Brukerveiledning 2 User manual 9 Instrukcja obsługi 15
Contents
1. 13 Some advice in case of combustion problems Error Explanation Solution The chimney is blocked l l l Contact a chimney sweeper dealer for more information clean No draught The flue is sooty or there is accumulated soot on the the flue smoke baffle and burn chamber smoke baffle The smoke baffle is wrongly positioned Verify the assembly of the smoke baffle see assembly instructions Downdraught in the room caused by no draught thatthe Light the fire with an open window If this helps more bigger vents house is too air tight must be installed in the room R OGC d BER NA Ea ene Turn off regulate extractor and or other ventilation If this helps central ventilation system that pulls too much air out of Fe more vents must be installed The flues from two fireplaces stoves are connected to One flue must be repositioned The height difference of the two flue the same chimney at the same height pipes must be of at least 30 cm FR Ar The flue must be moved so that there is an inclination of at least The flue is in a declining position from the smoke dome p 10 from smoke dome to chimney Possibly install a smoke suction to the chimney EE device The flue must be reconnected so that it does not enter into the The flue is too far into the chimney chimney but ends 5 mm before the chimney inner wall Possibly The stove install a smoke suction device release smoke when Soot hatch the basement or2. Storing of wood In order to ensure that the wood is dry the tree should be cut in winter and stored during the summer covered and in a location with adequate ventilation The wood pile must never be covered by a tarpaulin lying against the ground as the tarpaulin will then act as a sealed lid that will prevent the wood from drying Always keep a small amount of wood indoors for a few days before use so that moisture in the surface of the wood can evaporate Usage Not enough air to the combustion may cause the glass to soot Hence supply the fire with air just after the wood is added so that the flames and gases in the combustion chamber are properly burnt Open the air vent and have the door slightly ajar in order for the flames to establish properly on the wood Note that the air supply for the combustion also can be too large and cause an uncontrollable fire that very quickly heats up the whole combustion chamber to an extremely high temperature when using with a closed or nearly closed door For this reason you should never fill the combustion chamber completely with wood It is recommended to keep an even fire with a small amount of wood Too many logs put on hot ember may result in combustion air starvation and the gases will be released unburnt For this reason it is important to increase the air supply just after adding logs Choice of fuel All types of wood such as birch beech oak elm ash and fruit trees can
3. attic that is open and thus Soot hatches must always be closed Hatches that are not tight or lighting the creating a false draught are defected must be changed fire and during combustion Damper top draught vents or doors on fireplaces that are not in use are open and create a false draught An open hole in the chimney after that a fireplace has been removed thus creating a false draught Defect masonry in the chimney e g it is not airtight around the flue pipe entry and or broken partition inside the chimney creating a false draught The cross section in the chimney is too large which results in no or very low draught Close damper doors and top draught vents on fireplaces that are not in use Holes must be completely sealed off with masonry Seal and plaster all cracks and sites that are not tight The chimney must be refitted possibly install a smoke suction device The cross section in the chimney is too small and the chimney cannot carry out all the smoke Change to a smaller fireplace or build new chimney with a larger cross section Possibly install a smoke suction device The chimney is too low and hence a poor draught Increase the height of the chimney and or install a chimney cap smoke suction device The stove releases smoke inside when it is windy outside The stove does not heat sufficiently Too much draught The chimney is too low in relationship to the surro
4. be used as fuel in the insert Wood species have different degrees of density the more dense the wood is the higher the energy value Beech oak and birch has the highest density Attention We do not recommend using fuel 12 briquettes compact wood in our products Use of such fuel may cause the product to overheat and exceed the temperatures determined safe Burning briquettes compact wood is done so at your own risk and only small amounts max 1 3 of normal load should be used for each load Warning NEVER use impregnated wood painted wood plywood chipboard rubbish milk cartons printed material or similar If any of these items are used as fuel the warranty is invalid Common to these materials is that during combustion they can form hydrochloric acid and heavy metals that are harmful to the environment yourself and the insert Hydrochloric acid can also corrode the steel in the chimney or masonry in a masonry chimney Also avoid burning with bark sawdust or other extremely fine wood apart from when lighting a fire This form of fuel can easily cause a flashover that can lead to temperatures that are too high Warning Make sure the insert is not overheated it can cause irreparable damage to the product Such damage is not covered by the warranty Source H ndbok effektiv og milj vennlig vedfyring by Edvard Karlsvik SINTEF Energy Research AS and Heikki Oravainen VTT http www eufirewood info
