Radon Sentinel™ User's Guide
Contents
1. 28 Troubleshooting 29 Radon System Error Codes 29 Contacting Sun Nuclear Support 30 Radon Support Web Page 30 Regulatory Supplement 31 ConventionS sonaa a aaaeeeaa 31 Sun Nuclear Corporation Symbols 31 Operator Responsibility 32 Operating Information 32 Additional Information 32 About Radon 2 oa ua doce ewe eon aes 32 Iaex ea 6 eae ded Saw as Be 35 This page is intentionally left blank vi Introduction Description The Radon Sentinel is a patented detection device to measure the concentration of radon gas The unit is designed for professional inspectors to use in homes and buildings The Radon Sentinel is a continuous radon monitor that can be operated using an AC adapter or four size C alkaline batteries The 16 character display on the Radon Sentinel shows instructions and radon readings Buttons below the display are used to enter data set parameters and display data values The Radon Sentinel connects to a computer via a USB cable and the Continuous Radon Monitor software can then be used to download measurements set parameters and print reports See Radon Monitor Software on page 11 Note Radon support is available 24 hours a day 7 days a week on the lt P Sun Nuclear Support web site For more information see Contacting Sun Nuclear Support on page 30 Parts Unpack the Radon Sentinel and verify that the parts described2. 3 Press EPA AVG CUR 4 again to display the average radon concentration over the total monitoring period 4 Press EPA AVG CUR 4 a third time to display the average radon concentration over the last 12 hour period Clearing Memory Note Before clearing the memory ensure that any test data that you wish to save has been downloaded to your computer When the memory is full that is there are two tests in memory the messages Memory Full and Download Data alternate on the Radon Sentinel display These messages will appear when both memory slots have stored test data The memory is cleared using the keys on the Radon Sentinel The instructions below are written for a unit with two tests in memory 1 I Ifatestis in progress stop the test See erminating a Test on page 8 2 Press CLEAR 5 3 Clear Jest 2 appears on the display briefly followed by the prompt Confirm Y 7 N 2 Press 1 to continue 4 Test 2 Cleared displays followed by the prompt Clear Jest 7 5 Confirm Y 1 N 2 appears Press 1 to confirm or 2 to keep Test 1 In memory Replacing the Batteries When the batteries are low or need to be replaced a message displays on the Radon Sentinel The message will vary depending upon whether an external power source is used Low No Battery Battery does not have enough power for a 60 hour test Replace Battery Replace the batteries as soon as convenient Current test can continu
3. SUN NUCLEAR Corporation Radon Sentinel User s Guide ACCURATE RELIABLE ECONOMICAL Your Partner In Radon Measurement User s Guide Radon Sentinel 2013 by Sun Nuclear Corporation All rights reserved The information contained in this manual and the accompanying software program is copyrighted and all rights are reserved by Sun Nuclear Corporation Copying duplicating selling or otherwise distributing any part of this product without the prior written consent of Sun Nuclear Corporation is prohibited Sun Nuclear Corporation reserves the right to make periodic modifications of this product without obligation to notify any person or entity of such revision This guide is written for PC software version 3 0 2 Embedded firmware version 1 0 The Model 1030 Radon Sentinel is protected by U S Patent 4 871 914 Radon Sentinel is a trademark of Sun Nuclear Corporation Document 1030012 Rev B 1 April 2013 T SS s corporation SUN NUCLEAR Preface Intended Use The Model 1030 Radon Sentinel is intended to be used by radon measurement professionals for measurement of the indoor radon level in human dwellings Typical Application applications only Using in an outdoor environment may cause errors CAUTION Radon Sentinel Model 1030 should be used for indoor due to humidity and extreme temperatures For a typical test place the Radon Sentinel in a building or structure to
4. 11 Recommended System Requirements 11 Installing Software 11 Installing on Windows XP Operating System 11 Installing on Windows 7 Operating System 13 Launching the Software 14 Closing the Software 14 Software Setup 15 Configuring Company Information 15 Radon Monitor Details 16 Retrieving Data from the Monitor 17 Displaying Test Summary Data 18 Setting up Customer Information 19 Test Chart Views 20 Saving a Test 00 21 Open a Saved File 21 Previewing and Printing Test Data 21 Preview Raw Data 21 Print Raw Data 22 Customer Reports 22 Preview Report 22 Print Report 24 Save PDF cseeeaws ona c etd cdeeaes 24 Specifications 25 Model 1030 Radon Sentinel Specifica HO arg ee een ee a 25 Radon Software Recommended System Requirements 26 Service 0 ccc 27 Maintaining Hardware 27 Parts and Repairs 27 Storage ss oo edgar bo ee ee eR 27 Cleaning seerde iin ei ne eth oy 27 Disposing and Recycling 27 Battery Life nauan aaaa naaa 27 Maintaining Software a7 Verifying Software Version 27 Removing Software 28 Multiple Software Installations 28 Service and Calibration
5. Value 0 1 to 9999 picocuries liter pCi l or 1 becquerels per cubic meter Bq m to 99 99 kilo becquerels per cubic meter kBq m3 20 or 1 pCi l whichever is greater after 24 hours Detector Measurement Interval Test Duration Sensitivity Diffused junction photodiode e Model 1028 quantity 1 Model 1029 quantity 2 e Model 1030 quantity 6 Active volume 9 4 cm Dome volume 63 cm3 0 5 1 2 4 8 12 16 20 or 24 hour intervals selectable by user 1 12 24 36 48 60 72 84 96 100 999 hours selectable by user maximum of 720 measurements e 1028 3 counts per hour per picocurie per liter cph pCi e 1029 6 counts per hour per picocurie per liter coh pCi e 1030 15 counts per hour per picocurie per liter cph pCi l Display 16 digit reflective LCD display Green LED light emitting diode indicates USB to PC Status Light Keypad connection 6 digit membrane switches with multiple functions Disturbance Sensor Environmental sensors Operating Environment Storage Environment USB Data Port Inertial switch report shows M for motion e Temperature Oto 120 2 degrees F 18 to 49 1 degree C e Pressure 10 to 15 0 5 psi 69 to 104 kPa 3 kPa e Humidity 20 to 90 relative humidity 5 45 to 95 F 7 to 35 C e 20 to 90 relative humidity non condensing e 22 to 122 F 30 to 50 C e 10 to 90 relative humidity non condensing USB connector a
6. Store the Radon Sentinel in an indoor protected environment Do not store the device in the trunk of a car for extended periods Keep the device dry Cleaning Clean the unit with a soft dry cloth Do not use liquid cleaners solvents or abrasives Disposing and Recycling Do not discard unit as waste the circult board contains small amounts of lead Recycle the components In accordance with local regulations Battery Life Any type of size C battery will operate the Radon Sentinel but an alkaline battery provides a good balance between long life and cost Since battery capacity varies widely between types of batteries and even between individual batteries of the same type the predicted battery life of 300 hours using fresh alkaline batteries An individual unit may have longer or shorter life Maintaining Software The CD distributed with the Radon Sentinel contains the latest released software version as of the shipment date however upgrades or patches may be available later When available these upgrade can be downloaded from the Sun Nuclear Radon Support web page For more information see Contacting Sun Nuclear Support on page 30 Verifying Software Version 1 Launch the Continuous Radon Monitor software 2 Connect to the radon monitor 3 Select Help gt About from the menu The About Radon Monitor message displays the version number of the software 27 Removing Software To remove the Continuous Radon Monitor
