Touch Key Workshop v3.0 User's Guide
Contents
1. 4 SCL ICPCK 5 6 RESB 7 8 VDD VDD 9 10 GND GND The MCU pin usage is as follows MCU Class BS82B16 3 A BS83A04A 3 A BS83A04A 4 A BS83B12 3 B BS83B12A 3 A BS83B12A 4 A BS83B16 3 B BS83B16A 3 A BS83B16A 4 A BS83C24 3 B BS84B08A 3 A BS84C12A 3 A Rev 1 00 29 of 31 May 23 2014 y xipuaddy Touch Key 6 Rev 1 00 nor OF Workshop v3 0 User s Guide www holtek com Appendix B Evaluation back board cautions If evaluation back board is connected with a battery the power cannot be turned on during or before downloading otherwise it will affect programming If there is no any operation for about 2 minutes after the power is turned on the power will be automatically turned off 30 of 31 May 23 2014 g xipuaddy nor PA www holtek com Touch Key Workshop v3 0 User s Guide Copyright 2014 by HOLTEK SEMICONDUCTOR INC The information appearing in this Data Sheet is believed to be accurate at the time of publication However Holtek assumes no responsibility arising from the use of the specifications described The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise Holtek s2. PC6 e Y E A f 1 Pc2 Q KE KEY14 PCS sall 3 PC3 C KEY12 KEY13 Pc4 2 Add a component Drag a component from the toolbox into the IC block shown by the blue box in the diagram to complete the settings Key or component property setting When dragging a key or a component from the toolbox its property settings will be displayed in the properties window The following figure shows the key threshold value setting If the properties window is blank this means that the key has not had any properties setup Properties n x EEY1 ec 2 ls Threshold 16 Apply all key Rev 1 00 12 of 31 May 23 2014 uonelado pue suonoun3 M S doysx10m Ady yano HOLTEK www holtek com Touch Key Workshop v3 0 User s Guide Change the key or component pin setup The already setup pins shown in red can be directly dragged to other I O pins which have a KEYx label When dragged the pin colour will change to green If the colour turns red then the pin setup is complete If the colour of the dragged pin does not change to red then this means that the pin could not be changed For example to change the SDA pin in the Scope component to PC7 just drag the SDA directly to PC7 pin until the colour turns red OCDSSDA PAS PA3 OCDSSDA 1 OCDSSCK OCDSSCK S W Functional Description Menu Functional Description OEA s View gt Open V Download P d i ei Ei 2 EM rees SR ee IR al
3. content is blank when Save is first executed it will generate C ASM AEX and CEX with the name of the component directory automatically For example the component directory sets LEDX4_V10 and the development language selects asm then it will generate LEDX4_V10 asm LEDX4_V10 AEX and LEDX4_V10 CEX in the component directory Rev 1 00 26 of 31 May 23 2014 u0118 13U35 JUDUOdWION nor HA www holtek com Touch Key Workshop v3 0 User s Guide Project Edit Lookin EQ EE HOdrE E vepx4_v20 asm 3 Mu Recent Documents p LA Desktop Mu Documents PE Mu Computer File name LED V20 asm Add My Network Files of type Source Files asm as cl Cancel Files in project Ehop touch Key Yvorkshop hicuLibrary Peripheralss LEDad vw ED SA v2 asm Oe __ Delete hove Up gt Move Down 1 The MCU name which supports the component should be setup in the Misc area 2 The component description files can be setup in the Help Document area With regard to documents it is recommended that PDF files are used and that they should be placed in the component library location Rev 1 00 27 of 31 May 23 2014 4011 3435 juauodulo Touch Key Workshop v3 0 User s Guide nor OF www holtek com Component programming m Program structure users need to implement two subroutines named using the component names Rev 1 00 lt component
4. User can change to another 1 0 Port pin Jl Use 1 0 port control register Output asm define LED p C define LED1 Specify the component name and it will appear in the toolbox of the Touch Key Workshop Specify the folder name for the component library path The folder is required for proper placement of the component system files the related program code files and the component help documents Its root directory is the McuLibrary Peripherals directory under the platform installation path As an example if the platform installation path is C Program Files Holtek MCU Development Tools Touch Key Workshop then the folder should be located in C Program Files Holtek MCU Development Tools Touch Key Workshop McuLibrary Peripherals Component pin setup will setup the component pins combined with the MCU I O pins These settings also affect the software display If the component does not have a corresponding pin then it is not necessary to implement this setup After setting the Component pin setting the right side can be clicked in sequence for the detailed settings 24 of 31 May 23 2014 u0118 13U35 JUDUOdWION nor HA www holtek com Touch Key Workshop v3 0 User s Guide e Step 2 Global Option fe Component System File Maker Component name EEE Location McuLibrary Peripherals LE v10 Fin setting Global Option Lian
