DVR User Manual
Contents
1. 3 4 Observing the Cameras e Selecting Cameras Number Cam o Input the camera ID and then press the Cam key to select a camera in the network 3 5 Dome lens control e Zoom to Zoom users can control the zoom by rotating the joystick clockwise anticlockwise e Focus Used in bringing objects into clear visibility The following buttons can be used o Press Far key to focus far objects o Press Near key to focus nearer objects METAN Normally the dome will adjust the zoom and focus controls automatically The Far and Near keys are used to manually zoom and focus the camera e Iris Used to control the amount of light coming through the camera lens Users can use the following buttons o Press Open key for manual iris accretion A full white picture means maximum iris is selected o Press Close key for manual iris reduction A full black picture means minimum iris is selected 17 AMI XSDZ 3DM User Manual M vision 3 6 Set Dome Function 3 6 1 Preset e Preset Set N Pre N represents the preset number o Press Set key and then input a number for the defined scan and press the Pre key e Call Preset N Pre o Input the preset number and then press Pre key 3 6 2 Scan e Left borderline Set 1 Scan e Right borderline Set 2 Scan e Start scan 1 Scan MECANO Enter the menu to setup these options when you need to change the scan speed refer to section 3 7 3 6 3 Pattern e Design path2. 3 Run scan dome scan Set left 1 Set right limit Run scan left limit right limit Press enter sure Press enter sure Press prev to back Press prev to back Success Ser dome pattern Set pattern Run pattera 1 pattern num Press I to start 2 Set pattern Press 0 to start Success 3 Run pattern Press prev to back Set dome tour Insert preset Run tour 1 Tour num 1 Preset mun Insert preset 2 speed Success Run tour 3 Dwell Cam1D 001 Mon 1D 001 Protocol Factory Matrix Pelco matrix Baudrate 9600bps 123 sft 1 Pelco matrix 3 Pelco d cess 2 DH DYR Success Dome 1 Factory 2 Pelco p Success 37
3. Run pattern After entering the menu input the pattern number you want to create You can put in the Numbers 1 4 and press Ent The selection will skip to the next item automatically to set the pattern you need If you already have it you can skip it and press the number 3 to run the pattern directly Pattern setting Press number 2 to enter the Set Pattern page Move the dome to a start position and press the 1 button to start recording the pattern Fig 4 2 3 2 The LED screen will display Start at the bottom of the page Press 0 to finish the record the pattern If successful the text lt Success gt will be displayed and then revert back to the previous menu Select option 3 to run the pattern Press 1 to start Press 0 to finish Figure 4 2 3 2 Press PREV to back 28 AMI XSDZ 3DM User Manual M vision MECANO Under this mode operating the keys and moving the joysticks will not control the domes 4 2 4 Tour Setup Enter the main menu as in Figure 4 1 1 1 Press the number 2 button to enter the Dome Setting menu figure 4 2 1 1 Press the number 4 button to enter the tour setting menu figure 4 2 4 1 1 Tour Number Figure 4 2 4 1 2 Insert preset 3 Run tour After entering the menu you need to input the TOUR information Input the number i e between 1 6 and press the Ent button to confirm The selection will then auto skip to the second TOUR setting The text lt Su
4. 2 Set Baud rate 2400bps Figure 4 1 2 1 MECANO Under the IR communication mode the Baud rate must be set to either 2400bps or 4800bps Select the Baud rate you need and press the Ent button to save any changes If successful the text lt Success gt will be displayed Press the Prev button or move the joystick to LEFT to back to previous menu METAN When using a multiple keyboards setup such as a matrix the baud rate must be set to either 9600bps or 19200bps 23 Pa gt XSDZ 3DM User Manual M vision 4 1 3 Joystick Adjustment To adjust the joystick settings the user needs to enter the menu for the Joystick Calibration menu Please ensure the joystick is in a neutral state The steps are as follows Enter the main menu as in Figure 4 1 1 1 Press the number 1 button to enter the Keyboard Setup Press the number 3 button to enter the Joystick Calibration settings as in Figure 4 1 3 1 Joystick is free Then press Enter Figure 4 1 3 1 Press Ent to finish the joystick calibration If successful the text lt Success gt will be displayed 4 1 4 Display Keyboard Information Enter the main menu as in Figure 4 1 1 1 Press the number 1 button to enter the Keyboard Setup Press the number 4 button to check the keyboard information 4 2 Dome set up 4 2 1 Preset set up Enter the main menu as in Figure 4 1 1 1 Press the number 2 button to enter the Dome settings menu fig
