User's Manual
Contents
1. KS 200KT Series Passive Detector With Autodial User s Manual KARASSN SECURITY PROTECTION ELECTRONICS CO LID Introduction KS 200KT Series telephone alarm system adopts 8 bit single chip as a processing core It can intelligently identify the infrared signals sent by human body When someone enters into the defense area the built in dialer will automatically dial the alarm informed telephone or pager number Therefore it is suitable for warehouse banks museums archives families markets etc Functions Description Low wrong alarm rate adopting processing technology of integrating dual infrared sensors and chips for double intellectualized signal and processing automatic temperature compensation With automatic dialer the system can dial 5 groups alarm phones or pagers and 4 groups urgent phones or pagers to ask for help Compatible with DTMF Double Tone Multi Frequency and pulse dialing With dialing pause function it can be used for exchange station elt adopts to learn coding between detectors remote manipulators and alarm host 4 digitals pin can be modified With a high decibel built in siren which promptly alarms on the site and guards against theft Leaving time delay defense time can be set Wireless remote control which can realize defense activation defense deactivation and first aid 6 remote controls and 7 detectors at most can be optioned for the2. to delete coding of the fifth detector Press 25 to delete coding of the sixth detector Press 26 to delete coding of the seven detector After the remote control or detector emitting there will be a beep Means the coding match have been successful e g If the users want to learn a coding of detector And learn a coding of door sensor Please well connect system and power on Hold on the receiver to press 12 48 There will be a beep Press 20 and there will be a beep Touch the detector to make a emission If there is a beep the coding match will be successful Continue to press 21 and there is beep Touch the door sensor to make an emission If there is a beep the coding match will be successful Press reset switch to exit setup Note Every defense area can learn one coding of detector at And every defense area has different coding Or it will take mistake After the coding match it is recommended to have a check Technical specifications Voltage AC220V 50Hz 60Hz Detective pre heat 60 seconds Phone number 9 groups Detective Distance 6 12m Detective angle 120 X 35 Alarm Loudness 100dB Remote distance 100m in Champaign Wireless Receiving Frequency 315 MHz KARASSN SECURITY PROTECTION ELECTRONICS C0 LTD ADD DongM i Guangming Industry Building Fengze District Quanzhou Fujian china TEL 86 0595 2575739 2575742 FAX 86 0595 2575752 E mil karassn pub
3. system Installation Requirements 1 The infrared detector has the highest sensitivity when a human body moves parallelly with the mirror surface and the sensitivity is the lowest when a human body moves vertically against the mirror As a result the angle and height against the horizontal surface should be noted during installation which will greatly affect the range of the defense area The 2 installation height and angle are shown as the following illustration W ndows 2 Mter y Door 2 Stand off from warm or cold sources e g warm air or cold air outlet air conditioning outlet electric radiators air cooling machines and etc Stand off from the windows 3 There should be no barrier within the defended area of a detector Operation Operation Guide 1 Component Descriptions Program switch normally the program switch GA BEE Phone for Phone setup is pressed in it springs out to program Activation Deactivation indicator the indicator will be on when the system is in activation state and it will be off when the system is in deactivation state DC input DC 12V 13 8V as backup power Polarity AC input input AC15V 50Hz or 60Hz Phone line input Built in siren output 4 levels of alarm sound for option Infrared detective sensitivity It has 3 levels for option Move the jumper from H position to L the sensitivity will gra
4. alarm in the locale 4 to on site monitor 0 to quit the state of alarm receiving If there is no operation in 5 seconds the alarm host will automatically hang up the telephone call then continue to dial another alarm informing phone number in three loops 5 Programming and Operation Note The telephone used to program should be DTMF Double Tone Multi Frequency phone Please turn the P T switch to T And the telephone should not be connected with the local telephone company The host should be in the state of defense deactivation during setup operation to against triggering alarm signal Every step has indicative sound A short beep shows the operation is effective A long beep shows the operation is ineffective When the system enters into the state of alarm setup the telephone is powered by the alarm host yet the current electricity is limited If you use the hands free function to set alarm you may fail or hear no sound Therefore you d better use the handset to set alarm Programming Operation Please take off the local telephone line and connect it by telephone machine Press program switch to spring up the jumper After a long beep then press AAAA A beep shows the system has enter into the state of setup AAAA stands for the user s code and the original code is 0000 Note All the following operations should be done in the setup state when all operations ar