5. the installation el Setup Holtek Touch Eey Workshop 3 Select Start Menu Folder Where should Setup place the program s shortcuts n Jop Setup will create the program s shortcuts in the following Start Menu folder To continue dick Next If you would like to select a different folder dick Browse loltek MCU Development Tools iTouch Ke Worksho Rev 1 00 6 of 31 May 23 2014 u01 8 81SU M S pue uononpouj woed juaudojanag nor HA www holtek com Touch Key Workshop v3 0 User s Guide e Step 4 To add a desktop shortcut check Create a desktop icon fe Setup Holtek Touch Eey Workshop 3 Select Additional Tasks Which additional tasks should be performed Rev 1 00 7 of 31 May 23 2014 UOUEIIEISUL M S pue uononpouj WO e g jJuaudo anag nor OF www holtek com Touch Key Workshop v3 0 User s Guide e Step 5 Confirm the settings click Back to return to the the previous steps to modify if necessary or click Install to complete the installation el Setup Holtek Touch Eey Workshop 3 Ready to Install Setup is now ready to begin installing Holtek Touch Key Workshop V3 on your computer Destination location Cy Program Files Holtek MCU Development Tools Touch Key Workshop lopment Tools iTouch Key Workshe Rev 1 00 8 of 31 May 23 2014 UOUEIIEISUL M S pue uononpouj woed juaudojanag nor HA www holtek com Touch Key Workshop v3 0 User s Guide e St
6. ART If the TUNING_IIC in the Touch Key Workshop is selected then the IIC protocol will be used If TUNING_UART is selected then the UART protocol will be used Rev 1 00 22 of 31 May 23 2014 uone1ado pue suoiouny M S Bumn sy y noL nor HA www holtek com Touch Key Workshop v3 0 User s Guide 4 Component Generation Touch Key Workshop is an open platform in which advanced users can create their own component library which can be shared with other users Component Library System File Maker Users can execute the Component Library System File Maker in the start menu to call up this creation function TE EverPro 1000 d vc HOPE3000 Ey HOPESO00For22B tsMCU A M HOPE3000For8051 MCU A E HOPE2000forEIC300 Hi m HT IDE2000 e HET Editor P Holtek USB Workshop Je Touch Eey Workshop b Holtek Touch Key Tuning GG Holtek Touch Key Workshop fey Uninstall Holtek Touch Key Workshop F gt Component TI Maker Rev 1 00 23 of 31 May 23 2014 4011 3435 juauodulo Touch Key Workshop v3 0 User s Guide pore OF www holtek com Maker instructions e Step 1 Pin setting kuch Rev 1 00 E Fe Component System File Maker Component name LEDX4 J Location McuLibrary Peripherals LEDX4_V10 i GET Pin setting Globel Option Libren Component Pin ca x Configure Js Connect to MCU I O pin LED Pen LED ES e ll Ex PAD PB1 EES
7. BV413 Note If there is an old project in start interface you can click New to create a new project and then operate according to the above steps to 4 Rev 1 00 10 of 31 May 23 2014 uone1ado pue suoloun M S doysyx10m Aoy YOnoL nor HA www holtek com Touch Key Workshop v3 0 User s Guide Add keys and components 1 Add a key Method 1 Drag a KEY from the toolbox to the IC pin position labeled KEY as shown below Toolbox T Xx Key EEY y TUNING WC vin de TUNING UART 203 Component fo LED matrix 4X8X 2 100 e OUTPUT_1 H OUTPUT_2 y OUTPUT_A Release the left mouse button and it will change to the condition shown below where the original PBO name changes to the key function ko PEO PB1 KEY2 SEH D PB2 0 KEYS Rev 1 00 11 of 31 May 23 2014 uone1ado pue suoioun 4 M S doysyx10m Aoy YOnoL nor OF www holtek com Touch Key Workshop v3 0 User s Guide Method 2 Drag a KEY from the toolbox into the IC block shown by the dotted box The touch keys will be automatically arranged in a KEY1 KEY2 etc order PBO KEY1 PAI EJ P a PB1 KEY2 PAS ew pa PB2 KEY3 PA3 ol e y T E KL xd PB3 KEY4 OCDSSDA PAO 1 PB4 KEYS OCDSSCK PAZ E dl ol PB5 KEY6 PA7 T EC d PB6 KEY7 vob Ee e PB7 KEY8 vss E 4 PCO KEY9 KEY16 PC7 I Pci KEY10 KEY15