5. 4 2 1 6 Press PREV to back Input the preset number that you would like to clear and press the Ent button If successful the text lt Success gt will be displayed and then revert back to the previous menu 4 2 2 Dome Scan set up Enter the main menu as in Figure 4 1 1 1 Press the number 2 button to enter the Dome Setting menu Press the number 2 button to enter the Dome Scan Setting menu as detailed below 26 AMI XSDZ 3DM User Manual M vision 1 Set left limit 2 Set right limit Figure 4 2 1 1 3 Run scan Press the number 1 button to set the Left limit as picture 4 2 2 2 shows Press ENTER to save Figure 4 2 2 2 Press PREV to back Move the dome to a suitable position and press Ent to save If successful the text lt Success gt will be displayed and then revert back to the previous menu Press the number 2 button to set the Right limit and follow the same procedure as detailed above Go back to the menu and press the number 3 button to run a scan as you have setup in the above steps MECANO Under this mode operating the keys and moving the joysticks will not control the domes 27 AMI XSDZ 3DM User Manual M vision 4 2 3 Pattern Setup Enter the main menu as in Figure 4 1 1 1 Press the number 2 button to enter the Dome Setting menu Press the number 3 button to enter the pattern setting as shown in figure 4 2 3 1 Pattern Num Figure 4 2 3 1 Set pattern
6. setup Set N Pat Path Set 0 Pat o Press Set key input a number for the defined scan i e 1 4 press Pat key then move the camera along the desired path When finished press the Set key first press O key and then the Pat key MGE Alternatively patterns can be set within the camera s own setup menu 18 AMI XSDZ 3DM User Manual M vision e Starting the pre defined scan N Pat o Input the pre defined scan number i e 1 4 and press Pat key to start 3 6 4 Cruise e Cruising N Tour o Input the predefined cruise number first and then press Tour key this will tour the predefined presets Press the Tour key directly if the system only has one cruise 3 7 Call Main Menu e Calling the Main Menu 9 5 Pre o Input 95 and then press Pre key A menu will be displayed on the monitor The joystick can then be used for navigation i e up down to move through the options and left right to select options 3 8 Matrix Control 3 8 1 Switching the Dome Order The matrix can connect only up to 16 high Speed Domes Information such as the Series Number Time and Date will display on the monitor when you switch from one camera to another e The Prev button switches to the previous camera Pressing the Pre button for 2 seconds will keep the cameras switching through all the 16 high speed domes e Press Next to switch to the next camera Pressing the Next button for 2 seconds will keep the cameras switching back
7. 95 and press Preset to call the menu PELCO Matrix Mode Press Shift and Set to call the Shift Set Matrix matrix menu Press Prev skip to the previous Prev Matrix dome hold on 2 secs on Prev to continuously skip the sixteen 35 De XSDZ 3DM User Manual M vision domes of connection matrix forwards Press Next skip to the previous dome hold on 2 secs on Next to Next Matrix continuously skip the sixteen domes of connection matrix backwards Stop Matrix Stop switch Ent Matrix Alter program press Ent to confirm Input monitor ID press Cam to N Mon Matri PES atx select object monitor 36 XSDZ 3DM User Manual Keyboard setup Keyboard setup Set KB Parameter Set KB 1D Set baudrate 1 SetKB Parameter 1 Set KB ID Input KB ID 1 2400bps 2 About Keyboard gt 2 Set baudrate 4 2 4800bps 3 Joy calibrate O 3 9600bps 4 19200bps Dome setup Protocol setup Exit menu DP About Keyboard Version 1 00 KB ID 008 Protocol Factory Baudrate 2400 O 1 Joy is free then Joy calibrate Press ENTER Dome setup Set dome preset een 1 Set dome preset 2 Set dome scan 3 Set dome pattern 4 Set dome tour 1 Save preset 2 Show preset 3 Clear preset hd o Preset num Press prev to back Set 1 Set 2 Set
