USER MANUAL
Contents
1. V1 00 06 2007 Multiform Leigh on Sea UK 4 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply AN MULTIFORM The pre programmed soft fade or hard switching patterns can be chosen by means of CH1 whilst CH2 is used as a dimmer channel CH3 allows to set the fade time or pattern speed from slow value 50 to very fast value 255 If channel 4 reaches a DMX value of 50 or above a strobe will be added to the chases The strobe speed can be adjusted from slow value 50 to 23 flashes per second value 255 Note Whether the unit works in static colour mode or pattern mode only depends on the value of channel 3 So make sure the value of channel 3 is lower than 50 to be in static colour mode Otherwise you will be in pattern mode In this mode the potentiometer 1 is disabled Addressing has to be done as follows 001 first device CH 1 4 factory default 005 second device CH 5 8 009 third device CH 9 12 013 fourth device CH 13 16 and so on This setting is stored even if the device is switched off Display on off If you wish the display to be lit only when a change in operation is made the DIP switch 10 should be in the position off Now if any of the buttons is not pressed for more than approximately 25 seconds the display is switched off As soon as one of the buttons is pressed again the display switches on immediately In this case the first touch of the button is ignored in respect to the normal function2. DMX CH3 lt 50 CH3 gt 50 CH1 Red Red Colour Pattern Red Red CH2 Green Green Dimmer Dimmer Green Green CH3 Blue Blue 0 49 Speed Blue Blue CH4 0 0 Strobe Strobe Dimmer Strobe 0 protection Where the mains plug or an appliance coupler is used as a dis connect device the disconnect device shall remain readily operable a Maintenance This unit does not need regular maintenance The internal circuit is protected by a 250V 2A slow blow fuse 5x20mm fuse If this fuse fails this usually indicates an internal fault requiring servicing by a qualified engineer The fuse shall only be replaced by a fuse of same specification and the replacement has to be made by qualified personnel obeying applicable safety rules V1 00 06 2007 Multiform Leigh on Sea UK 14 4 To pull the AC Cord out of the wall outlet or the units AC socket never pull the cable itself but only the AC plug 5 Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the units AC socket before any kind of cleaning on the product Use smooth and dry cloth only for cleaning Check all connection cables before reconnecting the unit 6 Do not expose this unit to any dripping or splashing liquids and do not place objects filled with liquids such as vases on the unit Do not operate this unit near to open water or in high humidity 7 Choose the position of the AC cord according to the lowest risk of damage by foot steps or by squeezing
3. Operate the PS020A DMX controlled 3 Channel power supply in environments with more than 40 degrees environmental temperature or more than 80 humidity Operate the PS020A DMX controlled 3 Channel power supply in any position inclined or reclined more than 45 degrees from being upright heatsink on top Operate the PS020A DMX controlled 3 Channel power supply in any closed environment smaller than 10cbm unless forced air convection is provided V1 00 06 2007 Multiform Leigh on Sea UK 7 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WO MULTIFORM m Operation The PS020A DMxX controlled 3 Channel power supply supplies the necessary power to the passive RGB LED Panel unit plus provides all necessary functional control User interface overview 1 In A Mode Speed Control except A1 Colour Mix Control In C Mode Dim Level Control 2 Display showing the Mode DMX address LOC function etc 3 Indicates presence of a DMX signal 4 Indicates the sound to light mode internal microphone 5 MODE selection button 6 UP button 7 DOWN button 8 Internal microphone 9 Switches on the termination for the last unit in the DMX chain 10 Switching the display on or off with delay 11 Maintenance not in use 12 Power Input 85 240V AC 13 DMX Output connector 14 DMX lInput connector V1 00 06 2007 Multiform Leigh on Sea UK 8 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply AN MULTIFORM Upon
