HDMI Extender with hub User's manual
Contents
1. IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 168 100 Subnet mask 255 255 255 6 f Obtain DNS server address automatically Default gateway i Use the following DNS server addresses m Preferred DNS server Alternate DNS server Advanced 2 Connect PC net port with TX or RX net port directly Power the system to connect PC and TX or RX through 3 Input TX 192 168 168 55 or RX 192 168 168 56 IP address to IE address bar and enter into control page 1 Click system on the page left menu bar then can modify IP and MAC address in switch information page gt C birpy 192 168 168 56 Settings Switch Infomation IP address 192 168 168 56 Subnet Mask 255 255 255 0 MAC address 00 0b 78 00 60 02 2 Click Uart settings to modify RS232 baud rate VI RFQ Q1 TV screen is black and OSD display searching TX on top left corner A1 Check TX and lan switch power status and network cable connection Q2 TV screen is black and OSD display Check TX s input signal A2 Check if the TX has HDMI signal input Change HDMI cable to retest Q3 The Lan port yellow indicator led does not light A3 Check the network cable quality and connection Q4 Video is stuck and unstable A4 Check if the network cables are too tong between all level cascade Q5 Have already modified IP address and need to modify2. again but forget the modified IP address and unable to enter into webpage A5 Long press the IR reset button for 5s and can restore IP and MAC to default factory setting Q6 Product can not work normally after changing IP address A6 IP setting may fail Long press IR reset button for 5S to restore IP address to default factory setting and change to a new IP address Make sure the IP of these RXs and TXs connecting to the same network is in the same network segment ViI SPECIFICATION Specifications Power DC5V1A supply Support 480i 60Hz 480p 60Hz 576i 50Hz input 576p 50Hz 720p 50 60Hz resolution 1080i 50 60Hz 1080p 50 60Hz Support 480p 60Hz 576p 50Hz 720p 50 60Hz output 1080p 50 60Hz resolution Support 640x480 60Hz 800x600 60Hz HDMI 1024x768 60Hz 1280x720 60Hz graphics 1280x768 60Hz 1280x1024 60Hz resolution 1360x768 60Hz 1366x768 60Hz 1400x1050 60Hz 1440x900 60Hz 1680x1050 60Hz 1920x1080 60Hz 44 1kHz 48KHz Video M JPEG Compressing Format Transmission Standard TCP IP it s with good compatibility Protocol of network equipment and good for network transmission and extension Transmission Within 70ms for direct connection delay with TX and RX Network UPT STP cat5e 6 cable Network CAT5 lt 80m cable CAT5E lt 100m length CAT6 lt 120m between all connections Offer standard full duplex RS232 transmission path baud rate can be modified Support LAN bandwidth Network Up
3. data 3 4 5 3 RX1 send data to TX TX IP address ASCll code data RX1 RS232 port input CO A8 A8 37 41 42 43 TX RS232 port output 41 42 43 ASCII corresponding decimal data AB C VI Modify IP amp MAC address and RS232 baud rate Product factory setting Setting notes by default TX IP It will not influence product address 192 168 168 55 normal work when connecting to 6 or 7 products if not RXIP 192 168 168 56 changing IP address Please address note TX and RX have to be in the same network segment and have different IP and MAC address TX MAC It will not influence product address normal work and not suggest to change address Uart 115200bps Can be modified to 1200 2400 settings 4800 9600 19200 28800 38400 43000 57600 115200 System module has built in HTTP server Can modify IP MAC address and RS232 baud rate according to webpage Long press IR reset 5S can restore the above parameters to default factory setting Setting procedure as below 1 Set PC s IP network segment the same with TX RX s IP segment such as 192 168 168 100 Take win7 for example Control Panel All Control Panel Options Network and sharing center Local network connection Property Internet Protocol Version 4 Internet Protocol Version 4 TCP IPv4 Properties ajx General e You can get IF settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate
4. HDMI Extender with hub User s manual IMPORTANT SAFETY INSTRUCTIONS 1 Do not mix up transmitter TX and receiver RX before installation 2 Use DC5V power supply only Make sure specification matched if using adapters not supplied by factory 3 Do not access external network PACKAGE CONTENTS HDMI to Lan Lan to HDMI sender TX 1pcs receiver RX 1pcs User s DC5V1A 2pcs manual 1pcs ll INSTALLATION REQUIREMENTS 1 HDMI source device computer graphics card DVD PS3 HD monitoring equipment etc 2 SDTV HDTV projector with HDMI port 3 UTP STP cat5e 6 cable 4 The max network cable length supported between Lan switch and TX RX connection CAT5 80m CAT5E 100m CATG 120m lll Interfaces 1 TX rear panel DC5V Power input HDMI in HDMI input IP reset Long press 5S and resort IP address to factory setting LAN1 LAN4 Network signal output connect with 4 RXs simultaneously 2 RX rear panel LAN1 LAN2 LAN3 LAN4 O DC5V Power input HDMI Out HDMI output IP reset Long press 5S and resort IP address to factory setting LAN1 LAN4 Any of the LAN port has signal input the other LAN ports output the same network signal and cascade more RXs 3 Front panel re a A ze ee 9 RS 32 OD RS232 Power indicator LAN1 LAN4 Network connection indicator Slow blink Network connection Fast blink Data is transmitting Reset Press to reset IV INSTALLATION PROCEDU
5. RES 1 Cat5e 6 network 1 7 Follow the standard of IEEE 568B 1 Orange white 2 Orange 3 Green white 4 Blue 5 Blue white 6 Green 7 Brown white 8 Brown VD 2 Connections HDMI output Note 1 OTX connects with HDMI input signal and supports 4 ways LAN simultaneous output Connect with network switch to extend signal HDMI output of RX connects with HD display or other HDMI devices Note 1 connect with multiple RXs at the same time to achieve identical and synchronized display V RS232 features 1 This product offers standard RS232 Path only for practical project RS232 communication and cannot control product 2 RS232 is full duplex communication path baud rate is 115200bps by default and it can be modified as per requirements Please refer to VI Part for modify procedure 3 RS232 usage RS232 sends data in the way of destination IP address hexadecimal data ASCII code RX side will shield IP address and send data through RS232 Check below diagram about the usage RX RX m i i RS232 Device RS232 Device RS232 Device Padaress IP adaress hexadecimal 1 TX send data to RX2 RX2 IP address ASCII code data TX RS232 port input C0 A8 A8 3A 30 31 32 RX2 RS232 port output 30 31 32 ASCII corresponding decimal data 0 1 2 2 RX2 send data to RX1 RX1 IP address ASCII code data RX2 RS232 port input CO A8 A8 38 33 34 35 RX1 RS232 port output 33 34 35 ASCII corresponding decimal
6. to 80MHz at the highest resolution data transmission rate Power Tx 3 5W Rx 3W at the highest resolution consumption Working 10 C 45 C temperature Storage 20 C 80 C temperature Working 10 80 RH not solidified humidity Storage 5 90 RH not solidified humidity Product LxWxH 140x85x27 mm dimension Declaration The product name and brand name may be registered trademark of related manufacturers TM and may be omitted on the user manual The pictures on the user manual are just for reference and there may be some slight difference with the real products We reserve the rights to make changes without further notice to a product or system described herein to improve reliability unction or design
Download Pdf Manuals
Related Search