8. A alee 7 Functions 8 Characteristics ee 8 Technical Data iii aaa 9 Keyboard Connection uc ii anta Dora 10 RS485 Interfaces 00d A A eee ae ee en eee 10 Direct Connection to Dome ui ds 11 Keyboard Connection through Matrix cect nr nn nr rnnrnnrnnrnnnnnrnnrnnrnnrnnnnnnnnnncnnns 12 Keyboard Operation Instruction oocoococccncccccnconcnncnnannconcnnconnnncannn PLP PL nan PL rnrannrnranannrannnnranannrananncinannss 14 Power Mode insisicicr sir erica 15 LCD Display Screen ia A A a pisa 15 FUNCIONS Of the JOYSTICK 0 pa tdi 16 V XSDZ 3DM User Manual 6 vision Observing the Cameras ioen e eb 17 Dome Lens Contro alii A A A AAA ea te 17 Set Dome Functions ii A Joie pel A A AA VAE el A el ee 18 O eid a oh ee eA Ger erated 18 SAO A Aa AA a aes dee Le eae etl lan dived Aaa 18 Pattern a A ica claude 18 Cruise Cicas a dn vn i els A aes Pod Kn R AA an dak n a E av nk ee 19 CalliMain Men vii A di 19 MatriX Control iii da oda dba 19 Switching th Dome Order cuca ac 19 Call Matrix Main Menu 0 a A AAA OLA DE ea ae PALA ae a 20 Confirm After Program iia A A A A plno 20 V XSDZ 3DM User Manual M vision Change Object Monitor ativan ra A A da ad dob t 20 IEA E MA 20 Keyboard Parameter Settings drer A dis 21 Keyboard ID Setup iaa a A gle ieee ies bida upe tae 21 Keyboard Baud Rate Settings cerrada Ge each ede gs 23 Joyvstick Ad ustmeht e a a dad 24 Display Keyboard
9. Information gt sidra a a 24 A A e A anne 24 Preset Setupe ut e A A A Pt 24 Dome Scan Set p sit ii A lio eed 26 Patter Set p pta lan 28 A E o Koi a ys kav rondel ve bony beda So ooo hol L ooo o 29 Protocol Setup tard ic de hk 30 V o 8 XSDZ 3DM User Manual 6 vision Pelco Matrix Model av achat Azad ok AA da evades he ei Wd hi ie 30 Dome Control Model aieiaiei aa A ap doen ik ee deky or adidas 30 Exit Keyboard Menu s tei eee Wis A ed ee A A Hd ee a ee 30 Append lx oia dd A PLease secs ee Magee ed aa Mere ee 31 RS485 Bus General Knowledge iii ie so h GA ei en ee eh 31 Keyboard Shortcut Instruction uti aie deed Maile dela sendin naval dais deed nape eae ie 34 Keyboard Men Index nicius innne dirina iir bea 37 AMI XSDZ 3DM User Manual M vision 1 Introduction The XSDZ 3DM controller is a universal keyboard and joystick designed to control speed dome cameras for security systems The XSDZ 3DM can control both the camera s movement and the zoom magnification of its lens A functional backlit LCD screen displays the parameters of the current operation the protocol ID the dome ID the monitor ID and the operational state of the joystick The joystick together with the LCD screen provides the user with a more efficient and easier control for their security systems 1 1 Notice Please read the manual carefully and follow all instructions AMI XSDZ 3DM User Manual M vision 1 2 Functions a
10. R remote control Figure 2 1 AMI XSDZ 3DM User Manual d Ivision 2 2 Direct Connection to Dome The keyboard connects to the Dome via the RS485 interface which is the communication port This is illustrated in figure 2 3 1 below DC12V A B RS485 A B Speed Dome Camera Keyboard Figure 2 3 1 11 AMI XSDZ 3DM User Manual d Ivision 2 3 Keyboard Connection through Matrix You can indirectly control the dome when it connects through a matrix as shown in the illustration below Connect the keyboard and dome in a parallel way to the bus of the RS 485 The keyboard can control any dome in the series Using this method the ID of the main keyboard should be 1 and the baud rate should be 9600bps Figure 2 4 1 Keyboard Dome 1 Dome 2 Please Note e With a direct connection the keyboard can control a maximum number of 31 cameras using the RS485 bus e The maximum number of keyboards that can be used in a system is four 4 e The controllers should all be given different IDs as shown in figure 2 4 2 below 12 XSDZ 3DM User Manual vision CoE EE Keyboard 1 Keyboard 2 Io DDD Keyboard 3 Dome 1 Dome 2 Dome 3 Dome 4 TTD OI E US a AU Keyboard 4 Dome 1 Dome 2 Dome 3 Dome 4 Figure 2 4 2 13 Pa s XSDZ 3DM User Manual bvision 3 Keyboard Operation Instruction Figure 3 1 1 MEE Other security systems may have different operational requirements and ma