4. it Take especially care of the AC cord outlet on the unit as well as the AC plug and wall outlet at the other end of the cable 8 Do not open the unit for service purpose as there are no user serviceable parts inside Warranty will be void in any case of unauthorized service by the user or other not authorized persons V1 00 06 2007 Multiform Leigh on Sea UK 3 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WW MULTIF ORM Protection from fire AAN 1 Take care of not placing the unit near sources of heat e g powerful amplifiers fog machines 2 Take always care of sufficient air convection in the unit s environment to avoid overheating especially when mounting in a closed environment Make sure air convection slots are not blocked Do not operate this unit in environmental temperatures exceeding 40 degrees Celsius 3 Check the total maximum power of your AC wall outlet if you connect several units to one wall outlet and avoid any overloading Protection from injury and damage 1 Never use any accessories or modifications not authorized by the manufacturer of this unit 2 Choose a location for operation where the unit is protected from vibration and where a fixed mounting position is provided In case of overhead mounting follow appropriate rigging rules and your country s regulations for rigging safety See appendixes if any 3 Before plugging the AC cord in the wall outlet check whether the AC main
5. lost but potential strobe settings will be automatically cleared DMX channel assignment overview User Manual PS020A Dmx controlled 3 CHANNEL Power Supply AN MULTIFORM General advice AN 1 Read this manual completely before using the product 2 Keep this manual in your records for future reference 3 Follow all instruction printed in this manual otherwise warranty may be void 4 Follow all printed security advice on the product itself The lighting flash with arrowhead within an equilateral triangle makes you aware of non insulated AC mains voltage inside the unit The exclamation mark within an equilateral triangle makes you aware of important operating and maintenance instructions in the literature attached to this product 5 Take care of enough distance between this product and sources of hum and noise like electric motors and transformers 6 Carry this product with greatest care Punches big forces and heavy vibration may damage this product mechanically 7 The manufacturer takes no responsibility for injury or damage caused by not following the safety precautions and instructions printed in this manual Protection from electric shock 1 Do not connect the AC power plug to the unit before assembly has been completed 2 Only connect this unit to a mains socket outlet with protective earth connection ground fault earth fault protection and overload Mode gt A Cc P P d SLA
6. of that button Key lock Pressing the MODE button 5 for longer than 3 seconds locks all the buttons 5 7 and the potentiometer 1 The display shows LOC in alteration to the mode changing every 2 seconds Pressing the MODE button again for more than 3 seconds unlocks the button and potentiometer functions Please note If the display is in OFF mode it will take approximately 25 seconds before the display switches off It will be switched on again if any key is touched and will switch off again after 25 seconds if the keys are not unlocked by the procedure mentioned above Termination To avoid interference the last unit of a DMX chain should be terminated Therefore the DIP switch 9 of the last unit in the DMX chain must be switched ON V1 00 06 2007 Multiform Leigh on Sea UK 13 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WW MULTIF ORM P DMX Preset Mode If you want to run the pre programmed patterns and scenes by an external DMX controller you can use the DMX Preset Mode Press the MODE button 5 until the display shows P indicating operation in P DMX Preset mode Set the DMX starting address by simply using the UP DOWN buttons 6 7 The chosen DMX address comes effective approximately 3 seconds later and will show up on the display 2 in alternation to the P The unit receives DMX values on a packet of four channels and mirrors the received data on the DMX output 13
