Home

User's manual Hydra Compact Twin

Contents

1. Figure 4 2 Hardware configuration for redundant operation with DVI DVI output card with one output card per section Barco Hydra Compact Twin R59770027 Revision 13 February 2007 4 6 4 Operating 4 4 Dual mode In dual mode one HYDRA COMPACT Twin section is connected to two projection modules A special setting of the iSrupio software allows displaying the sources of the HYDRA COMPACT Twin section on both modules please refer also to the iSrupio user s manual section Dual Mode If using a DVI DVI output card then one card per section is sufficient to setup dual mode If using a DVI video output card then a second additional DVI video output card is required for dual mode DVI video output card Two output cards are required Each output card is connected to one projection module The first output card the one Which is next to the input cards must be connected to the left projection module the second output card must be connected to the right projection module Dual mode can be established via the DVI connectors or the BNC connectors The figure below demonstrates the cabling in dual mode Display section 1 Hydra Compact Twin SBC OVL IPU OPU JSBC OVL IPU OPU Section 1 Section 2 Figure 4 3 Dual mode connection for tw
2. Hydra Compact Twin Hydra Compact Twin OI OI N OJ IOJ OJ IO U OJ IOJ U O L O SBC OVL IPU OPU SBC OVL IPU OPU SBC OVL IPU OPU SBC OVL IPU OPU Section 1 Section 2 Section 1 Section 2 Figure 4 1 Hardware configuration for redundant operation with DVI video output card DVI output mode with two output cards per section left and video output mode with one output card per section left Barco Hydra Compact Twin R59770027 Revision 13 February 2007 4 5 4 Operating Analog or Digital Output with DVI DVI Output Card If the HYDRA COMPACT TWIN sections are equipped with DVI DVI output cards one output card per HYDRA COMPACT TWIN section is sufficient The upper connector 1 on the output card is used to connect to the projection module the lower one 2 is used to connect to the overlay input card of another HYDRA COMPACT TWIN section and vice versa Display section 1 Display section 2 Hydra Compact Twin F l l NAO SBC OVL IPU OPUJSBC OVL IPU OPU Section 1 Section 2
3. Hydra boot CD R32875211 in the drive and close it e Switch off the HYDRA COMPACT TWIN with the power switch 5 e Switch it on again If the iSrupio Hydra boot CD R32875211 is already in the CD ROM drive then just e Press the power switch 5 on the front of HYDRA COMPACT TWIN e Check the state of the green LED power 7 on the front of HYDRA COMPACT TWIN It must be permanently on to indicate that the power supply operates properly If this is not the case see section 7 1 Hydra Compact Twin does not start up please Now the HYDRA COMPACT TWIN starts booting from the iSrupio Hydra boot CD The startup screen is displayed By default it shows the Barco logo together with the IP address of the HYDRA COMPACT TWIN which is displayed in the upper left corner If the HYDRA COMPACT TWIN already has been configured also another startup screen could ap pear dependent on the configuration of the startup layout As soon as the start screen is displayed the HYDRA COMPACT TWIN is ready for operation and a connection from an operator PC to the HYDRA COMPACT TWIN can be estab lished This and any further operation is explained in detail in the iSrupio user s manual 150 158 183 146 version 1 8 4 BARCO Visibly yours Projector Barco Marylou Figure 3 20 HYDRA COMPACT TWIN startup screen 3 3 3 Switching off If the HYDRA COMPACT TWIN was operated with the iSrupio software it must be halted before it can be switched off Therefore u
4. 10 AINR 3 11 AINL 4 12 AINR 4 13 AINL 5 14 AINR 5 15 AINL 6 16 AINR 6 17 GND 18 GND 19 AINL 7 20 AINR 7 21 AINL 8 22 AINR 8 23 AINL 9 24 AINR 9 25 AINL 10 26 AINR 10 27 AINL411 28 AINR 11 29 AINL 12 30 AINR 12 31 AINL 13 32 AINR 13 33 GND 34 GND Barco Hydra Compact Twin R59770027 Revision 13 February 2007 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 GND GND AINL 0 AINR 0 AINL 1 AINR 1 AINL 2 AINR 2 AINL 3 AINR 3 AINL 4 AINR 4 AINL 5 AINR 5 AINL 6 AINR 6 GND GND AINL 7 AINR 7 AINL 8 AINR 8 AINL 9 AINR 9 AINL 10 AINR 10 AINL 11 AINR 11 AINL 12 AINR 12 AINL 13 AINR 13 GND GND 6 Technical appendix Figure 6 12 SCSI4 female connector analog audio daughter board pin assignment 6 12 Digital Audio Daughter Board O O CN UU a WN WW UU VU N N NNN N N N N N mi mi mi mi mi Su Uu si GG 0 N AU a WUN sd GD GEOM AO LVI kk YN Barco Hydra Compact Twin R59770027 Revision 13 February 2007 GND GND DIN 0 not connected DIN 1 not connected DIN 2 not connected DIN 3 not connected DIN 4 not connected DIN 5 not connected DIN 6 not connected GND GND DIN 7 not connected DIN 8 not connected DIN 9 not connected DIN 10 not connected DIN 11 not connected DIN 12 not connected DIN 13 not connected GND GND 35 36 37 38 39 40 41
5. 61 Technical datassa id tale 6 2 MA ase do ue Maman 6 7 6 3 O UE O ES 8 ne e LL 6 15 A A RO 7 1 7 1 Hydra Compact Twin does not start Up iii 7 2 TOM a ia 7 2 MAA 8 1 SAM e lean e o ale 8 1 8 2 USO edo dede ue ee Me e a 8 1 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 vi 1 Introduction 1 Introduction This chapter explains the structure of the manual itself and the used typographic styles and symbols Safety in formation is provided concerning the operation of computer systems from Barco Barco Hydra Compact Twin R59770027 Revision 13 February 2007 1 1 1 Introduction 1 1 How this manual is organized This manual describes the design of HYDRA Compact TWIN from Barco It is divided into eight chapters Introduction explains the structure of the manual itself and the used typographic styles and symbols Safety information is provided concerning the operation of computer systems from Barco Summary gives an overview about the features of HYDRA COMPACT TWIN Getting Started describes the set up of HYDRA COMPACT TWIN If your HYDRA COMPACT TWIN is already configured within your work ing place you can skip this chapter and continue with chapter 4 Operating operating provides information about extended configurations functionality and access to the settings of the HYDRA COMPACT TWIN Maintenance describes the maintenance of HYDRA COMPACT TWIN Technical Appendix
6. Figure 3 5 Ports of single board computer 2 and corresponding slot plate To connect a section of the HYDRA COMPACT Twin to the Ethernet connector 4 a 100Base T cable with twisted transmitter and receiver pairs must be used Besides a PS 2 keyboard mouse connector 6 and VGA connector 2 both not used during standard opera tion of the HYDRA COMPACT TWIN there is a standard serial port connector 1 Order In section 1 the single board computer is inserted to the left in the first slot of a section with the serial port slot plate is covering the next slot on its right In section 2 the serial port slot plate is in the first slot followed by the single board computer counted from left to right if looking to the back of the HYDRA COMPACT TWIN In case that only one section shall be equipped this has to be the section 1 on the left hand ce side Section 2 may remain unequipped Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 7 3 Getting started 3 2 3 Overlay Input Card The overlay input card has an input connector that can be used to integrate digital graphical data with the data from the SBC Input can be any graphical data with the appropriate timing and resolution In particular the over lay input card can be used to configure the system for redundant operation please see section 4 3 Redundant operation Connectors The overlay input card provides a DVI I connector to insert digital da
7. dus VBrick VideoLAN Vorx MPEG 4 part 2 Cornet DVTeL IndigoVision Lanaccess Mavix NiceVi sion Siemens OTN Teleste VBrick Verint VideoLAN Vorx MPEG 4 h263 Bosch PelcoNET MJPEG AXIS Lenel VideoLAN MXPEG Mobotix 2D Wavelet Visiowave TRANSFORM SCN Barco Table 6 5 Streaming video card technical data Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 4 6 Technical appendix RGB Input Card socket RGB input 2xDVI I FBS P29 horizontal frequency 15 kHz 90 kHz pixelclock analog interface 20 MHz 140 MHz digital interface 20 MHz 112 MHz resolution amp colors analog VGA 60 Hz 24 bpp SXGA 75 Hz 24 bpp sync modes separate sync composite sync sync on green resolution amp colors analog HD 24 bpp only progressive scan 720x483 60 1 001 Hz 1280x720 60 1 001 Hz 60 Hz 1920x1080 24 1 001 Hz 24 Hz 25 1 001 Hz 25 Hz 30 1 001 Hz 30 Hz sync modes American Bi level American Tri level resolution amp colors digital with input signal along DVI specifications 640x480 60 Hz 24 bpp 800x600 60 Hz 24 bpp 1024x768 60 Hz 24 bpp 1280x1024 60 Hz 24 bpp Table 6 6 RGB input card technical data Overlay Input Card OVL IPU 4 socket graphics input DVI I connector genlock LTC VITC input D15 timing from VGA 60 Hz up to UXGA 60 Hz pixelclock 25MHz up to 165MHz Table 6 7 Overlay input card OVL IPU 4 technical data Output card DVI video 1 channel digi
8. Barco Hydra Compact Twin R59770027 Revision 13 February 2007 green or yellow green Earth Ground blue or white Neutral brown or black Line Live Figure 1 2 NEMA 5 15 plug Do not allow anything to rest on the power cords Do not locate this product where people will walk on the cords To disconnect the cords pull them out by the plug Never pull the cords themselves If an extension cord is used with this product make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock Never spill liquid of any kind on the product Should any liquid or solid object fall into the cabinet unplug the set and have it checked by qualified service personnel before resuming operations Lightning For extra protection for this video product during a lightning storm or when it is lift unattended and unused for a long period of time unplug it from the wall outlet This will prevent damage to the unit due to lightning and AC power line surges 1 Introduction 1 3 3 Unpacking of devices Note advises on the packaging for unpacking 1 3 4 Installation e Do not place this unit on an unstable cart stand or table The unit may fall causing serious damage to it e Do not use
9. CD ROM drive to view the manual If autorun is enabled on the computer the start page of the CD comes up automatically Else open the start page index html of the CD manually On this start page you will find a link to the user s manual of HYDRA COMPACT TWIN Acrobat Reader can be used to view the file Adobe Acrobat Reader is free and freely distributable software that lets you view and print Adobe Portable Document Format PDF files If Acrobat Reader is already installed the manual can be viewed just by a dick on the respective link Else the Acrobat Reader must be installed first The required installation files can also be found on the CD Barco Hydra Compact Twin R59770027 Revision 13 February 2007 1 7 2 Summary 2 Summary This chapter gives an overview about the features of HYDRA COMPACT TWIN Barco Hydra Compact Twin R59770027 Revision 13 February 2007 2 1 2 Summary 2 1 Properties iSrupio is a complete video audio and data monitoring system It typically consists of one or more HYDRA control lers a visualization system usually a rear projection Display Wall and the iStupio software to manage the com plete system One of the possible HYDRA controllers is the HYDRA COMPACT TWIN The Hydra concept A HYDRA device is the hardware part of the iSrupio system Different video signals analog SDI or HD SDI RGB data can be connected to a Hypra device by means of its Streaming video cards SDI
10. Figure 6 11 Breakout Cable for overlay input card OVL IPU 4 pin ASSIGNMENT eeesesesseeceeeeeeeeeeeeeeeseseeeeeeees 6 11 Figure 6 12 SCSI4 female connector analog audio daughter board pin assignMent iiii 6 12 Figure 6 13 SCSI4 female connector digital audio daughter board pin assignmMent 6 13 Figure 6 14 Analog EDAC connector pin assignment oooocococococococononanncnonononononnnnnonononononononnnnonononon on aaa la In ln laln 6 14 Figure 6 15 Digital EDAC connector pin assiQNMEent 6 14 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 8 2
11. Revision 13 February 2007 3 14 3 Getting started 3 2 6 Output Card The HYDRA COMPACT Twin supports different types of output cards Current models are the DVI DVI digital output cards with scaling the DVI DVI digital analog output cards the DVI DVI digital output cards and the DVI video output cards DVI DVI digital output card with scaling The DVI DVI digital output card with scaling provides the facility to connect two projection modules or monitors for the graphical output of the HYDRA COMPACT TWIN The output data is provided for digital connection The card allows additionally scaling of the output The front plate is labeled with OPU DD Connectors On the DVI DVI digital output card with scaling there are two DVI I connectors 4 1 DVI I connector for digital output channel 1 2 DVI I connector for digital output channel 2 3 green LED output channel 1 lightens up once after successful boot process 4 green LED output channel 2 lightens up once after successful boot process Figure 3 12 Connectors of DVI DVI digital output card with scaling Dual mode To use dual mode the second output channel is used for a second display device Please refer to section 4 4 Dual mode for the appropriate cabling Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 15 3 Getting started DVI DVI digital analog output card The DVI DVI digital analog output card provides the facility to connect two projection mo
12. The table below lists the names and functionality of the LED s at the front of HYDRA COMPACT TWIN number 7 green 8 green 9 red 10 green 11 red 12 green 13 red name meaning power power failure A1 OVL power OK B1 power unit A2 section 1 software heartbeat B2 section 1 system error A3 section 2 software heartbeat B3 section 2 system error state ON permanent ON blinking and Buzzer is active OFF ON permanent OFF ON permanent ON blinking and Buzzer is active ON blinking OFF ON blinking OFF ON blinking OFF ON blinking OFF meaning power supply and power modules OK one or more power modules failed one or more power cords are disconnected the device is off 3 3 V on the overlay board is OK 3 3 V on the overlay board has failed power supply and power modules OK one or more power modules failed one or more power cords are disconnected HYDRA COMPACT TWIN software is running starts running after successful configuration HYDRA COMPACT TWIN software is down module status is not OK I2C error or board error module status is OK HYDRA COMPACT TWIN software is running starts running after successful configuration HYDRA COMPACT TWIN software is down module status is not OK 12C error or board error module status is OK Table 3 1 Allocation of LEDs on front of HYDRA COMPACT TWIN Details concerning softw
13. V Projection Systems Belgium Noordlaan 5 B 8520 Kuurne Phone 32 56 368 211 Fax 32 56 368 251 E mail support bcd barco com Web www barcocontrolrooms com Barco Hydra Compact Twin R59770027 Revision 13 February 2007 7 2 8 Index 8 Index 8 1 List of tables Table 3 1 Allocation of LEDs on front Of HYDRA COMPACT TWIN i 3 3 Table 3 2 Writing on the audio DOA cc ccccscsessscscscscscsesesssssssesssssssscesececscsesesssssssssasasssasseseseseseseesseseescecseaeseseas 3 19 Table 4 1 BIOS settings Of SBC iii 4 2 Table 4 2 Realtek boot agent settingS iii 4 2 Table 4 3 relation of video properties iii 4 4 Table 6 1 HYDRA COMPACT TWIN technical data i 6 2 Table 6 2 HD SDI video input card technical data ii 6 2 Table 6 3 Quad analog video input card technical data i 6 3 Table 6 4 Quad SDI video input card technical data ccc ccseseseseseseseesescesesesescscscscecsesesesssssssaeacseseseseseseeeseeees 6 3 Table 6 5 Streaming video card technical data ii 6 4 Table 6 6 RGB input card technical data ii neeese nnnnnnn cnn 6 5 Table 6 7 Overlay input card OVL IPU 4 technical data ii 6 5 Table 6 8 DVI video output card technical data i 6 5 Table 6 9 Outpu
14. connected to a monitor and a keyboard therefore follow the steps below e Halt the sections of the HYDRA COMPACT TWIN When they have halted switch off the HYDRA COMPACT Twin by the power switch 5 on the front of it see section 3 3 3 Switching off e Connect a monitor to the VGA connector 2 of the single board computer and a PS 2 keyboard to the PS 2 keyboard mouse connector 6 of the single board computer see section 3 2 2 Single board computer e Switch on the Hyora COMPACT TWIN by pressing the power switch 5 of the HYDRA COMPACT TWIN again e keep the DEL key of the keyboard pressed until the BIOS setup has started If the DEL key was pressed too late and the possibility to enter the setup has passed restart the HYDRA COMPACT TWIN with the key combina tion CTRL ALT DEL e To enter the boot agent setup press keep the SHIFT and F10 key of the keyboard pressed until the boot agent setup is started 4 1 2 BIOS settings The table below lists the Hyora specific BIOS settings that must be selected for proper operation of the SBC path setting Advanced BIOS Feature gt First Boot Device CDROM Advanced BIOS Feature gt Second Boot Device LAN Advanced BIOS Feature gt Third Boot Device Floppy Advanced Chipset Features gt Frame Buffer Size 32M Advanced Chipset Features gt Panel Type 06 Integrated Peripherals gt Primary Master PIO Mode 3 Table 4 1 BIOS settings of SBC mentioned above Nevertheless if so please r
15. connector e Connect the cold output of the source via the cold wire of the cable to v of the EDAC connector e Connect the ground shield of the source via the ground shield of the cable to the GND of the EDAC connec tor Three Wire Analog Unbalanced Connection e Connect the hot output of the source via the hot wire of the cable to v of the EDAC connector e Connect the ground shield of the source to the ground shield of the cable e Connect the ground shield of the source to the v of the cable e Connect v of the cable with the v of the EDAC connector e GND of the EDAC connector is usually not connected but depending on the source it could be necessary to connect the GND of the EDAC connector also Two Wire Analog Unbalanced Connection e Connect the hot output of the source via the hot wire of the cable to v of the EDAC connector e Connect ground shield of the source via the ground shield of the cable to v of the EDAC connector e GND of the EDAC connector is usually not connected but depending on the source it could be necessary to connect the GND of the EDAC connector also Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 21 3 Getting started When connecting digital unbalanced ADS3 ID 75 audio signals to a digital unbalanced board the following wir ing can be used Three Wire Digital Unbalanced Connection e Connect the hot output of the source via the hot wire of the cable to v of the EDAC c
16. instructions indicated by this symbol there is a risk of damage to parts Which are sensitive towared electrostatic charge Oy If you do not heed instructions indicated by this symbol there is a risk to get harmed by sharp objects FA If you do not heed instructions indicated by this symbol there is a risk that parts may explode If you do not heed instructions indicated by this symbol there is a risk that hot parts impact persons or objects IN The sheet icon indicates additional notes 0 Next to this icon you find further information This arrow marks tips 0 Next to this icon you find important notes SO Barco Hydra Compact Twin R59770027 Revision 13 February 2007 1 3 1 Introduction 1 3 Safety instructions This section describes safety precautions which must be observed when installing and operating a product from Barco 1 3 1 Standards Safety regulations HYDRA COMPACT TWIN is built in accordance with the requirements of the international safety standard IEC 60950 1 UL 60950 1 and CSA C22 2 No 60950 1 03 which are the safety standards of information technology equipment including electrical business equipment These safety standards impose important requirements on the use of safety critical components materials and isolation in order to protect the user or operator against the risk of electric shock and energy hazard and having access to live parts Safety standards al
17. standard web browser is required The HYDRA COMPACT TWIN is optimized for uninterrupted fault free operation Therefore a redundant power supply with three power modules and individual power inputs is used In this way failing of one power net or power supply module will not power down the HYDRA COMPACT TWIN The operating system is burned on CD and by this can not get corrupt For data storage a flash disk is used In addition the output of one HYDRA COMPACT TWIN section can be inserted to another HYDRA COMPACT TWIN section in case that a projection module of one section fails the other section displays a combined output of both units The iSrupio software enables to easily operate the two sections of one HYDRA COMPACT TWIN or even multiple HYDRA COMPACT TWIN units commonly as one wall The figure below shows a Display Wall consisting in four projection modules each connected to one HYDRA COM PACT TWIN These HYDRA COMPACT TWIN units are connected via the LAN to a PC that enables the control of HYDRA COMPACT TWIN units and their output for the Display Wall by means of the iSrupio GUI available through the web browser The various input sources are directly connected to the HYDRA COMPACT TWIN units Temaj Sources Figure 2 1 Setup with 2 HYDRA COMPACT TWIN Barco Hydra Compact Twin R59770027 Revision 13 February 2007 2 2 2 Summary iStudio The iStupio software enables the control of the HYDRA COMPACT TWIN as we
18. video input cards HD SDI video input cards Quad analog video input cards and RGB input cards Audio metering information of analog digital or embedded audio sources can be processed with digital or analog audio cards or the external NGM 164 audio metering box Thus each Hyora device is able to monitor video sources and audio metering information Depending on the configuration this video RGB and audio information is provided as analog digital or video output signal or combinations of them to display the sources on a visualization system Furthermore a HYDRA device processes tallies and different kind of VBI Either hardware tallies connected via GPIO or software tallies can be used Closed captions XDS wide screen signaling and VITC can be detected and displayed The HYDRA COMPACT TWIN in particular consists of two independent Hyora sections Each section provides the func tionality of a complete HYDRA device as explained above The sections operate completely independent from each other with their own single board computer overlay input card video and RGB input cards audio cards and output card Thus one section of a HYDRA COMPACT TWIN might integrate up to three input cards which results in up to 12 video sources or up to 112 audio sources 56 stereo pair or 112 mono channels The HYDRA COMPACT TWIN runs a web server This enables to simply connect to and operate the HYDRA COMPACT TWIN from any PC connected to the same LAN On the PC simply a
19. 0 20a followed by the overlay input 15 21 The next four slots may be used with Video and RGB input cards output cards and audio cards 16 19 22 25 If only one section is equipped then this is section 1 On the left side of the back of HYDRA COMPACT TWIN is the power supply located consisting of three power modules 27 29 one under the other Each is equipped with a mains connection 32 34 and can be connected to an independent power net The power supply is commonly used by both sections To protect HYDRA COMPACT TWIN from overheating the air supply openings in the case shall be kept free of obstructions Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 4 3 Getting started The Power Modules Detail The power modules on the back of HYDRA COMPACT TWIN look like this or similar 32 33 34 35 36 37 38 32 33 34 mains connection 35 vent for fan 36 rubber handle bar 37 green LED 38 metallic handle bar Figure 3 3 Power module on the rear of HYDRA COMPACT TWIN On the left side of the power module there is the mains connection 32 33 or 34 in the middle there is the air supply and on the lower right side there is a green LED 37 indicating operation of the power module if lightened Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 5 3 Getting started 3 2 Cabling 3 2 1 Power supply Check the power rating on your outlet before connecting HY
20. 01 R9832530 R98324401 R9832490 R9832680 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 user s manual HYDRA COMPACT TWIN English user s manual iSrupio English iSrupio Manuals amp Supplement CD ROM HYDRA COMPACT TWIN base unit Quad SDI video input card for HYDRA HD SDI video input card for HYDRA Quad analog video input card for HYDRA Streaming video card for HYDRA RGB DVI input card for HYDRA DVI DVI digital output card with scaling for HYDRA DVI DVI digital analog output card for HYDRA DVI DVI digital output card for HYDRA DVI video output card for HYDRA audio input card for Hyora mother board audio input card for Hyora analog daughter board audio input card for Hyora digital daughter board balanced audio input card for Hyora digital daughter board unbalanced PARTHENOPE Audio BreakOut box 56 channel PARTHENOPE Audio BreakOut box 112 channel connector EDAC 90 male patch panel 15x2 BNC cable set D15 BNC 5 x BNC RGB 15 m cable set DVI 5xBNC VGA DVI A cable 2m spare Quad SDI video input card for HYDRA spare HD SDI video input card for HYDRA spare Quad analog video input card for HYDRA spare Streaming video card for HYDRA spare RGB DVI input card for HYDRA spare audio input card for Hyora mother board spare audio input card for HyoRA analog daughter board spare audio input card for Hyora digital daughter board balanced spare audio input card for Hyora digital da
21. 3 23 3 2 10 Patel panel 3 i ss mian enko deere kn ks onu enlu la ebie nasal 3 24 33 Startiho Ups zon lidi iturin E A an ei oa fu nunu Dei 3 25 3 351 COMEN ree ondate Lila EAE A EE E A E E A E EEE N NANAS 3 25 33 2 SWITCHING Mii Cheese o KO ai eaten eee nae At SAE ae 3 26 333 SWITCHING SOU sn EN RARA te ees NE rages oe TN eens eae eee Re 3 26 4 Operating isin tees ses ted ss arb ad ak awl TTTEIITTTRITTTTTETTTETTTTTTETETTTTTITTTTTTTTTTTTITEFTTTETTEE TOATTTTL 4 1 4 1 BIOS and boot agent settings i 4 2 4 1 1 Entering the BIOS or boot agentes renier inei E EEE AE AE 4 2 Ae AOS SENN S a ara alia A re mn PO TO a SENS 4 2 4 3 Boot aqentsettliQ5 s sxss SSL GNUS GN GDU GUGL DIGNA UN A 4 2 4 1 4 Finishing the setup of BIOS and boot agent iii 4 3 4 2 Additional video related INput iii 4 4 4 2 1 Capability of the input cards ii 4 4 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 V 4 3 RedUndant operatlON sss wae eas eh na nana ban Gaskona ce ah Sea Scene ended EA dO 4 5 AA Dual mode sss deisel goes a SOS NR ET Mele OOO 4 7 5 Mantente 5 1 5 1 EXclianqe ol cofisumables s sss eko ta e a a em l ote 5 2 5 1 1 Exchange of the power MOdule iii 5 2 5 1 2 Replacing the filter pad of Hydra Compact TWIN iii 5 3 SA ao nia boia lia sa alii 5 4 o Teclimita FappendiXk alal eran SIS 6 1
22. 4 5V power 5 not connected 13 not connected 4 not connected 12 not connected 3 TMDS data2 shield 11 TMDS data1 shield 2 TMDS data2 10 TMDS data1 1 TMDS data2 9 TMDS data1 6 Technical appendix C4 not connected C3 not connected 24 TMDS clock 23 TMDS clock 22 TMDS clock shield 21 not connected 20 not connected 19 TMDS data0 shield 18 TMDS data0 17 TMDS data0 Figure 6 6 DVI I connector DVI DVI digital output card with without scaling pin assignment DVI DVI digital analog output card DVI video output card DVI I connector c2 green c5 ground C1 red 8 Vsync 16 hot plug detect 7 DDC serial data 15 ground 6 DDC serial clock 14 5V power 5 not connected 13 not connected 4 not connected 12 not connected 3 TMDS data2 shield 11 TMDS data1 shield 2 TMDS data2 10 TMDSdata1 1 TMDS data2 9 TMDS data1 C4 HSync c3 blue 24 TMOS clock 23 TMDS clock 22 TMOS clock shield 21 not connected 20 not connected 19 TMDS data0 shield 18 TMDS data0 17 TMDS data0 Figure 6 7 DVI I connector DVI DVI digital analog output card and DVI video output card pin assignment Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 9 DVI video output card BNC connector 1 Signal Overlay Input Card OVL IPU 4 A A N NW DSU DN 0 uu Ss WN unused unused unused DDC serial data DDC serial clock unused unused TMDS data2 shield TMDS data2 TMDS data2 Genlo
23. 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 GND GND DIN O not connected DIN 1 not connected DIN 2 not connected DIN 3 not connected DIN 4 not connected DIN 5 not connected DIN 6 not connected GND GND DIN 7 not connected DIN 8 not connected DIN 9 not connected DIN 10 not connected DIN 11 not connected DIN 12 not connected DIN 13 not connected GND GND 6 Technical appendix Figure 6 13 SCSI4 female connector digital audio daughter board pin assignment 6 13 6 Technical appendix Analog EDAC Connector on Parthenope o O E E Q E e of Of Figure 6 14 Analog EDAC connector pin assignment Digital EDAC Connector on Parthenope Figure 6 15 Digital EDAC connector pin assignment 6 14 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 3 Order codes Hardware R59770027 R5976569 R5976593 R9830962 ROPT1913 ROPT1867 ROPT1933 ROPT1951 ROPT1851 ROPT2059 ROPT1958 ROPT1959 ROPT2022 ROPT1766 ROPT1767 ROPT1768 ROPT1914 R9830975 R9830970 R9830990 R9830985 ROPT1771 ROPT1960 B5580602 Hardware spareparts R9851720 R9830995 R9851770 R9842320 R9830961 R9832460 R9832470 R9832480 R9851730 R9830968 R9842290 R9842280 R9842520 R9851790 R985180
24. 60Hz analog audio 50 kO 0 dBu 24 dBu from 15Hz to 23 2kHz stereo 18 bit converter 48 kHz per channel Balanced Digital Audio Daughter Board input input type input compatibility input interface sampling frequency digital AES EBU audio differential RS422 transformerless professional 32 44 1 48 kHz detected via input Table 6 11 DVI DVI digital output card technical data Table 6 12 analog audio daughter board technical data Table 6 13 balanced digital audio daughter board technical data Unbalanced Digital Audio Daughter Board input input type sampling frequency Barco Hydra Compact Twin R59770027 Revision 13 February 2007 digital AES EBU audio AES3 id 75 Q unbalanced 32 44 1 48 kHz detected via input Table 6 14 unbalanced digital audio daughter board technical data 6 6 6 Technical appendix 6 2 Interfaces Seen from outside of HYDRA COMPACT TWIN Quad Analog Video Input Card Quad SDI Video Input Card and HD SDI Video Input Card O 1 Signal 2 Shield Figure 6 1 BNC connector Quad analog Quad SDI HD SDI video input card pin assignments HD SDI Video Input Card 8 pin RJ45 connector GND GPIO3 channel A GPIO3 channel B GPIO1 channel A GPIO1 channel B GPIO2 channel A GPIO2 channel B GND 5 6 7 8 Sw MN Figure 6 2 Connector for GPIO insertion HD SDI video input card pin assignment Quad Analog Video Input Card and Quad S
25. DI Video Input Card 10 pin RJ45 connector 10 1 1 GND 6 GPIO2 channel A 2 GPIO2 channel D 7 GPIO2 channel B 3 GPIO1 channel D 8 GPIO1 channel A 4 GPIO2 channel C 9 GPIO1 channel B 5 GPIO1 channel C 10 GND Figure 6 3 Connector for GPIO insertion Quad analog Quad SDI pin assignment Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 7 Streaming video card DyN TD TD RD RGB Input Card C2 C1 N AIN Wa UIO Barco Hydra Compact Twin R59770027 Revision 13 February 2007 Analog Green Analog Red Analog VSync DDC Data DDC Clock unused unused TMDS Data2 shield TMDS Data2 TMDS Data2 c5 16 15 14 13 12 10 RD o JO UL 6 Technical appendix Figure 6 4 RJ 45 connector Streaming video card pin assignment Analog Ground analog R G amp B return Hot Plug Detect Ground return for 5V Hsync and Vsync 5V unused unused TMDS Data1 shield TMDS Data1 TMDS Data1 C4 C3 24 23 22 21 20 19 18 17 Analog HSync Analog Blue TMDS Clock TMDS Clock TMDS Clock Shield unused unused TMDS Data0 shield TMDS Data0 TMDS Data0 Figure 6 5 DVI I connector RGB input card pin assignment 6 8 DVI DVI digital output card and DVI DVI digital output card with scaling c2 not connected c5 ground C1 not connected 8 not connected 16 hot plug detect 7 DDC serial data 15 ground 6 DDC serial clock 1
26. DRA COMPACT TWIN to the wall outlet or to a power strip Contact your facilities manager or a qualified electrician if you are not sure what type of power is supplied to your building HYDRA COMPACT TWIN is designed to operate with single phase power systems having a grounded neutral conductor To reduce the risk of electrical shock do not plug into any other type of power system The HYDRA COMPACT TWIN has three power inputs for connection to independent power nets To connect HYDRA COM PACT TWIN to the power supply follow these steps e Plug the female end of the power cords into the mains connections 32 33 and 34 Figure 3 4 Mains connection of HYDRA COMPACT TWIN e Plug the male end of the power cord into the designated power outlet e Connect all power modules in this manner Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 6 3 Getting started 3 2 2 Single board computer The two single board computers of the HYDRA COMPACT TWIN are each connected to the LAN via their Ethernet con nectors Connectors The connectors of the single board computer are not only on the front plate of the single board computer but also on a corresponding slot plate for the serial port please see the figure below serial port VGA connector only used for service green LED Ethernet connector yellow LED PS 2 keyboard or PS 2 mouse only used for service reserved for future use a ou BBWS
27. February 2007 2 3 3 Getting started 3 Getting started This chapter describes the set up of HYDRA COMPACT TWIN If your HYDRA COMPACT TWIN is already configured within your working place you can skip this chapter and continue with chapter 4 Operating 3 1 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 Getting started 3 1 Examining 3 1 1 Hydra Compact Twin The Front The front of your Hyora Compact Twin looks like this or similar 1 2 HYDRA COMPACT A 1 air supply 2 handle of filter mounting 3 air supply 4 buzzer reset button 5 power switch 6a CD ROM drive of section 1 6b CD ROM drive of section 2 7 green LED power 8 LED A1 green 9 LED B1 red 10 LED A2 green 11 LED B2 red 12 LED A3 green 13 LED B3 red Figure 3 1 Front view of HYDRA COMPACT TWIN Between the air supply openings 1 and 3 on the left side there is the handle of the filter mounting 2 In the middle there is the buzzer reset button 4 and under it the power switch 5 Next to the two buttons there are seven LED s please see also the table below On the right side there are the CD ROM drives 6 The lower one 6a belongs to section 1 the upper one 6b belongs to section 2 Please be carefull when inserting a CD the CD ROM drive closes automatically after a while Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 2 3 Getting started
28. NOPE looks like this or similar EDAC 90 connectors 1 4 5 8 Respective SCSI connectors Figure 3 18 Rear view of PARTHENOPE On the rear of PARTHENOPE there may be two or four EDAC 90 connectors 1 4 if not installed on the front and according to the number of EDAC 90 connectors two or four SCSI connectors 5 8 The SCSI cable between the audio boards and Parthenope are not very strong Handle them with care Do not bend Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 20 3 Getting started Connection to the EDAC Connectors The EDAC connector has 28 inputs Each of these inputs consists of three jacks To connect an analog audio stereo source two adjacent inputs are needed The input with the odd number is used for the left channel the input with the even number is used for the right channel This means that 14 ste reo sources can be connected per EDAC connector To connect a digital audio source only the inputs with the odd numbers are used This means that also 14 stereo sources can be connected Each channel has three connections the hot connection v the cold connection v and the ground gnd To receive the best noise immunity when connecting the various sources to the EDAC connector the following instructions must be followed for analog audio sources Three Wire Analog Balanced Connection e Connect the hot output of the source via the hot wire of the cable to v of the EDAC
29. User s manual Hydra Compact Twin R59770027 Current version Title HYDRA COMPACT TWIN User s manual ID no R59770027 Revision 13 Date February 2007 main issue update chapter 1 new chapter 2 new chapter 3 new chapter 4 new chapter 5 new chapter 6 new chapter 7 new chapter 8 new new The corresponding chapters are new or completely revised corr Passages of the corresponding chapter were corrected see modification bars add Passages of the corresponding chapter were added see modification bars This manual refers to following hardware components of HYDRA COMPACT TWIN Hydra Compact Twin unit R9830962 Document history Modifications which result in a new version are indicated by a vertical bar PanelLink is a Trademark of Silicon Image Barco Hydra Compact Twin R59770027 Revision 13 February 2007 il Trademarks Brand and product names mentioned in this manual may be trademarks registered trademarks or copyrights of their respective holders All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers Copyright 1998 2007 by Barco Die Weitergabe sowie die Vervielfaltigung aller Unterlagen die von uns berlassen werden deren Verwertung und Mitteilung ihres Inhaltes an Dritte ist nicht gestattet soweit dies nicht ausdr cklich zugestanden ist Urheberrechte insbesondere auch solche an Softwa
30. a spare module without power down the HYDRA COMPACT TWIN Besides the alarm buzzer there is a visual indication of a power failure via the green LED 7 at the front This LED is blinking in case of a power error Then the defective power module can be located by examining the individual LED s 37 of the power modules at the back of HYDRA COMPACT TWIN If the green LED on a power module is off the module is defective and must be replaced Exchange of the power module Only authorized personnel should carry out this maintenace work e Locate the defective power module by examining the green LED s 37 on the individual power modules If an LED is not lightened the respective power module is defective e Unplug the power cord from the mains connection 32 33 or 34 of the defective power module e Loosen the securing screw 31 at the lower side of the bracket 30 that fixes the power modules with a size 2 Phillips screwdriver and remove the bracket Keep the bracket and the screw Use gloves to remove the power module The cover of the power module is been used as heat sink for cooling usually the temperature is around 50 60 Celsius under full condition e Press the metallic handle bar 38 towards the rubber handle bar 36 unless the power module is no longer locked in the housing and pull it outwards Put the power module aside for cooling down Keep it away from other people unless it has cooled down e T
31. age and frequency of your power supply match those printed on the device label with the rated electrical values e If you are not sure of the type of AC power available consult your dealer or local power company e This product is equipped with a 3 wire grounding plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the purpose of the ground ing type plug e This equipment must be grounded earthed via the supplied 3 conductor AC power cables If the supplied power cables are not the correct on consult your dealer Barco Hydra Compact Twin R59770027 Revision 13 February 2007 1 4 1 Introduction Mains lead AC Power cords with CEE 7 plug The wires of the mains lead are colored in accordance with the following code yellow green Earth Ground blue Neutral brown Line Live Figure 1 1 CEE 7 plug Power cord with NEMA 5 15 plug The cord set must be UL approved and CSA certified The minimum specification for the flexible cord is No 18 AWG Type SVT or SJT 3 conductor The cord set must have a rated current capacity of at least 10A The attachment plug must be an Earth grounding type with a NEMA 5 15P 10A 125V configuration The wires of the power cords are colored in accordance with the following code
32. ake a good power module Insert the power module into the system Push it inside the housing unless the metallic handle bar 38 snaps in e Reattach the bracket 30 and fix the securing screw 31 e Re plug the power cord to its mains connection 32 33 or 34 e Check if the green LED 37 turns on e Check the green LED power failure 7 which indicates the total power system status The LED may not blink Barco Hydra Compact Twin R59770027 Revision 13 February 2007 5 2 5 Maintenance 5 1 2 Replacing the filter pad of Hydra Compact Twin The filter pad of the HYDRA COMPACT Twin case has to be changed in intervals depending on the grade of pollution of the air The air filter is located behind the ventilation slits on the front of HYDRA COMPACT TWIN Unlock the front cover of the HYDRA COMPACT TWIN with the key Pull the handle of the filter mounting 2 into your direction Pull out the filter mounting to the right Remove the old filter pad Insert a new filter pad Insert the mounting into the HYDRA COMPACT TWIN until the handle engages Lock the front cover Barco Hydra Compact Twin R59770027 Revision 13 February 2007 5 3 5 Maintenance 5 2 Cleaning To keep the cabinet looking brand new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution Never use strong solvents such as thinner or ben zine or abrasive clea
33. are heartbeat 10 12 and system errors 11 13 can be seen in the Module Status and Wall Alarms list please refer to the sections Module Status and Wall Alarms Area in the iSrupio user s manual Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 3 3 Getting started The Back The back of your Hyora Compact Twin looks like this or similar 14a 15 16 17 18 19 204 20 21 22 23 24 25 14 section 1 single board computer 14a section 1 serial port extension of single board computer 15 section 1 overlay input 16 19 section 1 slots for video and RGB input cards output cards and audio boards eg 16 18 input cards 19 output card 20a section 2 serial port extension of single board computer 20 section 2 single board computer 21 section 2 overlay input 22 25 section 2 slots for video and RGB input cards output cards and audio boards eg 22 24 input cards 25 output card 27 power module 1 28 power module 2 29 power module 3 30 bracket 31 securing screw 32 mains connection 1 33 mains connection 2 34 mains connection 3 Figure 3 2 Rear view of HYDRA COMPACT TWIN All boards are inserted in the middle and right part of the back of HYDRA Compact TWIN Each seven adjacent slots form one section Section 1 is on the left part and section 2 on the right part of the slots The cards in both sec tions are arranged after the same scheme On the left is the single board computer 14 14a 2
34. ax 0 5V input signal logic high high impedance logic low max 0 7V FORMAT LINES WORDS 1035 1035 1080 1080 1080 1080 1080 1080 1080 1080 1080 720 720 A EE Gal tank Gey tee 1920 1920 1920 1920 1920 1920 1920 1920 1920 1920 1920 1280 1280 Table 6 1 HYDRA COMPACT TWIN technical data FRAME RATE FIELDS 30 30 1 001 25 30 30 1 001 25 30 30 1 001 25 24 24 1 001 60 60 1 001 P Table 6 2 HD SDI video input card technical data mo as mej me mel moj SS Se Se eS 6 2 6 Technical appendix Quad Analog Video Input Card socket composite video input GPIO video timings Quad SDI Video Input Card socket SDI input GPIO video timings input for composite video signal BNC signal max 1 0V 75 Q terminator DD RJ45 connector 10 pins internal pull up resistor of 10k output signal logic high min 4 5 V logic low max 0 5V input signal logic high high impedance logic low max 0 7 V PAL BDGHI NTSC M Japan SECAM NTSC 4 43 PAL M PAL N Table 6 3 Quad analog video input card technical data input for SDI video signal BNC signal SMPTE 259M C 270Mbps 4 2 2 compliant RJ45 connector 10 pins internal pull up resistor of 10k output signal logic high min 4 5 V logic low max 0 5 V input signal logic high high impedance logic low max 0 7 V NTSC 4 2 2 component 13 5 MHz Y sampling PAL 4 2 2 component 13 5 MHz Y sampling Table 6 4 Quad SDI vi
35. ck input PAL or NTSC VITC input unused unused unused c5 16 15 14 13 12 11 10 00 10 6 Technical appendix vor 2 Shield Figure 6 8 BNC connector DVI video output card pin assignments ground c4 unused c3 unused hot plug detect 24 TMOS clock ground 23 TMDS clock 5V power 22 TMDSclock shield unused 21 unused unused 20 unused TMDS data1 shield 19 TMDS data shield TMDS data1 18 TMDS data0 TMDS data1 17 TMDS data0 Figure 6 9 DVI I FBS P29 connector overlay input card OVL IPU 4 pin assignment 6 1 11 5 15 10 ground 11 unused ground 12 unused ground 13 LTC input unused 14 LTC input ground 15 unused Figure 6 10 Sub D15 connector overlay input card OVL IPU 4 pin assignment Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 10 Breakout Cable for overlay input card OVL IPU 4 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 red wire green wire grey wire black wire BNC 1 BNC 1 BNC 2 BNC 2 XLR 2 XLR 1 XLR 3 XLR 1 a E 6 Technical appendix BNC genlock PAL or NTSC shield VITC PAL or NTSC shield LTC high shield LTC low shield Figure 6 11 Breakout Cable for overlay input card OVL IPU 4 pin assignment 6 11 Analog Audio daughter Board 1 GND 2 GND 3 AINL 0 4 AINR 0 5 AINL 1 6 AINR 1 7 AINL 2 8 AINR 2 9 AINL 3
36. ctors of the single board computers Please refer to section 3 2 2 Single board computer Connect your video sources to the video input cards and the RGB sources to the RGB input cards if advisable use the patch panel Please refer to section 3 2 4 Video Input Card 3 2 5 RGB Input Card and 3 2 10 Patch panel Connect the intended display devices to the output cards Please refer to section 3 2 6 Output Card If necessary connect the audio sources to the digital and analog audio daughter boards Please refer to section 3 2 7 Audio Board and 3 2 8 Parthenope If information of an NGM 164 is used check that it is connected to the LAN please refer to section 3 2 9 NGM 164 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 25 3 Getting started 3 3 2 Switching on When taking the HYDRA COMPACT Twin for the first time into operation first an iSrupio Hydra boot CD must be inserted into each CD ROM drive Therefore follow the above mentioned steps e To switch on the HYDRA COMPACT TWIN press the power switch 5 on the front of HYDRA COMPACT TWIN e Check the state of the green LED power 7 on the front of HYDRA COMPACT TWIN It must be permanently on to indicate that the power supply operates properly If this is not the case see section 7 1 Hydra Compact Twin does not start up please e Open the CD ROM drive 6 If the CD ROM drive does not stay open retry opening it until it stays open e Insert the iStupio
37. damage and also damage attributed to the operation of software as well as to other services provided by Barco being a component of the system or independent services will be deemed invalid provided the damage is not proven to be attributed to the absence of properties quaranteed in writing or due to the intent or gross negligence on the part of Barco If the purchaser or a third party carries out modifications or repairs on good delivered by Barco or if the goods are handled incorrectly in particular if the systems are commissioned or operated incorrectly or if after the transfer of risks the goods are subject to influences not agreed upon in the contract all guarantee claims of the purchaser will be rendered invalid Not included in the guarantee coverage are system failures which are attrib uted to programs or special electronic circuitry provided by the purchaser e g interfaces Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer Barco Hydra Compact Twin R59770027 Revision 13 February 2007 ili Revision sheet To e Barco Control Rooms GmbH An der Rossweid 5 D 76229 Karlsruhe Phone 49 721 6201 0 Fax 49 721 6201 298 E mail docu de bcd barco com Web www barcocontrolrooms com From Date Please correct the following po
38. deo input card technical data Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 3 Streaming video card socket video formats compression algorithm bitrate digital network carrier network transmission protocol connection protocols supported encoders 6 Technical appendix 2 x RJ45 connector 8 pin for redundant connection PAL NTSC MPEG 1 ISO 11172 MPEG 2 ISO 13818 MP ML 4 2 0 DVB ETR 154 SPTS MPTS the DVB format is MPEG 2 based MPEG 4 part 2 ISO 14496 2 SP L3 ASP L5 Bosch MPEG 4 h263 MJPEG ISO 10918 MXPEG 2D Wavelet 1 4 streams and max 44Mbps per board MPEG 1 up to 4 streams all resolutions MPEG 2 up to 4 D1 streams or 4 CIF streams 44Mbps per board max 15Mbps per stream MPEG 4 part 2 up to 4 CIF streams or 3 2CIF streams or 1 2 4CIF streams depends on resolution 32Mbps per board max 8Mbps per stream MPEG 4 h263 up to 4 CIF streams or 4 2CIF streams or 4 4CIF streams MJPEG up to 4 CIF streams or 2 4 4CIF streams Visiowave 1 3 D1 streams or up to 4 CIF streams depends on reso lution TRANSFORM SCN 1 stream Base T Ethernet 10 100 Mbps UDP RTP variable header length lost packet detection packet recorder non video packet detection IGMP v2 and v3 multicast subscription MPEG 2 Bosch Coretec Cornet Exterity Fast Video Security HaiVision iMPath Lanaccess Mavix NKF Optibase Path1 PelcoNET Siemens OTN Tandberg Teleste Telin
39. dules or monitors for the graphical output of the HYDRA Compact TWIN The output data is provided for analog and digital connection The card allows additionally scaling of the output The front plate is labeled with OPU DD The text next to the con nectors reads as dvi ana1 2 Connectors On the DVI DVI digital analog output card there are two DVI I connectors 1 DVI I connector for digital or analog output channel 1 2 DVI I connector for digital or analog output channel 2 3 green LED output channel 1 lightens up once after successful boot process 4 green LED output channel 2 lightens up once after successful boot process Figure 3 13 Connectors of DVI DVI digital analog output card Dual Mode To use dual mode the second output channel is used for a second display device Please refer to section 4 4 Dual mode for the appropriate cabling 3 16 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 Getting started DVI DVI digital output card The DVI DVI digital output card provides the facility to connect two projection modules or monitors for the graphi cal output of the HYDRA COMPACT TWIN The output data is provided for digital connection The front plate is labeled with OPU DDD Connectors On the DVI DVI digital output card there are two DVI I connectors 1 DVI I connector for digital output channel 1 2 DVI I connector for digital output channel 2 3 green LED output channel 1 lightens up once afte
40. eadjust the BIOS to the above Hydra Compact Take care not to use the entry default settings as this applies other settings than Twin settings 4 1 3 Boot agent settings It is important that the boot agent uses correct settings to prevent it to try to boot from the network which would increase startup time of the HYDRA Compact TWIN These settings are pre configured in your HYDRA COMPACT TWIN In case they have been changed please use the table below as a reference to readjust the settings path setting Network Boot Protocol PXE Boot Order Int 18h Show Config Message Enable Show Message Time 3 Seconds Table 4 2 Realtek boot agent settings After readjusting the settings press the F4 key to save the changes and quit Barco Hydra Compact Twin R59770027 Revision 13 February 2007 4 2 4 Operating 4 1 4 Finishing the setup of BIOS and boot agent After selecting the appropriate settings save the settings and exit the BIOS or boot agent setup Halt the HYDRA COMPACT TWIN and switch it off again please see above Now you can safely disconnect monitor and keyboard from the SBC The HYDRA COMPACT TWIN can be taken into its usual operation again Barco Hydra Compact Twin R59770027 Revision 13 February 2007 4 3 4 2 Additional video related input 4 Operating The HYDRA COMPACT TWIN is able to detect and process further video related information This is in particular closed caption CC extended da
41. ected with 10 Mbps 7 stream 1 is active 8 stream 2 is active stream 3 is active 10 stream 4 is active Figure 3 10 Connectors of Streaming video card Connection The two RJ45 network connectors 1 2 establish the connection to the network For a redundant connection a network cable should be plugged into each of the plugs 1 and 2 These network cables should connect on the other side to a redundant network In case of a failure of one connection the other connection will take over the complete network traffic If a redundant connection is not required either plug 1 or plug 2 can be used for the connection Both plugs use the same IP and MAC address thus no configuration in regard of the used plug is required Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 13 3 Getting started 3 2 5 RGB Input Card The RGB input card has two independent DVI plugs to connect two analog or digital RGB sources to the HYDRA COMPACT TWIN Two LED s indicate whether there is a source connected or not one LED for each RGB input chan nel Standards The RGB input card processes analog RGB and HD RGB input signals digital RGB input and component video RGB Connectors On the RGB input card there are two DVI I connectors and two green LED s IN B DVI I connector green LED IN B green LEDINA IN A DVI I connector Sw MN Figure 3 11 Connectors of RGB input card Barco Hydra Compact Twin R59770027
42. ed to the right projection module Please refer also to section 4 4 Dual mode Order The output card is inserted into the slot on the right of the last video RGB input cards looking from the back on the HYDRA COMPACT TWIN 1 There is no empty slot allowed between the last video RGB input card and the output card Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 18 3 Getting started 3 2 7 Audio Board The audio boards serve to monitor audio signals An audio board consists of an audio motherboard and one or two audio daughterboards which are plugged on the audio motherboard Up to two audio motherboards can be used in one HYDRA COMPACT TWIN The audio input is inserted into the audio daughterboards A daughterboard is of analog balanced digital bal anced or digital unbalanced type On an audio motherboard analog and digital daughterboards can be mixed On one daughter board there are 28 mono or 14 stereo channels available This means an audio motherboard may contain 56 channels A HYDRA COMPACT TWIN with maximal two audio motherboards may monitor herewith 112 audio channels Connectors Each audio daughterboard is equipped with a SCSI 4 connector The figure below shows an audio board fully equipped with two daughterboards of digital unbalanced type r 1 SCSI port 1 2 SCSI port 2 Figure 3 16 Connectors of analog and digital daughterboard The writing on the front plate of the audio board diff
43. een LED path D analog video input channel A analog video input channel B analog video channel C analog video channel D RJ45 GPIO connector Oo ON A UI a WO Figure 3 7 Connectors of Quad analog video input card Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 10 3 Getting started Quad SDI video input card On the Quad SDI video input card there are four BNC connectors to insert four SDI video signals a 10 pin RJ45 GPIO connector that enables to have two tallies per video and four green LED s Standards The Quad SDI video input card supports the standard SMPTE 259M C 4 2 2 270Mbps only green LED path A green LED path B green LED path C green LED path D SDI input channel A SDI input channel B SDI input channel C SDI input channel D RJ45 GPIO connector 10 pin Oo ON A LI kW MN Figure 3 8 Connectors of Quad SDI video input card Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 11 3 Getting started HD SDI video input card On the HD SDI video input card there are four BNC connectors two connectors are to insert the HD SDI video signals and two connectors are to loop through the signals to another monitor Furthermore there is a 8 pin RJ45 GPIO connector that enables to have three tallies per video and two green LED s Standards The HD SDI video input card supports the SMPTE 292M standard green LED path B RJ45 GPIO connector 8 pin g
44. epending on the type of the video input card up to 12 video sources can be processed and displayed by one HYDRA COMPACT TWIN section thus the two sections may display up to 24 video sources on two displays Order The video input cards are inserted into the slots on the right of the overlay input card looking from the back on the HYDRA COMPACT TWIN The order of the various video input cards and the RGB input cards can be chosen arbi trarily One exception from this is the combination of Quad SDI video input cards and RGB input cards since the RGB input cards can not be inserted directly to the left of the Quad SDI video input cards Either a card of another type can be inserted between these cards or the RGB input cards can be inserted to the right of the Quad SDI video input cards There is no empty slot allowed between overlay input card and video RGB input cards and between the video RGB input cards themselves Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 9 3 Getting started Quad Analog Video Input Card On the Quad analog video input card there are four BNC connectors to insert four analog video signals a 10 pin RJ45 GPIO connector that enables to have two tallies per video and four green LED s Standards The Quad analog video input card supports composite video with the international broadcasting standards PAL NTSC or SECAM green LED path A green LED path B green LED path C gr
45. ers according to the type of daughter boards which are plugged on it nevertheless the numbering of the ports remains the same The following table lists which writing on the front plate refers to which audio daughter board Writing Type of daughterboard BALANCED ANA Analog balanced BALANCED DIG digital balanced UNBALANCED DIG Digital unbalanced No daughterboard Table 3 2 Writing on the audio board The SCSI cable between the audio boards and Parthenope are not very strong Handle them with care Do not bend If connecting 600 Ohm audio sources to an analog audio daughterboard then to receive best signal quality the audio input at the Hydra Compact Twin should be terminated with a 600 Ohm resistor Order The audio boards are inserted into the slots to the right of the output card looking from the back on the HYDRA COMPACT TWIN 3 19 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 Getting started 3 2 8 Parthenope The audio breakout box PARTHENOPE adapts the audio cabling via EDAC 90 connectors to the SCSI4 input on the audio boards The EDAC 90 connectors on PARTHENOPE can be installed on the front or on the rear of the device The Front The front of PARTHENOPE looks like this or similar Parthenope 1 4 EDAC 90 connectors Figure 3 17 Front view of PARTHENOPE On the front of PARTHENOPE there may be two or four EDAC 90 connectors 1 4 The rear The rear of PARTHE
46. es and further information of both HYDRA COMPACT TWIN sections can be displayed on one projection module but of course with less available space per source Please refer to the iStubio user s manual section Redundant Operation DVI output with DVI video output card With the DVI video output card two cases have to be distinguished If it is the DVI connector that connects to the projection modules then two output cards per HYDRA COMPACT TWIN section have to be used to establish a redun dant setup The DVI connector of the first output card is connected to the projection module to provide the digital or analog data the DVI connector of the second output card is connected to the overlay input card of another HYDRA COMPACT TWIN section In addition the video output of both output cards can be connected to suitable de vices See also the figure below Video output with DVI video output card If the DVI video output card provides a video timing then one output card per HYDRA COMPACT TWIN section is suffi cient to setup a redundant system The suitable BNC connector SDI or CVBS of the output card remains con nected to the displaying device whereas the DVI connector is used to connect to the overlay input card of the other HYDRA COMPACT TWIN and vice versa Please see also the figure below If this configuration is used a DVI timing should be selected Display section 1 Display section 2 Display section 1 Display section 2
47. f Quad SDI video input card ii 3 11 Figure 3 9 Connectors Of HD SDI video input card oe eecccescssssssescscscscscccscsesesesssssssecscassesesesesesesesesesseececececeeaeaes 3 12 Figure 3 10 Connectors of Streaming video Card i 3 13 Figure 3 11 Connectors Of RGB input Card ii 3 14 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 8 1 8 Index Figure 3 12 Connectors of DVI DVI digital output card with SCalinQ iii 3 15 Figure 3 13 Connectors of DVI DVI digital analog output card o ononococococococococonanannnnononononononononononon cano no nono no nora 3 16 Figure 3 14 Connectors of DVI DVI digital output Card iii 3 17 Figure 3 15 Connectors of DVI video output Card i 3 18 Figure 3 16 Connectors of analog and digital daughterboard iiii 3 19 Figure 3 17 Front view Of PARTHENOPE iii 3 20 Figure 3 18 Redi view of PARTHENORE ica en iu aio 3 20 Figure 3 19 Patehipaneli rr Cane ease TRA DIG A ONTO el ON BAR oE 3 24 Figure 3 20 HYDRA COMPACT TWIN Startup SCION i 3 26 Figure 4 1 Hardware configuration for redundant operation with DVI video output card DVI output mode with two output cards per section left and video output mode with one output card per section left 4 5 Figure 4 2 Hardware configurati
48. gives tabular overview about the technical details of HYDRA COMPACT TWIN its components and of their inter faces Troubleshooting gives advice if your HYDRA COMPACT TWIN does not operate properly Index gives an overview about the used tables and figures Chapters pages figures and tables are numbered separately Chapters are indicated by a point syntax e g 4 2 3 pages by a dash syntax e g 2 1 as figures and tables are e g figure 5 4 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 1 2 1 Introduction 1 2 Styles and symbols The typographic styles and the symbols used in this document have the following meaning Bold Labels menus and buttons are printed in the Bold font Condensed Links to both other chapters of this manual and to sites in the Internet are printed condensed In the on line version of this manual all hyperlinks appear teal Courier Names of files and parts from programs are printed in the Courier font Courier bold Inputs you are supposed to do from the keyboard are printed in Courier bold font Within a piece of programming code this arrow marks a line that must be made up in two lines though meant to be one line 5 If you do not heed instructions indicated by this symbol there is a risk of damage to the equipment If you do not heed instructions indicated by this symbol there is a risk of electrical shock and danger to personal health If you do not heed
49. ints in this documentation R59770027 page wrong correct Barco Hydra Compact Twin R59770027 Revision 13 February 2007 Contents INTO Nan 1 1 1 1 How this manual is organized iii 1 2 1 2 Styles andsymbols oscilla seni sea a a AO MEMA NEA 1 3 3 Safety INSITUCHIONS siede DAN on UN kad 1 4 A dS sa ERIN GARA RIG ae aE 1 4 32 PRECAUTIONS e RAIL A AA Ea 1 4 1 3 3 Unpacking Of dEeVicesS an a ai kreata 1 6 13 Alnstallation s ss kase rada 1 6 153 5 SCIVICING 2s ss tah Sn RUA ALA SDS tae NA A ADAS O tana tata 1 6 1 3 6 CleaNlNg 22 pes ms stana mn en MANDA la a nea a an ra akr I 1 6 TS ZaRESDACkINQ Ismene Ree a aloe 1 6 1 4 Online dOCUMEN TATION ss sss E NEA KO tees 1 7 2 SUMMA Yi its dadas 2 1 2AIPI ODEIWIES Sas esar o areas dk ur ed a rad e do do kto und destro 2 2 3 Getting slalle sss delia 3 1 3 EXAMINING 55 mao NS ae ees 3 2 3 1 A Ay dra Com pact TWIN semmi knrn a A 3 2 BGabliniQ sss zs o OS e e eco ees IIA e de ir e 3 6 3 2 IPOWEr SUpplV gt oriana no TAN POR o AN E de a 3 6 3 2 2 Single boafd COMpUlef su o ka a AAA o A A o teas 3 7 3 2 3 0VerlaY INPUVCa U csi it 3 8 3 2 4 Video AMPUL Cal 1 sss sea NU aaa sk nla 3 9 3 2 5 RGB INDU Cd sse bas A NO E A A See 3 14 BDO OUt Put Cand E A ORATORIA 3 15 3 2 7AUdio Boardi tura l nk Noa 3 19 328 Parthenope a Ram LA NESALA In A E KA tates ou DAMO RTE RA RATIO EIO aloe 3 20 B29 ON Eu ko A nr pe nO PE PO the
50. ll as the management of the content of the connected display Multiple HYDRA COMPACT Twin sections and even multiple units can be grouped to a wall and operated commonly Besides of video and audio windows also windows with content like text logos clocks timers stopwatch or alarms can be displayed Furthermore applications and viewers can be started and dis played The arrangement of these windows and the combination of such layouts of different HYDRA COMPACT TWIN sections can be stored and re accessed iSrupio provides the functionality to integrate alarm indicators and the detected VBI and tallies in the respective video windows Parthenope If audio cards are used in the HYDRA COMPACT TWIN the audio breakout box PARTHENOPE provides the possibility to connect two or four EDAC 90 connectors with the audio input and to convert them to two or four SCSI 4 connec tors for insertion at the audio cards PARTHENOPE comes in two versions 56 or 112 mono channel version two or four EDAC 90 connectors NGM 164 The external device NGM 164 sends audio metering data and audio alarms of audio sources via the Ethernet to the HYDRA COMPACT Twin thus enabling to monitor up to 64 or if using multiple NGM 164 units even more audio sources This enables each section to monitor lots of audio channels while reserving all three slots for video and RGB input cards instead of using them for audio cards Barco Hydra Compact Twin R59770027 Revision 13
51. ners since these will damage the cabinet Unplug the device from the wall outlet before cleaning Never clean the case of HYDRA COMPACT Twin without first disconnecting the power supply cords Do not use liquid cleaners or aerosol cleaners Barco Hydra Compact Twin R59770027 Revision 13 February 2007 5 4 6 Technical appendix 6 Technical appendix This chapter provides tabular overview about the technical details of HYDRA COMPACT Twin its components and of their interfaces Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 1 6 1 Technical data Hydra Compact Twin dimensions h w d dimensions h w d with rubber feet fixation handling weight AC power supply mains frequency power consumption inrush current 264 V operating conditions HD SDI Video Input Card socket HD SDI input HD SDI output GPIO resolution Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 Technical appendix 177 mm 440 mm 540 mm 6 97 in 4U 17 32 in 21 3 in 181 mm 483 mm 590 mm 7 20 in 18 98 in 23 2 in 23 kg 50 7 Ibs 100 240 V 50 60 Hz 650 W 80A 0 40 Celsius at 8 80 humidity non condensing input for HD SDI video signal BNC signal SMPTE 292M compliant input for HD SDI video signal loopthrough BNC signal SMPTE 292M compliant RJ45 connector internal pull up resistor of 10k output signal logic high min 4 5V logic low m
52. o DVI video output cards DVI DVI output card digital or digital analog With a DVI DVI output card in dual mode each connector of the card is used to provide data for one projection module Channel one the upper connector is connected to the left projection module looking from front to the projection modules channel two is connected to the right projection module please see also the figure below Display section 1 Hydra Compact Twin SBC OVL IPU OPUJSBC OVL IPU OPU Section 1 Section 2 Figure 4 4 Dual mode connection for a DVI DVI output card Barco Hydra Compact Twin R59770027 Revision 13 February 2007 4 7 5 Maintenance 5 Maintenance The HYDRA COMPACT Twin requires very little maintenance Some maintenance operations are nevertheless neces sary to maintain distortion free operation of the HYDRA COMPACT TWIN Barco Hydra Compact Twin R59770027 Revision 13 February 2007 5 1 5 Maintenance 5 1 Exchange of consumables 5 1 1 Exchange of the power module The HYDRA COMPACT TWIN can be connected to independent power nets If one of the three power modules or a power net is failing you can hear a buzzer alarm that can be reset by pushing the red buzzer reset button 4 at the front of HYDRA COMPACT TWIN The failing power module can be replaced with
53. on for redundant operation with DVI DVI output card with one output card per AMO ii Hipomeno nr re E nn IEI 4 6 Figure 4 3 Dual mode connection for two DVI video output cardS iii 4 7 Figure 4 4 Dual mode connection for a DVI DVI output Card iiiii 4 7 Figure 6 1 BNC connector Quad analog Quad SDI HD SDI video input card pin assignments 6 7 Figure 6 2 Connector for GPIO insertion HD SDI video input card pin assiIgnMEnt iii 6 7 Figure 6 3 Connector for GPIO insertion Quad analog Quad SDI pin assignment iii 6 7 Figure 6 4 RJ 45 connector Streaming video card pin assignment ococonococicccnononononononononononononononcnnn corona nono nononcns 6 8 Figure 6 5 DVI I connector RGB input card pin assignMeEnt iii 6 8 Figure 6 6 DVI I connector DVI DVI digital output card with without scaling pin assignment 6 9 Figure 6 7 DVI I connector DVI DVI digital analog output card and DVI video output card pin assignment 6 9 Figure 6 8 BNC connector DVI video output card pin assignMents n 6 10 Figure 6 9 DVI I FBS P29 connector overlay input card OVL IPU 4 pin assignment s s esis esenee 6 10 Figure 6 10 Sub D15 connector overlay input card OVL IPU 4 pin assigNMent ieisisiseeneeeo 6 10
54. onnector e Connect the ground shield of the source to the ground shield of the cable e Connect the ground shield of the source to the v of the cable e Connect v of the cable with the GND of the EDAC connector e v of the EDAC connector is not connected Two Wire Digital Unbalanced Connection e Connect the hot output of the source via the hot wire of the cable to v of the EDAC connector e Connect ground shield of the source via the ground shield of the cable to the GND of the EDAC connector e v of the EDAC connector is not connected When connecting digital balanced ADS3 110 audio signals to a digital balanced board the following wiring can be used Three Wire Digital Balanced Connection e Connect the hot output of the source via the hot wire of the cable to v of the EDAC connector e Connect the cold output of the source via the cold wire of the cable to v of the EDAC connector e Connect the ground shield of the source via the ground shield of the cable to the GND of the EDAC connec tor It is recommended to only connect suitable digital audio signals to the digital audio boards i e a balanced digital audio signal to a digital balanced audio board or an unbalanced digital audio signal to an unbalanced digital audio board If the signal is not suitable a impedance matching transformer should be used first to convert the signal to a suitable standard Barco Hydra Compact Twin R59770027 Revision 13 Feb
55. r successful boot process 4 green LED output channel 2 lightens up once after successful boot process Figure 3 14 Connectors of DVI DVI digital output card Dual Mode To use dual mode the second output channel is used for a second display device Please refer to section 4 4 Dual mode for the appropriate cabling 3 17 Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 Getting started DVI video output card The DVI video output card provides the facility to connect simultaneously the same content on two display de vices of different type These are on the one hand a projection module or monitor for digital or analog input and on the other hand a device capable to display a video timing The front plate of the DVI video output card is la beled with OPU DV Connectors On the DVI video output card there are three connectors one DVI I connector and two BNC connectors 1 DVI I connector for digital analog output digital and analog signal are available at the same time BNC connector for CVBS output 3 BNC connector for SDI output 4 6 green LEDs 1 3 reserved for future use 7 green LED 4 lightens up once after successful boot process Figure 3 15 Connectors of DVI video output card Dual mode In dual mode a second output card is inserted next to the first output card The first output card must be con nected to the left projection module seen from front of the Display Wall The second output card is connect
56. re werden nur insoweit bertragen als es fiir die Erreichung des speziellen Vertragszwecks erforderlich ist Zuwiderhandlungen konnen zu Schadensersatz verpflichten Alle Rechte aus der Erteilung eines Patents oder der Eintragung eines Gebrauchsmusters verbleiben bei uns Copyright 1998 2007 by Barco All rights reserved No part of this document may be copied reproduced or translated It shall not otherwise be recorded transmitted or stored in a retrieval system without the prior written consent of Barco Guarantee and compensation Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee On receipt the purchaser must immediately inspect all delivered goods for damage incurred during transport as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints The period of guarantee begins on the date of transfer of risks in the case of special systems and software on the date of commissioning at the latest 30 days after the transfer of risks In the event of justified notice of complaint Barco can repair the fault or provide a replacement at its own discretion within an appropriate period If this measure proves to be impossible or unsuccessful the purchaser can demand a reduction in the purchase price or cancellation of the contract redhibition All other claims in particular those relating to compensation for direct or indirect
57. reen LED path A loop through HD SDI channel B HD SDI input channel B loop through HD SDI channel A HD SDI input channel A N Ou ah Y N Figure 3 9 Connectors of HD SDI video input card All unused outputs of the HD SDI video input card 4 and 6 should be terminated with a 75 Ohm BNC terminator Maximum number of HD SDI video input cards The maximum amount of HD SDI video input cards that can be used in one HYDRA COMPACT Twin with redundant usage of the power supply is as follows e max 2 HD SDI video input cards per section e max 4 HD SDI video input cards in one Hydra Compact Twin Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 12 3 Getting started Streaming video card The Streaming video card connects to the Ethernet to receive and process up to four video streams The card is equipped with two RJ45 connectors and with all together eight LED s to indicate the connection status of the board Standards The Streaming video card supports various compression algorithms over Ethernet Please refer also to section 6 1 Technical data for detailed information 1 RJ45 Network connector 1 2 RJ45 Network connector 2 3 green LED connector 1 connected to the Ethernet 4 green LED connector 2 connected to the Ethernet 5 green LED ON connector 1 connected with 100 Mbps OFF connector 1 connected with 10 Mbps 6 green LED ON connector 2 connected with 100 Mbps OFF connector 2 conn
58. ruary 2007 3 22 3 Getting started 3 2 9 NGM 164 If using audio metering information of an NGM 164 it has to be connected to the same LAN as the HYDRA COMPACT TWIN More information can be found in the user manual R59770028 which is also on the iStuDIO S Manuals amp Supplement CD ROM R5976593 please refer to section 1 4 Online documentation Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 23 3 Getting started 3 2 10 Patch panel To easily connect signals provided via cables with BNC connector a BNC patch panel can be used The patch panel is a plate that can easily be fixed into the rack and serves to connect the BNC cables coming from video or RGB sources with the dedicated cables that are connected to the Dual analog video cards of the HYDRA 4 x BNC to HD15P or to the RGB input card It consists of two rows of 15 BNC connectors each The drawing below illus trates the patch panel _ 000000000000000 0000000000000AdO lt Figure 3 19 Patch panel Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 24 3 Getting started 3 3 Starting Up 3 3 1 Connecting First of all you have to provide the appropriate power supply Plug in the power cable on the back panel of your HYDRA COMPACT TWIN Please refer to section 3 2 1 Power supply Connect the sections of your HYDRA COMPACT TWIN to the local area network Connect the network to the Ethernet conne
59. se the command Halt module of the Module menu please refer to the iSrupio user s manual section Module Control This command halts the section of the HYDRA COMPACT TWIN If you want to switch off all HYDRA Com PACT TWIN units of a wall you also can use the command Halt wall from the Wall menu When both sections the HYDRA COMPACT TWIN are halted they stop to send an output signal to the projection modules and they show their original display e g a black or blue screen If so the HYDRA COMPACT TWIN can be switched off with the power switch 5 at the front of it Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 26 4 Operating 4 Operating This chapter provides information about internal settings extended video functionality and advanced configura tions of the HYDRA COMPACT TWIN It does not explain how the HYDRA COMPACT TWIN is used to monitor and display video and RGB sources but this can be found in detail in the iSrupio user s manual iSrupio is just accounted as far as necessary to understand the substance of this chapter Barco Hydra Compact Twin R59770027 Revision 13 February 2007 4 1 4 Operating 4 1 BIOS and boot agent settings The BIOS and boot agent of the single board computer SBC gets pre configured at the factory If there is any how the need to access one of them some hardware configuration must be done 4 1 1 Entering the BIOS or boot agent To access the BIOS the SBC must be
60. so impose requirements to the internal and external temperature variations radiation levels mechanical stability and strength enclosure construction and protection against risk of fire Simulated single fault condition testing ensures the safety of the equipment to the user even when the equip ment s normal operation fails Electromagnetic interference Electromagnetic emission of HYDRA COMPACT TWIN complies with EN55022 EN61000 3 2 EN61000 3 3 and the limits for a class A digital device pursuant to Part 15 of the FCC Rules Electromagnetic immunity of HYDRA COMPACT TWIN complies with EN55024 1 3 2 Precautions For your own protection observe the following safety precautions when installing operating and servicing your device e Before operating the units please read this manual thoroughly and retain it for future reference e Observe all warnings and instructions printed on the devices e Servicing not explicitly mentioned in this manual should never be carried out by unauthorized personnel Never open the case of the unit without first disconnecting both power supply cords e The appliance couplers on this unit must be used for disconnecting the unit from the mains circuit For re moval of all power from the unit always disconnect both supply cords e To prevent fire or electrical shock hazard do not expose this unit to rain or moisture e This product should be operated from an AC power source e Check that the volt
61. t card DVI DVI digital with scaling technical data susesi 6 6 Table 6 10 DVI DVI digital analog output card technical data ii 6 6 Table 6 11 DVI DVI digital output card technical data iii 6 6 Table 6 12 analog audio daughter board technical data i 6 6 Table 6 13 balanced digital audio daughter board technical data ccc cccccsescscscscscscseseseseeseececseseseseseseeeeeeees 6 6 Table 6 14 unbalanced digital audio daughter board technical data u eee 6 6 Tables6 15 Order codes cion sa datado 6 16 8 2 List of figures Foure dA CEE DUO E LI IDO kea a 1 5 Figure 1 2 NEMA 5 15 PIUG ir iaia 1 5 Figure 2 1 Setup with 2 HYDRA COMPACT TWIN iii 2 2 Figure 3 1 Front view Of HYDRA COMPACT TWIN ui 3 2 Figure 3 2 Rear view Of HYDRA COMPACT TWIN ui 3 4 Figure 3 3 Power module on the rear Of HYDRA COMPACT TWIN i 3 5 Figure 3 4 Mains connection of HYDRA COMPACT TWIN L iii 3 6 Figure 3 5 Ports of single board computer 2 and corresponding slot plate nn 3 7 Figure 3 6 Ports of the overlay input card OVL IPU 4 eceeeeceesesesesssseseseeeecesesesesesesesesnsesecseseseeeecetseseesesestsesneeneees 3 8 Figure 3 7 Connectors of Quad analog video input Card iii 3 10 Figure 3 8 Connectors o
62. ta and a D15 connector to insert external time code LTC or VITC or genlock source for synchronization san connector LTC VITC or genlock D15 input connector DVI I for digital graphic data green LED DVI input active green LED active genlock Sw N Figure 3 6 Ports of the overlay input card OVL IPU 4 The green LED 3 on the left indicates if a signal for the background is active The green LED 4 on the right indicates if a genlock LTC or VITC signal is active Order The overlay input card is inserted to the right side of the single board computer looking from back on the HYDRA COMPACT TWIN The timing of the graphical external source should correspond to the timing selected with the istudio GUI Setup Module Timing The DVI connector provides DDC timing information to enable a graphic output device with CE DDC capability to adapt to the required timing Barco Hydra Compact Twin R59770027 Revision 13 February 2007 3 8 3 Getting started 3 2 4 Video Input Card To integrate analog video SDI video and HD SDI video there are different types of video input cards available for use in the HYDRA COMPACT Twin Each board except the Streaming video card is additionally equipped with a RJ45 GPIO connector for user specified functions like tallies or alarms Furthermore there is an LED for each input con nector to indicate if a video connection exists or not D
63. ta structure XDS vertical interval time code VITC wide screen signaling WSS and video index information coding VLI both with an option of the active format descriptor AFD and embedded audio Furthermore tallies and LTC can be processed 4 2 1 Capability of the input cards The above mentioned detection of video related information is not in the same way supported by all of the input cards Please see in the table below the abilities of the various input cards Property CC XDS VITC LTC WSS WSS AFD option VLI VLI AFD option embedded audio hardware tallies Quad SDI input card NTSC only NTSC only OK PAL only PAL only PAL only PAL only OK 2 source HD SDI input card OK 3 source Quad analog video input card NTSC only NTSC only 2 source overlay OK OK input card Table 4 3 relation of video properties The RGB input card and Streaming video card do not support any of the above mentioned properties Barco Hydra Compact Twin R59770027 Revision 13 February 2007 4 4 4 Operating 4 3 Redundant operation Special hard and software configurations can be made to avoid a loss of source control in case that one display fails Depending on the used output cards and the selection of the format of the output data different configura tions must be applied By using special layouts which complement one another when being displayed on top of each other all sourc
64. tal output DVI 1 0 analog output RGB HsVs SDI output SMPTE259 M CVBS output CCIR601 socket 1 x DVI I FBS P29 connector 2 x BNC FBS 750 connector timing Digital output up to iStuDIO timing Barco Projector PU UXGA 60Hz Analog output up to iSTUDIO timing Barco Projector PU UXGA 60Hz SDI output PAL 720x576 NTSC 720x487 CVBS output PAL B D G H 702x575 NTSC PAL M 711x482 Table 6 8 DVI video output card technical data Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 5 Output card DVI DVI digital with scaling 2 channel digital output socket timing DVI 1 0 2 x DVI I FBS P29 connector up to iSrupio timing Barco Projector PU UXGA 60Hz 6 Technical appendix Table 6 9 Output card DVI DVI digital with scaling technical data Output card DVI DVI digital analog 2 channel digital output analog output socket timing DVI 1 0 RGB HsVs 2 x DVI I FBS P29 connector Digital output up to iSTUDIO timing Barco Projector PU UXGA 60Hz Analog output up to iStupio timing Barco Projector PU UXGA 60Hz Table 6 10 DVI DVI digital analog output card technical data Output card DVI DVI digital 2 channel digital output Socket Timing Analog Audio Daughter Board Input input impedance input sensitivity max input level frequency reponse at 3dB points A D converter smapling frequency DVI 1 0 2 x DVI I FBS P29 connector up to iSrupio timing Barco Projector PU UXGA
65. this unit near water e Use only the power cord supplied with your unit While appearing to be similar other power cords have not been safety tested at the factory and may not be used to power the unit For a replacement power cord contact your dealer e Slots and openings in the cabinet and the sides are provided for ventilation to ensure reliable operation of the unit and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This unit should not be placed in a built in in stallation or enclosure unless proper ventilation is provided e The maximum recommended ambient temperature for this equipment is 40 C e When using the unit in a multi unit rack assembly or closed assembly the ambient temperature inside the assembly may not succeed the maximum rated ambient temperature We advice to keep a distance of one U between a HYDRA COMPACT TWIN and another device in the rack for reasons of cooling e When installed in a rack the installation should be such that the amount of air flow required for safe opera tion of the equipment is not compromised The mounting of the equipment should be such that no hazardous condition is achieved due to uneven mechanical loading Reliable earthing of the equipment mounted in the rack should be maintained
66. through the power distribution in the rack Observe that the total of the ampere ratings on the rating plates of the equipment in the rack does not overload the supply wiring of the rack 1 3 5 Servicing Mechanical or electrical modifications others than described in this manual must not be made to the devices Barco is not liable for damages resulting from modified devices only authorized personnel should carry out other maintenance work not explicitly mentioned in this installation manual Never open the case of HYyDRA COMPACT TWIN without first disconnecting the power supply cords Measurements and tests with the opened device may be carried out only in the factory or by specially trained personnel due to the dangers of electrical shock 1 3 6 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners See sec tion 5 2 Cleaning for a cleaning instruction 1 3 7 Re packing Keep the original shipping carton and packing material they will come in handy if you ever have to ship your unit For maximum protection repack your set as it was originally packed at the factory Barco Hydra Compact Twin R59770027 Revision 13 February 2007 1 6 1 Introduction 1 4 Online documentation On the iSrupio Manuals amp Supplement CD ROM R5976593 this manual R59770027 as well as the iStupio user s manual R5976569 can be found in electronically form Insert the CD in the
67. ughter board unbalanced spare DVI DVI digital output card with scaling for HYDRA spare DVI DVI digital analog output card for HYDRA spare DVI DVI digital output card for HYDRA spare DVI video output card for HYDRA spare overlay input card OVL IPU 4 spare single board computer 2 spare CD ROM drive spare flash disk 256MB spare SCSI 4 cable spare power supply for HYDRA COMPACT TWIN R9830962 6 Technical appendix 6 15 6 Technical appendix Software Licenses R32875211 spare software medium iSrupio Hydra boot CD ROPT1934 iStupIo software license per HYDRA COMPACT TWIN ROPT1935 license for embedded audio metering per input channel Table 6 15 Order codes Barco Hydra Compact Twin R59770027 Revision 13 February 2007 6 16 7 Troubleshooting 7 Troubleshooting Check this chapter for help if your HYDRA COMPACT TWIN does not operate properly and for information how to contact the technical support of Barco Barco Hydra Compact Twin R59770027 Revision 13 February 2007 7 1 7 1 Hydra Compact Twin does not start up 7 Troubleshooting If HYDRA COMPACT TWIN does not start up check the power cables at the back side of HYDRA COMPACT TWIN When you hear no buzzer alarm and all green LEDs 37 of the power modules at the back are activated place the iSrupio Hydra boot CD in the drive 6 and restart if necessary 7 2 Hotline Feel free to contact us if you have any further questions e Barco N

Download Pdf Manuals

Related Search

Related Contents

  Manual de uso de la aplicación - Concurso Docente  User`s Manual  Manuel d`utilisation du moniteur VGA TruVision GEL 17 po./ 19 po.  Da-Lite Designer Manual - Veneer Concord Case 60" x 80", Video, Matte White  BEDIENUNGSANLEITUNG - CONRAD Produktinfo.  Model year 2014 USER MANUAL  FÖRTROLLA  GARIBALDI - Istituto Comprensivo IV Novembre di Mariano  Manual EYE-12 English Deutsch_neue Grafik_ohne  

Copyright © All rights reserved. Failed to retrieve file