7. There is no power switch or key sequence to power on off the Radon Sentinel When the AC power adapter is connected the monitor display is on continuously indicating that the power is successfully connected If power is removed or if running on batteries alone and no buttons are pressed for 3 minutes the display turns off automatically If the display is not on press any button After a few seconds the display turns on Figure 4 and shows the battery status The number of bars indicate battery status Radon Sentinel S ni stn ane nape tones apace mili Figure 4 Turning on the Display The display prompts for the PIN personal identification number entry see Personal Identification Number on page 7 Then the company name displays momentarily if set up followed by the message Ready to Test Ifa testis not started the settings for Duration Interval and Delay appear If there is data in memory the message Data in Memory appears When Aeady to Test displays a test can be started the setup can be changed or status for the following can be displayed EPA average or current radon values temperature pressure or humidity The display turns off automatically after approximately 3 minutes of inactivity when the AC power is not connected There is not an OFF switch or key sequence to power off Controls LCD Display view messages status and instructions of current operation START STOP start or stop a
8. application iil B batteries inserting 3 replacing 9 battery life 27 buttons keypad 5 Cc calibration 28 caution high humidity may shorten battery life 3 character set 16 cleaning 27 clearing memory from keypad 9 closing software 14 company information configuring 15 editing 16 computer recommended requirements 26 retrieving data from monitor 17 two or more 28 configure company Information 15 connect computer to radon monitor 9 power 3 controls 5 conventions 31 customer info test views 19 customer information 19 customer support Radon 1 D description radon monitor 1 disconnecting USB cable 10 display radon monitor data 16 turning on 4 display turns off 4 5 display values EPA AVG CUR 8 E ending atest 8 EPA AVG CUR 8 error message hardware 29 software 29 errors system 29 H humidity affects battery 3 l information application help 32 installing software 11 K keypad buttons 5 M main screen software about 15 maintaining hardware 27 software 27 monitor two or more 28 O open a saved file 21 operating information 32 operation standalone 3 operator responsibility 32 options and accessories 2 P parameters configure using radon monitor keys 6 parts 27 personal identification number 7 PIN 7 PIN default 15 positioning the monitor 7 preview raw data 21 print raw data 22 report 24 R Radon customer support 1 radon monitor AC power 4 battery requirements
9. 3 calibration 28 connecting power 3 description 1 details 16 disposal 27 intended use iii introduction 1 parts 1 positioning 7 recycling 27 service 28 software 11 Radon Sentinel specifications 25 raw data preview 21 print 22 repairs 27 report print 24 reports customer 22 preview 22 S save a test 21 set up parameters 6 software about 11 closing 14 error messages 29 inspection company view 15 installing 11 launching 14 main screen about 15 multiple installations 28 removing 28 requirements 26 retrieving data from monitor 17 36 upgrade 27 using 11 verifying version 27 specifications technical 25 standalone operation 3 starting a test 8 status checking 7 storage 27 support request 30 telephone 30 symbol legend 31 synchronize time with computer 16 system errors 29 T test starting 8 terminating 8 test chart view 20 tripod using 7 troubleshooting 29 two or more computers 28 radon monitors 28 U USB cable disconnecting 10 using a tripod 7 wW warning unit contains high voltage circuits do not open case 28 web site radon 32 Warranty 1 Instrumentation a This instrument and its accessories excluding those listed in 1 D below are warranted by SUN NUCLEAR CORPORATION against defects in materials and workmanship for a period of one year from the date of original purchase from SUN NUCLEAR CORPORATION During the warranty period SUN NUCLEAR CORPORATION will repair or at its
10. Monitor software 2 f more than one device is connected select the device to work with from the drop down list above the toolbar and then click Get Data Information about the selected radon monitor displays Figure 13 3 To synchronize the time on the Radon Sentinel with the time on the computer click Syne Time with PC 16 72101001 Help L Preview Raw Data L Preview Customer Report Print Raw Data Print Customer Report BF Open ld Save D Get Data J Refresh Devices Use Test 1 For Report O Use Test 2 For Report Sse eee eee eee eee Inspection Company Test 1 Customer Info Test 1 Chat Test 2 Customer Info Test 2 Chart 2 Save PDF Y Company Information on Monitor Model Number 1030 Serial Number 72101001 Device information Saveto Device est data downloaded from the Radon monitor Test 2 Start Time Units Hours Delayed Duration Measurement Interval Measurements Overall Average EPA Average Start Time 3 9 2013 2 04 PM Units pCi I Hours Delayed 24 hour s Duration 24 hour s Measurement Interval 1 hour s Measurements 24 Overall Average 0 2 EPA Average 0 2 Company Sun Nuclear Corporation Addressi 415 Pineda Court F Calibration Factors Address2 calibration 2 265 5 288 3 282 62 79 City Melbourne factors State Province FL Battery Voltage 2 61 volts Calibration Date 5 18 2012 ZIP 3
11. be monitored connect power and leave it unattended for the required test period Ambient room air laden with radon diffuses into the radon monitor s detection chambers Gaps between the base and the cover allow air to freely pass into the radon monitor Radon decay by products emit alpha particles which are detected by the photo diodes and then counted During a test the number of counts produced by the alpha particles is stored in memory and converted into radon concentration pCi l using the stored calibration factor At the end of the test period the results can be viewed on the radon monitor display on a computer screen or in a printed report After viewing or printing the report data clear the memory Two tests can be stored before the memory is cleared the second test in memory is intended for use as a backup in case the data cannot be conveniently downloaded The radon monitor can be moved from the test site and the report printed later The instrument is completely reusable and requires no supplies except line power and or four size C batteries Health and Safety Instructions contain explosive gases A spark from inside the radon monitor could WARNING Never use the radon monitor in an area that could ignite an explosion e To protect insulation never pull on a cable to disconnect it Always grasp the plug or connector e Inspect the device periodically for damage If measurement errors or device damage are suspected
12. below are included in the package When unpacking save the packing material to use when sending the Radon Sentinel to Sun Nuclear Corporation for annual calibration No Description 1 Model 1030 Radon Sentinel 2 Cable USB 2 m 3 AC to USB power adapter 5VDC 100 240V USB CD software and reference information not shown User s Guide on CD Getting Started Guide not shown Included with the Radon Sentinel but may be ordered as an accessory Figure 1 Parts Furnished with Model 1030 Radon Sentinel Options and Accessories Contact Sun Nuclear Corporation to order any of the following accessories Table 1 Radon Sentinel Accessories Part Number Description 102378 Sign self adhesive Warning Closed Building Procedure 102379 Sign plastic hanging Caution Radon Test in Progress 1028130 Sign vinyl static cling Warning Closed Building Procedure 1030000 SC Heavy duty case for Radon Sentinel Model 1030 only Radon Sentinel Operation Connecting Power The Radon Sentinel can be operated on battery power or it can be connected to AC power When the Radon Sentinel is connected to AC power the battery provides back up power Inserting Batteries Disconnect the Radon Sentinel from AC power before installing batteries A new set of four size C alkaline batteries will operate the device for 300 hours power adapter when using the Radon Sentinel in areas with high CAUTION High humidity m