7. COnnectionS cece enari teeta eaten raaa 3 pin XLR Male Female Modulation Type 0 ceceeeeeeeeeeeeeeeeeeees Advanced Bit Angle Modulation ABAM COmMtrOl PHOTO COM A E DMX 512 1990 DIMENSIONS 23s teea ces saaiehistacesGhiys R a a codon iei ones W 135 x H 109 x D 38 mm Weightman aa a aa ins E E A E cabeza E E APAE EA 0 6 kg m Standards This product complies with the following standards EU SafE to oinen esadi cenre sac sareei ea e aeee anae aeea EE Er OSEANE REEE EN 60065 2001 A1 EU EMG oirrese nureen iie ican E AAEREN EEEa EN61204 3 2001 US safety pending eeri siaina aa cas naa a ai a UL60065 US EMG aciari aaea a a aaa aaa EE ana FCC Part 15 This product meets both the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC V1 00 06 2007 Multiform Leigh on Sea UK 15 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WW MULTIF ORM Maintenance Boot loader The Maintenance boot loader function enables the unit to receive firmware updates via the DMX connectors For further information refer to the website www multiform lighting com and check Download Switch on condition The unit always returns to the last mode before it was switched off In DMX Slave SLA or DMX Mode d or DMX Preset Mode P all DMX values are cleared LED s off if power is switched off DMX signal drop condition The device will retain the status that it was in before the DMX signal got
8. If a DMX signal is present the DMX LED 3 will turn on The four channels control the unit as follows If DMX value of channel 3 is lower than 50 the unit works with static colours DMX Channel Value Range Function CH1 000 255 Colour choice from presets see C mode CH2 000 255 Dimmer CH3 000 049 Static colour mode active CH4 000 049 Strobe off 050 255 Strobe 050 slow 255 max speed 23 Hz Colour presets can be activated by means of CH1 whilst the chosen colour can be dimmed by weighting the colour balance with CH2 If the value of CH4 is above 50 the unit is set to strobe mode The strobe speed for any fixed colour chosen on the first channel can be adjusted from zero value lt 50 to 23 flashes per second value 255 If DMX value of channel 3 is equal or higher than 50 the unit works in pattern mode CH1 Pattern CH1 Pattern 000 015 Soft fade red green 136 150 Hard switch green blue 016 030 Soft fade green blue 151 165 Hard switch red blue 031 045 Soft fade green blue 166 180 Hard switch red yellow 046 060 Soft fade red yellow 181 195 Hard switch candy lime 061 075 Soft fade candy lime 196 210 Hard switch pink blue 076 090 Soft fade pink blue 211 225 Hard switch turquoise pink 091 105 Soft fade turquoise pink 226 240 Hard switch red green blue 106 120 Soft fade red green blue 241 255 Hard switch red yellow green 121 135 Hard switch red gr
9. User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WW MULTIF ORM m APPENDIXES A Safety rules for overhead rigging applicable if the PSO20A DMX controlled 3 Channel power supply is mounted to any of the Multiform LS series passive RGB LED panels Risk of injury Overhead mounting requires extensive experience AN including among others calculating working load limits good knowledge of the installation material being used and periodic safety inspection of all installation material and the unit If you lack such qualifications do not attempt the installation yourself Improper installation can result in body injury Be sure to complete all rigging and installation procedures before applying power to the unit e The unit should be installed out of reach of people and outside areas where persons may walk by or be seated e Make sure that the installation area can hold a minimum point load of 10 times the device s weight e In fixed installations fix the unit with self locking screws nuts to the mounting point e When mounting the unit to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke e Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment f
10. ails e Never stand directly below the device when mounting removing or servicing the fixture Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing e The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be inspected every year by a skilled person to be sure that safety is still granted V1 00 06 2007 Multiform Leigh on Sea UK 16 USER MANUAL PS020A DMxX controlled 3 Channel power supply AAN MULTIFORM Updated versions of this document may be available at WWW MULTIFORM LIGHTING COM RevA 06 2007 Order code 12 010 0233 80100 1 01 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WW MULTIF ORM m Introduction Dear customer congratulations on the purchase of a Multiform branded item and the trust having been put in us with this decision Multiform is one of the leading global manufacturers of professional lighting equipment and has decades of experience in design production and quality assurance To meet your requirements this unit has been designed and built to the highest standards so that we can assure you that you have made a good and satisfying investment To take full advantage of all possibilities and for your own safety and the safety of your environment please read these operating instructions carefully before yo