8. Choose the touch software library version MCU Configuration Options For normal users the MCU options are not required to be setup so the default options can be used Click the red framed block below to make changes if necessary Rev 1 00 15 of 31 May 23 2014 uone1ado pue suoljoun 4 M S doysyx10m Aoy yYOnoL HOLTEK www holtek com Touch Key Workshop v3 0 User s Guide Global Option Window Global Options a x Normal Debounce Times 90 mS Auto Calibration Pe x OU Um High Sensitive Maximum Key Hold Disable One Key Active The global option window provides the touch key parameter for user setup The available touch key parameters are shown in the accompanying table Name Range Debounce Times 50ms 190ms Auto Calibration Period 62 5ms 937 5ms High Sensitive O Normal Sensitive 1 High Sensitive check Maximum Key HoldTime Disable 4 sec 60 sec One Key Active O Off 1 On check Fast Response Auto Frequency Hopping O Off 1 On check O Off 1 On check Power Save Noise Protect O Off 1 On check O Off 1 On check Moving Calibration O Off 1 On check Note 1 Here it is necessary to check Advance Mode 2 Options will vary according to the library version Rev 1 00 16 of 31 May 23 2014 uonelado pue suono9un3 M S doysx10m Ady YONOL nor HA www holtek com Touch Key Wor
9. ave CITE mode EX Hew Build HT IDE3000 OR EE Rezister Upgrade e Link e Link EFW Pooqect HT LE3000 Tuning e Link Rev 1 00 13 of 31 May 23 2014 uone1ado pue suoioun 4 M S doysyx10m Aoy y noL nor OF www holtek com Touch Key Workshop v3 0 User s Guide Home Menu Functions m New Create a new project Open Open an already saved project file Save Save the current edited project Build Build project e Download If checked the program will be downloaded to the board after successful compilation The board must not be connected to an external power supply or batteries when downloading e OCDS mode If checked components must not be setup on the pins labeled OCDSSDA and OCDSSCK m HT IDE3000 Advanced users can use the HT IDE3000 to continue to develop the project After executing the HT IDE3000 the Touch Key Workshop will be switched off automatically If the user s computer is not installed with the HT IDE3000 then it will be in a gray state m Tuning This is used to fine tune the Touch Keys to obtain the optimal sensitivity and touch parameter adjustments If TUNING components are not chosen such as TUNING_UC and TUNING_UART this column will be in a gray state m Register e Link Note that the e Link must be registered before use If registered it will be in a gray state m Upgrade the e Link F W This will upgrade the e IsoLink firmware or change the e link to be used for other purposes other than t
10. e Option m K Output Pe 2define o Middle define Selection UT Label Define value Program GND D VCC 1 Propestes n x LEDE4 as 2 E OU TEUT LE GND m GND After setting the software screen is shown in the accompanying diagram Rev 1 00 25 of 31 May 23 2014 4011 3435 juauodulo HOLTEK www holtek com Touch Key Workshop v3 0 User s Guide e Step 3 Library E Component System File Maker Component name LEDX4 Location McuLibrary Peripherals LEDx4_V10 Pin setting Global Option Libusay Develop Language Em w i Source Files Note Below files should be put to the location of component library File Name Add to HT IDE3000 s Project LEDX4_V10 asm Yes a 124 3 LEDX4_V10 AEX No 65338 164 3 LEDX4 V10 CEX No BSS4B084 3 BS84C 124 3 Help document Note Document files should be put to the location of component library Note The output middle file s name will be the same with location folder s name 1 Select the development language C language or assembly language The C language compiler can only use the V2 version at the present time 2 Set the component used code file in the source file If Yes is selected to Add to HT IDE3000 s Project then the HT IDE3000 will add the files to the project as shown in the following figure 3 If the source files