13. contact Sun Nuclear Corporation Regulatory Information For a definition of the symbols used throughout this document and additional information related to user and device safety see Regulatory Supplement on page 31 Review this information thoroughly before setting up and using the instrument Contents Preface 000 cece eens iii Intended Use jii Typical Application lil Health and Safety Instructions iii Regulatory Information IV Introduction 05 1 Description wads nadestoe dots oer es 1 FS 1 Options and Accessories 2 Radon Sentinel Operation 3 Connecting Power 3 Inserting Batteries 3 Connecting the AC Adapter 4 Turning on the Display 4 CONTTOlIS seiere Biden gm octane Ja acd 5 Configuring Parameters 6 Set Parameters using Radon Sentinel Keys 6 Personal Identification Number 7 Positioning the Monitor 7 Checking Unit Status 7 Starting a Test cas a lt ciaededusddiad 8 Terminating a Test 8 Displaying EPA Average and Current Radon Values 8 Clearing Memory 9 Replacing the Batteries 9 Connecting Radon Sentinel to COMPUTE dey eee44 beeen ata ue 9 Disconnecting the Radon Sentinel 00 10 Radon Monitor Software 11 About the Software
14. is displayed to the user or a cross referenced subsection within this manual e Text in single quotes indicates the name of a window or dialog box Sun Nuclear Corporation Symbols The following symbols are used in this document and in Sun Nuclear Corporation s product labels A WARNING Possible impact to personal safety AN CAUTION Cautionary statement lt P Note Important or supporting information ual Manufacturer s Identification name and address mi Date of Manufacture S N Serial Number RE f Catalog Number Bu Consult instructions for use 31 Operator Responsibility This guide is intended for an operator who is experienced with the use of radon detection devices The device and its accessories must not be used for any purpose other than described in this manual Violation may result in loss of warranty Operating Information e Do not use any cable that is damaged or has broken insulation Replace the cable immediately e Do not permit water or any other liquids to spill onto the instrument e Inspect all cables periodically for damage If any mechanical or electrical degradation is suspected contact Sun Nuclear Corporation for repair or replacement Additional Information Application Helo Help is available by selecting Help gt Contents from the menu bar of the Continuous Radon Monitor software The application help contains the same information as the Radon Sentinel User s Guide
15. m 123456 zP 123456 is installed working Click to navigate Phone Number to location of photographs Enter a caption and click to add up to 6 photos to the inspection rel Clicking on a selected photo will allow it to be excluded from the repo Mitigation System Exists Picture Caption Mitigation System Working Inspection Site Photos After importing photos click ona photo to exclude from report click again to Include the photo Unsaved Data Figure 15 Entering Customer and Site Information 19 Test Chart Views The Jest 7 Chart and Jest 2 Chart tabs show a chart or graph of the test results The chart is included in the test report If two tests are downloaded from the Radon Sentinel est 7 Chart will display the data for test 1 and Jest 2 Chart will display the data for test 2 Use the instructions below for viewing the chart data 1 After downloading test data click the Test 1 Chart tab 2 Select Test 1 Chart in the navigation panel Figure 16 er x 72101001 Help A Open Save GetData J RefreshDevices UseTest1ForReport UseTest2ForReport _ z i L Preview Raw Data L Preview Customer Report Print RawData Print Customer Report Save PDF gt Inspection Company Test 1 Customer Info Test 1 Chart Test 2 Customer Info Test 2 Chart Continuous Radon Monitor Model 1030 S N 72101001 boxes to customi
16. option replace an instrument found to have such defect at no charge to the customer THERE ARE NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OF FITNESS WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF THIS EXPRESSED WARRANTY EXCLUDES COVERAGE OF AND DOES NOT PROVIDE RELIEF FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE INCLUDING BUT NOT LIMITED TO LOSS OF USE LOSS OF SALES OR INCONVENIENCE THE EXCLUSIVE REMEDY OF THE PURCHASER IS LIMITED TO REPAIR RECALIBRATION OR REPLACEMENT OF THE INSTRUMENT AT THE OPTION OF SUN NUCLEAR CORPORATION This warranty does not apply if the product as determined by SUN NUCLEAR CORPORATION is defective due to either abuse misuse or modification or service performed by someone other than a SUN NUCLEAR CORPORATION authorized repair and calibration facility Misuse and abuse include but are not limited to subjecting the instrument to environmental conditions outside the specified limits or allowing the instrument to become contaminated by radioactive materials In order to obtain warranty repair service the instrument must be returned freight prepaid to the facility cited in 3 b below The purchase date vendor invoice or customer purchase order should be included along with a statement of the problem Instruments will be returned transportation prepaid to points within the United States Because the original manufac
17. software from the computer use the instructions below for the operating system installed on the computer Windows XP 1 Open the Control Panel and then select Add or Remove Programs 2 Inthe list of programs select Radon Monitor and then click Remove This will remove all of the radon monitor program files Windows 7 1 Click Start gt Settings gt Control Panel then select Programs and Features 2 Inthe list of installed programs select Radon Monitor and then click the Uninstall button Multiple Software Installations e Two or More Radon Sentinel Units The Continuous Radon Monitor software only needs to be Installed on a computer one time regardless of the number of radon monitor units being used with that computer When connecting to a radon monitor the software identifies the serial number of the connected radon monitor and creates a unique serial number directory for each radon monitor instrument During measurement the setup template includes the serial number which is validated against the radon monitor instrument communicating data to the PC e Two or More Computers f you have more than one computer the radon monitor software may be installed on each Service and Calibration WARNING The unit contains high voltage circuits Do not open the case There are no user serviceable parts inside For service or calibration return the unit to Sun Nuclear Corporation as instructed in the Warranty statement on the in