11. b 1 determines the dimming level In C mode the unit does not receive any values from the DMX input but generates related DMX values on the output according to the selected pattern so that other similar units from the Multiform LS series of LED devices can show the same colour if they are connected by DMX signal cables and set to Slave Mode SLA NOTE The C Mode is automatically disabled and can not be chosen when an external DMX signal is received DMX indicator LED 3 is lit If you leave mode C for any reason and come back later into mode C the unit will recall the last chosen colour even if the unit was switched off in between Available colour presets co all off C10 Frog C1 Red C11 Lavender C2 Green C12 Candy C3 Blue C13 Peach C4 Yellow C14 Aqua C5 Pink C15 Leaf C6 Turquoise C16 Purple C7 Lime C17 Barbie C8 Orange C18 Breeze c9 Marine C19 White V1 00 06 2007 Multiform Leigh on Sea UK 10 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply AN MULTIFORM m Getting started choosing a location Risk of fire The PS020A DMX controlled 3 Channel power supply has been designed to work in dry indoor environments at environmental temperatures up to 40 degrees Celsius For proper operation the PS020A DMX controlled 3 Channel power supply must be operated with its heatsink side up and unobstructed air convection to the heatsink
12. ected by DMX signal cables and set to Slave Mode SLA If you leave mode A for any reason and come back later into mode A the unit will recall the last chosen pattern even if the unit was switched off in between Pattern list Description Function of Knob 1 AO All off none A1 Static scene Colour A2 Soft fade red green Speed A3 Soft fade green blue Speed A4 Soft fade red blue Speed A5 Soft fade red yellow Speed A6 Soft fade candy lime Speed A7 Soft fade pink blue Speed A8 Soft fade turquoise pink Speed A9 Soft fade red green blue RGB Speed A10 Hard switch red green Sound to light Speed A11 Hard switch green blue Sound to light Speed A12_ Hard switch red blue Sound to light Speed A13 Hard switch red yellow Sound to light Speed A14 Hard switch candy lime Sound to light Speed A15 Hard switch pink blue Sound to light Speed V1 00 06 2007 Multiform Leigh on Sea UK 9
13. een turquoise blue pink DMX Value range Function CH2 000 255 Dimmer CH3 050 255 Chase speed CH4 000 049 Strobe off 050 255 Strobe 050 slow 255 max speed 23 Hz V1 00 06 2007 Multiform Leigh on Sea UK 12 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply AN MULTIFORM Functional advice This unit is immune to the presence of electromagnetic disturbances both conducted and radiated up to a certain level Under peak conditions the unit is classified to show a class C performance criteria and may encounter temporary degradation or loss of function which may need manual help to recover In such case disconnect the AC power from the unit and reconnect it again to recover a Environmental advice This unit is build to conform to the ROHS standards and the WEEE directive 2002 96 EC of the European Parliament and of the Council of the European Union Under these regulations the product shall not be discarded into regular garbage at the end of its life but shall be returned to authorized recycling stations xg m Unpacking Please check that the box contains the following items Main parts 1 pcs PSO20A main unit 1 pcs mains cable 1 pcs operation manual Accessory parts 1 pcs Mounting cover 2 pcs Mounting screw 1 pcs connection cable to panel If any part is missing please contact your dealer immediately for replacement Note Your dealer may have chosen to pre assemble this product
14. hown if no external DMX signal is supplied to the unit Connect external DMX connections if any 2 Fix the PSO20A DMX controlled 3 Channel power supply on the back of a Multiform LS series passive RGB LED panel see illustration below showing LS1310 Fix the screws to the LED panel into the provided mounting points first 1 leaving some clearance to slide on the PSO20A DMX controlled 3 Channel power supply Then slide the PS020A DMxX controlled 3 Channel power supply on the screws using the slots on the rear side 2 Remove the cover of the PSO20A DMx controlled 3 Channel power supply and fix the screws through the holes provided in the units PCB Re fit the cover of the PSO20A DMX controlled 3 Channel power supply 3 Plug the provided connection cable into the PS020A DMx controlled 3 Channel power supply on one side and the RGB LED panel on the other side until the locking mechanism of the connector is secured Get the black plastic cap fixed at the top end to cover the cable and to fix the power supply itself from sliding off Use the two black screws 4 Plug in the mains cable to the unit and verify the display shows A1 NOTE A1 is only shown if no external DMX signal is supplied to the unit Connect external DMX connections if any V1 00 06 2007 Multiform Leigh on Sea UK 6 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WA MULTIFORM SLA DMX Slave Mode Press the MODE button 5 until the display
