SERVICE MANUAL
Contents
1. mica SERVICE MANUAL Freestanding cooker 500 and 600 Range 2013 Gas electric Ceramic electric Electric Manual developed by R Stotowski E Banach R Bedonski Address your questions to serwis dokumentacja amica com p Contents O 0 YO 01 0nN Product identification Door assembly Oven chamber seal Knob assembly gas cooker Oven shelves Hob gas cooker Thermocouple gas cooker Front panel assembly Programmer Control panel buttons Igniter connector assembly gas cooker Temperature regulator assembly and function switch Rotisserie motor assembly Convection fan assembly Bottom heater Convection fan heater Top heater Front wall Fittings Hob assembly ceramic hob cooker Energy metering device ceramic hob cooker Hob assembly electric cooker Cam connector of the hot plate Product identification Location of nameplate All the necessary information about the product can be found on the nameplate The nameplate of the freestanding cooker is located on the back wall The serial number The appliance serial number is printed on the nameplate The serial number is nec essary to match the correct spare parts for the product GAS ELECTRIC COOKER ee oc 5 906006 540111 MODEL 58GE3 43HZpTaDNAQ gt EN60 335 1 2 6 EN30 1 1 Voltage rating 230V 50Hz Type of gas G20 2H 20mbar Voltage of heaters 230V Total heat load 62. 1 Dismantle the hob dismantle the knob Disconnect the temperature regulator wiring harness Remove the two screws that fix the regulator uUBAUI MELO cs 1037 4 yp Ta 1s RAS Tke 2 To reassemble the components follow the above steps in reverse order Dismantling the function switch 1 Dismantle the hob dismantle the knob Disconnect the function switch wiring har ness Remove the two screws that fix the function switch IE A 2 To reassemble the components follow the above steps in reverse order 18 Rotisserie motor assembly Replacing the rotisserie motor 1 Dismantle the rear wall by removing the screws on the sides Disconnect the wir ing harness from the rotisserie motor Remove the two screws that fix the rotis serie motor A Y 2 To reassemble the components follow the above steps in reverse order 19 Convection fan assembly Dismantling the fan 1 Remove the rear wall according to relevant instructions in the manual Remove the fan guard by removing the screws Remove the fan propeller by holding the fastening nut with the pliers and rotating propeller 3 To reassemble the components follow the above steps in reverse order 20 Bottom heater Dismantling the bottom heater 1 Dismantle the rear wall by removing the screws on the sides Disconnect the wir ing harness from the heater Gently remove the oven insulation pay special at tention not to damage delaminate
3. To reassemble the components follow the above steps in reverse order 13 Front panel assembly Dismantling the front panel 1 Dismantle the door assembly Remove the two screws that fix the front panel to the freestanding cooker body The screws are located on the bottom of the panel and are visible after opening or dismounting the door Gently pull the panel to ward yourself 2 To reassemble the components follow the above steps in reverse order 14 Programmer Dismantling the programmer 1 Disconnect the wiring harness pry and unhook the programmer from the internal panel by pushing it to the outside 4 eA 2 To reassemble the components follow the above steps in reverse order 15 Control panel buttons Replacing the control panel buttons 1 Using a flat screwdriver pry the buttons catch and push the buttons to the out side 2 To reassemble the components follow the above steps in reverse order 16 Igniter connector assembly gas cooker Dismantling the igniter connector 1 Dismantle the knobs dismantle the front panel assembly Remove the washer located directly under the knob assembly on the valve stem Pry and turn the igniter assembly and remove it from the valve Repeat the procedure for all igniter connectors yi 2 To reassemble the components follow the above steps in reverse order 17 Temperature regulator assembly and function switch Dismantling the temperature regulator
