SAXON USER MANUAL
Contents
1. CSOO color selections SUB slave mode TECHNICAL SPECIFICATIONS Power supply 9O 240V AC 50 60OHz Power consumption MAX GOW Fuse 25OV 1OA DMX control channels DMX 512 connection 3 pin XLR Number of LED 4 MCD LEDs Flash rate max 1O Hz ITEM DIMENSION 240 230 240MM ITEM WEIGHT 3 OKGS Please note Information is subject to change without prior notice2. carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance centre Always use the same type spare parts Please read carefully the instructions which includes important information about the installation usage and maintenance Don t connect the device to any dimmer pack Do not touch any wire during operation as high voltage might cause electric shock Features Four operation modes DMX 512 protocol auto and master slave and sound active operating in various modes to form different led effects DMX 512 connection connection between fixtures XLR connection F you are using controllers with this light you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain F you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected Optional At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture Connection with the mains Connect the device to the mains with the enclosed power supply cable OPERATION 1 DMX 512
3. SUC LIGHTING CO UkK SAXON USER MANUAL INTRODUCTION Thank you for choosing this Cue Lighting item Before you start please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device SAFETY INSTRUCTIONS CAUTION Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect mains power before fuse lamp replacement or servicing Replace fuse lamp only with the same type Make sure there is no flammable materials close to the unit while operating as it is fire hazard Use safety cable when flying this unit Maximum ambient temperature is TA 4O C Don t operate it where the temperature is higher than this In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs
4. protocol Addressing The LED DISPLAY on the rear side of the base allows you to assign the DMX fixture address which is defined as the first channel from which the item will respond to the controller IF you set for example the address to channel 7 the item will use channel 7 to 14 for control Please be sure that you dont have any overlapping channels in order to control each item correctly and independently from any other fixture on the DMX data link IF two three or more items are addressed similarly they will work similarly At DMX mode you can choose the address from 1 to SI2 After you connect the item to the mains the item starts running When the item finishes resetting d OO will flash in the led display you can then set the desired DMX address by pressing the UP or DOWN buttons Eight DMX channels Channel Imotor running O 190 Motor running directions adjustments 191 255 Motor running Channel 2 red from small to big brightness dimmig Channel 3 green from small to big brightness dimmig Channel 4 blue from small to big brightness dimmig Channel 5 white from small to big brightness dimmig Channel 6 master dimmer from small to full brightness Channel 7 increasing brightness then decreasing brightness colors following one by one O 36 CHI 2 35 4 5 6 working 37 73 four colors increosing brightness then decreasing brightness 74 100 four colors changing M 147 mixed colors increasing brightness then decreasing brigh
5. tness 146 164 mixed colors changing 165 255 strobe from slow to fast then from fast to slow when ch2 3 4 5 6 working Channel 6 running speed adjustments O 244 speed from slow to fast when ch7 at 57 164 the speed adjustment works 255 sound active 2 Sound active Press the MODE button till BEAT shows in the led display confirm by pressing ENTER then the item will run to the beat of music 3 Auto Press the MODE button the following functions can be achieved by pressing ENTER PO O run the preset shows PO P4 means 5 preset shows O to 9 does color changing 10 speeds CF O increasing brightness then decreasing brightness CF O to CF 9 means 10 running modes CC O color changes CC O to CC 9 means lO running modes CSOO color selections CSOO to CS99 means 100 colors L Synchronization amp master slave mode Take one item and set the item at sound active or auto as above then get other items and press the button MODE till SUB shows in the led display confirm by the button of ENTER then connect the items to the item at auto sound active already set by DMX cables disconnect the items from DMX controller the items Will Wok simultaneously the item at auto sound active as master the others as slave LED DISPLAY DOOI DMX setting BEAT sound active PO O preset shows PO O to PO 9 color changing speed modes CF O increasing brightness then decreasing brightness CC O color changing
Download Pdf Manuals
Related Search