11. XSDZ 3DM Speed Dome Keyboard 8 Joystick Controller USER MANUAL De XSDZ 3DM User Manual M vision CAUTION Please read this user manual carefully to ensure that you can use the Keyboard and Joystick correctly and safely We cannot guarantee all the content is correct The contents of this manual are subject to change without notice This controller should be operated only from the recommended power source Technical Data Page 9 The voltage of the power must be verified before use Kindly remove the cables from the power source if the controller is not to be used for a long period of time Do not install this controller near heat sources such as radiators heat registers stoves or other devices that produce heat Do not install this controller near water Clean only with a dry cloth Do not block any ventilation openings and ensure the controller is well ventilated This eguipment is for indoor use only Do not expose the device to rain or a moist environment In case any solid or liguid gets inside the keypad please cut off the power supply immediately and get it checked by a gualified technician Refer all servicing to gualified service personnel You should repair no parts without technical aid or approval This manual is suitable for the XSDZ 3DM Speed Dome Keyboard and Joystick controllers V o 8 XSDZ 3DM User Manual 6 vision Contents Introduction isidro as did alabada ltd 7 NOTICE it A A A A
12. and forth until it finally gets to the 16 camera 19 XSDZ 3DM User Manual vision 3 8 2 Call matrix main menu e Shi Set Calls the main menu the menu will display on the object monitor o Press the Shift button and then the Set button o Refer to the matrix section of the manual to know how to use the keyboard in setting the matrix 3 8 3 Confirm after program e Ent o Press the Enter Ent button to confirm once the matrix has been programmed successfully o Refer to the matrix section of the manual for detailed programming 3 8 4 Change object monitor e N Mon o Input the monitor ID number and then press the Mon button The image and the menu of the dome that you controlled with the keyboard will be displayed in the object monitor 20 AMI XSDZ 3DM User Manual M vision 4 Keyboard Menu Control e Press and hold the Menu button for 3 seconds to enter the main menu Figure 4 1 1 1 The entire menu settings will be displayed Now enter the corresponding number or use the Joystick to move up down and select a particular camera e Once you find the specific camera move the joystick to navigate the menu right to enter left to leave Keyboard setup Dome setup Protocol select Exit menu Figure 4 1 1 1 e To save the settings press the Ent button to save the settings and the text lt Success gt will be displayed e To return back to the previous menu press the Prev button 4 1 Keyboard Parameter Setti
13. ccess gt will be displayed and then revert back to the previous menu upon completion Select Item 2 as shown in figure 4 2 4 2 You will need to input the tour preset and in the second item you need to input the speed information range is between 1 27 In the third option you will need to input the time it needs to stop The range is from 1 255 After finishing all the steps press the Ent key This will display lt Success gt on the screen and then revert back to the previous menu 1 Preset Number 2 Speed Figure 4 2 4 2 3 Dwell Press 3 to run the Tour 29 AMI XSDZ 3DM User Manual M vision 4 3 Protocol set up Enter the main menu Figure 4 1 1 1 Press the number 3 button to enter the Protocol Setting menu figure 4 3 1 1 Matrix DVR s 2 Dome Figure 4 3 1 4 3 1 Pelco Matrix model Press the number 1 button to enter the PELCO Matrix menu as shown in the picture 4 3 1 1 Press the Ent key to select the protocol options and then revert back to the previous menu 1 P Matrix Figure 4 3 1 1 2 HC DVR 4 3 2 Dome control model From the Protocol Setting Menu figure 4 3 1 press the number 2 to enter the dome control menu figure 4 3 2 1 Select the appropriate Protocol by choosing options 2 or 3 PELCO P or D and then go back to the previous menu 1 Factory 2 Pelco P 3 Pelco D Figure 4 3 2 1 4 3 3 Exit Keyboard Menu From the main menu figure 4 1 1 1 and press th
14. e number 4 button to exit the menu 30 XSDZ 3DM User Manual vision 5 Appendix 5 1 RS485 Bus General Knowledge According to the RS485 Industrial Standards the RS485 Bus is of half duplex data transmission cables with a characteristic impedance of 120 The maximum load capacity is 32 unit loads including the main controller and the controller equipment Distance of RS485 bus transmission Use the 0 56mm 24 AWG twisted cable as the communication line the farthest distance it can reach is as follows based on the different Baud rates Baud Rate Maximum Distance 2400bps 1800m 4800bps 1200m 9600bps 800m 19200bps 600m To ensure maximum transmitting distance