5. dually decrease Alarm indicator while power on the alarm indicator will flash for a 60 seconds for pre heat After that it will be off While the alarm occurs the indicator will be on Socket for backup battery Monitor receiver Power on off Line in Proof break It will alarm and dial the urgent phone number or pager when it is open or breaked 2 The sound of cue When the system is powered on there will be a beep which indicates the system is normal and in the state of defense activation A long beep at 15 second interval shows the system is in low voltage state During leaving time there will be a long beep every one second The users should 3 5 immediately leave the defense area 3 Operation of the Remote Control Activation press key to activate and there will be a short beep and the indicator will be on Deactivation press fl key to deactivate and there will be a tow beeps The indicator will be off Urgent alarm press o key to enter into urgent alarm state and the system will automatically dial urgent phones for first aid 4 Alarm Receiving Operation Note this function should only be suitable for DTMF telecom system When you receive the alarm phone call you can pick up the handset then hear alarm sound which will last for 5 to 25 seconds After the sound you can press as following 2 to clean the alarm 3 to open the
6. e finished the program switch should be turned to OFF 1 User s Code Modification Press 9 AAAA BBBB BBBB AAAA is for the user s code the original one is 0000 BBBB is four the new code After the Code modification the old code will be invalid If you want to program again you should enter the new code 2 Setup informed phone numbers Press 10 CCCCC to set the first group of 6 7 8 informed phone or pager number Press 11 CCCCC to set the second group Press 124 CCCCC to set the third group Press 134 CCCCC to set the forth group Press 14 CCCCC to set the fifth group Press 15 CCCCC to set the first group of urgent phone or pager number Press 16 CCCCC to set the second group Press 17 CCCCC to set the third group Press 18 CCCCC to set the forth group CCCCC stands for the phone pager or mobile number Note During the course of entering the telephone number mobile phone pager use as a pause for two seconds The number of is subject to the type of telephone exchange e g mobile phone group telephone semi automatic pager station etc Each group of number including should not beyond 16 digits Add after phone number mobile or call number means the phone number is adopted by pulse dial model instead of DTMF Every phone number including is 16 digitals at most Have to dial the before pager number It is
7. lic qz fj cn V bsite http www karassn com 5 g 17
8. not necessary to input unwanted phone numbers of nine It can directly cover with or delete it to re input if the users has input wrong information During alarm the host will dial the phones three times from the first one to the ninth circularly As for the processed phones the host will not dial any more For example if you want to set the following groups of telephone number 1234567 dialed by DTMF 7654321 dialed by pulse The main engine 1234567 extension 801 by DTMF The first group of urgent telephone 13900000012 dialed by DTMF The second group of urgent pager number1297615325 the code name is 110 dialed by DTMF You can press as following 10 1234567 11 7654321 12 1234567 801 15 13900000012 16 12876115325 1 110 Form of an automatic page station for reference only 3 Informed Phone Numbers Deletion Press 10 to delete the first group of phone or pager number Press 11 to delete the second group Press 12 to delete the third group Press 13 to delete the forth group Press 14 to delete the fifth group Press 15 to delete the first group of urgent phone or pager number Press 16 to delete the second group Press 17 to delete the third group Press 18 to delete the forth group Press 19 to delete all numbers 9 10 11 4 Choices of the Volume of Alarm Sound Press 24 to choose the minimum of the volume of the alarm sound Press 25 to choose the moderation of
9. s 14 to learn the coding of the fifth one Press 15 to learn the coding of the sixth one Press 10 to delete the coding of the first remote control Press 11 to delete the coding of the second one Press 12 to delete the coding of the third one Press 13 to delete the coding of the forth one Press 14 to delete the coding of the fifth one Press 15 to delete the coding of the sixth one Press 20 to learn the coding of the first detector There is a emission after a sound indication Press 21 to learn the coding of the second detector There is a emission after a sound indication Press 22 to learn the coding of the third 12 13 14 detector There is a emission after a sound indication Press 23 to learn the coding of the forth detector There is a emission after a sound indication Press 24 to learn the coding of the fifth detector There is a emission after a sound indication Press 25 to learn the coding of the sixth detector There is a emission after a sound indication Press 26 to learn the coding of the seventh detector There is a emission after a sound indication Press 20 to delete the coding of the first detector Press 21 to delete the coding of the second detector Press 22 to delete the coding of the third detector Press 23 to delete coding of the forth detector Press 24
10. the volume ofthe alarm sound Press 26 to choose the high volume of the alarm sound Press 27 to choose the maximum of the volume of the alarm sound 5 Setup of mute alarm Press 28 to shut set mute alarm on the site It will dial the informed phone numbers if the alarm occurs The sound of the indications of the remote control operation the warning of telephone line broken and of low backup power voltage can be normally heard 6 Setup Leaving Time Press 35 DD the above DD refers to leave time delay defense time 00 99 seconds It should be two digits The alarm host will give out a short beep every one second and the users have to leave during the leaving time 7 The default from factory User code 0000 Informed phone number no Alarm sound switch open Volume of alarm Maximum Leaving time 00 Coding Operation It can be learned by 6 remote controls and 7 detectors including door sensor and smog sensor at most Please take off the local telephone line and connect the line of telephone machine Press program switch to spring out the jumper There will be a indicative beep And hold on the receiver to press 12 48 and there will be a indicative beep again Then enter into following Press 10 to learn the coding of the first remote control Press 11 to learn the coding of the second one Press 12 to learn the coding of the third one Press 13 to learn the coding of the forth one Pres
Download Pdf Manuals
Related Search