USER'S GUIDE - Hit
Contents
1. Set the key ball in the hole Confirm that the key ball is set Insert a setting bolt into the hole at the bottom of the key box and tighten up by hand Photo 4 As tightening the bolt the hole for the key ball goes down hand tighten it further with the hexagon wrench until the inside hole is placed at the center of the outside hole Photo 5 Photo 6 Insert the key ball with a ring deeply into the hole of the key box If it is blocked by the ring and does not come down tighten or loosen the setting bolt and or press down the edge of the ring around the key ball by the fingernail until the key ring fits in the hole properly in the hole of the key box by sliding the red slide cover down over the hole Photo 7 Insert the key ball with a ring deeply into the hole of the key box Pull the wire loop attached to the key ball downwards and lower the red slide cover over the hole If the slide cover is blocked by the ring and does not come down tighten or loosen the setting bolt and or press down the edge of the ring around the key ball by the fingernail until the key ball fits in the hole and the slide cover comes down 3 P T O 11 Install an unused gas cartridge of the right size Photo 11 see page 2 Screw an unused gas cartridge until it is firmly seated do not over tighten If there is a problem with fitment consult with an authorized dealer CAUTIO2. unlocked position after the wire is pulled strongly Richie PS ront Soe 17 about SOs me sate coiler wier CO Gas Cartridge The gas cartridge contains CO gas When the key ball is released from the key box a needle punctures the seal of the gas cartridge to let the gas go into each air cushion O Screw the CO cartridge fully into the bottom until it cannot go any further Otherwise a needle in the key box may not puncture the seal of the CO cartridge and Hit Air may not be activated properly Do not reuse the gas cartridge once used Change it to a new one The seal at the bottom of an used cartridge is pierced with a hole Observe the followings to avoid an explosion WARNING A 1 Keep and use at the temperature below 40 C 104 F Do not keep in the car where the temperature may go up high WARNING A 2 Do not give the cartridge a strong shock WARNING A 3 Do not heat the cartridge WARNING A 4 Do not let corrosion form on the surface of the cartridge If corrosion is noticed replace it immediately WARNING A 5 Confirm that the used gas cartridge is empty of gas before disposing WARNING A 6 Do not cut or puncture the gas cartridge WARNING Az The size capacity of the gas cartridge varies from model to model Install the designated size capacity for the model Visit http www hit air com Replacement Gas Cartridges list to find out the right size for th
3. CID Attention after Activation BG Re assembling Hit Air after Activation EG How to Re assemble ae a ee ee ee ee eee ee ee DA phonies m e a M Re assembling Key Box rete ee 22 CSD Washing Ea CEID How to Store BEJE EAO change mem Safety Precautions Protector tube See P 16 Made of such non slippery materials as rubber or silicon to avoid abrasion of the part where the wire is tied Wing screw attached to the saddle or to the saddle strap our own product Tighten with a wing screw Be sure to read this User s Guide carefully before using the jacket with the Hit Air shock buffering system for proper use and safety and keep it in the place you can reach anytime e g in the motorcycle The marks used in this User s Guide denote as follows This mark denotes that if the WARNING is ignored it could result in death or a serious injury to the user This mark denotes that if the l of this product I CA UT I O N CAUTION is ignored it could result in a physical injury or a material damage CAUTION A 9 To make sure the Hit Air will function properly take it to an authorized dealer for a maintenance check once a year depending on frequency of use WARNING A 1 The jacket with the Hit Air is to be used for the rider s safety when riding a horse and not for any other purpose WARNING Ap The jacket with the Hit Air of the right size is to be worn as an oute
4. see page 22 to 25 i The key ball must be set only after the used empty I eS cartridge is removed from the key box The red slide cover is lifted to the unlocked up position It will be activated when the key ball O Is there any deterioration of the wire loop or comes out the coiled wire A screw hole at the bottom of the key box is visible The setting bolt is removed O A coiled wire is set properly See Attaching Coiled wire to Saddie page 17 to 19 Be sure to tie a 1 knot tightly EVERYDAY USE Read carefully before use lt S hit air E SHOCK BUFFERING SYSTEM AIRBAG JACKET ALL IN ONE AIRBAG USER S GUIDE For Horseback Riding lt B type Key Box gt The size capacity of the cartridge varies from model to model Make sure that the size capacity shown on the seal attached to the CO cartridge and that shown at the back of the key box cover are the same Some model has no size label attached If sizes shown as above are not the same it may cause a malfunction If the right size for the model is not clear check it against the Hit Air catalogue or visit our website i http www hit air com Saary check Replacement gas cartridge list o Es SRO JAPAN bidet A description of the size label varies from model to model 2 If the CO cartridge and the key box are not sealed or if the seal attached is torn at
5. Coiled wire to the center of the grab strap Pull the coiled wire until the loop is tightly fastened to the center of the grab strap Grab Strap Pass the coiled wire through the loop Coiled Wire How to fix a Coiled wire 2 Belt type to the Grab Strap Coiled wire 2 Fix it properly for the safety and the peace of mind CAUTION A 1 If the coiled wire is not attached to the saddle strap properly it may come off when it is stretched then the Hit Air will not be activated CAUTION A 2 Replace the coiled wire when wear burns peeling or cracks are found Do not use the coiled wire other than the one supplied by an authorized dealer CAUTION A 3 Don t use a rusty cracked or deteriorated grab strap or its metal fittings to avoid any possible trouble in activating the system CAUTION A 4 Activation of the system may delay if a coiled wire is not fixed firmly to the proper place of the center of the grab strap and is moving around CAUTION A 5 Don t fix a coiled wire directly to the metal fitting for the grab strap which may be broken or may come off at the activation and the system may not 47 inflate Connecting Coiled Wire and Jacket with Hit Air On the horseback hold both sides of the female part of the one touch release into which insert the mele connector Photo 1 Before getting off the horse press the press button of the one touch release for disconnection P
6. forgets to disconnect the one touch release and goes away from the horse farther than the activation distance a force of approximately 30kg 35kg See P12 may activate and inflate the Hit Air Connect or disconnect the one touch release while you are on the horse Once a gas cartridge is used it cannot be used again Buy a new one from an authorized dealer 2 For a belt adjustment around your waist pass the belt A Belt loop through belt loops without fail ate eS If the belt is not kept in the belt loops when the system is activated it may come off and the function of the airbag shock buffering may be impaired Although numbers of belt loops vary with models as Back before H model fe ED 0 MLV C model Removable hip cushion Velcro Back after Neck cushion At the activation the airbag inflates unbuttons a collar flap and stands up instantly Back cushion Two back cushions inflate and grow big Hip waist Side Cushion cushion At the activation Hip waist cushion of the system the H packed inside airbag under the inflates and pops gusset is unbuttoned out instantly at and inflates the activation Hip cushion r At the activation sau the airbag inflates unbuttons a hip flap and hangs down instantly Design and shape of model may vary 4 Function 1 As soon as the activation distance is reached the Hit Air is activated and the CO2 ga
7. s S wo LASA o N TO H Z Bar of a saddle RN Stirrups leather How to fix a coiled wire to the Saddle strap Pull the coiled wire until its loop is tightly fastened to the Saddle strap 7 Turnthe nm emblem gt side up i W Turn the emblem of the saddle strap up Pass the other end of and pass the loop of the coiled wire the coiled wire through through the ring of the center of the its loop saddle strap Saddle strap Loops at both ends can be fixed to the bar of a saddle Coiled Wire Saddle strap is to be fixed to the bar of a saddle of the saddle 2 i Bar of a saddle 2 Aoii t w ALS Fix loops at both ends of the Put stirrups leather in place Saddle strap deeply and firmly to the bar ofa saddle Stirrups leather CAUTION A 1 If the coiled wire is not attached to the saddle strap properly it may come off when it is stretched then the Hit Air will not be activated CAUTION 2 Replace the coiled wire when wear burns peeling or cracks are found Do not use the coiled wire other than the one supplied by an authorized dealer CAUTION A 3 Don t use a frayed and deteriorated saddle strap Replace it immediately otherwise it may be worn out and the system may not be activated CAUTION AN4 The saddle strap connected to the bar of a saddle may come off at the activation and the a