18. was h mm ss tt the file can only be opened on a computer configured with the same settings Launch the Continuous Radon Monitor software 2 On the toolbar click Open 3 When the Open Past Inspection window displays browse to the directory where the text files are stored select the desired file and then click Open The data is populated in the software Previewing and Printing Test Data Raw data is the test data that is downloaded from the Radon Sentinel and saved to a txt file on the computer Previewing and printing the raw data requires that the test results be saved to a file Preview Raw Data The txt file can be opened in a viewer by clicking Preview Raw Data on the Continuous Radon Monitor software toolbar The data in the txt file is used to create a report Raw data cannot be edited See Saving a Test above 21 Download test data and save It see Saving a Jest on page 21 or opena saved file see Open a Saved File on page 21 Click Print Raw Data The data opens In a separate Print Preview window Use the toolbar buttons to view the data Maximize window View the window in full screen mode Zoom Increase or decrease the magnification of text Auto 500 200 150 100 75 50 25 10 Page layouts One page Two pages Three pages Four pages Six pages select the number of pages to fit in a single window Close Close the preview window Pages right side Scroll through the pages usi
19. 2940 Monitor Date and Time 3 19 2013 4 41 PM Phone 123 456 7890 Sync Time with PC License Number 123456789 Personal Identification Number 1234 Unsaved Data Figure 13 Radon Monitor Information Retrieving Data from the Monitor 2 Note Jo retrieve data from the Radon Sentinel the display on the unit should show READY 10 TEST TEST COMPLETE or MEMORY FULL Connect the Radon Sentinel to the computer and launch the Continuous Radon Monitor software The serial number of the device appears in the text box above the toolbar when the monitor is detected Figure 12 Tip If the Radon Sentinel is not automatically detected by the software click Refresh Devices On the software toolbar click Get Data to synchronize the data on the Radon Sentinel with the software 3 The software retrieves the data from the Radon Sentinel Figure 12 17 Company Information Radon Monitor Company Sun Nuclear Corporation Model Number 1030 Serial Number 72101001 Addressl 415 Pineda Court Calibration Factors 1 284 4286 Address2 2 265 5 288 Company 3 282 6 279 info mation City Melbourne r State Province FL hegre aaa alibration Date entered in zp 32940 Monitor Date and Time 3 19 2013 4 41 PM software and EE saved to License Number 123456789 d evice Personal Identification Number 1234 Data retrieved Test Summary from Radon Test 1 Test 2 7 Start Time 3 9 2013 2 04 P
20. About Radon The U S Environmental Protection Agency EPA maintains a comprehensive web site on radon at where you can find PDF and HTML ready versions of all of the EPA s documents brochures and publications relating to radon Below are descriptions of three of the more common EPA publications on radon copied from site A Citizen s Guide to Radon The guide to protecting yourself and your family from radon This resource offers strategies for testing your home for radon and discussions of what steps to take after you have tested as well as discussions about the risk of radon and radon myths EPA 402 kK 09 001 January 2009 Home Buyer s and Seller s Guide to Radon This booklet is intended for anyone who is buying or selling a home real estate and relocation professionals home inspectors and others EPA 402 K 09 002 January 2009 Consumer s Guide to Radon Reduction How to Reduce Radon Levels in Your Home This recently revised booklet is for people who have tested their home 32 for radon and confirmed that they have elevated radon levels This booklet can help you select a qualified contractor to reduce the radon levels in your home determine an appropriate radon reduction method and maintain your radon reduction system EPA 402 K 06 094 December 2006 33 This page is intentionally left blank 34 Index A AC adapter connecting 4 accessories 2 additional information application help 32 on the web 32
21. M Start Time mon Ito r Units pCi I Units Hours Delayed 24 hour s Hours Delayed Duration 24 hour s Duration Measurement Interval 1 hour s Measurement Interval Measurements 24 Measurements Overall Average 0 2 Overall Average EPA Average 0 2 EPA Average Get Data Refresh Devices x Continuous Radon Moni Device serial 721001 TEN 5 num b er B Open Save GetData 9 RefreshDevices Use Test 1ForReport UseTest2ForReport _ vj L Preview Raw Data L Preview Customer Repot PrintRawData Print Customer Repot Save PDF 3 Inspection Company Test 1 Customer Info Test 1 Chat Test 2 Customer Info Test 2 Chart Unsaved Data Figure 14 Continuous Radon Monitor Main Screen Displaying Test Summary Data The Test Summary panel displays a summary of downloaded data If two tests were in memory on the Radon Sentinel the software displays both sets The data cannot be edited however you can indicate the presence of a mitigation system and whether or not that system is working See Setting up Customer Information on page 19 1 2 Connect the Radon Sentinel to the computer and then start the Continuous Radon Monitor software If more than one device is connected select the device to work with from the drop down list above the toolbar and then click Get Data A summary of any downloaded tests appears in the Test Summary panel o
22. OO SME close Page XYZ Inspections Name l ann Address1 12 Mai Maximize window Address2 here City Somew Florida State Province Florida 334455 ZIP 334455 555 555 5555 Phone Number 555 Copy Billing Address To Site Address E Mitig Mitig Data opens in new window eens taht m Figure 18 Preview Report 23 Print Report 1 Download test data and save It or open a Saved file 2 On the toolbar if there are two reports open select the radio button for the test to print Use Test 1 For Customer Report or Use Test 2 For Customer Report 3 Configure the customer information and import photos if desired 4 Click Print Customer Report 5 Inthe Print dialog select the printer to use and configure printer properties if necessary 6 Click OK Save PDF To save report data with imported images save the report as a PDF 1 Download test data and save it or open a saved file 2 On the toolbar if there are two reports open select the radio button for the test to print Use Test 1 For Customer Report or Use Test 2 For Customer Report 3 Configure the customer information for the report 4 Click Save PDF 5 The PDF file opens in a new window Use the toolbar buttons or menu items to save or print the file 24 Specifications Model 1030 Radon Sentinel Specifications Table 2 Model 1030 Radon Sentinel Specifications Description Measurement Range Accuracy
23. a collected e Radon risk information e Any photos that were added on the Customer Info tab See Setting up Customer Information on page 19 The number of pages in the report will depend on the options configured for the report 1 Download test data and save It or open a saved file 2 On the toolbar if there are two reports open select the radio button for the test to be printed Use Test 1 For Customer Report or Use Test 2 For Customer Report 3 Configure the customer information and import photos if desired 4 Click Preview Customer Report The selected report opens in a new window Figure 18 The viewer s toolbar offers viewing options Maximize window View the window in full screen mode Zoom Increase or decrease the magnification of text Auto 500 200 150 100 75 50 25 10 Page layouts One page Two pages Three pages Four pages Six pages select the number of pages to fit in a single window Close Close the preview window Pages right side Scroll through the pages using the up down arrows 7x Continuous RADON Monitor rr T Select Test 1 or Test 2 data GFOpen Save GetData FF RefreshDevices L Preview RawData L Preview Customer Report Toolbar for viewing report Print RawData lt 3 Print Customer Report J Use Test 1 For Customer Report _ Use Test 2 For Customer Report x De eO a a af Print preview Billing Address O