the RS485 Uses high quality cables Installs the dome in an environment with a minimum amount of electromagnetic interference Minimizes the amount of equipment workload on the RS485 Bus 31 Va XSDZ 3DM User Manual M vision Connection and termination resistance The RS485 standards reguire a daisy chain connection between the eguipment There must be termination resistance of 120 Impedance at both ends of the connection Please refer to figures 4 1 1 and 4 1 2 J CJL C 1 2 3 4 32 Figure 4 1 1 2 3 4 32 Figure 4 1 2 MECA Connection D should not exceed 7m 32 AMI XSDZ 3DM User Manual M vision Problems during practical use In some circumstances the user adopts a star c
15. m Out Direct Far High Speed Dome Press Far far focus Control Mode Near High Speed Dome Press Near near focus Close High Speed Dome Press Close reduce Iris Open High Speed Dome Press Open increase Iris Set N Preset High Speed Dome Adjust the image to object position Press Set to input the preset and press Preset to set the preset N Preset High Speed Dome Input preset ID press Preset to call the preset Shi 1 Ent High Speed Dome ON OFF water Wiper 34 XSDZ 3DM User Manual vision Shi 2 Ent High Speed Dome ON OFF auxiliary light Set 1 Scan High Speed Dome Adjust the image to object position press Set to input 1 then press Scan to set Scan left limit Set 2 Scan High Speed Dome Adjust the image to object position press Set to input 2 then press Scan to set scan right limit 1 Scan High Speed Dome Input 1 press Scan to run scan Set N Pattern High Speed Dome Press Set then input pattern number press Pattern to record pattern path Set 0 Pattern High Speed Dome Press Set then input 0 Press Pattern to save pattern N Pattern High Speed Dome Input the pattern path 1 4 Press Pattern to start pattern N Tour Tour High Speed Dome Input the Tour number press Tour or directly press Tour to start the Tour 9 5 Preset High Speed Dome Input
16. nd Characteristics e The keyboard can connect up to maximum of 31 domes in the direct control mode using an RS485 Bus Line e Compatible with a wide range of speed dome operating protocols e Also controls the camera s Iris Focus and Zoom e Set and run presets scans patterns and tours e Control the matrix which then controls the dome indirectly e Equipped with a 3D Joystick e A functional backlit LCD screen displays the parameters of the current operation the protocol ID the dome ID the monitor ID and the operational state of the joystick AMI XSDZ 3DM User Manual M vision 1 3 Technical Data Operating Voltage e Inputvoltage 12V DC e Rating Power 0 5W Communication Characteristics e Communication interface RS485 Bus Line with Infrared emission e Communication frequency 2400 4800 9600 and 19200bps e Communication distance RS485 can reach 1 2km infrared emission reaches 10m Operational Environment e Operating temperature 0 50 C e Relative humidity less than 90 Dimensions e 68x 136 x 105mm L x W x H e Weight 0 845 kg VIO XSDZ 3DM User Manual d Ivision 2 Keyboard Connection 2 1 RS485 Interfaces RS485 can be connected by the 2 port terminal block at the front of the controller An RS485 A B interface allows the controller to connect with the speed dome directly via a DVR or other keyboards i e if the keyboard controls the dome via a matrix The Keyboard Power RS485 I
17. ngs 4 1 1 Keyboard ID set up Enter the main menu as shown in figure 4 1 1 Press the number 1 button to select the keyboard setting as shown in figure 4 1 1 2 detailed below 21 XSDZ 3DM User Manual vision Set KB ID 1 64 Set Baud rate 2400bps Figure 4 1 1 2 Joystick Calibration About keyboard Press the number 1 button to select Set KB ID as shown in figure 4 1 1 3 below 1 Set KB ID 1 64 Figure 4 1 1 3 Press the number 1 to set the keyboard ID as in Figure 4 1 1 4 below 1 Set KB ID 1 64 decidio Input the specified number to select the camera ID within the range 1 64 and then press the Ent to save If successful the text lt Success gt will be displayed at the bottom of the screen If the number you input is outside of the range1 64 it will display Error as shown in figure 4 1 1 6 Figure 4 1 1 6 Error 22 AMI XSDZ 3DM User Manual M vision Press the Prev button or use the LEFT RIGHT arrows for the back and previous menu MEAN The default camera ID is 1 If there is only one keyboard in the system then it must be set to 1 Several keyboards can work together i e maximum of 4 with at least one keyboard ID set to 1 4 1 2 Keyboard Baud Rate Settings Enter the main menu as in Figure 4 1 1 1 Press the number 1 button to enter the keyboard settings Press the number 2 button to enter the Baud Rate settings as in Figure 4 1 2 1
