IM-250SW User Guide
Contents
1. PCB of OUTPUT the unit or the previous one 4 Try to use another DMX controller 5 Check to see if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit 1 If you use a controller with 5 pins DMX connector you need to use a 5 to 3 pin adapter C Some units don t respond to the easy controller 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug cable from the output of the h You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal N Wrong DMX address in the unit Set the proper address w Nor n h n unit to the input of the next unit The cable cannot be branched or split to a Y cable O TESpONSE tO NE Sung o_o DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or Make sure the unit is not receiving DMX signal corroded connectors can easily distort the signal and shut down the system 2 Check microphone to see if it is good by tapping the microphone 4 The DMX output and input connectors are pass through to maintain the DMX circuit E One of the channels is not working well when power is disconnected to the unit 1 The stepper2. internal pressure there might be a risk that the Discharge lamp would explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp MSD 250W NSD 250 2 W 1 Always switch off the main supply and never handle the lamp or luminaire when it is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding ee 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp any longer than its specified life 5 Make sure the lamp is located in the center of the reflector for the best spot 4 How To Set The Unit 4 1 Control Panel OLY POR O O O O REMOTE CONTROL SENSITIVITY OME MASTER SLAVE SOUMD DMX OUTPUT DMX INPUT Display To show the various menus and the selected functions LED DMX input present aa Master mode SAVE On swem Button MENU To select the programming functions DOWN To go backward in the selected functions To go forward in the selected functions ENTER To confirm the selected functions Remote controller input By connecting to CA 8 to co
3. motor might be damaged or the cable connected to the PCB is broken 5 Each lighting unit needs to have an address set to receive the data sent by the TeHiolors drive l on ihe Pee might be our ot condition controller The address number is between 0 511 usually O amp 1 are equal to 1 2 F The lamp is cutting out intermittently The end of the DMX512 system should be terminated to reduce signal errors o_o The lamp is not working well Check the main voltage either too high or too low Internal temperature may be too high Check and if necessary replace the fan on the head 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal M 18 19 G If The pan belt is broken 1 Turn off the main power 2 Unscrew all the screws A and open the base housing cover B 3 Unscrew all the screws C and open the arm cover D 4 Unplug all the connect wires that from the arm to the bottom 5 Unscrew the screws E and remove the fixture head 6 Loose the screws F then loose the screws G 7 Change a new belt H put the belt around the axis gear and motor gear 8 Screwed the screws G install the new belt and adjust the belt tension properly Note do not fix belt too tight as it is easy to rupture 9 Plug all the connect wires back that form the bottom to th
4. same type Make sure there are no flammable materials close to the unit while operating as it is fire hazard Use safety chain when fixes this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is Ta 40C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85C Don t touch the housing bare hand during its operation and allow about 15 minutes to cool down before replacing bulb or serving as the unit could be very hot In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack Do not touch any wire during operation as there might be a hazard of electric shock Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using Hot lamp explosion hazard Do not open the unit within five minutes after switching off Do not start on the unit without bulb enclosure or when housing is damaged The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Do not look directly at the light while the b
5. then the unit will focus on tilt 0 pan 0 pan 90 pan 180 pan 270 in every pressing ENTER button To go back to the functions press the MENU buiton again t z 5 tl Self Test Press the MENU button up to when the C cSt is blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again l I IUI Ambient temperature of lamp Press the MENU button up to when the EEN is blinking on the display Pressing ENTER button and the ambient temperature of lamp will show on the display To go back to the functions press the MENU button again iil lI Pott Fixture Hours Press the MENU button up to when the is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again 1 OAD Lit ut Lamp ON OFF Press the MENU button up to when the Laie button and the display will blink Use DOWN and UP button to select the Lon Lamp on or off Lamp off mode Once the mode has been selected press the ENTER button to setup Idling 8 seconds automatically exit menu mode Back to the functions without any is blinking on the display Pressing ENTER change press MENU button Reset Press the MENU button up to when the C Sor is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard posi