11. e can display the key values Users can check the list on right side of the Scope window to observe the corresponding selected key waveforms CH K B K D 5 O o tse Y upper Y kwer se 0 em Functional Description m Automatic Scale If checked the software will automatically setup the Y axis display range otherwise the Y upper and lower limits will need to be setup manually m Start Stop Start or stop the Scope display m Reset Clear the waveform and reset the pressed key count value and time in the tuning window Menu Functional Description AE bad wegl View al E Open 4 Register eLink FPirwsue verion Lib FAW version Protocol IK H de nem de aera CheOl4 10 Mew el Es Set PE E INCH H Powex 5 07 mM Pech 4 e Link Tarzet ben m New Create a new Touch Key Workshop project m Open Open a previously saved Touch Key Workshop project file m Save to INC H Touch Key setting output saved to HXT_REFERENCE me m Register e Link The e Link must be registered before use If this area is highlighted then the e Link has already been registered m Upgrade firmware Upgrade the e IsoLink firmware or change the usage for non Touch Key e Link use m Power Set the e IsoLink to provide power to the target board There are 5V 3 3V or external power supply options m Protocol Select the communication protocol between the target board and the e IsoLink There are two kinds of interface IIC and U
12. e will be displayed after which Next should be selected to proceed with the installation i setup Holtek Touch Eey Workshop Y3 Welcome to the Holtek Touch Key Workshop V3 Setup Wizard This will install Holtek Touch Key Workshop V3 version 3 0 on Your computer Itis recommended that you close all other applications before Click Next to continue or Cancel to exit Setup 4 of 31 May 23 2014 u01 8 81SU M S pue uononpouj WO e g juaudojanag nor HA www holtek com Touch Key Workshop v3 0 User s Guide e Step 2 Setup the installation folder the default folder is C Program Files Holtek MCU Development Tools Touch Key Workshop and click Next to continue the installation ie Setup Holtek Touch Eey Workshop 3 Select Destination Location Where should Holtek Touch Key Workshop V3 be installed lind Setup will install Holtek Touch Key Workshop V3 into the following folder To continue dick Next If you would like to select a different folder dick Browse Program Files Holtek MCU Development Tools Touch Key larkshor At least 46 3 MB of free disk space is required Gs Rev 1 00 5 of 31 May 23 2014 u01 8 181SU M S pue uononpouj W10JJe d jJuaudo anag nor OF www holtek com Touch Key Workshop v3 0 User s Guide e Step 3 Setup the start menu folder the default folder is Holtek MCU Development Tools Holtek Touch Key Workshop and click Next to continue
13. ep 6 The completion dialogue will be shown after the installation is completed If the Launch Holtek Touch Key Workshop box is checked the S W will be executed after the Finish button is clicked a Setup Holtek Touch Key Workshop 3 Completing the Holtek Touch Key Workshop V3 Setup Wizard Setup has finished installing Holtek Touch Key Workshop V3 on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup Rev 1 00 9 of 31 May 23 2014 u01 8 81SU M S pue uononpouj woed jJuaudojanag nor OF www holtek com Touch Key Workshop v3 0 User s Guide 2 Touch Key Workshop S W Functions and Operation S W Development Flow Set the project name GEES geed Advanced users project path and MCU option Ree H Note Tuning needs additional Tuning component Quick Start Create a new project 1 In the Project Name location in the project window enter a project name 2 In the Project Location set the project path the default path is the same as that of the HT IDE3000 After the project has been created it will generate a new subdirectory with the same project name in the directory to store any related files 3 Choose the MCU that is to be used in the project 4 Choose the touch library version Project D x Se zl Project Name Project Location C Users brucelee Do MCU BS82C164 3 Touch Library Vers B582C164 LI
14. kshop v3 0 User s Guide Properties Window When dragging a component its properties can be set in the properties window or by clicking on the added component to change its properties If a component does not require additional settings then the properties window will be blank The key properties are setup as follows Pioperhes a x EEY1 ez 2 Threshold 16 Apply all key The Key trigger threshold value has a range of 8 255 Check Apply all key and adjust the threshold values of the other keys Rev 1 00 17 of 31 May 23 2014 uone1ado pue suoloun 4 M S doysyx10m Aoy YOnoL norec www holtek com Touch Key Workshop v3 0 User s Guide 3 Touch Key Tuning S W Functions and Operation The Touch Key Tuning functions provide users with a software interface to observe the key signals as well as providing a platform for touch key sensitivity and parameter adjustment The platform allows users to observe the results immediately after adjustment In addition to being used via the Holtek Touch Key Workshop the tuning software can also be used independently Quick Start Touch Key Tuning 1 After running from within the Touch Key Workshop the tuning software menu screen is shown as follows gaa s Horre View Open y Register eLink Fiwarwe version Lib FAW verson gt al pave Uperade Frage LI 2 Power 50V Project e Link Target bad 2 After executing the tuning software the following screenshot