24. ain screen provide access the panels for setting up company information customer information retrieving data and generating reports The toolbars at the top of the screen offer buttons for performing functions when working with data Figure 12 Device serial Toolbars number when multiple monitors are connected B Open Save BGetData LF RefreshDevices UseTest1ForReport UseTest2ForReport _ select a device 5 PreviewRawData L Preview Customer Repot Print Raw Data Print Customer Repot SavePDF f Y from the list Inspection Company Test 1 Customer Info Test 1 Chat Test 2 Customer Info Test 2 Chart T b Company Information Radon Monitor abs Company Sun Nuclear Corporation Model Number 1030 SerialNumber 72101001 Address1 415 Pineda Court Calibration Factors 1 2 84 Address2 2 2 65 3 282 Company information 7 eo p y State Province FL Battery Voltage 2 61 volts and PIN Calibration Date 5 18 2012 ZP 32940 Monitor Date and Time 3 19 2013 4 41 PM Phone 123 456 7890 License Number 123456789 Personal Identification Number 1234 Test Summary Test 1 Test 2 Start Time Start Time Units Units Hours Delayed Duration Duration Measurement Interval Measurement Interval Measurements Measurements Hours Delayed Overall Average Overall Average EPA Average EPA Average Figure 12 Main Screen Inspection View Configur
25. aph line in units selected for test Rel Humidity Displays relative percent humidity graph line The parameters selected on the Radon Sentinel pCi l or Bg m3 determines the units used for temperature pressure and humidty 20 Saving a Test Data retrieved from the monitor can be saved to a txt file Note that if two tests are retrieved data for both tests are saved in the same txt file 1 Retrieve data from the monitor See Retrieving Data from the Monitor on page 17 2 On the toolbar click Save 3 When the Select Folder and Filename window opens browse to the directory where the file will be saved enter a file name or accept the default and then click Save e By default the software creates a folder for saved data in My Documents Completed Tests e f a billing address was entered for the test the file name will default to lt Address1 gt _mmddyyyy txt For example if 723 Main St is entered in the Address field for the billing address for a report and the report is saved on 72 75 2077 the report name defaults to 723 Main St_12152011 e After test data is saved the status bar at the bottom of the Continuous Radon Monitor window displays the name of the saved file Open a Saved File Note Saved files can only be opened using the same date and time formats that were in use when the data was saved For example lt P When the data was saved ifthe date format was set to mm dd yyyy and the time format
26. ay shorten battery life Connect the AC humidity The battery compartment is accessed from the right side panel of the Radon Sentinel Figure 2 Replacement batteries can be purchased from any retail SOUICE Remove cap turn CCW Unit uses four size C alkaline batteries two in each compartment Figure 2 Inserting Batteries 1 Remove the cap from one of the battery compartments by rotating it counterclockwise 2 Insert two size C alkaline batteries so that the negative end of the battery goes Into the compartment first Figure 2 3 Replace the battery compartment cap by pressing down on the cap while turning it clockwise until it Is tight Tip Use two hands hold cap down with your thumb and use your other hand to tighten the cap If cap is cross threaded remove it and realign threads 4 Repeat steps 1 through 3 for the other battery compartment Connecting the AC Adapter Use these instructions when using AC power for the primary power source and the batteries as backup 1 Connect USB cable type A connector to USB port on AC adapter Figure 3 Figure 3 Connecting Power to the Radon Sentinel Type A connector oe USB indicator illuminates USB port on pa when USB cable is AC adapter in A connected to PC mi 2 Plug USB cable type B connection into USB port on right side panel of Radon Sentinel 3 Plug AC adapter into a 120 240 VAC 50 60 Hz wall outlet Turning on the Display
27. cept the terms of the license agreement the license agreement is o not accept the terms of the license agreement v Ne Figure 10 End User License Agreement Windows XP Follow the on screen instructions to complete the software installation accepting the default folders and file locations When the SNC Driver Installer window opens click Next The device drivers are installed and then the driver status Ready to use displays in the system tray Note wo device drivers will be installed so the SNC Driver Installer may run twice 8 When the drivers are installed the SNC Driver Installer window displays the drivers that were installed Click Finish 9 The Radon Monitor InstallShield Wizard window displays Click Finish to exit the wizard then remove the CD 12 Installing on Windows 7 Operating System When installing the Radon Monitor software on a computer running the Windows 7 operating system It must be installed using the Run as administrator option 1 Accept the terms of the license ag reement D do not accept the terms of the license agreement 7 Connect the Radon Sentinel to the computer then insert the CD in the CD drive When the autoplay window opens click Decline to close the window that warns that the program Is protected by copyright law Navigate to the following directory on the CD FsCommand Radon Software 1030 Right click on Radon1030 exe and select Ru
28. con Windows 7 system tray icon Safely Remove USB Mass Storage ri Safely Remove Hardware and Device Eject Device Figure 8 System Tray Icons Safely Remove Hardware 10 Radon Monitor Software About the Software The Continuous Radon Monitor software can be used to e Enter parameters and transfer those parameters to the Radon Sentinel e Transfer report data from the Radon Sentinel to the computer e Add customer information and test conditions to a report e Print reports on any available printer Recommended System Requirements To view the recommended system requirements for the software see Radon Software Recommended System Requirements on page 26 Installing Software Use the installation instructions for the type of operating system that is running on your computer Windows XP or Windows 7 The user logged in to the computer must have administrative rights to perform the Installation Note The Radon Sentinel device drivers are installed automatically as part of the software installation Installing on Windows XP Operating System 1 Connect the Radon Sentinel to the computer then insert the CD in the CD drive 2 When the install menu opens select the Software link below the 1030 Radon Monitor section SUN NUCLEAR corporation CD Ver 3 00 00 1030 Radon Monitor Software link for 1028 1029 Radon Monitor 1027 Radon Monitor Figure 9 Radon Monitor Installation Menu 11 1030 Radon Monito
29. e until complete if AC power is reliable See nserting Batteries on page 3 Shutting down The system shuts down to save power No Extern Power AC power should be connected to continue the test At the conclusion of the test replace the battery Use the instructions below to replace the batteries 1 Ifa testisin progress connect the AC power adapter or wait for the test to complete 2 Open battery compartments on right side panel and remove batteries 3 Insert four fresh size C alkaline batteries See nserting Batteries on page 3 Connecting Radon Sentinel to Computer Connect the Radon Sentinel to a computer using the USB cable furnished with the device Multiple radon monitors may be connected simultaneously using the available USB ports on the computer or using an external USB hub 1 Connect the USB type A connector Figure 7 to the computer or USB hub 2 Connect the USB type B connector to the Radon Sentinel Type A connector to computer Figure 7 USB Connectors Note f using multiple Radon Sentinels the Device Driver Installation Wizard will run when each device Is initially connected to the computer Accept the defaults for the installation The device is ready to use when Ready to use appears in the system tray Disconnecting the Radon Sentinel From the system tray click the icon Figure 8 to safely remove hardware and then click on the Radon Sentinel device Windows XP system tray i