6. 0 047 Color S 032 039 Color4 024 031 Color3 016 023 Color2 0068 015 Color 1 000 007 OFF 248 255 Stopped 171 255 D 246 255 Stopped Prism affect 2 245 Fast 245 Fast a 135 Slow 121 134 Stopped 121 134 Stopped 086 170 Prism affect i BIT PAN 120 Siow 3 5 O10 Fast O10 Fasi 120 Slow 16 BIT TILT 16 000 009 Stopped 000 085 Open 000 009 Stopped 0 Normal 16 17 5 5 DMX512 Connection 6 Troubleshootino The DMX512 is widely used in intelligent lighting control with a maximum of 512 FOLOWMO are a TEW COMMON provem Inat May Cec Ur AUNG Operon TETE are some suggestions for easy troubleshooting channels 1 2 3 4 A The unit does not work no light and the fan does not work 1 Check the connect power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 Ifthe DMX LED is on and no response to the channel check the address settings and DMX polarity DMX512 COMMON 120 ohm 1 4W DMX INPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pins DMX of the last fixture 3 Ifyou have intermittent DMX signal problems check the pins on connectors or on
7. Pressing ENTER button and the display will blink Use DOWN and UP button to select the Gi normal or SL id 2 light show mode Once the mode has been selected press the ENTER button to setup Idling 8 seconds automatically exit menu mode Back to the functions without any change press MENU button Blackout Mode Press the MENU button up to when the bid is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the yes blackout or no blackout mode Once the mode has been selected press the ENTER button to setup Idling 8 seconds automatically exit menu mode Back to the functions without any change press MENU button Pan Inversion Press the MENU button up to when the is shown on the display Pressing ENTER 10 button and the display will blink Use DOWN and UP button to select the Ino normal or HTT pan inversion mode Once the mode has been selected press the ENTER button to setup Idling 8 seconds automatically exit menu mode Back to the functions without any change press MENU button Tilt Inversion Press the MENU button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the Ino normal or iT tilt inversion mode Once the mode has been selected press the ENTER button to setup Idling 8 seconds automatically exit menu mode Back to the functions without any change press MENU
8. To go back to the main functions without any change after 8 seconds 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogrammed function 2 By easy controller 3 By universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 1250 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 14 5 1 Master Slave Built In Preprogrammed Function Once you control the unit by Built In program be sure the unit is setting on mode via menu By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to select show show 1 2 3 4 modes for the first unit master Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to set in slave mode and select Gi normal or Gi 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave LED lights will constantly on 2 light show In slave mode SRI T fmeans the unit works no
9. Z Solution Your integrated Solution LINKABLE STAND ALONE IM 250SW User Guide Please read these instructions carefully before use 1 Safety Instruction N Please read carefully the instruction which includes important information about the installation usage and maintenance TABLE OF CONTENTS WARNING 1 Safety Instruction 2 Technical Specification 3 Lamp 4 How To Set The Unit 4 1 Control Panel 4 2 Main Function 4 3 Home Position Adjustment 5 How To Control The Unit 5 1 Master Slave Built In Preprogrammed Function 5 2 Easy Controller 5 3 DMX Controller 5 4 DMX 512 Configuration 5 5 DMX 512 Connection 6 Troubleshooting 7 Maintenance and Cleaning Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before fuse lamp replacement or servicing Replace fuse lamp only with the
10. button I l l Lt Led Display Press the MENU button up to when the is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the M Led on or off Led off mode Once the mode has been selected press the ENTER button to setup Idling 8 seconds automatically exit menu mode Back to the functions without any change press MENU button White Balance Press the MENU button up to when the ENTER button and will blink on the display use DOWN and UP button to adjust the value from 125 to 255 press ENTER button to store and will blink on the display use DOWN and UP button to adjust the value from 125 to 255 press ENTER button to store and will blink on the display use DOWN and UP button to adjust the value press ENTER button to store Idling 8 seconds automatically exit menu mode Back to the is showing on the display Pressing functions without any change press MENU button Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to when the is blinking on the display Use the ENTER button to change to the mode the MENU button 11 Display normal mode for the fixture putting on the floor oor i Display inversion mode for the fixture fixing under ceiling Vv Focus Adjust Press the MENU button up to when the is blinking on the display Pressing ENTER button the unit will focus on tilt 90 and