4. 20 kW Total loading 3 1 kW Oven3 1 kW Gasrate 446 gih 24 W Grill 2 9 kW Category CZ SK II2H3B P Product s code 5401 Serial No een 1450 13 X Amica Wronki S A ul Mickiewicza 52 64 510 WRONKI POLAND Decoding the serial number An example of the serial number 99991111136513 9999 serial number in the batch of the product 11111 Product Code a unique number for each type of appliance 365 day of production 13 year of production Door assembly Removing the door assembly 1 Lift the lock of the left and right door hinge 7 pull out toward yourself 3 Place the door on a flat surface with the handle facing downward Using a flat screwdriver pry the cap of the profile on one side to remove it Door assembly 4 Pull out the inner glass panel and carefully lift it Do the same with the middle glass panel s 5 Remove the screw that fastens the hinge to the inner glass profile Pull the hinge out of the profile A Refer to the Annex to the SBI_001 service manual A T Door assembly 7 Remove the door handle by undoing the screws 8 To reassemble the components follow the above steps in reverse order Oven chamber seal Dismantling the oven chamber seal 1 Unhook the seal holders from the front wall in four places in the corners 2 To reassemble the components follow the above steps in reverse order The seal should be mounted with the joint
5. facing down Knob assembly gas cooker 1 Pry the knob s interior part squeeze both parts together and pull toward your self 2 To reassemble the components follow the above steps in reverse order Impor tant There is a spring between the two elements Oven shelves Dismantling the shelf supports 1 Remove the runners from the shelf supports unhook the shelf supports from the mounting holes Hea 2 To reassemble the components follow the above steps in reverse order 10 Hob gas cooker Dismantling the hob 1 To dismantle the cover assembly open it maximally to vertical position and pull it upward Remove the two screws that fix the hob to the freestanding cooker body u ra 2 e e A e a Era 2 Undo the screws that fix the burner bodies two screws for each burner if r A O eS 3 Gently push the burner body to the inside pay special attention not to damage the thermocouple and spark igniter 11 Hob gas cooker 4 Gently slide the hob toward the back and lift it 5 After dismantling the hob remove the old seal and after repair install a new seal when mounting the hob A 6 To reassemble the components follow the above steps in reverse order 12 Thermocouple gas cooker Replacing the thermocouple 1 Unhook the thermocouple from the valve Unhook the thermocouple lock located in the burner body prying it with a flat screwdriver ar N 3
6. ivets by drilling Do not use screws the service technician must have a riveter 24 Fittings gas cooker Replacing the burner body 1 Dismantle the hob spark igniter and thermocouple according to relevant instruc tions in the manual 3 To reassemble the components follow the above steps in reverse order 25 Fittings gas cooker Replacing the valve 1 Dismantle the hob dismantle the front panel assembly After dismantling or open ing the door remove the two screws that fix the gas pipe assembly to the cooker body 2 To replace the gas valve disconnect the thermocouple according to relevant in structions in this manual disconnect the pipe that supplies gas to the burner body 4 To reassemble the comparen follow the above steps in reverse order 26 Hob assembly ceramic hob cooker Replacing the cooking zones 1 Remove the screws that fix the hob in order to dismantle the hob Slide the hob toward the back 2 Place the hob upside down protect the cooking surface against scratching Re move the screws that fix the cooking zone 3 Press the spring that fixes the cooking zone in order to slide the cooking zone out 27 Hob assembly ceramic hob cooker Replacing the cooking zones When installing a new cooking zone install the spring in the same position as A in the old cooking zone If the spring is installed in a wrong manner the actual cooking zone will be shifted in rela
7. oduced on 2013 01 17 Those products are labelled with serial numbers lower than XX XXXXXXX17710 When ordering the hinge please give the appliance serial number to select an appropriate tension of springs in hinges Available hinges ATASAN DOOR HINGE PO802A1 2 8042000 Freestanding cookers 500 and freestanding cookers of 608 series ATASAN DOOR HINGE PO802B1 3 8042001 Freestanding cookers 600 and built in ovens glass x2 external and internal ATASAN DOOR HINGE PO802C1 4 8042002 Freestanding cookers 600 and built in ovens glass x3 external middle internal ATASAN DOOR HINGE P0802C1 5 8051075 Products with pyrolysis function and selected induction cookers When installing a glass assembly in a product manufactured before 2010 06 26 use obsolete glass suspension elements IS 003 EN 06 2013