5. case it would be mixed with ordinary glass it would damage the raw material and could in worst case end the recycling of glass It is an important contribution to the environment to ensure that ceramic glass does not end up with the recycling of ordinary glass Packaging recycle The packaging accompanying the product should be recycled according to national regulations 7 Warranty For detailed description of the warranty conditions see the enclosed warranty card or visit our website www nordpeis com 8 Advice on lighting a fire The best way to light a fire is with the use of lightening briquettes and dry kindling wood Newspapers cause a lot of ash and the ink is damaging for the environment Advertising flyers magazines milk cartons and similar are not suitable for lighting a fire Good air supply is important at ignition When the flue is hot the draught increases and door can be closed Warning NEVER use a lighting fuel such as petrol karosine alcohol or similar for lighting a fire This could cause injury to you as well as damaging the product Use clean and dry wood with a maximum moisture content of 20 The wood should be dried fora minimum of 6 months after it is cut Humid wood requires a lot of air for the combustion as extra energy heat is required for drying the humid wood and the heat effect is therefore minimal This in addition creates soot in the chimney with the risk of creosote and chimney fire
6. m h Fuel charge 1 8kg Refueling interval 52min Opening of the air 15 vent control Operation Intermittent Intermittent combustion refers to normal use of a fireplace i e new wood is inserted when the previous load has burned down to ember 3 Distance to combustible material Ensure that the safety distances are respected FIG 1 When connecting a steel chimney to the top outlet use the security distances required from the manufacturer 4 Assembly The following tools are necessary e 4mm Allen key e 10mm Wrench e 13 mm Wrench Orion is delivered with separate flue outlet collar Follow the correct instructions below depending on which outlet is used top lateral or rear Lateral outlet FIG 2A Unscrew sealing lid on the lateral outlet FIG 2B Bend out the fastening bracket belonging to the sealing lid FIG 2C Fasten the flue outlet collar on to the lateral outlet FIG 2D Fasten the sealing lid on the rear outlet We recommend to use stove cement to ensure that it is completely sealed off Top outlet FIG 3A Unscrew sealing lid on the top FIG 3B Fasten the flue outlet collar FIG 3C Fasten the sealing lid on the rear outlet We recommend to use stove cement to ensure that it is completely sealed off Rear outlet FIG 4 Fasten the flue outlet collar Connection of the flue Please be aware when connecting the 125 mm flue to the smoke dome that the flue is placed inside the flue out
7. dry pieces of kindling wood ignite and ensure that the flames have established before closing the door Open the air vent control FIG 5 before you close the door Additional ignition air is obtained by leaving the door slightly open When the flames are stable and the chimney is warm the air supply is regulated with this air vent control When there is a glowing layer of ash new wood logs can be inserted Pull the hot ember to the front of the combustion chamber when inserting new logs so that the wood is ignited from the front Keep the door slightly open each time new logs are inserted so that the flames get established The fire should burn with bright and lively flames Using the stove with low combustion effect and firing around the clock increase pollution as well as the risk for a fire in the chimney Never allow the stove or flue to become glowing red Turn off the air vent control should this happen Regulation of the air vent control takes some experience but after a little while a natural rhythm for the fire will be found IMPORTANT Always remember to open the air vent control preferably also the door before new wood logs are inserted into a hot burn chamber Let the flames get a good grip on the wood before the air control setting is reduced When the draught in the chimney is low and the vent is closed the gas from the firewood can be ignited with a bang This can cause damages to the product as well as the immedia