11. e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 23 EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN 55103 1 1996 EN 55103 2 1996 EN 61000 3 2 2006 EN 61000 3 3 1995 A1 2001 A2 2005 amp Harmonized Standard EN 60598 2 17 1989 A2 1991 EN 60598 1 2008 EN62471 2008 Part 1 General requirements and test Following the provisions of the low voltage directive 73 23 EEC and 93 68 EEC Innovation Quality Performance
12. e arm 10 Reverse the procedures from point 5 to point 2 20 F If The tilt belt is broken 1 Turn off the main power 2 Unscrew all the screws A and open the right arm cover B 3 Unscrew the screws C the screws D and screws E that fix the bridge 4 Change a new belt F Please adjust the tension of the belt properly Note do not fix belt too tight as it is easy to rupture 5 Reverse the procedures from point 3 to 2 21 Pay attention to the belt tension when install the belt Please refer to the photos below Photo 1 Adjust bet tensionthrough loose the screw Photo 2 22 7 Maintenance and Cleanino Maintenance ignitor Ballast A As the pictures shown above if the cable or cable joints turned yellow or black please replace the cable or cable joints immediately B Do maintain the fixtures every two months and make sure that all the screws and terminals have been locked firmly to make sure the normal performance of the fixtures Negligence of maintenance would cause malfunction of the fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics e Clean with soft cloth using normal glass cleaning fluid
13. en 5 metal gobos 2 glass gobos are included Gobo wheel rotates with variable speed giving shaking effect Effect Wheel Prism Rotating Prism Movement Pan 540 in 2 8 second Tilt 270 in 1 6 second DMX Channels Channel 1 Pan Channel 12 Prism Rotation Channel 2 Tilt Channel 13 Focus Channel 3 Pan Tilt Soeed selection Channel 14 Pan 16 bit Channel 4 Dimmer Channel 15 Tilt 16 bit Channel 5 Shutter Shaking Channel 16 Reset Lamp on off Channel 11 Prism 5 Luminous intensity 14460 4500 1900 lux _ 9 7 Distance m Dimension 428 x 369 x 466 mm Lx W x H Weight 23 kg te CO I 369 2 1 Inserting Exchanging rotating gobos DANGER Install the gobos with the device switched off only Unplug from mains before changing gobos Open the cover by loosening the fastening screw at the sides of the cover If you wish to use other forms and patterns as the standard gobos or if the gobos are to be exchanged remove the fixation ring with an appropriate tool Remove the gobo and insert the new gobo Press the fixation ring together and insert it in the front of the gobo CAUTION Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switching off WARNING Because of its high
14. ntrol the unit for Stand by Function and Mode function Sensitivity To adjust the sound input sensitivity DMX input output For DMX512 operation use 3 pin XLR plug cable to link the unit together 8 4 2 Main Function To select any of the pre set functions press the MENU button up to when the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are shown below fidd H ema DMX512 Address Setting Lio be GH Show mode 1 Pui La E show mode 2 Show mode 3 Show mode 4 Slave Mode Normal Slave mode 2 Light Show Blackout Mode Yes Blackout Blackout Mode No Blackout ro Heo Pan Normal Hi Pan Inversion Liu 4 f i RE O Bajka Faj 1 lem J Bea io D ore ino Tilt Normal LETTT Tilt inversion MENU Lan LEDon EST L DEF LED off roog paLa D259 White Balance Doos eea PoP Display Normal 2 LUON Display Inversion tad Focus Adjust 0 255 EPSt Self Test Enp Ambient temperature of lamp 7 i TH Y E Ta Fixture Hours ra Lon Lamp on jt L HFF Lamp off i SP Reset DMX512 Address t Press the MENU button up
15. o go back to the Please refer to the following diagram to address your DMX512 channel for the first 4 units 255 z 240 247 Color 30 a2 299 Color 29 224 7341 Color 28 216 223 Color 27 208 215 Color 26 200 207 Color 25 192 199 Color 24 184 191 Color 23 176 183 Color 22 k 168 175 Color 21 DMX 512 Configuration 160 167 Color 20 152 159 Color 19 Pd i For DMX reset put DMX value of CH 8 amp CH 16 to 255 the unit will reset after about five 136 143 Color 17 l 55 p Slow 248 255 Open iF Ph kaad i aed i Slow gt ea BD 240 247 Fa mo ES TESEN l Fasi ian A bda o 239 Fast shaking Fost 2 128 Siw mm LERA A 115 127 Pink a T ri 1027 114 Light groan j a 132 Slow shaking 2 069 101 UW purple bdi l Tre N 131 Fast shutter OTT 088 Blue 70 5 Mia 064 076 Red s a 051 063 Yellow 1 fry 039 050 Light blue ie ea a fhe 16 Show shuiter bch Ah r j 026 038 Magenia r an OO4 015 Open ST IG 013 025 Grean i OD 007 Blackout OO0 012 While o seconds 128 135 Color 16 120 127 Color 15 co rion Rotten o For lamp off put DMX value of CH 8 to 239 amp CH 16 to 255 112 119 Color 14 104 111 Color 13 li For color sound activated put DMX value of CH 6 to 248 255 For gobo sound activated put DMX value of CH 9 to 248 255 248 255 5 4 DMX 512 Configuration 201 247 191 200 096 103 Color 12 088 095 Color 11 OBO0 087 Color 10 072 079 Color9 064 071 Color 8 056 063 Color 048 055 Color 04
