PA000472-03 Install and Service manual (UK).cdr
Contents
1. 24v DC Motor Fits silicone tube 6 4mm I D x 2 4mm wall Programmable drink shot size or free flow 2 x 5 litre disposable bag in box Installation 1 Remove cardboard packaging from machine 2 The following components should be provided with the machine Mains lead Plastic funnel Water inlet hose Anti tilt bracket 2 off thumb screws for anti tilt bracket 2 off tube clips Measuring cylinder Drip tray and grille 2 off Mixing valve assemblies Spare rings small for mixing valve Spare O rings large for mixing valve Pot of food grade silicone grease Plastic bottle full of tank water conditioner 3 Remove machine from transportation pallet by unscrewing the two thumb nuts either side of the unit 4 Locate the unit on a suitable surface with a depth of no less than 600mm no more than 1 metre from a standard 3 4 water stop valve and electrical socket Installation contd 5 Slide drip tray and grille into position in base of machine 6 Fit the mixing valve assemblies Note A small amount of food grade silicone grease provided in the installation kit should be applied to the O rings to aid assembly This should be reapplied after every cleaning 1 Disposable cap 2 Mixing chamber 3 Small O rings 4 Large O ring 5 Mixer 6 Spout Installation contd 7 Fill the water tank Without electrics or water connected remove lower rear cover 1 Pull out fill pipe 2 Remove and ret2. Fig 10 6 Slide back Armaflex and disconnect the two pipes carrying chilled water around the cabinet Numbers 3 amp 4 Fig 10 7 Slide the unit out of the machine Reverse the process to re fit the fridge unit Ensure all water connections are securely made and do not leak Armaflex to be repositioned over pipe joints 10 Parts list refrigeration deck 11 Parts list refrigeration deck Condenser Brazed Assembly Compressor 3 Compressor 006 8 Agitator Motor Assembly 9 Pressure Gauge Water Pump Assembly 12 Parts list door assembly Parts list door assembly Door Compression Seal LED Strip Wired Assembly Diffuser Diffuser 4 Door Curve Assembl Product Selection Button PCB Assembly Low Bag Light LED PCB Assembl Downlighter PCB Assembl Button Overlay Assembly 1 or 3 button selection 14 Parts list dispense module 5 1 MSS hej A BEAN NAJ 15 Parts list dispense module CPC Coupling Flow Control Valve Motor and Gearbox 006 8 16 rea list display a Parts MIZ Tr ZT UUN PENN 3 mat 17 Parts list display area Door Safety Switch Light Switch 18 m S Parts list misc LN Mel 7 19 x Parts list misc i 6 5 Drip Tray Grille Drip Collection Tra Adjustable Foot 20 Tr
3. ain plug in end of pipe Insert funnel 3 provided in the installation kit Pour in tank water conditioner provided in the installation kit Fill the tank with 8 5 litres of clean water If too much is inserted it 0 overflow from the tube in the front of the machine into the drip ray Remove the funnel and replace the plug into the end of the pipe Push the fill pipe back inside the machine Installation contd 8 Connect the water and electrics Remove the protective cap from threaded inlet 4 Fig 3 Connect the Mains Water Inlet Hose to threaded inlet 4 Fig 3 We recommend that a shutoff tap be fitted to allow isolation from the mains water supply when necessary Switch the water supply on and check for leaks Connect the power lead to connector 5 Fig 3 Switch on and leave for a minimum of 1 hour to stabilise temperature before calibrating the water flow rate 9 Flush through the water system Set the dispenser to Flush mode by switching from Run to Flush Switch is located in the top left hand corner of the control panel Position a suitable container under the left or right dispense nozzle as appropriate Press and hold the dispense button on the front of the door until the water flow from the nozzle is clear and free from trapped air and sanitisation fluid It is recommended that at least 1 litre of water is flushed through each dispenser on installation 10 Calibrate the wat
4. autonumis Bravanti machine Installation and Service Manual This guide contains instructions on how to install and service Autonumis Bravanti machines Document PA000472 Issue 3 Note Installation of this equipment should be undertaken by a trained and authorised engineer Contents Specification 2 Installation procedure 3 Changing from single to multi volume dispense 8 Removal of fridge deck 9 Parts list 11 Troubleshooting 21 Wiring diagram 23 Due to our policy of continual product improvement any diagrams and illustrations of the product and or its component parts contained within this document may appear different from that those supplied However the contents of this document and the functionality of the product and or its components that it describes remain unaffected 298 ooo JOO OOO ooo E Weight Electrical Water connection Water pressure Refrigeration Brix adjustment Pump Portion control Product capacity Specification 640 EEE A Dry 55 5 kg Packed 62 5kg Installed 64 5kg UK EU 230v 50hz 3 4 BSP hose connection Minimum dynamic water pressure 2 5 Bar Maximum dynamic water pressure 8 Bar Pressure regulated in machine to suit site conditions R134a Hermetic compressor Concentrate storage compartment chilled to 4 C Electronic control Easy load peristaltic pump with 3 roller rotor
