud rate and PTZ PTZ setting Advanced address for the CH Setting Mobile oet user name password and server port surveillance Set system auto maintenance maintenance time regularly system upgrade ex factory default value recovery and manual restart system PIP display Zoom in out split mode auto sequence Display mode i and cruise display Network Network and Port Select network mode and set net viewer port web setting setting port DNS and DDNS parameters Live display Rea time video
49. record will last after the alarm ends 30s 1minutes 2minutes 5minutes gt Copy Copy current channel parameters to any other channel or all channels Yv v The channel will be separated into 44x36 grids PAL NTSC mode When an object moves into the motion detection area and the area where the object is located is displayed in red then motion detection will be triggered In the semi transparent area the motion detection is not activated After configuring the above parameters click lt OK gt to save it 39 IQCCTV 1Q1920DVR User Manual 5 3 6 2 Alarm Set Click the Main Menu gt Alarm Alarm to enter into the Alarm menu Below This menu allows the user to set alarms based on different statuses ji T Motion Alarm Maintain Events oy Alarm In CH1 Alarm Type NO v Ie Alarm Out Latch Time 105 iw Show Message V Buzzer Orr ww Send Email w Full Screen Record Channel Post Recording 30S Sci oa EDS DIG Gs UIS DUE GE RE E US Copy CH1 To All v Copy Default Apply gt No Select one desired channel gt I O Status Choose between the following three options NO Normal Open NC Normal Close and OFF Set to Normal Open the I O status Alarm will be activated while sensor is ON Set to Normal Close and the I O status alarm will be activated while sensor is OFF Set to OFF and the I O status alarm will not be triggered gt Alarm out Connect an external alarm sensor
50. ser Manual User Manual 1x USB Mouse 1x Remote Control f Manufactured for J CCTV Y UD CE RoHS TECHNICAL SUPPORT For technical support please contact your local distributor Alternatively call 0871 222 1430 LIMITED WARRANTY This product is supplied with a 12 month warranty The warranty excludes products that have been misused including accidental damage and damage caused by normal wear and tear In the unlikely event that you encounter a problem with this product it should be returned to the place of purchase IQCCTV Unit 2 Valley Point Beddington Farm Road Croydon Surrey CRO 4WP www iqcctv co uk
51. ssword The Channels property can be retrieved from the device To delete a device from list swipe the device name you want to delete then tap the delete button next to the device name Live video monitor Tab Live Monitor on the Main Menu to bring up Live interface which provides stream video record snapshot and PTZ controls as shown below 18 25 Live Monitor 65 IQCCTV 1Q1920DVR User Manual Open a device Tab the button to open device list as below then select one of devices in the list This will open all channels automatically 10 13 AM Open a channel Tab the Cross button on one of the view windows to enter the channel list window After select one channel to open on the previous window uil D Lie Monitor Select channel DVR1 Port 9000 Address 192 168 1 41 CH1 CH2 CH3 CH4 CH5 CH6 CH7 Cgceeaegce Remote Playback Tab Remote Playback on Main Menu will show the playback entry You will be able to play one channel of remote device after 2 steps 4 3 JAN 2013 gt SUN MON TUE WED THUR FRI SAT lie 3 4 5 6 7 81 9 10 11 12 13 14 15 16 17 18 19 EJ 21 22 23 24 25 26 27 28 29 30 31 Select channel 66 IQCCTV 1Q1920DVR User Manual 1 Select one channel Select the channel button to open device list and then select the desired channel of device in the list 2 Select date When you have selected channel all the dates with recorded files will be marked with a dot Ta
52. surveillance remotely Network Set record mode and status of DVR remotely Remote playback Check local record history via network Function PTZ control Remotely control PTZ camera position focus zoom and iris etc 72 System maintenance IQCCTV 1Q1920DVR User Manual Remote Set local CH display record alarm PTZ control parameter set of parameter value via network DVR optional parameter value of previous menu Default Recovery Clicking the button will The option will be recover current parameters to effective after clicking system defaulted value Enter button Menu button Clicking the button will exit the current menu Time setting Adjust system time Format HDD The option ill be HDD Manage ie M effective after restart oet network type and web Basic ee port except of PPPoE other application Net setting i type need forward web port to The option will be Guide router of DVR effective after restart System Info Modify MAC address Mobile Monitoring Set relative parameter PTZ setting Record set and Language select etc 73 IQCCTV 1Q1920DVR User Manual Appendix 2 Alarm Record Setting Under the record mode li icon or EI icon will appear on the screen and an alarm will be issued If the user has configured the record type to Normal on the Scheduled mode once one alarm has occurred the record will be saved as Normal record However if the user has configured
53. symbols numeric and character input Use instead of Enter i or Backspace e In live display mode clicking right key will display pop up menu Click right key of l menu Double click Left In live display or playback mode double clicking left key will maximize the screen Select menu item Sliding Mouse On motion mode sliding mouse will select motion area On Colour set menu mode sliding the mouse will adjust colour control bar and volume control bar 11 IQCCTV 1Q1920DVR User Manual Chapter 3 DVR Connection 3 1 HDD Installation Caution Please do not Install or take out hard drive when DVR is running HDD Installation 1 Cut power to the DVR 2 Unscrew the screws and open DVR upper cover carefully 3 Insert the Power Cord and data cable into Pin of hard drive securely 4 Remove the screws on the HDD bracket 5 Fix the HDD to the bracket and then fix the bracket with HDD to DVR body 6 Put the upper cover back carefully and re attach the screws Please Note If the user requires a higher performance HDD please contact the place of purchase 3 2 Camera and Monitor Connection To connect camera a cable to the BNC video inputs at the rear of the DVR To connect the DVR to a monitor via the HDMI VGA Video output connection If the camera is a PTZ speed dome you can connect the RS485 A amp B to the corresponding port of the DVR refer to system figuration on Chapter 8 12 IQCCTV 1Q1920DVR User M