18. onfiguration in practical connection The termination resistors must be connected to both equipment and should be farther away from each other such as equipment1 and 15 refer to figure 4 1 3 As the star configuration does not conform with the reguirements of the RS485 standards problems such as signal reflections and lower anti interference performance arise when the cables used in the connection are too long The reliability of control signals are decreased with the phenomena that the dome does not respond to or just responds at intervals to the controller or follows a continuous operation without stopping Under such circumstances the factory will recommend the use of the RS485 distributor The distributor can change the star configuration connection to the mode of connection stipulated in the RS485 standards The new connection then achieves a reliable data transmission Please refer to figure 4 1 3 1200 1 A 6 Main Controller 32 I 1 1200 15 2 3 Figure 4 1 3 33 XSDZ 3DM User Manual vision 5 2 Keyboard Shortcut Instructions Working Operation F Mode Shortcut Object unction Press Set for 3 seconds Keyboard IR remote ON OFF Press Menu for 3 seconds Keyboard Enter the system setting D ID m N Cam High Speed Dome Te ane prose Sam select object dome Rotate the joystick anti clockwise High Speed Dome Zoom In Rotate the joystick clockwise High Speed Dome Zoo
19. ure 4 2 1 1 From here you can set the following functions Preset Scan Pattern and Tour These functions can also be set up in the camera s menu 24 XSDZ 3DM User Manual vision Set dome preset Set dome scan Figure 4 2 1 1 Set dome pattern Set dome tour Press the number 1 button to enter the dome Preset function settings as in figure 4 2 1 2 below Save preset Show preset Figure 4 2 1 2 Clear preset Press the number 1 button to enter the preset menu you can input the preset number as in figure 4 2 1 3 Preset Number 1 128 Figure 4 2 1 3 Press PREV to go back After entering the preset menu you can use the navigation keys to control the dome directly Input the preset number to save lf successful the text lt Success gt will be displayed Press the Prev button to go back to the previous menu MECANO Under this mode operating the keys and moving the joysticks will not control the domes 25 AMI XSDZ 3DM User Manual M vision Press the number 2 button to view the presets figure 4 2 1 5 Preset Number 1 128 Press PREV to back Figure 4 2 1 5 Input the Preset Number that you would like to view and press the Ent button If successful the text lt Success gt will be displayed and then press the Prev to revert back to the previous menu Press the number 3 enter the Clear Preset option as figure 4 2 1 6 below Preset Number 1 128 Figure
20. y not be compatible AMI XSDZ 3DM User Manual M vision 3 1 Power Mode When the keyboard is turned on it automatically checks the Baud Rate the Protocol of the keyboard the Dome and Monitor ID s and displays all the information on the LCD screen Please Note The joystick should be not be touched whilst the keyboard is initialising 3 2 LCD display screen The LCD screen displays the following as shown in the illustration below It also displays the parameters of the current operation and the operational state of the controller MEAN The LCD backlight switches turns off automatically after 10 seconds of inactivity Cam ID 001 Mon ID 001 Protocol PELCO D Baud Rate 2400bps 15 Va XSDZ 3DM User Manual M vision 3 3 Functions of the Joystick The Joystick controls the both the movement of the dome and navigating the operational setup menu e You can operate the joystick at will in any direction and the Speed Dome will move in that direction detailed below E EU M e Navigating menu items The top arrow is also used for navigating upper menu items Tr The down arrow is used for navigating lower menu items u M The right arrow is used for navigating next menu items E The left arrow is used for navigating previous menu items METAN There is a direct proportion between the speed of the movement of the dome and the pressure applied to the joystick 16 AMI XSDZ 3DM User Manual M vision
Download Pdf Manuals
Related Search