15. lick on the key to observe it in more detail fd Ln Key State Display The actual detected difference is shown in the green block the greater the difference is the more the green area is 01 UU When the key is pressed it will be displayed in red as shown in the diagram here KEY1 is pressed and the key flag is setup in the program 01 Rev 1 00 20 of 31 May 23 2014 uonelado pue suono9uny M S Burn Aey yonoL nor HA www holtek com Touch Key Workshop v3 0 User s Guide The displayed numbers in the key icon are described in the following diagram 01 gt Key No 0006 Offset Cap 0016 Threshold 1 D Background o Signal Tuning Window The Tuning Window can observe a single key signal value and adjust the key sensitivity Tuner n x Switch Key Original 1026 Count of the Ke Background 1036 A gt A Threshold 16 Aner 1 1 S SCH Signal Strength 10 ime Offset Cap 0 Ge SE time amp gt Single Strength Adjust sensitivity of Key 8 255 Threshold Rev 1 00 21 of 31 May 23 2014 uoljei9do pue suoi oun M S Pulung Aey y noL nor OF www holtek com Touch Key Workshop v3 0 User s Guide Global Option Window The Global Option Window provides touch key parameters which the user can change Users can observe the adjusted results immediately after the setup values are changed Refer to Page 16 Global Option Window for the touch key parameters Scope Window The Scop
16. name gt _INITIAL For the component initialization at power on e g LEDX4_V20_INITIAL lt component name gt Component functional program entry e g LEDX4_V20 m File naming rule The files need to be named the same as the folder m File structure It is necessary to provide at least three kinds of files with extension names as follows C ASM Place the main program for the component If the development language is the C language then the extension name is C If the development language is assembly language then the extension name is ASM AEX Use assembly language syntax to locate the label of the external output e g EXTERN _LEDX4_V20_INITIAL NEAR EXTERN _LEDX4_V20 NEAR CEX Use C language syntax to locate the function name of the external output e g extern void LEDX4 V20_INITIALO extern void LEDX4_V20 28 of 31 May 23 2014 u0118 13U35 JUDUOdWION nor HA www holtek com Touch Key Workshop v3 0 User s Guide 5 Appendix A The e IsoLink F W will automatically identify the MCU type used for evaluation and define the e IsoLink pin Two examples follow A Pin PC ICP OCDS 1 2 SDA 3 a 4 SCL 5 ICPDA O2D 6 ICPCK O2C 7 gt 8 VDD VDD VDD 9 E 10 GND GND GND B Pin PC ICP 1 2 SDA ICPDA 3
17. nor BE Touch Key Workshop v3 0 User s Guide Revision V1 00 Date May 23 2014 IMD holtek com Touch Key Workshop v3 0 User s Guide pore OF www holtek com Table of Contents 1 Development Platform Introduction and S W Installation oococooocccoonanoo 3 Characte n SiC S a 3 Sic AA an 3 SV Cle OM UI e 3 A 4 2 Touch Key Workshop S W Functions and OperatiOND ccoocnncccnnccccconcccccnnanconnnaoos 10 SW Ree Eu Te Geen nett Meee net ae eerste erate ner ect arene mnr ee Sue NraT re gene ne Seer eeeere een erer 10 OCK E O 10 E A eer ee ere ne ae eee eee eee 10 Add keys and COM PON Nt E a a a 11 Key or component Property nd WEE i Change the key or component pin SetUpP EE EEN als SA ele elos EE 13 Menu Functional E o EE 13 TOODOXNING OW E e a r E ea Eg ey ee me ene eee are eee ee 15 A OW E TAE 15 alobal tie a RL ele 16 Proper oo a dl nl eee EA o ea 17 3 Touch Key Tuning S W Functions and Operation ccccscssseessesseeseeseeneeenees 18 Elei Tu 18 Fei teil SV TUNN ME 18 Sy Ml aul E leie GE 19 Towel Key Signal Observation O EE 20 HE UNG THANG V A ato A EE 21 GlobalkOption Window E 22 SCIO en s eo EE EE EE 22 MENA are A Ee aide 22 4 Component Generator toda 23 Component Library System File WE 23 Maker instructions E es PPP 24 SAMP e nl un Une E 28 EE EE EE 29 o elt EE 30 Rev 1 00 2 of 31 May 23 2014 U9 U04D JO 3 48 nor HA www holtek com Touch Key Worksho
