User Manual IS 6132 rev O
Contents
1. 13 General guidelines 13 Typical schematics 14 Appendix eee eere rennen nnn 15 Language 15 Technical Specifications 16 System Specification 16 Connection Details 17 17 User Manual IS 6132 O docx DIS Digital Conference System Important Installation precautions Do not install the unit in a location near heat sources such as radiators or air ducts or in a place exposed to direct sunlight excessive dust or humidity mechanical vibration or shock Compliance The equipment is intended to be used in professional audio applications Note This device is not intended to be connected directly to a public internet network EMC conformance to Environment E2 Commercial and Light Industrial Testing is based on the use of supplied and recommended cable types The use of other than shielded screened cable types may degrade EMC performance Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada2. DIS GM 61xx series only Headphone output level 1 5 V Min headphone impedance 4 ohm 1 kohm External loudspeaker output level balanced max 2 8 V Min loudspeaker amp input impedance 2 kohm Frequency 125 15kHz Signal to noise ratio gt 85 dBA Total harmonic distortion lt 0 1 General Power 24 48 V DC Power consumption excl LS6032P 2 5W maximum User Manual Sg AGREE SS 22 KR rg ses kes sh Technical Specifications Power supplied from CU 61xx EX 6010 PS 6000 Temperature to guarantee specified performance 5 Deg 40 Deg 10 to 80 humidity Storage temperature Weights saan 1 0 kg Dimensions W x H x D 235 x 73 x 115 mm without knobs and microphone Connectors DCS LAN loop through 2 pieces RJ45 Microphone input XLR3 female socket Headphone connectors 2 pieces mini jack 3 5 mm yqa Qa AAEE qaqaia qay 1 piece standard jack 1 4 Headset connector 8 pin DIN socket LS 6032P Loudspeaker Unit socket D9S Specifications are subject to change without notice 16 DCS 6000 Digital Confere
3. Crestron e Functionality on the CU 61xx depends on the Feature License uploaded into the unit e Firmware in Delegate units Interpreter Units Central Units etc is upgradeable e Operated either stand alone or from a PC using the CU browser or using SW 6000 software e Added functionality and comprehensive features provided by SW 6000 software package running on PC The SW 6000 is an optional software package which expands the functionality of the DCS 6000 system The software runs on standard computer technology Standard PC with Windows 7 Server 2008 etc Main features of the SW 6000 are e Microphone management e Mimic panel operation e Interpretation management e Voting management e Message handling e Agenda handling e Data stored on SQL data base e Web service interface available for easy links to external applications e Multi language user interfaces e Supports different User types with different priorities user interfaces control possibilities DCS 6000 Digital Conference System System components Central equipment etc CU 6105 Central Unit CU 6110 Central Unit EX 6010 Extension Unit PS 6001 DCS LAN Power Kit consisting of one PS CU and one PI 6000 PS CU Power Supply PI 6000 DCS LAN Power Inserter RC 6000 Redundancy Controller AO 6004 Audio Output Unit AO 6008 Audio Output Unit RP 6004 Repeater for four chains JB 6104 Junction Box with 4 outputs SZ 6104 DCS LAN Switch
4. Authorized under the verification provision of FCC Part 15B Please follow your regional recycling scheme for batteries packaging and electronic waste Information to the user This equipment has been tested and found to comply with the limits for a Class B digital device Cleaning To keep the cabinet in its original condition periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly User Manual To avoid moisture condensations do not install the unit where the temperature may rise rapidly pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment to an outlet on a circuit different from that to which the e receiver is connected
5. Corsican COR Croatian SCR Czech CZE Danish DAN Dutch DUT English ENG Estonian EST Finnish FIN French FRE Gallegan GLG Georgian GEO German GER Greek GRE Hausa HAU Hebrew HEB Hindi HIN Hungarian HUN Language ISO 639 2 B abbreviation Icelandic ICE Indonesian IND Irish GLE Italian ITA Japanese JAP Javanese JAV Kazakh KAZ Khmer KHA Kirghiz KIR Korean KOR Kurdish KUR Lao LAO Latvian LAV Lithuanian LIT Macedonian MAC Malay MAY Maltese MAL Marathi MAR Mongolian MON Nepali NEP Norwegian NOR Panjabi PAN Persian PER Polish POL Portuguese POR Raetoroman ROH Romanian RUM Russian RUS Serbian SCC Sinhalese SIN Slovak SLO Language ISO 639 2 B abbreviation Slovenian SLV Spanish SPA Swahili SWA Swedish SWE Tagalog TGL Tajik TGK Tamil TAM Telugu TEL Thai THA Tibetan TIB Turkish TUR Turkmen TUK Ukrainian UKR Urdu URD Uzbek UZB Vietnamese VIE Welsh WEL Yoruba YOR Other no 1 1 Other 2 2 Other 3 3 Other 4 4 Other 5 5 Other 6 6 Other 7 7 Other 8 8 Other 9 9 Other 10 N10 Other no 11 Nil Other no 12 N12 15 DCS 6000 Digital Conference System System Specification Digital Section Sound quality 20 bit audio 32 kHz sampling frequency Number of incoming channels 32 31 floor Number of outgoing channels interpreted 31 Analog Section Microphone input type
6. e Consult the dealer or an experienced radio TV technician for help dampened with a mild detergent solution Never use organic solvents such as thinners or abrasive cleaners since these will damage the cabinet DIS Digital Conference System Repacking Save the original shipping cardboard box and packing material they will become handy if you ever have to ship the unit For maximum protection Warranty The individual units in the DCS 6000 system are minimum covered by 24 months warranty against defects in materials or workmanship User Manual re pack the unit as originally packed from the factory DCS 6000 Digital Conference System User Manual Your DCS 6000 Conference System The DCS 6000 system DCS 6000 Digital Conference System is a system to be used at meetings where a number of people are addressing the Floor in structured manor audio from the Conference units can be heard in the built in loudspeakers in the units The system does also allow for simultaneous interpretation for international conferences where multiple languages are used To enable all participants to understand the proceedings interpreters can simultaneously translate the speaker s language as required These interpretations distributed through the connected Conference units and delegates can select the language of their choice and listen to it through headphones DCS 6000 Digital Conference System comprises of
7. the Booth number has not been set up For setting up the interpreter set please see the section Set up for each interpreters set Selection of incoming language When interpreting the interpreter will listen to either the Floor language or will listen to one of the interpreted languages The Floor button will select the Floor language and the buttons a b c and d select the pre selected languages shown on the LCD display to the headphone output Each of the buttons can be pre selected to any of the interpreter channels When one of the buttons a b c and d is pressed a LED is lighted in the button pressed indicating that this pre select is chosen The two first characters in the display show the channel number e g 12 or 5 and the following three characters show the corresponding language in short see language list When the Floor button is pressed the Floor channel is selected and the green Floor LED is lit Also the indication in one of the buttons a b c and d is removed OBS If the functionality that pressing the Floor button again shall switch the listening back to the previous selection of a b c or d is required at setting in the CU 61xx can be changed Please consult the DIS factory for this option When one of the a d channels is selected the Floor LED goes out and the audio from the selected channel is switched on instead of Floor It is then possible to change the listening channel with the R
8. 10 m Loudspeaker Pin Connector D9S 1 Power 48VDC 2 Not connected 3 Signal 4 Not connected 5 Power Ground 6 Mute 7 Not connected 8 Signal 9 Signal Ground Interpreter Headset Pin Connector Din 8 pole female 1 Headphones 2 0 V Ground 3 Mic signal 4 Headphones 5 Mic signal 0 V Ground 6 0 V Ground 7 0 V Ground 8 0 6001 20 5 Connection Cable 20 6001 50 Connection Cable 50 m DA 6021 2 Headset GM 6523 Gooseneck microphone 40 cm GM 65XX WS 4 Wind screen for GM 65xx 17 SHURE LEGENDARY PERFORMANCE www shure com United States Canada Latin America Caribbean Shure Incorporated 5800 West Touhy Avenue Niles IL 60714 4608 USA Phone 1 847 600 2000 Fax 1 847 600 1212 USA Fax 1 847 600 6446 Email info shure com Europe Middle East Africa Shure Europe Gmbh Jakob Dieffenbacher Str 12 75031 Eppingen Germany Phone 49 0 7262 9249 100 Fax 49 0 7262 9249 114 Email info shure de Asia Pacific Shure Asia Limited 22 F 625 King s Road North Point Island East Hong Kong Phone 852 Fax 852 2893 4055 Email info shure com hk 2893 4290
9. For detailed instruction in how to use the above units please refer to the User Manuals for the relevant products DCS 6000 Digital Conference System Operating instructions IS 6132 P Interpreter Unit General description The IS 6132 Interpreter Unit is designed for use for one interpreter It is a compact unit for table top use The design of the units is easy understandable with a listening part at the left side of the unit and a speaking part at the right side of the unit User Controls indications amp connectors Front plate layout Danish Interpretation Systems User Manual Features The main features of the IS 6132 Interpreter Unit are 4 pre select listening channels e Large LCD display with back possibility light e Clear LED indication in buttons e For use with either headset or gooseneck microphone IS 6132 Interpreter Set Speaking too fast 9 Incoming N VOLUME Front plate controls Incoming Section 1 Volume This control adjusts the listening connected headphone level in the 2 Bass This control adjust the Bass level in the connected headphone 3 Treble LJ LJ Microphone This control adjust the Treble level in the connected headphone 4 a b c d These button selects between four pre selection of relay channels 5 Relay select These buttons are used for each of the fou
10. SHURE LEGENDARY PERFORMANCE Conferencing and Discussion Systems IS 6132 Interpreter Unit USER GUIDE 2015 Shure Incorporated User Manual IS 6132 rev O docx DCS 6000 Digital Conference System Table of Contents Table of Contents 2 Important 3 Installation precautions 3 Compliance 3 Information to the user 3 Cleaning 3 Repacking 4 Warranty 4 Your DCS 6000 Conference System 5 The DCS 6000 system 5 System components 6 Central equipment 6 Interpreter equipment 6 Conference units and Ch selectors 6 ACCESS ONES wanaokaa ane 6 Operating instructions 7 2015 Shure Incorporated User Manual IS 6132 P Interpreter Unit 7 General description 7 Features cer Rer uwa Ern 7 User Controls indications amp connectors 7 Set up for each interpreters set 8 Normal Operation 10 System Setup
11. ct push buttons up and down if the B mode is set to All in the B language setup menu User Manual The B selection will only function when B is selected and the Microphone is not switched On Microphone on off When the push button is pressed the microphone audio is put on to the outgoing channel the LED s in the button and the lamp of the microphone are lit up If another interpreter already occupies the outgoing channel nothing will happen When the push button again is pressed the sound from the microphone the button LED s and microphone lamp is switched off Mute The button will switch off the audio from the microphone to the outgoing channel while it is depressed the channel is muted Also the light ring in the microphone is switched off while depressed When the button is released the microphone audio is switched on again and the light ring in the microphone is switched on Speaking too fast When pushing this button the LED in the Speaking too fast button lights in 10 sek in all IS 6132 units And at the same time the Speaking too fast indication will be indicated in units supporting this function as some CM6xxx units or PC with SW 6000 software Call Not implemented A Engaged The yellow LED is lit if the channel is occupied either by another interpreter or the interpreters set itself occupies the channel B Engaged The yellow LED is lit if the channel is occupied either by another in
12. e following menu will appear B language m7 Norwegian B mode Cancel One Press button c for selecting the B language for the Interpreter Unit A black dot is indicating the selection Use Relay select up down to scroll through the available languages Press button a for selecting the B mode for the Interpreter Unit The B mode selection has the following choices All The interpreter can select any B language himself One Only the B language chosen at the B language selection can be used during operation None During operation no B language can be used the B button has no function except for b B To save the selection press OK B button Ver and serial no This is an information menu showing the version software serial number and the address assigned to the unit by the CU 61xx Central Unit 156132 rev D SW ver 053 009 Serial 055 004 255 Address 21 3 Press to return to the Set up menu Communication status This is an information menu showing the communication status of the unit Errors 0 Retries 0 Tx dropped 0 DCS 6000 Digital Conference System Press Reset to reset the number of Errors etc counted After start up some errors can be seen but if the numbers of errors are constantly increasing the cabling or a unit is defective The fault could also be a LAN connector which is not properly inserted Please note the click from the lock when
13. elay select up and down push buttons When the highest number is reached when stepping up the counting restarts from 1 The reverse will happen when stepping down If one of the buttons is held down for more than one second the channels will scroll through the languages with a speed of 2 4 languages per second Only the number of channels set at the Channel Set up menu at the CU 61xx can be selected and shown The numbers will always be in succession from 1 and up The same is the case for the CS 6032 channel selectors with the exception that the CS 6032 is also showing channel 0 floor 10 DCS 6000 Digital Conference System Showing quality of Incoming language To the right of the four a d language abbreviations of the quality of the source is shown If there is no interpretation at the channel Floor audio is present then FLOOR will be shown When there is an interpreters set switched on to the channel where the interpreter is listening to Floor then a quality indication is shown When an interpreter s set is switched on to the channel where the interpreter listens to another channel whose interpreter listens to Floor a quality indication is shown This is indication one relay interpreting 4 Brought one level further a quality indication is shown This is indication for double or more relay interpreting When interpreting on the A language and the A language of the Interpreter Unit i
14. er Interpreter equipment IS 6132 P LS 6132 P Interpreter Unit Interpreter Loudspeaker Conference units and Ch selectors DC6990 P Conference Unit portable with touch screen with two built in channel selector Chip card and 5 voting buttons configurable as Delegate Dual Delegate or Chairman Conference Unit portable Conference Unit portable with two built in channel selectors DM 6680 P Conference Unit portable with voting CM DM 6080 F Conference Unit flush mounted with built in channel selectors DC 6120 P DC 6190 P DM 6620 F CM DM 6680 F MU 6040 C D 0 6042 D DV 6501 F AM 6040 CS 6340 FV H Accessories User Manual Conference Unit flush mounted with Chip card and 5 voting buttons Conference Unit flush mounted with built in channel selector Chip card and 5 voting buttons Microphone Unit for use with FD FC front plate with Loudspeaker Microphone and Buttons Available in Delegate D and Chairman C version Dual Microphone Unit for use with FD FC front plate with Loudspeaker Microphone and two delegate Buttons Voting Unit Ambient Microphone Unit Channel Selector flush mounted In addition to the unit a number of accessories are available like Storage Boxes GM 6523 Gooseneck Microphone 40 cm GM 6524 Gooseneck Microphone 50 cm GM 6525 Gooseneck Microphone 63 cm DH 6021 Delegate Headphone DH 6223 Stethoscope Headphone DH 6225 Ear Clip Headphone
15. h depends on have an internal termination the units connected and length of feeding cables etc 13 DCS 6000 Digital Conference System User Manual Typical schematics 8 channels TEES 8 channels 2 Digital Receivers Digital Transmitter IR Radiator Channel Selectors B B 6008 Output Unit 7 7 7 7 7 gt Delegate Delegate Delegate Delegate Delegate Delegate Delegate External systems External systems Conference Units Out A B C D E F G H DCS LAN 7 gt gt 7 7 gt 7 Chairman Delegate Delegate Delegate Delegate Delegate Delegate Central Unit Booth 1 Booth 2 LJ Loudspeaker es Loudspeaker lt Interpreter Interpreter Interpreter Interpreter Interpreter Interpreter 14 DCS 6000 Digital Conference System Appendix Language list The following languages are supported by the DCS 6000 system Language ISO 639 2 B abbreviation Floor language FLO User Manual Afrikaans AFR Albanian ALB Arabic ARA Armenian ARM Azerbaijani AZE Basque BAQ Belarusian BEL Bengali BEN Bulgarian BUL Burmese BUR Cantonese CAN Catalan CAT Chinese CHI
16. ill be disconnected automatically if a microphone is switched on at one of the interpreter sets in the same booth same A language This connector is only on some versions of the Interpreter Unit 19 DCS LAN connector Two RJ45 sockets are located at the bottom of the unit for connecting to the previous unit an Interpreter set or CU 61xx or another DCS 6000 unit and to the next unit Set up for each interpreters set When an IS 6132 interpreter unit is connected to the CU 61xx the following start up screen is shown DANISH INTERPRETATION SYSTEMS 156132 055 004 255 9 digit number at the bottom of the display is the units serial number Each of the three positions separated by dots can hold a value of 0 255 giving a maximum serial number of 255 255 255 DCS 6000 Digital Conference System After some seconds the following type of screen is shown This screen will be different on the various Interpreter sets depending on the individual set up of the Interpreter Unit If the welcoming screen does not disappear the interpreter set has not been set up For setting up the interpreter set please see next section A black dot in the middle of the first line indicates that the Audio out from the interpreter unit is muted The reason for this is communication problems Cables etc have to be checked Setup menu Before using an Interpreter Unit a set up of
17. inserting the connector Press OK to return to the Set up menu If the communication during start up is failing in a way that the Interpreter Unit will not work this screen will be shown instead of normal welcoming screen LCD backlight This menu gives the user the possibility to control the dimmed LCD backlight LCD backlight BON The user can toggle the backlight setting between ON and OFF by pressing the relay select buttons Press OK to return to the Set up menu Only dimmed LCD backlight can be controlled using this menu strong LCD backlight will be available if external Power Supply is connected AB switch with mic on AB switch with mic on means that the user can change the outgoing channel from A to B even when the microphone is active AB switch with mic on HON OK Cancel The feature is toggled between ON and OFF with relay select This feature is typically used in two language scenarios where an interpreter is responsible for translating from language A to B and also the reverse from language B to A Press OK to return to the Set up menu Normal operation As mentioned in previous chapter the following type of screen is shown short time after the system is powered up User Manual This screen will be different on the various Interpreter Units depending on the individual set up of the Interpreter Unit Please note if the welcoming screen is not disappearing
18. nce System Connection Details DCS LAN Chain The DCS 6000 system uses shielded Cat5e Cat6 or Cat7 F UTP or U FTP cables with shielded RJ45 connectors EIA 568 B wiring shall be used User Manual The phase of the pairs must be correct and the wiring spec as stated in Cat5e EIA 568 B have to be followed Important The names of Cat5 6 7 cable type have changed Note Cat6 and Cat7 cables can normally only be terminated in sockets female and not in cable plugs Cat6 and Cat7 can thus only be used for feeding cables terminating in wall outlets or patch panels FTP F UTP STP U FTP UTP U UTP Important Use only F UTP or U FTP shielded cables and shielded RJ45 connectors and not U UTP cable which are unshielded How to wire a Cat5e EIA 568 B cable to a RJ45 con Pin Function Connector 1 Connector 2 GRN wWuT s o muri murus BRN WHT 8 Outgoing BRN Important If other color codes are used then the four pairs are connected as follows Pair 2 Pin 1 amp 2 Pair 3 Pin3 amp 6 Pair 1 4 amp 5 Pair 4 Pin7 amp 8 Accessories Cat5e Connection Cables AWG24 6001 0 5 Connection Cable 0 5 m EC 600170 L iiu ott Connection Cable 1 m 6001 02 Connection Cable 2 m EC 6001 05 Connection Cable 5 m EC 6001 10 Connection Cable
19. one CU 61xx Central Unit and a number of Conference Units Gooseneck Microphones and other accessories depending on the system configuration The DCS 6000 system has the following main features e Fully digital e Excellent sound quality e State of the Art fully digital integrated interpretation discussion and voting system offering interpretation language distribution conference microphone and voting facilities with attendance check with Chip Card e Digital transmission of audio from to the Conference unit to from the central unit using a unique digital DATA and AUDIO bus named DCS LAN e Control of up to 3800 conference units This number does not include Channel Selectors Repeaters etc In practical use there are no limits for the number of Channel Selectors in a system e Delegate and Interpreter units are powered controlled by the CU 61xx Central Unit which drives up to app 50 units with the PS CU power supply e EX 6010 Extension Unit or PS 6001 DCS LAN Power Kit is available if more units are required e Delayed switching on of power to the two DCS LAN chains to minimize the total in rush current on the Mains supply e Designed for 31 interpretation channels and 8 open microphones e Audio scrambling of the audio to avoid eavesdropping e Designed in a standard 1HE 19 cabinet e TCP IP connection on CU 61xx for external operation of the system using a PC or control system such as AMX
20. peech 13 Call Not implemented Connectors 14 XLR connector XLR connector on the front is used for connecting a microphone to the unit Please note that only DIS series GM40xx and GM44xx can be used 15 Headphone connector On each side of the interpreter set a mini jack is located for connecting a headphone for listening to the Floor language or one of the pre selected relay User Manual languages a b c d On the left side a standard jack connector is also located with the same functionality 16 Headset Connector On the left side a DIN connector is located for connecting a DIS headset instead of a microphone 17 Display power connector The unit supports a dimmed backlight on off user selectable in the LCD display with no external power supply connected However special circumstances can required full light in the display At the bottom a power connector is used for connecting a optional Power Adapter used for supplying power for full light in the display Please note that the interpreter set is functioning perfectly also without light in the display Please observe that only the Power adapter supplied with the interpreter set can be used Other Power adapters might damage the interpreter set 18 Loudspeaker Connector A D Sub 9 pole connector for connecting the LS6032 Loudspeaker unit is located at the bottom of the unit 156032 Loudspeaker has a separate Volume control The loudspeaker w
21. r pre selection to scroll through the available languages 6 Floor DCS 6000 Digital Conference System This button selects the floor language as the listening language Outgoing Section 7 Microphone This button switches on the microphone When switched ON the button and the light ring on the gooseneck microphone will light red 8 Mute This button is used to temporarily switching off the microphone when coughing etc The channel is still occupied when pressing the button but the microphone is disconnected as long as the button is depressed Mute is indicated by switching off the light in the light ring of the microphone 9 A Press this button to select the A language as the outgoing channel A Red LED is indicating that A language is selected The Yellow engaged LED is indicating that the A channel is occupied i e a microphone on an interpreter set is switched on at this channel 10 B Press this button to select the B language as the outgoing channel A Red LED is indicating that B language is selected The Yellow engaged LED is indicating that the B channel is occupied i e a microphone on an interpreter set is switched on at this channel 11 B Select After pressing the B button the B language can be selected if ALL is chosen at the B mode selection in the B language set up menu 12 Speaking too fast Pressing this button sends a signal to the Chairman that the Speaker has to slow down his s
22. s selected then FLOOR will be shown preventing that the interpreter hears himself For testing purpose the corresponding a b c or d button can be pressed for 3 seconds the listening audio will then switch to the interpreter himself and the quality indication change to SELF When releasing the button the listening audio will switch back to Floor and the quality indication changes to FLOOR again If the A language is not selected the quality indication SELF is shown All a d selections show the actual quality of the channels at all times Selection of Outgoing channel The two push buttons A and B are used to select whether the interpreter will be routed to the A or B outgoing channel When A is pressed the red LED is lighted in the button When B is pressed the light in the A button will go out and the red LED in the B button will light up The A lines will always show the language of the one selected for the Interpreter Unit The upper line at the left shows the channel number and the lower line shows the languages in full name in accordance to the language list supported max 10 char When the system is initialised and set up then the A display will show the booth languages and A is automatically selected B display will show the B language selected at the B language Set up When B is pressed the light LED in the button is lit It is now possible to change the selection of the B language channel with the B sele
23. terpreter or the interpreters set itself occupies the channel Error indication If errors occur in the communication with the CU it will be indicated by the interpreters set The set has two error thresholds The first threshold is reached when audio data from the CU contains too many errors for the sound to be reproduced correctly This is indicated by a black matrix in the normal operation display and by the communication display when the set is un initialised The second threshold is reached when the frame error rate reaches a higher predefined value When this happens the set will enter the communication status display regardless of the state the set was in before errors occurred 11 DCS 6000 Digital Conference System User Manual The error status is checked every 5 seconds and the set enters the operation mode it was in when errors has occurred since the last check before errors was detected 12 DCS 6000 Digital Conference System User Manual System Setup General guidelines Connect the IS 6132 using Cat 5 FTP or STP cables e Maximum cable length in one chain when Please observe the following guide lines using repeaters is 650 m e Maximum cable length in one chain is 200 m If the last unit in one chain is a CS 6032 Channel without repeater This includes Selector this unit has to be terminated with an interconnection cables between the units external termination as the CS 6032 does not The max usable cable lengt
24. the Booth number and B language has to be done on all interpreters sets When b is kept depressed and B is activated the set up menu is shown Booth desk B language B mode Ver and serial no Communication status Y When the unit is un configured has not yet received an address the first two menus will not be available This is indicated by the missing Booth desk no A B language B mode Ver and serial no Communication status Y If the B select buttons is pressed the last two menu items are shown Backlight AB with mic on A menu is selected by pressing the button to the left of the menu a d Then the display shows the next level of menus or selections Booth selection Pressing the d button selects the Booth set up menu Booth a7 7 Norwegian Desk number Cancel 1 User Manual Press c button for selecting the Booth number for the Interpreter Unit A black dot is indicating the selection Then use Relay select up down to scroll through the available languages The Desk number will automatically change to the next available desk for the selected language To save the selection press OK B button If the desk number is set to an already occupied desk number the set will take over the configuration from the set on that desk and the other set will be loose the configuration B language selection When B language is selected by pressing the c button th
Download Pdf Manuals
Related Search