8. hen touched Avoid touching any cast iron parts with dust on your fingers Any visible dust on cast iron can be brushed off with the a dry rag Door and glass Should there be any soot on the glass it may be necessary to clean it Use dedicated glass cleaner 11 as other detergents may damage the glass NB Be careful even dedicated glass cleaner can damage the varnish on the door frame A good advice for cleaning the glass is to use a damp cloth or kitchen roll paper and apply some ash from the burn chamber Rub the ash on the glass and finish off with a piece of clean and damp kitchen roll paper NB Only clean when the glass is cold Check regularly that the transition between the glass and the door is completely tight Possibly tighten the screws that hold the glass in place but not too hard as this can cause the glass to crack Periodically it may be necessary to change the gaskets on the door to ensure that the burn chamber is air tight and working optimally These gaskets can be bought as a set usually including ceramic glue CERAMIC GLASS CANNOT BE RECYCLED Ceramic glass should be disposed of as resid ual waste together with pottery and porcelain Recycling of the ceramic glass Ceramic glass cannot be recycled Old glass breakage or otherwise unusable ceramic glass must be discarded as residual waste Ceramic glass has a higher melting temperature and can therefore not be recycled together with glass In
9. insulation requirements if flue passes through a flammable wall Chimney Draft Compared with older models the clean burning stoves of today put significantly higher demands on the chimney Even the best stove will not work properly if the chimney does not have the right dimensions or is not in good working order The draught is mainly controlled by gas temperature outside temperature air supply as well as the height and inner diameter of the chimney The diameter of the chimney should never be less than that of the flue chimney collar At nominal effect there should be a negative pressure of 12 to 25 Pascal The draught increases when e The chimney becomes warmer than the outside air e The active length of the chimney over the hearth increases e Good air supply to the combustion It can be difficult to obtain the right draught conditions in case the chimney is too large relative to the stove as the chimney does not heat up well enough In such cases you may want to contact professional for evaluation of possible measures Draught that is too strong can be controlled with a damper If necessary contact a chimney sweeper Dimensional drawing The illustration indicates the approximate center height of the hole for the flue Distortions in floors and walls may influence the height Place the stove for accurate position and height of the flue chimney connection We accept no liability for typographical errors and changes For y
10. let collar Use stove cement in the joints For the flue connection to the chimney follow the recommendations from the chimney manufacturer Operating control When the stove is in position check that all functions are easy to manoeuvre and appear satisfactory Behind one of the front legs there is a hook for the cool handle FIG 7 Air vent control FIG 5 Left Right Open Closed 10 Door FIG 6 Handle to the right Handle to the left Open Closed 5 Lighting the fire for the first time When the stove is assembled and all instructions have been observed a fire can be lit Be careful with touching the stove the first few times it is used as it may damage the varnish Take care when inserting logs into the burn chamber in order not to damage the Thermotte plates Please note that during the first few firings the insulations panels within the firebox will release moisture contained within them from production This will slow down the burn rate slightly and could cause markings on the glass These are easily removed with glass cleaner once the glass has gone cold Possibly leave the door slightly open the first 2 3 times that the stove is used It is advisable to ventilate the room well when making the fire for the first time as the varnish on the stove will release some smoke or smell Both the smoke and smell will disappear and are not hazardous Lighting a fire Insert small
11. our own safety comply with the assembly instructions All safety distances are minimum distances Installation of the stove must comply with the current rules and regulations of the country where the product is installed Nordpeis AS is not responsible for wrongly assembled stoves Subject to errors and changes For the latest updated version go to www nordpeis com 2 Technical information The stoves from Nordpeis all have secondary combustion and are clean burning The combustion takes place in two phases first the wood burns and then the gases from the fumes are lit by the hot air This ensures that these new stoves have minimal emissions of soot particles and un burnt gases such as CO and are thus better for the environment Clean burning stoves require a small amount of wood in order to obtain a good heat output Use exclusively clean and dry wood We recommend seasoned hardwood with a maximum moisture content of 20 Material Cast iron Surface treatment Heat resistant varnish door doorframe Fuel Wood logs 30 cm Operating range 6 8 kW Efficiency 13 CO 13 Oz 0 157 Draught system Air vent control Secondary combustion clean burning 15 90 m Combustion system Heating area Flue outlet Top lateral and rear Outer 125 mm Flue Alternative versions exsists due to National requirements Weight 72 kg Flue gas temperature 183 C Air supply 21 requirements
