HS0005ECK01H - Renesas Electronics
Contents
1. N C AUDAT ASEBRK Input N C BRKACK 2 output RESET 2 Output User reset AUDATA1 10 N C N C 11 TDO Output AUDATAO 12 UVCC AUD Output N C 13 N C AUDSYNC 2 14 UVCC Output N C 15 TCK Input AUDRST 2 16 N C N C 17 TMS Input AUDMD 18 N C N C 19 TDI Input N C Notes 1 Input to or output from the user system 2 The symbol means that the signal is active low 3 The emulator monitors the GND signal of the user system to detect whether or not the user system is connected 4 Signal names are not intended to correspond to those for the actual MCU Refer to recommended circuits and notes described in the Supplementary Information on Using the SHxxxx and connect only the required signals Other than UVCC_AUD the signals are the same as those for the 36 pin interface Supply the operating voltage of the AUD to UVCC_AUD The GND bus leads which are allocated on the center of the H UDI port connector must be connected to GND When an MCU incorporating the AUD with the SSTL18 specification e g the SH7785 is used the emulator is used with the same circuit as for the E200F For details refer to the E200F emulator additional document Supplementary Information on Using the SHxxxx H UDI port connector top view Figure 4 1 Pin Assignments of the H UDI Port Connector 38 Pins ENESAS The following shows the correspondence betwee2. Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Renesas semiconductor products Renesas assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein 2 No license is granted by implication or otherwise under any patents or other rights of any third party or Renesas Figures Some figures in this user s manual may show items different from your actual system Limited Anticipation of Danger Renesas cannot anticipate every possible circumstance that might involve a potential hazard The warnings in this user s manual and on the emulator product are therefore not all inclusive Therefore you must use the emulator product safely at your own risk Ill TENESAS SAFETY PAGE READ FIRST READ this user s manual before using this emulator product KEEP the user s manual handy for future reference Do not attempt to use the emulator product until you fully understand its mechanism DEFINITION OF SIGNAL WORDS A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situat
3. LOST CAUTION Place the host computer and user system so that no cable is bent or twisted A bent or twisted cable will impose stress on the user interface leading to connection or contact failure Make sure that the host computer and the user system are placed in a secure position so that they do not move during use nor impose stress on the user interface VI ENESAS Contents Section 1 Components of the E10A USB Optional 38 Pin User System Interact DI ee eine Section 2 Connecting the Emulator to the User System 99 99 Section 3 Installing the H UDI Port Connector on the User System Section 4 Pin Assignments of the H UDI Port Connector Section 5 Restriction on Component Mounting uesseerssersnnesnnernnnennnen nme nenn Section 6 Notes sessssccsesesscesenssscssensoscesestsscssenssseesusssscesesssssenssesseesesasas RENESAS ENESAS Section 1 Components of the EIOA USB Optional 38 Pin User System Interface Cable Table 1 1 lists the components of the E10A USB optional 38 pin user system interface cable After unpacking the product check to ensure you have all components in table 1 1 Table 1 1 Components of the E10A USB Optional 38 Pin User System Interface Cable Guan Component Appearance tity Remarks User system interface cable o 1 38 pin type Length 30 cm Mass 62 g E10A USB Optional 38 Pin 1 HS00
4. 05ECKO1HJ and User System Interface Cable HS0005ECKO01HE User s Manual RENESAS Section 2 Connecting the Emulator to the User System Follow the procedure below to connect the EIOA USB emulator hereinafter referred to as the emulator to the user system with the user system interface cable and when reconnecting them after disconnection to move the emulator or user system 1 Ensure that the host computer is turned off or the emulator is not connected to the host computer with the USB cable 2 Connect the user system interface cable to the connector on the user side of the emulator 3 Connect the USB cable to the connector on the host side of the emulator ENESAS Section 3 Installing the H UDI Port Connector on the User System Table 3 1 shows the recommended H UDI port connector for this user system interface cable Table 3 1 Recommended Connector Connector Type Number Manufacturer Specifications 38 pin connector 2 5767004 2 Tyco Electronics AMP K K 38 pin Mictor type Note When designing the placement of the 38 pin connector layout on the user board reduce cross talk noise etc by keeping other signal lines out of the region where the H UDI port connector is situated ENESAS Section 4 Pin Assignments of the H UDI Port Connector Input Input Signal 4 Output 1 Signal 4 Output N C N C N C TRST 2 Input MPMD GND N C N C N C UCON GND 3 AUDAT AUDCK Output N C