54. system 5 Enter the user name and password The details of the mobile will the same as the DVR 5 3 4 3 Router s Port Forwarding Port forwarding is required when you want to access the DVR connected to the router from outside of the router s network If PPPoE is selected port forwarding is not required 1 Input the router s IP address from an Internet Explorer based browser to open the Router configuration interface 2 Choose the Transmittal rule option to take you to the port forwarding instructions to your router 3 The DVR IP address for the intranet should be lt 192 168 1 101 gt Forward Media port 19009 and HTTP port 19010 to this IP address respectively 4 Once this has been done the DVR can be viewed remotely Please Note The router s port forwarding interface may be different when entering into a virtual server The user will always need to forward port range 1025 65535 the router to the IP address of DVR allocated or automatically captured Select All or Both in corresponding protocol column and save the above setting The above steps may differ from the router device depending on the manufacturer 32 IQCCTV 1Q1920DVR User Manual 5 3 4 4 Sub stream Go to Main menu gt Network gt Sub Stream to enter into the interface shown as Picture 5 32 Video allow you open or close the sub stream output If you select Enable system will select sub stream preview and guarantee image quality once n
55. tem will auto return back to previous menu 5 3 3 2 Channel Select Then tick select the channel you want to playback and click Play button to enter into the playback mode as shown below 23 IQCCTV 1Q1920DVR User Manual 5 3 3 3 Time Axis setup file clip and zoom in out 1 The DVR supports the processing control bar function when playing back record files as shown in Picture 5 12 Up to 4 CH is available 2 Click d icon beside the processing bar to pop up the interface shown as Picture 5 13 Picture 5 12 Picture 5 13 Time Axis Defaulted to 24hours The user can select 2hours 1hour 30 minutes or user defined The detailed operation is as follows 15 Fixed time axis If you select the E option the processing control bar will cover two hours of video content 2 User defined Select the EB joption and move the cursor to processing bar to select start time and or end time Now the whole time axis equals the time of recording you just selected Record Clip and backup function and Zoom in out function BACKUP CONFIRM From 00 00 01 To 23 59 59 Total files 4 Total size 1706 MB Are you sure to backup Backup Cance Picture 5 14 Picture 5 15 24 IQCCTV 1Q1920DVR User Manual gt Clip and backup When one channel is playing back the Econ will appear in the Play control bar as shown in Picture 5 14 Click the icon to start video clip function then click it again to end the function
56. terface shown as Picture 5 40 to configure the DST status and mode Click the NTP setup to enter into the interface shown as Picture 5 41 to enable disable the NTP function l p i p HDD PTZ General Users Info ennid I j HDD PTZ General Users Info itt n DST Enable lw Enable Disable Time Offset I Hour E Daylight Saving Time Weel Iv Start Time Mar End Time Nov Server Address poolntp org Y Time Zone GMT 0500 v uA un v 02 00 00 Picture 5 40 Picture 5 41 Please Note The above NTP function change will only be available when the system is connected to the Internet When the NTP function is set to Enable the system will calibrate the time at every 00 07 50 and every start up 5 3 5 4 Users Click the Main Menu System users option and then enter into the interface as shown in picture 5 42 LEVEI ENABLI ADMIN ENABLI admin 2 SEI USERI DISABLE T ble w 3 user2 USER2 DISABLE oe 4 users USERS DISABLE 5 Wistal ke USER4 DISABLE USERS DISABLE ONOOOOO s USERS DISABLE g gt Default Apply Exit g gt Edit Picture 5 42 Picture 5 43 The model supports up to seven users with one Admin and six users Click the Edit button to enter into the User Edit interface as shown picture 5 43 3 IQCCTV 1Q1920DVR User Manual Select one lt common user gt and click lt Apply gt Then enter into the lt Authority set gt
57. tput port or HDMI Output Supports net viewer and MP live surveillance and also supports zoom in out auto sequence and PIP display H 264 video compression format The recording quality resolution and Recording frame rates are adjustable to user s needs Multiple recording modes Constant Scheduled Manual Alarm Motion detection and remote record Recordin J Supports a 3TB SATA HDD and saves real time recorded images to HDD otorage Ellos nd DVR single CH and multiple CH Search Playback of recorded Real time monitoring DVR backup via USB flash drive removable drive Recorder and network Supports HDD amp video input alarm management and external alarm signal Alarm Setting up i up 9 inputs 8 Channel Only Network Supports remote surveillance by admin users to increase system security Operation Mouse Supports Mouse operation for faster menu navigation Operation PTZ Control Supports PTZ camera operations through RS 485 1 1 Features H 264 video compression format supports 1080P resolution G 711 audio compression format HD 960H WD1 WHD1 and WCIF Recording Playback Embedded real time Linux2 6 operation system VGA and HDMI Outputs Multiple alarm record modes Rear USB2 0 ports for back up recorder upgrade and mouse operation Backup with USB network or DVD Optional Mobile Phone Access Multiple language OSD Support auto maintain IQCCTV Chapter 2 Overview 2 1 Front Panels 1Q1920DVR User Ma

User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents