POS88Ⅳ Line Thermal Printer User's Manual Beijing Spirit
Contents
1. ESC D Set horizontal tab positions ESC E Turn emphasized mode on off ESC G Turn double strike mode on off ESC J Print and feed paper ESC L Select page mode ESC M Select character font ESC S Select standard mode ESCT Select print direction in page mode ESC V Turn 90 clockwise rotation mode on off ESC W Set printing area in page mode ESC Set relative print position ESC a Select justification ESC c 0 Select paper type ESC c3 Select paper sensor s to output paper end signals ESC c 4 Select paper sensor s to stop printing ESC c 5 Enable disable panel buttons ESC d Print and feed n lines ESC p General pulse ESCt Select character code table ESC Turn upside down printing mode on off FSg1 Write to user NV memory FS g2 Read from user NV memory FS p Print NV bit image FS q Define NV bit image GS FF Black mark paper localization GS Select character size GS Set absolute vertical print position in page mode GS Define downloaded bit image GS Execute test print GS Print downloaded bit image GS Start end macro definition GS B Turn white black reverse printing mode on off GS H Select printing position of HRI characters GS I Transmit printer ID GS L Set left margin GS P Set horizontal and vertical motion units GS V Cut paper GS W Set printing area width GS Set relative vertical print position in page mode Ignored2. GS Execute macro GS a Enable disable Automatic Status Back ASB GS b Turn smoothing mode on off GS f Select font for HRI characters GS h Set bar code height GS k Print bar code GS r Transmit status GS v 0 Print raster bit image GS w Set bar code width FS Set print mode s for Chinese characters FS amp Select Chinese character mode FS Turn underline mode on off for Chinese characters FS Cancel Chinese character mode FS 2 Define user defined Chinese characters FSS Set left and right side Chinese character spacing FS W Turn quadruple size mode on off for Chinese characters Detailed command description please refer to POSSSIV Control Commands Appendix Index of Print Characters
3. 3 00 H mm e GB GB2312 80 Chinese 24x24 dots 3 00 W x3 00 H mm 1 4 Interface e Serial interface DB 25 socket female supports XON XOFF and RTS CTS protocols Baud rate 12000 115200bps adjustable Data structure Istart bit 7 or 8 data bits 1 stop bit Parity checking no parity or odd even parity optional e Parallel interface DB 25 socket male or 36 pin is optional 8 bit parallel interface BUSY ACK handshaking protocol TTL signal level e Cash drawer control DC24V 1A 6 pin RJ 11 socket 1 5 Print control commands e Character print commands support double width double height print of ANK characters user defined characters and Chinese characters the character line spacing is adjustable e Graphics print commands support the print of bit map graphics and download bit map graphics with different density e GS bar code print commands support UPC A UPC C EAN 13 EAN 8 CODE39 ITF CODEBAR CODE93 CODE128 bar code print 1 6 Power Supply e DC24V 10 2A A 1009 3P power socket 1 7 Operation Environment e Operation temperature 5 50 C Relative humidity 10 80 e Storage temperature 20 60 C Relative humidity 10 90 C 1 8 Outline Dimension e 150 CW x192 L x150 H mm 1 9 Model classification Model Cutter Interface POS88IV AS Partial cutting Serial DB25 female POS88IV API Partial cutting Parallel 36 pin standard print POS88IV AP2 Partial cutting Parallel DB25 male
4. POS88IV BS Full cutting Serial DB25 female POS88IV BP1 Full cutting Parallel 36 pin standard print POS88IV BP2 Full cutting Parallel DB25 male Chapter 2 Operation Specification 2 1 Printer Appearance Power Indicator VEG l Status Indicator red F ae Paper end Indicator red Paper Feed Button feed Paper out Slot Power Switch Printer interface Cash drawer interface Power socket Fig 2 1 printer appearance 2 2 Paper Installation 2 2 1 Paper Loading POS88IV adopts 80mm width thermal paper roll If you prepare to load the paper you can do as the following steps Hold down the upper cover button open the movable upper cover move away the old paper roll and put the new thermal paper in