Addendum B2000 User's Manual
Contents
1. Before it is off push lt SET gt appears CAL on the left display Press lt SET gt to entry in the program for the calibration of sensors appears In on the left display and the default value for distance on the right display Input the distance as at 2 2 of the addendum Press lt SET gt diA appears on the left display and the default value of diameter on the right Input the diameter as at 2 1 of the addendum Press lt SET gt C1 appears on the left display Start the wheel unclockwise spin ADVICES Using the standard tooluntil the correct speed of the wheel NOTE During the spin Acc El rEd UCE or Go od appears on the display to indicate that you have to accelerate reduce the speed or that it s ok Also the leds of the display indicate the good speed when all are light on the speed is ok Err 19 appears if the speed is not good before of 4 after the start Then St oP blinks after that a new start is required after stop the wheel The display shows from 5 to 0 when the speed decrease When St oP blink lock the wheel tu rn appears on the display Turn the wheel until 60 Put appears on the display Put 60grs adhesive weight on inside see 6 7 4 on the User s Manual Press lt SET gt C2 appears on the left display NOTE Press lt SET gt when the wheel is lock into the position of 60grs weight is required nothing happens if press lt SET gt in different position See the 3 6 for the second run The di2. FASEP 2000 srl F DOCUMENT SERVICE TECH_DOC WB B2000 12 to 20c_ing wpd Rev 1 March 12 2003 Addendum B2000 User s Manual From 1 20 version to 2 0c version VERSION 2 0c VERSION 2 0b VERSION 2 0a VERSION 2 0 1 Placing the wheel only B201 1 1 Install the support on the shaft Fig 1 Fig 1 1 2 Select the adaptors Fig 2 e 3 Fig 2 Fig 3 1 3 Placing the wheel on the shaft select the adaptors to put outside of the wheel 1 4 Select the correct adaptors to install until the end of the support and lock the wheel Fig 4 Fig 4 FASEP 2000 srl F DOCUMENT SERVICE TECH_ DOC WB B2000 12 to 20c_ing wpd Rev 1 March 12 2003 2 Input of rim dimesnion only B201 2 1 INPUT OF DIAMETER See the 5 4a 1 of the User s Manual 2 2 INPUT OF WIDTH Put the rod on the inside of the rim Fig 5 See the value of the distance on the graduated scal on the rod Fig 6 See the 5 4a 2a of the User s Manual to insert the distance Fig 5 Fig 6 2 3 INPUT OF THE WIDTH Measure the value of the width with the width gauge Fig 7 see on the User s Manual Fig 7 FASEP 2000 srl F DOCUMENT SERVICE TECH_DOC WB B2000 12 to 20c_ing wpd Rev 1 March 12 2003 3 Calibration only B201 3 1 3 2 3 11 3 12 Place a wheel most balance as it possible on the flange see the chpater 1 of the addendum for placing of the wheel Switch on the wheel balancer Sor X XX software version is displayed
3. splay shows from 5 to 0 when the speed decrease When St oP blink lock the wheel ST OP appears on the display Press lt ESC gt to escape from calibration procedure FASEP 2000 srl F DOCUMENT SERVICE TECH_ DOC WB B2000 12 to 20c_ing wpd Rev 1 March 12 2003 4 MEASUREMENT AND CORRECTION OF IMBALANCE only B201 4 1 Place the wheel rim on the shaft paying attention to the position of the pin or bolts according to each case see the chapter 1 of the addendumfor assembling wheel 4 2 Insert details of the wheel see chapter 2 of the addendum 4 3 Start the wheel The wheel has to be run unclockwise ADVICES Using the standard tooluntil the correct speed of the wheel g NOTE During the spin Acc El rEd UCE or Go od appears on the display to indicate that you have to accelerate reduce the speed or that it s ok Also the leds of the display indicate the good speed when all are light on the speed is ok Err 19 appears if the speed is not good before of 4 after the start Then St oP blinks after that a new start is required after stop the wheel 4 4 When St oP blink lock the wheel 4 5 See 6 7 4 of Users Manual to apply the weight
Download Pdf Manuals
Related Search