12. slightly opened until the flames have a good take on the wood Follow the guidelines in this user guide for correct combustion White glass Using wrong material for combustion such as painted Ensure to use only dry and clean wood or impregnated wood plastic laminate plywood etc Smoke is A levelling out of pressure occurs in the burn chamber Open the air vent control for about 1 min before opening the door released when avoid opening the door too quickly the door is The door is opened when there is a fire in the burn opened Open the door carefully and or only when there is hot ember The combustion temperature is too low Increase the air supply White smoke Black or grey black smoke 14 The wood is humid and contains water damp Insufficient combustion Ensure to use only dry and clean wood Increase the air supply gt 600 _ gt 600 100 600 gt 600 00 2222222222247 gt 1460 Sidemontering Lateral outlet Wylot boczny Toppmontering Top outlet G rny wylot 26 N Nordpeis Nordpeis AS Gjellebekkstubben 11 N 3420 LIERSKOGEN Norway www nordpeis no
13. te environment 6 Maintenance Cleaning and inspection The stove should be inspected thoroughly and cleaned at least once per season possibly in combination with the sweeping of the chimney and chimney pipes Ensure that all joints are tight and that the gaskets are rightly positioned Exchange any gaskets that are worn or deformed Remember that the stove must always be cold when inspected Ashes The ashes should be removed at regular intervals Be aware that the ashes can contain hot ember even several days after the fire is finished Use a container of non combustible material to remove the ashes It is recommended to leave a layer of ashes in the bottom as this further insulates the burn chamber Take care with the Thermotte plates when the ashes are removed particularly when using an ash shovel so as not to damage them Thermotte plates The insulating plates in the burn chamber FIG 8 contribute to a high combustion temperature which leads to cleaner combustion of the wood and a higher rate of efficiency Any fissures in the plates will not reduce their insulation efficiency If new plates are needed contact your dealer Please note Wood logs that are too long can cause strain and crack the plates due to the tension created between the side plates A Right side plate B Left side plate C Rear bottom plate D Forward bottom plate Please note that the Thermotte plates may release coloured dust w
14. unding terrain buildings trees etc Turbulence around the chimney due to the roof being too flat The fireplace combustion receives too much oxygen due to a leakage under the lower border of the stove or too strong chimney draught Difficult to regulate the combustion and the wood burn up too quickly The smoke buffer is wrongly positioned In case of using oven dried wood this requires less air supply than when using normal wood Increase the height of the chimney and or install a chimney cap smoke suction device Increase the height of the chimney and or install a chimney cap smoke suction device Any possible leakage must be sealed off A draught regulator or possibly a damper can reduce the chimney draught NB A leakage of only 5 cm2 is enough for 30 of the heated air to disappear Verify the positioning of the smoke buffer see assembly instructions Turn down the air supply The gaskets around the door are worn and totally flat Replace the gaskets contact your dealer The chimney is too large Contact chimneysweeper or other professional for more details The glass is sooty The wood is too wet The air vent control is closed too tightly Bad combustion the temperature is too low Only use dry wood with a humidity of maximum 20 Open the air vent control to add air to the combustion When new wood logs are inserted all vent controls should be completely opened or the door
15. w Nordpels Orion Brukerveiledning 2 User manual 9 Instrukcja obs ugi 15 Produkt nr SN 00000 000 Sintef nr 045 047 Sist oppdatert 01 01 2013 INDEX 1 Prior to assembling the stove 9 Chimney draught 9 Dimensional drawing 9 2 Technical information 10 3 Distance to combustible material 10 4 Assembly 10 Connection of the flue 10 Operating control 10 5 Lighting the fire for the first time 11 6 Maintenance 11 Cleaning and inspection 11 Ashes 11 Thermotte 11 Door and glass 11 7 Warranty 12 8 Advice on lighting a fire 12 Some advice in case of combustion problems 14 1 Before Installing a New Stove All our products are tested according to the latest European requirements and also to the Norwegian standard NS 3058 and NS 3059 which include particle tests However several European countries have local regulations for installation of fireplaces which change regularly It is the responsibility of the client that these regulations are complied with in the country region where the fireplace is installed Nordpeis AS is not responsible for incorrect installation Important to check please note that this list is not exhaustive e distance from firebox to combustible flammable materials e insulation materials requirements between fireplace surround and back wall e size of floor plates in front of fireplace if required e connection between firebox and chimney e
Download Pdf Manuals
Related Search