5. 6887 7898 Renesas Technology Hong Kong Ltd 7th Floor North Tower World Finance Centre Harbour City 1 Canton Road Tsimshatsui Kowloon Hong Kong Tel lt 852 gt 2265 6688 Fax lt 852 gt 2730 6071 Renesas Technology Taiwan Co Ltd 10th Floor No 99 Fushing North Road Taipei Taiwan Tel lt 886 gt 2 2715 2888 Fax lt 886 gt 2 2713 2999 Renesas Technology Singapore Pte Ltd 1 Harbour Front Avenue 406 10 Keppel Bay Tower Singapore 098632 Tel lt 65 gt 6213 0200 Fax lt 65 gt 6278 8001 Renesas Technology Korea Co Ltd Kukje Center Bldg 18th FI 191 2 ka Hangang ro Yongsan ku Seoul 140 702 Korea Tel lt 82 gt 2 796 3115 Fax lt 82 gt 2 796 2145 Renesas Technology Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 Jalan Persiaran Barat 46050 Petaling Jaya Selangor Darul Ehsan Malaysia Tel lt 603 gt 7955 9390 Fax lt 603 gt 7955 9510 Colophon 6 0 E10A USB Optional 38 Pin User System Interface Cable HS0005ECK01H User s Manual ENESAS Renesas Electronics Corporation 1753 Shimonumabe Nakahara ku Kawasaki shi Kanagawa 211 8668 Japan REJ10J1363 0100
6. TAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE USER SYSTEM INTERFACE CABLE THE USE OF ANY USER SYSTEM INTERFACE CABLE OR ITS DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS WARRANTY THIS USER SYSTEM INTERFACE CABLE IS SOLD AS IS AND YOU MUST ASSUME ALL RISK FOR THE USE AND RESULTS OBTAINED FROM THE USER SYSTEM INTERFACE CABLE ENESAS State Law Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or conseguential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which may vary from state to state The Warranty is Void in the Following Cases Renesas shall have no liability or legal responsibility for any problems caused by misuse abuse misapplication neglect improper handling installation repair or modifications of the emulator product without Renesas prior written consent or any problems caused by the user system All Rights Reserved This user s manual and emulator product are copyrighted and all rights are reserved by Renesas No part of this user s manual all or part may be reproduced or duplicated in any form in hard copy or machine readable form by any means available without Renesas prior written consent Other Important Things to Keep in Mind 1
7. To our customers Old Company Name in Catalogs and Other Documents On April 1 2010 NEC Electronics Corporation merged with Renesas Technology Corporation and Renesas Electronics Corporation took over all the business of both companies Therefore although the old company name remains in this document it is a valid Renesas Electronics document We appreciate your understanding Renesas Electronics website http www renesas com April 1 2010 Renesas Electronics Corporation Issued by Renesas Electronics Corporation http www renesas com Send any inquiries to http www renesas com inguiry TENESAS 10 11 12 Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is gra
8. but Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers of
9. d by those who have carefully read and thoroughly understood the information and restrictions contained in the user s manual Do not attempt to use the emulator product until you fully understand its mechanism It is highly recommended that first time users be instructed by users that are well versed in the operation of the emulator product ENESAS LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and or workmanship Renesas will repair or replace any user system interface cables determined to be defective in material and or workmanship User system interface cables are wearing parts which Renesas will not repair or replace if damaged and or worn through use The foregoing shall constitute the sole remedy for any breach of Renesas warranty This warranty extends only to you the original Purchaser It is not transferable to anyone who subsequently purchases the user system interface cable from you Renesas is not liable for any claim made by a third party or made by you for a third party DISCLAIMER RENESAS MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED ORAL OR WRITTEN EXCEPT AS PROVIDED HEREIN INCLUDING WITHOUT LIMITATION THEREOF WARRANTIES AS TO MARKETABILITY MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR USE OR AGAINST INFRINGEMENT OF ANY PATENT IN NO EVENT SHALL RENESAS BE LIABLE FOR ANY DIRECT INCIDEN