8. s and freestanding cookers of width 500 and 600 for products manufactured with door assembly comprising Brerr s door Impl tation i ts mplementatiomin products hinge No changes were made to the design of product series 608 with convex door bulging outward Until 2010 06 26 Brerr s hinge longer non profiled U sections glued to the glass used in production From 2010 06 26 until 2013 01 17 Atasan hinge shorter non profiled U sections glued to the glass used in production Since 2013 01 17 new profiled U section glued to the glass Atasan hinge shorter used in production Obsolete element Obsolete element index New element index Strip glued on its entire length The assembly surface of the strip on glass was reduced there is a gap indicated on the For more efficient parts delivery please check if the customer s appliance is with or without the gap before ordering spare parts Obsolete elements may be used in new products YES New elements may be used in obsolete products CONDITIONALLY Additional modification In obsolete products also hinge must be replaced Obsolete hinge Brerr New hinge Atasan For door assembly hole plugs are added free of charge use them with a new hinge Additional notes When replacing door or glass assembly in products manufactured before 2010 06 26 additional two Atasan hinges must be ordered as the originally used hinges are not suitable for the new type glass assembly which was intr
9. the insulation Using a flat screwdriver gently deflect the catches securing the heater Slide the heater toward yourself we a ur m er z 2 To reassemble the components follow the above steps in reverse order 21 Convection fan heater Dismantling the convection heater 1 Remove the rear wall and the fan guard according to relevant instructions in the manual Disconnect the wiring harness from the convection fan heater Using a socket head wrench undo and remove the nut securing the heater assembly 2 Inside the oven chamber remove the screw securing the heater and pull the heater toward yourself 3 To reassemble the components follow the above steps in reverse order 22 Top heater Dismantling the top heater 1 Remove the rear wall according to relevant instructions in the manual Discon nect the wiring harness of the top heater Remove the nuts securing the heater to the oven chamber After unscrewing remove the heater from the oven chamber 2 To reassemble the components follow the above steps in reverse order 23 Front wall Dismantling the front wall according to IS 001 service manual 1 The rivets that fix the front wall to the appliance body must be removed by drill ing 1 f M8 pe bm gt ar Bu dir N E Rn PES vaT A 2 To reassemble the components follow the above steps in reverse order Install new rivets after the repair that required removal of r
10. tion to the marking on the hob Follow the numbers visible on the old and new cooking zones 4 To reassemble the components follow the above steps in reverse order 28 Energy metering device ceramic hob cooker Replacing the energy metering device 1 Dismantle the hob remove the knob by pulling it toward yourself Disconnect the wiring harness Remove the screws that fix the energy metering device Slide the energy metering device out 2 To reassemble the components follow the above steps in reverse order 29 Hob assembly electric cooker Replacing the cooking zones 1 Remove the screws that fix the hob in order to dismantle the hob Slide the hob toward the back 2 Place the hob upside down To dismantle the cooking zone undo the nut that fixes the cooking zone and disconnect the wiring harness 3 To reassemble the components follow the above steps in reverse order 30 Cam connector of the hot plate electric cooker Replacing the cooking zones 1 Dismantle the hob remove the knob by pulling it toward yourself Disconnect the wiring harness Remove the screws that fix the cam connector of the hot plate Slide the connector out 2 To reassemble the components follow the above steps in reverse order 31 5510001 Date prepared 2013 02 15 Service Information Bulletin 2013 02 21 Date changes made 2012 07 01 Type of change Glass assembly frame External glass assembly Built in oven
Download Pdf Manuals
Related Search