5. bracket using the two M5 thumbscrews provided Fig 6 Juice packs can now be fitted and the correct Brix level and drink shot sizes set as described in the Operators Manual Changing from single to multi volume dispense 1 Slide Single Dispense Panel upwards to remove and replace with Multi Dispense Panel Fig 7 i 4 0 a s 2 Slide the Dil Switch on the rear of the Push Button PCB behind the Dispense Panel area from left to right Fig 8 This illuminates and activates all three dispense buttons In single volume dispense only the middle button is illuminated and active 25446NLD 1 APENS M2 Removal of fridge deck The fridge deck can be removed from the machine to enable easier access to chiller components It is recommended that the chiller is emptied of water by syphoning or pumping before removal to make the unit lighter Remember to re fill the chiller with 8 5 litres of clean water on reassembly see page 5 for details 1 Remove the Mains Water Inlet Hose and Power Lead 2 Remove the Upper and Lower Rear Covers 3 Remove the M6 Socket Head Screw in the top left hand corner of the compressor compartment Fig 9 4 Remove screw attaching earth wire and disconnect 8 way electrical connector Number 1 Fig 10 Removal of fridge deck contd 5 Slide back Armaflex and disconnect the pipe carrying chilled water to the dispense module in the front of the machine Number 2
6. e Check door is fully closed Replace switch Check fuses replace PCB Troubleshooting contd FAULT POTENTIAL CAUSE SOLUTION Drink not cold enough Refrigeration system failure Check compressor condenser fan agitator motor thermostat etc Replace as necessary nn en Machine noisy Fan failure Check condenser fan and inner cabinet cooling fan LCD display not No power to cabinet Check power supply to cabinet working corrupted Main PCB failure Check fuses replace PCB LCD header assembly failed Replace LCD display Ni Dispense button s not Machine is set for multi volume Change to single dispense see working dispense with single dispense Fig 8 panel fitted Product Selection Button PCB Replace faulty PCB Assembly failure 22 Wiring diagram Low Voltage this side of dotted line Condensor Fan Compressor amp Condensor fan are controlled by ice bank thermostat only Fuses shown are 5x20mm HRC 1amp T Cy Main circuit board Compressor Mains inlet and EMC filter N ACin Fuses where fitted zur Er Mains Water Inlet Controlled by relay on main board Ice bank Thermostat Agitator Agitator runs all of the time on some models and only during water dispense on others Low Voltage this side of dotted line DANGER High Voltage this side of dotted line Mains Transformer PA machine wiring diagram Sheet 1 High Voltag
7. e wiring diagram Not to scale Circulation Pump runs all of the time Wiring diagram Remote 12v regulator Sheet 2 Low voltage wiring Fuses 5x20mm 3 15A F Light Switch m g Configuration DIL switch Main circuit board Red Tracer 1 DANGER High Voltage this side of dotted line LCD module top view Door safety switch kills pump motors Flush Switch Yellow loom Left button board 24vdc axial fan runs all of the time Water control valve E Left solenoid Blue wire Right pump Green wire Orange wire 24vdc u Right solenoid white wire Left pump Pump Motors L 8 R low bag mg iil lights where fitted 24 Not to scale LED light strip 12v White loom Right button board Orange loom 12v downlighter circuit board autonumis Autonumis Ltd Cirencester Rd Tetbury Gloucestershire GL8 8SA United Kingdom Tel 44 0 1666 502641 Fax 44 0 1666 504397 27
8. er flow rate 1 Gauge 2 Adjusting knob Installation contd 10 Calibrate the water flow contd Pull the adjusting knob 2 in the direction shown in Fig 4 until a click is heard The regulator is pre set and will only require a small adjustment With the display reading Machine Ready press and hold both the Set and 1 buttons together for 5 seconds The machine will reset and then display Calibrate Place the measuring cylinder supplied under one of the dispense _ nozzles and press any of the corresponding drinks buttons This will dispense a measured shot of water into the cylinder This should measure 200ml 2ml If the volume is incorrect correct as necessary by turning the adjusting knob clockwise to increase the volume or anti clockwise to reduce the volume Once the correct volume has been achieved push the adjusting knob back in the opposite direction to that shown in Fig 4 until a click is heard This locks the pressure regulator and prevents inadvertent adjustment of the pressure Press the Set button to exit Calibrate and return to Machine Ready Return the machine from Flush to Run mode by pressing the switch in the top left hand corner of the control panel Replace the rear cover 11 Secure the anti tilt mounting bracket in the desired location on the chosen surface using suitable fixings Fig 5 Secure the machine to the anti tilt mounting
9. oubleshooting Fuse failed in plug if fitted 9 0 fuse blown Fuse on rear of machine blown EE DD DI po LED failure 0 gt Machine not dispensing water Cabinet in Out of Service mode Dispense module not connected properly Water supply not connected or turned off Water frozen in cooling coil Water inlet solenoid failed shut shut failed shut Main PCB failure Machine in Flush mode mode empty connected properly Concentrate tube has sealing clip still connected Dispense module not connected properly Door not closed properly Door safety switch failure Main PCB failure Machine not dispensing concentrate 21 SOLUTION Check power supply to cabinet Check fuse and replace Check fuses and replace Check fuses and replace Check light switch is on Replace relevant LED board Return to Machine Ready status Check water and electrical connections to dispense module Check connections and stop tap Unplug dispenser and defrost Check thermostat Ensure thermostat probe is fully located into tube in tank Replace water inlet valve Open up and recalibrate Replace flow control valve Check fuses replace PCB Return to Machine Ready status Return to Machine Ready status Replace box refill container Check connection and tube is correctly routed through pump Remove clip Check water and electrical connections to dispense modul
Download Pdf Manuals
Related Search