10. ecision on the applicability of the information and products Renesas Technology Corp assumes no responsibility for any damage liability or other loss resulting from the information contained herein Renesas Technology Corp semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake Please contact Renesas Technology Corp or an authorized Renesas Technology Corp product distributor when considering the use of a product contained herein for any specific purposes such as apparatus or systems for transportation vehicular medical aerospace nuclear or undersea repeater use The prior written approval of Renesas Technology Corp is necessary to reprint or reproduce in whole or in part these materials If these products or technologies are subject to the Japanese export control restrictions they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination Any diversion or reexport contrary to the export control laws and regulations of Japan and or the country of destination is prohibited Please contact Renesas Technology Corp for further details on these materials or the products contained therein IMPORTANT INFORMATION READ FIRST READ this user s manual before using this emulator product KEEP the user s manual handy for future reference Do not attemp
11. ectronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics C 7 D qa 0 lt D D ENESAS E10A USB Optional 38 Pin User System Interface Cable HS0005ECKO1H User s Manual Renesas Microcomputer Development Environment System HS0005ECKO0O1HE Renesas Electronics Rev 1 00 2006 06 www renesas com Keep safety first in your circuit designs Renesas Technology Corp puts the maximum effort into making semiconductor products better and more reliable but there is always the possibility that trouble may occur with them Trouble with semiconductors may lead to personal injury fire or property damage Remember to give due consideration to safety when making your circuit designs with appropriate measures such as i placement of substitutive auxiliary circuits ii use of nonflammable material or iii prevention against any malfunction or mishap Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp product best suited to the customer s application they do not convey any license under any intellectual property rights or any other rights bel
12. fice equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions unde
13. igure 5 1 Restriction on Component Mounting ENESAS Section 6 Notes 1 When connecting the user system interface cable to the user system be sure to note the position of pin to avoid erroneous connections 2 Do not apply force to the user system interface cable while it is connected to the user system ENESAS E10A USB Optional 38 Pin User System Interface Cable HS0005ECKO1H User s Manual Publication Date Rev 1 00 June 28 2006 Published by Sales Strategic Planning Div Renesas Technology Corp Edited by Customer Support Department Global Strategic Communication Div Renesas Solutions Corp 2006 Renesas Technology Corp All rights reserved Printed in Japan RenesasTechnology Corp Sales Strategic Planning Div Nippon Bldg 2 6 2 Ohte machi Chiyoda ku Tokyo 100 0004 Japan ENESAS RENESAS SALES OFFICES http www renesas com Refer to http www renesas com en network for the latest and detailed information Renesas Technology America Inc 450 Holger Way San Jose CA 95134 1368 U S A Tel lt 1 gt 408 382 7500 Fax lt 1 gt 408 382 7501 Renesas Technology Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5FH U K Tel lt 44 gt 1628 585 100 Fax lt 44 gt 1628 585 900 Renesas Technology Shanghai Co Ltd Unit 204 205 AZIACenter No 1233 Lujiazui Ring Rd Pudong District Shanghai China 200120 Tel lt 86 gt 21 5877 1818 Fax lt 86 gt 21
14. ion which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE emphasizes essential information lt ENESAS 4 WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Do not repair or remodel the emulator product by yourself for electric shock prevention and guality assurance 2 Always switch OFF the host computer and user system before connecting or disconnecting any CABLES or PARTS 3 Connect the connectors in the user system and in the user system interface cable by confirming the correct direction RENESAS Warnings on Emulator Usage Be sure to read and understand the warnings below before using this emulator Note that these are the main warnings not the complete list 4 WARNING Always switch OFF the host computer and user system before connecting or disconnecting any CABLES or PARTS Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be