15. intensity CH3 000 255 Blue intensity CH4 000 127 Master dimmer 128 227 Strobe 128 slow 227 max speed 23 Hz 228 255 Master dimmer full on Strobe off Addressing has to be done as follows 001 first device CH 1 4 factory default 005 second device CH 5 8 009 third device CH 9 12 013 fourth device CH 13 16 and so on This setting is stored even if the device is switched off V1 00 06 2007 Multiform Leigh on Sea UK 11 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WA MULTIF ORM A16 Hard switch turquoise pink Sound to light Speed A17 Hard switch red green blue Sound to light Speed A18 Hard switch red yellow green turquoise blue pink Sound to light Speed A19 Random speed red yellow Fire None A20 Random speed green blue Ocean None A21 Random speed red blue None A22 Random speed red green blue RGB None A23_ White strobe Sound to light Speed A24 Red strobe Sound to light Speed A25 Green strobe Sound to light Speed A26 Blue strobe Sound to light Speed A27 Strobe chase red green blue Sound to light Speed C Colour Mode Press the MODE button 5 until the first digit on the display shows C indicating operation in C COLOUR mode Then choose by using the UP DOWN buttons 6 7 one of the 19 preset colours as shown in the list below Changing the setting becomes effective directly Kno
16. s voltage and frequency is the same as this product is specified for Whenever your AC plug should not match the wall outlet contact you dealer immediately 4 If fluids have spilled into the unit or small parts have intruded the unit immediately switch off the unit and hand it over to the authorized service for a security check 5 Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the unit s AC socket during a thunder storm in order to avoid any damage on the unit due to AC voltage peaks 6 In cause of not correct function of this unit or damaged AC cord or other damaged parts pull immediately the AC plug out of the wall outlet and hand the unit over to the authorized service for a security check 7 To meet all aspects of functionality and security during mainte nance work to be preformed on this unit all parts should be replaced by genuine spare parts Consequently take care of your dealer or maintenance company to be authorized by the manufacturer m Health advice This unit produces and absorbs electromagnetic radiation The strength of radiation and the sensitivity for disturbing interference matches the CE and FCC requirements A corresponding sign is printed on the backside of the unit Any change or modification may affect the behavior of the unit concerning electromagnetic radiation with the CE requirements eventually not to be met any more The manufacturer takes no responsibility in this case
17. shows SLA indicating operation in SLA SLAVE mode In this mode the unit is set to DMX channel 001 in order to receive the signals from a master unit of the Multiform LS series being in mode A or C The unit interprets CH1 as red intensity CH2 as green intensity and CH3 as blue intensity CH4 is not in use and the potentiometer 1 is disabled This mode can also be used for remotely controlling the unit if no specific DMX address is needed and channels 001 003 can serve as a default To indicate that the unit is controlled by an external DMX signal the DMX LED 3 is lit d Mode DMX Mode Press the MODE button 5 until the display shows d indicating operation in q DMX mode Shortly after that the display shows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons 6 7 The chosen DMX address comes effective approximately 3 seconds later and will show up on the display 2 in alternation to the d This allows control of the unit by any external DMX signal sending on the chosen channel In this mode the potentiometer 1 is disabled The unit receives DMX values on a packet of four channels and mirrors the received data on the DMX output 13 If a DMX signal is present the DMX LED 3 will turn on The four channels control the unit as follows DMX channel Value Range Function CH1 000 255 Red intensity CH2 000 255 Green