18. ouch keys Lea OR ng Pore View vd Toolbox Mf Project Y Help Avealable Language English d wf Pioperhes MCU Resource d Global Ophons Chitput view Language View Menu Functions In this menu various information can be selected for display on the workshop working area Functions such as Toolbox Properties Global Options Project MCU Resource Output and Help can be selected for display in the corresponding Window In the Available Language section select the appropriate language for workshop use from a choice of presently available Traditional Chinese Simplified Chinese and English Rev 1 00 14 of 31 May 23 2014 uonelado pue suonoun3 M S doysx10m Ady yano Touch Key Workshop v3 0 User s Guide Toolbox Window nor HA www holtek com Here keys and components are provided for users to add functions Toolbox Key ab KEY Tong a TONING II 101 dj TONING UART_ 203 Component tj LED mati A 3937 4100 di OUTPUT_1 H OUTPUTA il OUTPUT 4 e OUTPUT_S Project Window Project az 2 E i up ato Project Name Project Location MCU Touch Library Versi ax tkprj C Users holtek Docu BS83B16A 3 BS83B16A_LIBV413 m Project Name Enter the project name Note that after a Save operation the project name can not be changed later MCU Choose the MCU that is to be used Project Location Set the project path the default path is the same as the HT IDE3000 Library Application
19. p v3 0 User s Guide 7 Development Platform Introduction and S W Installation The HOLTEK Touch Key Workshop V3 is a third generation platform using an intuitive drag and drop methodology for touch switch project implementation It fully integrates the touch software library compiler function key signal monitor and parameter adjustments functions Characteristics m Supports BS82xxx BS83xxx BS84xxx Flash series MCUs Provides friendly and intuitive operation interface Easy key sensitivity and parameter adjustment Integrated compiler Integrated touch control and peripheral library Advanced users defined component libraries System requirements m PC with USB interface m Operation system Microsoft Windows XP or above System Configuration 10 pin connector Rev 1 00 3 of 31 May 23 2014 u01 8 181SU M S pue uononpouj W10J1e d juaudo anag Touch Key Workshop v3 0 User s Guide pore OF www holtek com m S W Components e Holtek Touch Key Workshop Used for MCU key setup touch parameter setup program generator and compiler functions e Holtek Touch Key Tuning key signal monitor sensitivity adjustment and touch parameter adjustment m H W Components e e soLink Used for OCDS In Circuit Programming ICP and data uploading e Target board Used for functional verification S W Installation Rev 1 00 e Step 1 When starting the software installation the following welcome dialogu
20. products are not authorized for use as critical components in life support devices or systems Holtek reserves the right to alter its products without prior notification For the most up to date information please visit our web site at http www holtek com tw Rev 1 00 31 of 31 May 23 2014
21. will be displayed It is necessary to select the target board and e IsoLink transmission protocol first which is set in the Protocol section of the software with a default protocol of IIC After this the power supply for the target board can be setup d Com Dee NM z Wier gt Hore dE eS pen lg Register eLink Bram version Lab FAW verion Protocol IC Target bom af Hew Game to MEH Project Rev 1 00 18 of 31 May 23 2014 uone1ado pue suoiouny M S Bulun sy y noL nor HA www holtek com Touch Key Workshop v3 0 User s Guide S W Functional Description k Jg il Hegle tee x JS E Hami Vaw Bech T w gt ko d Fima erpen A ena Poca 10 mmm Y pa y 1 eg a omm a i Treme EA 1 oO ml gr 7 a a Calibrate Time x 5000057 y a Tom 2 D m nl 1090 E el 1039 Tel 1024 Tel 1031 Description Key No 1 Touch Key signal observation area 2 Tuning Window 3 Global Option Window 4 Scope Window Rev 1 00 19 of 31 May 23 2014 uoie1ado pue suonoun3 M S Pulung sy y noL nor OF www holtek com Touch Key Workshop v3 0 User s Guide Touch Key Signal Observation Area From the touch key signal observation area whether the pin is defined as a touch key or I O pin it can be observed within this area If the pin is used as an I O pin then it will be grayed out as shown below If the pin is used as a touch key then users can c
Download Pdf Manuals
Related Search