16. rmally and Gi d means 2 light show In order to create a great light show you can set Gi d on the second unit to get contrast movement to each other even if you have two units only 5 2 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote control on the first unit will control all the other units for Stand by Function and Mode Stand by Blackout the unit Strobe X Y moving show pattern Gobo Color selection X Y moving setting 1 Color sync strobe selection 1 Hold on for gobo 1 Macro sound active 2 Sync strobe Show 1 Show 4 selection 2 Fade sound invalid 3 Two light strobe Please refer to 4 2 Main 2 Press for color change Functions Show mode Mode Sound 1 Sound 2 Slow Sound 3 Position Latch LED off LED slow blinking LED on LED fast blinking 5 3 DMX Controller If you use a universal DMX controller to control the units you have to set DMX address from Function 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the noe is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address 15 Once the address has been selected press and keep ENTER button pressed up to when DMX 512 Configuration the display stops blinking or storing automatically 8 seconds later T
17. tion It will cost about 20 12 seconds and then automatically exit menu mode DMX RESET Set DMX value of channel 8 and channel 16 to 255 then all channels of the unit will return to their standard home position 4 3 Home Position Adjustment Press MENU button for at least 5 seconds into offset mode to adjust the home position when you want to adjust pan and tilt home position you should be run mode first the functions are shown below Focus Adjust Q 255 A co a LIC oc La SPARH Pan offset 0 512 LF MENU Hor EL Smag Tilt offset 0 2048 E a ian HauobH m 7 Gobo offset 127 127 Sar ioLOL r yA Color offset 127 127 ee I I vit Focus Adjust Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the is shown on the display Pressing ENTER button the unit will focus on the center position Use DOWN and UP button to adjust focus this settings only for offset mode to adjust home position To go back to the main functions without any change after 8 seconds Pan offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the pan home position Once the position has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU but
18. to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup Idling 8 seconds automatically exit menu mode Back to the functions without any change press MENU button 5 E i d Show Mode Press the MENU button up to when the Shi fa is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the Gi i show 1 or Gh ol show 2 or show 3 or ama show 4 mode Once the mode has been selected press the ENTER button to setup Idling 8 seconds automatically exit menu mode Back to the functions without any change press MENU button Sh Show 1 mode Fixture is placed on the floor Tilt movement angle 210 Sh el Show 2 mode Fixture is fixed under ceiling Tilt movement angle 90 m m TEET Show 3 mode Fixture is placed on the speaker The spot is always projecting to the audience s direction i e in front of the stage Pan movement angle left to right to left 160 Tilt movement angle 90 60 above horizon 30 below horizon Show 4 mode Fixture is fixed under ceiling The spot is mainly projecting in front of the stage Pan movement angle left to right to left 160 Tilt movement angle 90 vertically front 75 back 15 Slave Mode Press the MENU button up to when the is shown on the display
19. ton again To go back to the main functions without any change after 8 seconds Tit offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button 13 up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the tilt home position Once the position has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds Gobo offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the gobo home position Once the gobo has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds Color offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the OL is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the color home position Once the color has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again
20. ulb is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs by yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its screw holes on the bracket please refer to the drawing below Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit s weight Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture The equipment must be fixed by professionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it safety chain Power supply AC 120V 60Hz or AC 230 240 250V 50 60Hz Light Source MSD 250W NSD 250 2 W LED Total 12pcs Red 4pcs Green 4pcs Blue 4pcs Optical system High efficiency optical system High quality optical lens and dichroic colors Beam angle 13 Shutter Dimmer Blackout 0 100 smooth dimming and strobe speed variable 1 10 flashes per second Color wheel Independent color wheel with 9 trapezoid dichroic colors plus white Color wheel rotates with variable speed giving rainbow effect Gobo wheel Independent gobo wheel with 7 rotating interchangeable gobos plus op
Download Pdf Manuals
Related Search