30. ensor Out of Range Humidity Sensor Out of Range SPI Port Error Dead Channel Memory Error Test Interval Aloha Count Overflow Test Hourly Alpha Count Overflow High Voltage Out of Range Interboard comm error Radon System Error Codes An error message will appear on the Radon Sentinel display if the device experiences an unusual system error Normally this indicates a hardware or firmware failure Make a note of the 8 digit error code and then contact Sun Nuclear Customer Support for assistance See Contacting Sun Nuclear Support on page 30 Contacting Sun Nuclear Support You may request support in two ways e Use our online form See Radon Support Web Page below e Contact the Sun Nuclear Support team by telephone 1 321 259 6862 Radon Support Web Page The Sun Nuclear Support web page for Radon devices offers online support 24 hours a day 7 days a week The Radon Support web site can be used to e Submit service requests for calibration and repair online e Pay for calibration and repair online e Access a comprehensive list of frequently asked questions e View video tutorials for many common inquiries 30 Regulatory Supplement Conventions e Bold typeface indicates a button name or an entry that the user must type e talicized typeface indicates the title of a manual or introduces a new term or ohrase e Bold italicized typeface indicates a menu option e Text in double quotes indicates a message that
31. igation system was working select the check box associated with Mitigation System Working 3 Toadd photo s a Enter an optional caption in the Picture Caption text box Note that the first Image imported will appear on the cover page of the report b Click the browse button and navigate to the location of the photo c Select a photo and click Open Photos cannot be deleted or edited however they can be excluded from a report by clicking the thumbnail of the photo click again to include Tip Photos are not saved with raw data so to remove unwanted photos save close reopen the saved file and then add the desired photos 4 f two tests were downloaded click the Test 2 Customer Info tab and then repeat steps 1 through 3 for the second test rao x 72101001 Help Open Save GetData F Refresh Devices Use Test 1 For Report O Use Test 2 For Report m Transfer billing information to L Preview Raw Data L Preview Customer Report Print Raw Data Print Customer Reg rt Save PDI Inspection Site Address bpection Company Test 1 Customer Info Test 1 Chat Test 2 Customer Info TAAt 2 Chart Test 1 Customer Billing Address Inspgftion Site Address Customer Info Name John Smith Name John Smith Addressl 123 Main St Addressl 123 Main St Address2 Address2 city Any City City Any City State Province Any State staterProvince Any State INdicate If a mitigation system
32. ing Company Information The nspection Company tab is used to enter or maintain details about an inspection company Upon initial use of a Model 1030 Radon Sentinel this tab is used to configure information such as the name of the inspection company address phone number etc The information entered on this screen is uploaded to the Radon Sentinel and is used in reports Note The only data required on the Company Information panel is the Personal Identification Number PIN By default the PIN is set to 1111 The company name address telephone number and license number are optional however if this information is not entered reports that are generated using the Continuous Radon Monitor software will not display the company information 1 Connect the Radon Sentinel to the computer and then start the Continuous Radon Monitor software 2 f more than one device is connected select the device to work with from the drop down list above the toolbar 3 Enter the company name address telephone number and license number 15 The following characters can be used when configuring company information with the exception of the Personal Identification Number space amp 0123456789 lt gt _ Upper and lower case alpha characters A Z a z Note We recommend entering a Personal Identification Number PIN to protect the data from interference by parties other than the radon tester If the default PIN 1111
33. is accessed e EPA average or current value is requested during a measurement e The memory is cleared When a PIN is requested if it is not entered within 10 seconds the display clears during a measurement the Radon Sentinel returns to measurement mode If an incorrect PIN is entered the messages Do Not lamper and Illegal will appear Note When the PIN is requested and entered the Radon Sentinel remains unlocked for 3 minutes Positioning the Monitor 1 Place the Radon Sentinel in the desired position F in the area to be monitored for radon gas The device does not need to be level 2 o usea tripod thread the standard tripod screw 1 4 20UNC into threaded fitting on the bottom of the case Checking Unit Status Figure 6 Using a Tripod Before starting a test it is a good practice to scroll through the parameters to ensure that they are correct 1 Press any key to power on the display 2 Press Status 2 3 Theitems in the status menu scroll automatically or you can press Status 2 to scroll manually These status items can be displayed during a test by pressing any button and then pressing Status 2 To change the parameters see Configuring Parameters on page 6 Starting a Test 1 When Ready to Jest appears on the display press Start Stop 1 to start a test 2 Starting Test appears on the display followed by the settings defined for the test Memory One Memory is chec
34. is used changes can be made to settings on the Radon Sentinel without entering a PIN 4 fdesired change the Personal Identification Number The PIN must consist of four digits using any combination of the numbers 1 through 6 5 After entering data click Save to Device to initiate the data transfer to the Radon Sentinel e f invalid characters are entered for the PIN an error message appears Stating that the Personal Identification Number did not save to the device e Click OK to close the error message enter a four digit PIN using only the numbers 1 through 6 and then click Save to Device Editing Company Information 1 Connect the Radon Sentinel to the computer and start the Continuous Radon Monitor software 2 f more than one device is connected select the device to work with from the drop down list above the toolbar and then click Get Data 3 Make any necessary changes and then click Save to Device to transfer the data to the Radon Sentinel Radon Monitor Details The nspection Company tab displays details about the Radon Sentinel model number serial number calibration factors determined during factory calibration battery voltage calibration date and the date and time from the Radon Sentinel This view can also be used to synchronize the date and time from the computer with the Radon Sentinel The data in this panel cannot be edited 1 Connect the Radon Sentinel to the computer and start the Continuous Radon
35. ked If data is found memory must be cleared See Clearing Memory on page 9 Delay hours Displays the time delay defined in the setup Note that the time shown for the customer report will be the time the actual measurement begins Interval hours Displays the measurement interval defined in setup Duration hours Displays the test duration defined in setup Testing hours The test has started and will be finished after the specified duration plus any delay The display turns off after a few minutes and remains off unless the test is terminated or the display is turned on Terminating a Test To terminate a test in progress 1 Press Start Stop 1 2 he prompt Enter PIN displays Use the number keys on the unit to enter the PIN End lest Y 1 N 2 displays Press 1 to end the test A Ww Confirm Y 1 N 2 displays Press 1 to confirm Ending Test displays briefly followed by Ready to Jest or if both memory slots are full Memory Full displays see Clearing Memory on page 9 Displaying EPA Average and Current Radon Values The EPA AVG average and CUR current radon values can be displayed on the Radon Sentinel during a test or after a test is completed if the test data has not been cleared 1 Press any button to turn on the display 2 Press EPA AVG CUR 4 to view the EPA value that is the average radon concentration with the first four hours of measurement removed
36. llows two way communication with PC 110 240 VAC 50 60 Hz converted to 5 VDC 500 mA USB Power Supply Battery Power Backup connection power adapter Four size C alkaline non rechargeable batteries supply 300 hours of operation when AC power is not connected Standard 1 4 20 UNC threaded fitting on bottom of case Tripod threaded fitting Handle Integrated handle for carrying or for use with cable lock Weight Dimensions 3 75 Ibs 1 7 kg 5 5 W x 9 6 H x 4 4 D inches 139 7 x 243 84 x 111 76 mm 25 Radon Software Recommended System Requirements Table 3 Radon Sentinel Software Specifications Characteristic Recommendation Operating system Windows XP or Windows 7 any edition 32 or 64 bit Computer hardware Hard disk space 850 MB CPU speed 1 6 MHz Total physical memory RAM 512 MB Video card 1024 x 768 32 bit color depth USB version 1 USB v2 0 port minimum PDI 2 0 driver version Requires version as of date of this document 2 08 08 Microsoft NET Version 4 0 Framework Service Maintaining Hardware Parts and Repairs Order accessories and replacement parts from Sun Nuclear Sales For part numbers see Farts on page 1 For accessory part numbers see Options and Accessories on page 2 There are no user serviceable parts inside the Radon Sentinel If there are problems with the device please contact Sun Nuclear Customer Support See Contacting Sun Nuclear Support on page 30 Storage
37. measurement Sentinel STATUS scroll through status settings press repeatedly to scroll more quickly SETUP Enter Setup mode to enter values START STOP using keypad CURR displays the measured short term ine radon gas concentration the current rolling average of the most recent 12 hours CLEAR EPA displays measured cumulative pd STATUS average radon gas concentration in pCi l or Bq m in the most recent test except the E first 4 hours of data from the average SETUP z AVG displays the measured cumulative average radon gas concentration in pCi l or lt A Bq m in the most recently measured test EPA AVG CUR Arrow keys 4 5 press to alter a selection then press SETUP to save TEMP PRESS HUMID e Right arrow 5 scrolls forward e Left arrow 4 scrolls backward 4 C CELL BAT CLEAR clears the test memory TEMP displays temperature pe PRESS displays pressure measurement SUN NUCLEAR HUMID displays relative humidity i aca Figure 5 Controls Configuring Parameters Note Changes to parameters affect future tests only Measurements taken prior to the change will not be affected General parameters for the Radon Sentinel can be configured using a computer A limited set of parameters can be entered using the keys on the device see Set Parameters using Radon Sentinel Keys on page 6 For instructions to enter company information using a computer see Configuring Compan
38. n the nspection Company tab Start Time Date and time the test started The time shown will be the time the actual measurement begins Units The units selected for the test pCi l or Ba ms Hours Delayed Number of hours if any that the start of the test was delayed Duration Length of the test in hours Measurement Length of time between consecutive measurements Interval Measurements The number of measurements taken during the test Overall Average The average of radon concentration over the entire test EPA Average The radon concentration average less the first 4 hours of data 18 Setting up Customer Information Details such as a customer s name and billing site information for a test are entered using the est 7 or Test 2 Customer Info tabs This information is included on the customer report 1 After downloading test data click the Test 1 Customer Info tab Two panels display Figure 15 Inthe Customer Billing Address panel enter the name address and ohone number to which the test will be billed e f the inspection site address is the same as the billing address click the double arrow between the panels to copy Customer Billing Address information to nspection Site Address panel Otherwise complete the Inspection Site Address panel with the information for the site tested 2 Ifaradon mitigation system was installed at test site select the check box associated with Mitigation System Exists If a radon mit
39. n as administrator The Radon Monitor InstallShield Wizard starts and checks for the presence of Microsoft NET Framework 4 0 on the computer e f Microsoft NET Framework is present on the computer continue to step 4 e f itis not found a screen opens prompting for the installation Click Install If prompted to reboot the computer when the Microsoft NET Framework installation completes click YES The software installation will continue when the computer Is restarted amp Note Microsoft NET Framework must be installed for the Continuous Radon Monitor software installation to continue The Radon Monitor InstallShield Wizard welcome screen opens Click Next The License Agreement screen displays Figure 11 Read and accept the terms of the license agreement and click Next Radon Monitor InstallShield Wizard License Agreement Please read the following license agreement carefully Sun Nuclear Corporation END USER LICENSE AGREEMENT this Agreement This Agreement is a legal agreement between you the Licensee and Sun Nuclear Corporation SNC for the Sun Nuclear software that accompanies this Agreement If you agree to be bound by the terms of this Agreement accept the license agreement at which time the software will be downloaded and or installed and you will be granted a license to use the software Tf wan da not scree ta the terms af this Acraement dn nat acce
40. ng the up down arrows Figure 17 Previewing Raw Data Print Raw Data Raw test data that has been downloaded and saved can be printed to a local printer or a network printer 1 2 3 Download test data and save it see Saving a Jest on page 21 or open a saved file see Open a Saved File on page 21 On the toolbar click Print Raw Data The Print dialog opens with your default printer selected Configure printer properties if necessary and click OK Customer Reports Data that has been downloaded and saved is used in the customer report and can be used to create a PDF of the customer report Preview Report The Preview Customer Report option opens a window so you can view the report before printing it Data from the Radon Sentinel must be saved before previewing the report A report contains the following elements Cover page image if specified in the Customer Information tab See Setting up Customer Information on page 19 Customer and site information if configured See Setting up Customer Information on page 19 22 e Inspection company information See Setting up Customer Information on page 19 e Information identifying the device used for the test model serial number calibration date calibration factors start time for the test units specified for the test delay duration measurement interval number of measurements the overall average and the EPA average e A chart of the dat