the paper holder of printer draw a certain length of the paper roll put the paper end on the print head close the upper cover and press it downwards lightly until it restore to original position and the paper end appears from the paper out slot which is on the upper cover then print paper installation is finished Caution 1 When there is no paper in the print head don t press FEED button avoiding to shorten the print head life 2 Please don t feed or draw the paper forwards or backwards with hands When returning paper please cut the extra paper and press LF button paper will go forwards 2 2 2 Solution to Paper Jam Turn power
5. 13 SEL Out Pulling up to HIGH level signal by a resistor LOW level signal indicates ee ERE Ont that there has error 14 15 17 18 34 36 NC No connection oe GND Grounding logical 0 level Note 1 In denotes input to the printer Out denotes output from the printer 2 Signal level is TTL standard Fig 2 7 Pin assignment of 36pin parallel interface The timing chart for interface signal of parallel interface is as Fig 2 8 shows BUSY ACK DATA STB 2 3 3 Cash Drawer Interface The cash drawer interface of POS POS88IV adopts RJ 11 6 pin socket as Fig 2 9 shows Fig 2 9 Cash drawer interface The pin assignment of the cash drawer interface is defined as follows Pin No Signal Direction l Chassis Ground 2 Cash drawer driver signal Out 3 Cash drawer on off status signal In 4 24VDC Out 5 N C 6 Cash drawer on off status signal ground 2 3 4 Power Connection POS88IV uses the external power supply adopter as 24V 10 2A power socket is A 1009 3P model Fig 2 10 Power Socket as Fig 2 10 shows 2 4 Buttons and Indicators There is one button and three indicators on POS88IV printer FEED is paper feeding button the function of its enabling or disabling the button on off can be set by print command when the button is enabled press FEED button then the paper presenting driver starts up and paper fed into the printer release FEE
6. D button paper feeding stops The green POWER light is the power indicator red ERROR light is status indicator it is dark when the printer works normally while it flashes when reporting an abnormal emergency as the following form shows ERROR Error Indicator Status Description Code HEX Paper out Indicator blinks Print head uplift Buzzer rings Put down print head Print head Buzzer rings and Recovers automatically overheat indicator blinks when bu pant head Impossible to recover check if there is paper jam Auto cutter Buzzer rings and Position Error indicator blinks When any error shown above occurs different status and data will be returned according to different printing commands 2 5 Self test The self test will check the condition of printer if the printer prints out the self test receipt correctly it means the printer works normally Otherwise it needs to repair The self test will print out the firmware version interface setting and 128 ANK characters Hold down FEED button and turn on the power then release the button self test begins automatically at this moment 2 6 DIP Switch Setting DIP Switchl is used to set the baud rate and data structure of serial interface setting is as the following tab shows Serial Interface SW Function ON OFF 1 1 Data reception error Ignored Print 1 2 Receive buffer capa
7. IV can be connected to standard RS 232CRS 232C interface When it is connected to IBM PC or its compatible machine connection can accord to Fig 2 4 DSR 6 6 DSR DSR 6 6 DSR GND 4 enD H s N 5D 5N 7 GND RTS RTS 3 8 CTs 3 5 CTS TXD TXD 1 DCD 27 8 DCD RXD RXD 2 RXD 3 RXD 3 TXD 2 TXD Printer IBM PC Serial Printer IBM PC Serial 25PIN Socket Interface DB 9 25PIN Socket Interface DB 25 Fig 2 4 Connection between POS88IV and IBM PC Serial Interface Sketch Map 2 3 2 Parallel Interface The parallel interface of POS88 IV printer is compatible with CENTRONICS supports BUSY or ACK handshaking protocol uses DB25 socket male or 36pin CENIRONICS socket female optional The pin order of parallel port is as Fig 2 5 shows 13 NN 900000920000400 rd tn ge S 25 14 Fig 2 5 Pin Order of Parallel Port The pin assignment of DB25 parallel interface is shown in Fig 2 6 shows Pin No Signal Direction Description Strobe pulse to latch data ISTE P Reading occurs at falling edge DATA a These signals represent the 1 3 DATA2 In ing bit to 8 bit of the parallel data 4 DATA3 In 5 DATA4 In representatively each signal is at HIGH level when data is 6 PATAS ut logic 1 and LOW when data is 7 DATA6 In Kr ika 8 DATA7 In ii 9 DATA8 In Answer pulse LOW level signal in
8. POSS88 V Line Thermal Printer User s Manual Beijing Spirit Technology Development Co Ltd Content Introduction ent eee 3 Chapter 1 Feature and Performance neneennnenenenzznenenzjnenzjnnz 4 1 1 Print Performance neennenennnzenennnzenenezzennranzennnzn 4 1 2 Print Papersssemnnnnnnnensnnnnnznnnenzznzntizznznzntirinzntntinzntnzai 4 1 3 Print Font ee 4 1 4 Interface teeeeeeeeeereeeeeeerseereresereresereresereresereseseresesereseeereseeeee 4 1 5 Print Control Command seen nn n en en nn ran n nanna 5 1 6 Power Supply sesmsnneeneeenezznznnznzzzjonnzznznzznznzztinzazzati 5 1 7 Operation Environment eee 5 1 8 Outline Dimension verre teeter eee e eee ew eee eee 5 1 9 Model Classification eee 5 Chapter 2 Operation Specification E A A TT 6 2 1 Printer Appearance E T 6 2 2 Paper Installation eter treet teeter eet tenes 6 2 2 1 Paper Loading meseneensnennzonttinznzntitznzntttitznnzti 6 2 2 2 Solution to Paper Jam i eeenennenenenn en er ern e net r tenni n ten 7 2 3 Interface Connection verre eee eet rent 7 2 3 1 Serial Interface wee J 2 3 2 Parallel Interface arr ee g 2 3 3 Cash drawer Interface nennneneeenenennenenenezzennzi 11 2 3 4 Power Connection eeeneeeeeeessnnnzzznzzzzznnzzzznzzznnnnznnz 11 2 4 Buttons and Indicators scence ees 11 2 5 Self test bjetefeiutu fa fe e feta ffe ta aa a ffe f ff f 12 2 6 DIP Switch Setting ETT TITTI IT sees sais e s REE ssa sos 12 Chapter 3 Command List smeensenennzzonttitintatttitinzatttnti 14 Append
9. Y receive buffer capacity receive buffer capacity condition If is 138 bytes change is 256 bytes change data buffer BUSY condition BUSY condition capacity set to AKB 2 6 Reserved Do not change settings 2 7 2 8 On 0x0d enabled Table A Print density Low power consumption SW 2 3 SW 2 4 Low power consumption mode ON ON 1 Normal density OFF OFF 2 Medium density ON OFF 3 High density OFF ON When set DIP switch it needs to open the small iron plate at the bottom of the printer Chapter 3 Command List Command Name HT Horizontal tab LF Print and line feed FF Print and return to standard mode in page mode CR Print and carriage return CAN Cancel print data in page mode DLE EOT Real time status transmission DLE ENQ Real time request to printer DLE DC4 Generate pulse at real time ESC FF Print data in page mode ESC SP Set right side character spacing ESC Select print mode s ESC Set absolute print position ESC Select cancel user defined character set ESC amp Define user defined characters ESC Select bit image mode ESC Turn underline mode on off ESC 2 Select default line spacing ESC 3 Set line spacing ESC Select peripheral device ESC Cancel user defined characters ESC Initialize printer
10. city 45 bytes 4K bytes 1 3 Handshaking XON XOFF DTR DSR 1 4 Word length 7 bits 8 bits 1 5 Parity check Enabled Disabled 1 6 Parity selection Even Odd 1 7 Transmission speed refer to the following table 1 8 Transmission speed bps 1 7 1 8 38400 ON JON 4800 OFF ON 9600 ON OFF 19200 OFF OFF SW Function ON OFF 2 1 Handshaking Receive buffer full Off line or receive BUSY condition buffer full 2 2 Reserved Do not change settings 2 3 Print density Refer to Table A 2 4 Low power consumption 2 5 Change receive When the remaining When the buffer BUSY receive buffer remaining receive condition If data capacity is 138 buffer capacity is buffer capacity set bytes change 256 bytes change to 4KB BUSY condition BUSY condition 2 6 Reserved Do not change settings 27 2 8 0D print Enabled Disabled Parallel Interface SW Function ON OFF 1 1 Go along automatically Enabled Disabled 1 2 Receive buffer capacity 45 bytes 4K bytes 1 3 1 8 Undefined SW Function ON OFF 2 1 Handshaking Receive buffer full Off line or receive BUSY buffer full condition 7 0 Reserved Do not change settings 2 3 Print densitv Refer to Table A 2 4 Low power consumption 2 5 Change receive When the remaining When the remaining buffer BUS
11. dicates that data have 10 ACK Out already been received and the printer gets ready to receive the next data HIGH level signal indicates that 11 BUSY Out the printer is BUSY and can not receive data 12 PE Out HIGH level signal indicates that paper is end 3 SEL Out Pulling up to HIGH level signal by a resistor 15 JERR Out LOW level signal indicates that there has error 14 16 17 NC No connection 18 25 GND Grounding logical 0 level Note 1 In denotes input to the printer Out denotes output from the printer 2 Signal level is TTL standard Fig 2 6 Pin assignment of DB 25 parallel interface The pin assignment of 36pin parallel interface is as Fig 2 7 shows pin No Signal Direction Description Strobe pulse to latch data l STB In Reading occurs at falling edge para ali These signals represent the 1 3 DATA2 In TE bit to 8 bit of the parallel 4 DATA3 In data representativelv each 5 DATA4 In signal is at HIGH level when 6 DATAS In data is logic 1 and LOW 7 DAS n hen data is logic 0 8 DATA7 In ka e 9 DATAS In Answer pulse LOW level signal indicates that data have 10 ACK Out already been received and the printer gets ready to receive the next data HIGH level signal indicates 11 BUSY Out that the printer is BUSY and can not receive data HIGH level signal indicates a ou that paper running out
12. ix Index of Print Characters EEE 16 Introduction POS88IV printer is a new type line thermal printer it features in fast speed print low print noise high reliability perfect print quality and ribbon needless avoiding the vexation of regular maintenance POS88IV printer small in outline dimension simple operation and extensive application especially suitable for commercial cash register PC POS bank POS and all kinds of receipts print Chapter 1 Feature and Performance 1 1 Print Performance Print method direct thermal Print paper width 79 5 0 5mm Print density 8 dots mm 576 dots line Print speed approx 180mm sec or 48 lines sec Reliability Print head life 100km Using condition Print 12 x 24 ASCII characters print 50 lines each time intermittent print repeatedly Each dot line printing at the same time should not exceed 25 each character line and one dot vertical printing repeatedly should not exceed 11 times Use specified thermal paper Cutter life 500 000 cuts Using condition less than 30 cuts minute Valid print width 72mm Feeding speed approx 180mm sec or 48 lines sec 1 2 Print Paper e Thermal paper roll model TFSOKS E Japan paper co ltd AF50KS E JUJO THERMAL e Thermal paper roll Width 79 5 0 5mm Outer Diameter 80mm max Inner Diameter 13mm min Thickness 53 60g m 1 3 Print Font e IBM Character set II ANK 12x24 dots 1 25 W
13. off open the upper cover hold down the black rubber cutter lever at the same time move the cutter forwards slowly can separate the cutter from the print head Then lift the print head lever forwards to maximum position draw out the paper slowly with hand 2 3 Interface 2 3 1 Serial Interface The serial interface of POS88IV printer is compatible with RS 232C supports RTS CTS and XON XOFF handshaking protocols uses DB25 socket female The pin order of the serial port is as Fig 2 2 shows 13 1 ay 25 14 Fig 2 2 Pin Order of Serial Port The pin assignment of serial interface is shown in Fig 2 3 Pin Signal Source Description No Name 2 RXD Host Printer receives data from host 3 TXD Printer Printer transmits control code X ON X OFF and data to host 5 CTS Printer Signal MARK indicates that the printer is BUSY and unable to receive data SPACE indicates that the printer is READY for receiving data 6 DSR Printer Signal SPACE indicates that the printer is ONLINE 7 GND Signal Ground 8 DCD Printer Same to signal CTS Note Source denotes the source that signal come from 2 Logical signal level is EIA Fig 2 3 Pin Assignment of Serial Interface The baud rate and data structure in serial interface mode is 9600bps 8 bit data bits no parity bit and 1 stop bit The serial interface of POS88
Download Pdf Manuals
Related Search