18. the user s choice the unit can work stand alone or may be controlled by external DMxX controllers Available modes A Auto Mode Press the MODE button 5 until the first digit on the display shows A indicating operation in A AUTO mode Then choose your desired pattern by using the UP DOWN buttons 6 7 see list below Changing the setting becomes effective 1 second after the new setting is made to allow stepping through presets without previewing all intermediate presets NOTE The A Mode is automatically disabled and can not be chosen when an external DMX signal is received DMX indicator LED 3 is lit Whilst being in pattern A 1 static scene turning knob 1 determines the colour whereas being in one of the other 26 patterns knob 1 controls the speed or selects the sound to light function refer to below pattern list The sound to light function can be activated by setting the knob 1 inside the first 10 degrees of its travel from left detent and it works from a built in microphone 8 which picks up the environmental sound Its activity is shown by the flashing of the right dot 4 in the display The level for all patterns is maximum In A mode the unit does not receive any values from the DMX input but generates related DMX values on the output according to the selected pattern so that other similar units from the Multiform LS series of LED devices can show the same pattern if they are conn
19. u start using the unit m Product description The PS020A DMx controlled 3 Channel power supply is a versatile unit that integrates power supply and control functions for the Multiform LS series of passive RGB LED panels such as The Multispot LS1310 passive RGB LED panel The Multiwash LS1130 passive RGB LED panel The Multiflood LS3042 passive RGB LED panel For extended user advice please refer to the respective panel s user manual Security advice before use Warning Read this section carefully before installing powering AN operating cleaning or servicing this product The following symbols are used to identify important safety information in this manual DANGER WARNING WARNING WARNING Safety hazard Risk Hazardous voltage Fire hazard Read manual before of injury or death Risk of severe or installation and fatal electric shock operation V1 00 06 2007 Multiform Leigh on Sea UK 2 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply AN MULTIFORM m Technical data PS020A DMX controlled 3 Channel power supply Mains INpUteseisccecs iediae aie ceneeaeviad ig oh ke Pde EE dian ade ede dues 85 240V AC 50 60Hz WY PC cneasa maven cide aa ondetan EEEa EAEE switch mode power supply Power CoOnSUMptiOMsicccctsacistcceatiaciensddeanedaancwste one sne in eaa max 48W FUSE dace dteentt erenactali A T 250V 2A T slow blow 5x20mm glass Sound control internal microphone with Automatic Gain Control AGC DMX
20. with any suitable of Multiform s LS series passive RGB LED panels for you In this case the above accessory parts have already been used during assembly m Getting started connecting assembly In case your dealer did not pre connect assemble the unit for you with any of Multiform s LS series passive RGB LED panels you need to connect assemble it before use Risk of electric shock Do not connect the mains cable before the following steps are accomplished For assembly there are two basic choices V1 00 06 2007 Multiform Leigh on Sea UK 5 User Manual PS020A Dmx controlled 3 CHANNEL Power Supply WW MULTIF ORM 1 Fix the PSO20A DMX controlled 3 Channel power supply on a wall by using two screws at the correct distance which do not protrude more than 4mm from the wall surface Fix the screws on the wall first then slide the PSO20A DMX controlled 3 Channel power supply on the screws using the slots on the rear side Remove the cover of the PS020A DMX controlled 3 Channel power supply and fix the wall screws through the holes provided in the units PCB Re fit the cover of the PSO20A DMX controlled 3 Channel power supply Plug the optional extended connection cable into the PS020A DMX controlled 3 Channel power supply on one side and the passive RGB LED panel on the other side until the locking mechanism of the connector is secured Plug in the mains cable to the unit and verify the display shows A1 NOTE A1 is only s
Download Pdf Manuals
Related Search