41. nt the accept the terms of the license agreement Figure 11 End User License Agreement Window 7 Follow the on screen instructions to complete the software installation accepting the default folders and file locations 8 When the SNC Driver Installer window opens click Next 13 e A Windows Security prompt may appear asking for confirmation to install the CDM Driver Package this prompt will appear twice because two drivers will be installed Click Install e The device drivers are installed and then the driver status Ready to use displays in the system tray Note wo device drivers will be installed so the SNC Driver Installer may run twice 9 When the drivers are installed the SNC Driver Installer window displays the drivers that were installed Click Finish 10 The Radon Monitor InstallShield Wizard window displays Click Finish to exit then remove the CD Launching the Software Launch the software application by double clicking the Radon Monitor desktop shortcut or by selecting Start gt All Programs gt Sun Nuclear gt Radon Monitor he Radon Sentinel does not have to be connected when the software is launched For details about the software see Software Setup on page 15 Closing the Software To close the Continuous Radon Monitor software click the Close button EJ in the top right corner of the window 14 Software Setup Tabs on the m
42. r The Radon Monitor InstallShield Wizard starts and checks for the presence of Microsoft NET Framework 4 0 on the computer e f Microsoft NET Framework is present on the computer continue to step 4 e f itis not found a screen opens prompting for the installation Click Install If prompted to reboot the computer when the Microsoft NET Framework installation completes click YES The software installation will continue when the computer Is restarted Note Microsoft NET Framework must be installed for the Continuous Radon Monitor software installation to continue The Radon Monitor InstallShield Wizard welcome screen opens Click Next The License Agreement screen displays Figure 10 Read and accept the terms of the license agreement and click Next Radon Monitor InstallShield Wizard License Agreement Please read the following license agreement carefully Sun Nuclear Corporation END USER LICENSE AGREEMENT this Agreement This Agreement is a legal agreement between you the Licensee and Sun Nuclear Corporation SNC for the Sun Nuclear software that accompanies this Agreement If you agree to be bound by the terms of this Agreement accept the license agreement at which time the software will be downloaded and or installed and you will be granted a license to use the enfuyrare TPFrrrnn da nnt acres tn the terme of thic Acreament do nnt accent the Accept th e terms of ac
43. side back cover of the User s Guide The manufacturer s recommended calibration frequency for the model 1030 Radon Sentinel is one year See your state or Proficiency listings for requirements 28 Troubleshooting Table 4 Model 1030 Radon Sentinel Troubleshooting Indication Probable Cause Recommended Action Unit will not turn Power not connected and batteries are Connect power and or insert on missing or discharged four fully charged size C alkaline batteries Unit will not turn Internal short or disconnection Contact Sun Nuclear on with power Customer Support Unit will connected or good need to be returned batteries System error Radon monitor experienced an See Radon System Error message abnormal condition Codes on page 29 Radon Sentinel Radon monitor not detected by the Click Refresh Devices The serial number not software serial number displays when displayed in the connection is detected software Display shows Test interrupted before being Print results and count Motion Detected completed Motion occurred as test number of measurements If but motion not was terminated less than expected test recorded on report terminated prematurely Rerun test Software error Error messages display when starting Contact Sun Nuclear message the Continuous Radon Monitor Customer Support See application or when retrieving data Contacting Sun Nuclear from the Radon monitor Support on page 30 Humidity Sensor Error 1 Pressure S
44. turer s warranty applies the following items are specifically excluded from this warranty photomultiplier Geiger Mueller and proportional tubes batteries ancillary devices including but not limited to printers computers display devices etc and other components as may be specified in this manual 2 Calibration a b This instrument is warranted to be within its specified accuracy at the time of shipment If a question arises and SUN NUCLEAR CORPORATION determines that the initial calibration is in error the instrument will be re calibrated by SUN NUCLEAR CORPORATION at no charge SUN NUCLEAR CORPORATION is not responsible for calibrations performed by independent laboratories nor any calibration fees incurred prior to or subsequent to SUN NUCLEAR CORPORATION warranty service The return policy is as stated in 1 c above 3 Non warranty Service a Repairs and or replacements not covered by this warranty may be performed by SUN NUCLEAR CORPORATION or a factory authorized service location Estimates of repair charges may be requested however a charge for estimate preparation may apply if the repair is later not authorized by the customer The cost of transportation into and out of the service location will be the respon sibility of the customer The instrument should be shipped to
45. y Information on page 15 Set Parameters using Radon Sentinel Keys Options for the following parameters can be changed using the keys on the device DELAY Select the time delay for starting a test 0 12 24 48 hours INTERVAL Select measurement interval 0 5 1 2 4 8 12 16 20 24 hours DURATION Select duration of the test 1 12 24 36 48 60 72 84 96 100 999 hours UNITS Select the units for the test pC I picocuries per liter or Bq m3 becquerels per cubic meter PINNUM Set to any combination of four digits using the numbers 1 through 6 default setting is 1111 When the PIN is set to 1111 the Radon Sentinel does not prompt for a PIN Use the following procedure to change the parameters 1 Press any key to turn on the unit Press Setup 3 3 If prompted enter the PIN Setup Menu displays 4 Press Setup 3 to scroll to the parameter to change 5 When the parameter is displayed press lt 4 or 5 to select the desired setting Exception When setting the PIN use the keys labeled 1 through 6 to enter a 4 digit PIN 6 Press Setup 3 to save and advance to the next parameter 7 Repeat steps 4 through 6 until the parameters are defined and Setup Menu Done displays The new parameters will apply to future tests Personal Identification Number The prompt for entering the PIN appears when e The Radon Sentinel is turned on e A testis started e lt Atest is stopped e The setup
46. ze the chart display 4 00PM 6 00PM 8 00PM 10 00PM 12 00 AM 2 00AM 4 00AM 6 00AM 8 00AM 10 00 AM 12 00 PM ZIOP v Radon pCi v Motion Errors V Action Level 4 pCi I Temp F Press inHg Vs Rel Humidity Unsaved Data Figure 16 Test 1 Chart Example e Left scale indicates the Radon concentration in the units selected for the test pCi l or Ba ms e Right scale shows temperature in C or F pressure inHg or kPa and percent relative humidity depending on the units selected for the test e Horizontal scale shows date and time range for the test If test duration was one day or less scale shows hourly increments e Check boxes below the chart can be used to select the components that are visible in the chart Radon lt pCi l or Ba m3 gt Displays periodic radon measurements graph line Motion Errors Displays vertical motion error lines motion errors occur when device is moved during the test Action Level lt nn pCl or Displays a horizontal line indicating the point at which Bq m3 gt radon test passes or fails defaults to 4 pCi l or 148 Bq m3 If the average is above the red line the test fails if it is below the line the test passes If the default setting does not match the regulatory level in your jurisdiction deselect the checkbox to hide it Temperature lt C or F gt Displays temperature graph line in units selected for test Press lt units gt Displays pressure gr
Download Pdf Manuals
Related Search