15. n the 38 pin and 36 pin connectors For the reguired processing between the target MCU and the connector refer to Supplementary Information on Using the SHxxxx Signal Name 38 Pin Connector 36 Pin Connector Note su eee aoe gt A MPMD PA 22 DA eee UCON MMM 33 AUDCK DB gt erro 1 T ASEBRK BRKACK AM 27 RESET LE 31 TO k TDO LAM 25 UVCC_AUD 12 Specific to the 38 pin connector 13 UVCC rem 29 TCK 1 17 160 TMS 171 seese 19 1B ween nnn n ne TDI 19 23 20 wrsennnnnee TRST gt pai 21 22 ee 233 AUDATA3 DA is 9 D TENESAS Signal Name 38 Pin Connector 36 Pin Connector Note AUDATA2 2811 7 27 mmnannnnnen AUDATA1 gt ee 5 29 wee nnnennn AUDATAO sc M BEE 3 BA AUDSYNC BO 11 BB FE AUDRST 34 nnnnnnnnno 13 35 memmmununun AUDMD 386 lia 15 B70 nnennnnnen Reserved ct Ys 35 6 TENESAS Section 5 Restriction on Component Mounting An upper limit 5 mm applies to the heights of components mounted around the user system connector The connector for the user system interface cable is of the straight plug type E10A USB optional 38 pin user system interface cable 2 5767004 2 gt 5 mm Pa EZ Area to be kept free of other components Target system H UDI port connector top view F
16. nted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document
17. onging to Renesas Technology Corp or a third party Renesas Technology Corp assumes no responsibility for any damage or infringement of any third party s rights originating in the use of any product data diagrams charts programs algorithms or circuit application examples contained in these materials All information contained in these materials including product data diagrams charts programs and algorithms represents information on products at the time of publication of these materials and are subject to change by Renesas Technology Corp without notice due to product improvements or other reasons It is therefore recommended that customers contact Renesas Technology Corp or an authorized Renesas Technology Corp product distributor for the latest product information before purchasing a product listed herein The information described here may contain technical inaccuracies or typographical errors Renesas Technology Corp assumes no responsibility for any damage liability or other loss rising from these inaccuracies or errors Please also pay attention to information published by Renesas Technology Corp by various means including the Renesas Technology Corp Semiconductor home page http www renesas com When using any or all of the information contained in these materials including product data diagrams charts programs and algorithms please be sure to evaluate all information as a total system before making a final d
18. r certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas El
19. t to use the emulator product until you fully understand its mechanism Emulator Product Throughout this document the term emulator product shall be defined as the following products produced only by Renesas Technology Corp excluding all subsidiary products e Emulator e User system interface cable The user system or a host computer is not included in this definition Purpose of the User System Interface Cable This user system interface cable is for connecting the emulator unit and user system This user system interface cable must only be used for the above purpose Limited Applications This emulator product is not authorized for use in MEDICAL atomic energy aeronautical or space technology applications without consent of the appropriate officer of a Renesas sales company Such use includes but is not limited to use in life support systems Buyers of this emulator product must notify the relevant Renesas sales offices before planning to use the product in such applications Improvement Policy Renesas Technology Corp including its subsidiaries hereafter collectively referred to as Renesas pursues a policy of continuing improvement in design performance and safety of the emulator product Renesas reserves the right to change wholly or partially the specifications design user s manual and other documentation at any time without notice Target User of the Emulator Product This emulator product should only be use
Download Pdf Manuals
Related Search