8. than Closely 2cm 0 8inch Metal fitting for the the Hit Air carefully at your own risk It may not work as designed if sacle Noder there are external or internal damages For further details for re assembling see Chapter 7 Pages 21 to 25 Don t fix a coiled wire directly to metal fittings for the grab strap which may be broken ormay come off and the system may not activate Re assembling Key Box 1 Get tools for re assembling ready Photo 1 gt 7 Re assembling Hit Air after Activation 7 2 How to Re assemble an unused ne pew a hexagon wrench and a setting fF FF We recommend to take the Hit Air once activated to an authorized dealer for a bolt ready Seine Doll ONAC KAGAN maintenance check and re assembling CAUTION Hexagon wrench attachment It can be reused if it is re assembled in accordance with the following procedure but unless As the CO cartridge for the jacket a Unused CO gas cartridge option it is done properly it may not work with the Hit Air varies in size It cannot be re assembled if it is damaged by the previous activation capacity choose the right size of the cartridge matching the size of a How to Re assemble the wear y 4 The seal at the bottom ra h of an used cartridge is Find out whether it is reusable 2 Unscrew the used gas cartridge ft ee i byan maimtenance check of by turning anticlockwise an authorized dealer Photo 2 em Open Replac
9. N N If the cartridge is not seated completely and firmly the Hit Air may not be activated inflate Tighten f HDS Screw an unused cartridge as indicated on the seal attached to the cartridge 12 Take the female side of the one touch connector out through the hole of the key box cover and close the key box cover Photo 12 Take the connector out throug the hole of the key bo cover an ee ee eee ee ELES 25 End 8 Remove the setting bolt Photo 8 Loosen the setting bolt by the 5 mm hexagon wrench to remove it 9 Lift the red slide cover to the unlocked up position for reuse Photo 9 CAUTION A If the system activates while the red slide cover is in the locked down position it may cause the system malfunction or damage to the Hit Air 10 Re pack all air cushions and fasten all buttons Photo 10 Fasten buttons on the neck Fasten Velcro a on the neck i Fasten buttons on the back Fasten buttons on the sides Fasten buttons on the hip f Ren Velcro Re assembling Key Box WARNING A Remove the setting bolt from the key box without fail Otherwise the Hit Air will not be activated Re pack neck air cushions and fasten Pack the hip waist cushion inside and fasten with y Velcro P T O Washing 1 Hit Air jacket of all in one airbag should n
10. Specifications shapes and how to use may change without prior notice hit ib SHOCK BUFFERING SYSTEM MUGEN DENKO CO LTD 1 1012 Ikeba Tempaku ku Nagoya 468 0055 JAPAN phone 81 52 807 7750 fax 81 52 807 7901 E mail mugen nhit air com URL www hit air com horse Be sure to read this page before using and after re assembling the Hit Air Thank you for using the Hit Air For your safety peace of mind and correct use of your airbag jacket make sure that items are confirmed before use as follows Caution N O Unless the Hit Air is set correctly it may not work or may cause a malfunction O Once a CO cartridge is activated it cannot be used again Remove it from the key box without fail Use a Hit Air CO cartridge only Do not use any other one A CO cartridge of the right size capacity for the model is installed The seal attached the cartridge shows its size capacity iar 2 Sealed properly No damage to the seal No seal is attached in case re assembling is done by yourself Unused CO cartridge and the key box are properly sealed at 5 CO gas cartridge the time of shipment The key ball is set E e The right size capacity cartridge for the model is installed 4 e A CO cartridge is tightly screwed into the key box Ks e An used empty cartridge should not be installed Caution Re assembling after the activation must be donein __ r accordance with Re assembling Key Box i
11. e jacket CAUTION A 8 Use the gas cartridge for the Hit Air only and not for any other purpose CAUTION A 9 Use a Hit Air CO gas cartridge only Do not use any other one CAUTION A 10 Keep the gas cartridges out of the reach of children CAUTION A 1 Once the gas cartridge is installed don t attempt to turn loosen or remove it CAUTION A 12 Screw the CO cartridge fully until it seats firmly in the key box but do not over tighten gt 5 Using Hit Air One touch Release Connect the male connector at the end of the coiled wire attached to the saddle with the female connector attached to the key ball in the key box Female Male Hold the female connector and insert the male one A clicking sound confirms that a connection has been made Pull the male connector lightly to make sure that the connection has been made properly CAUTION N 2 If you have difficulty making the connection clean the male and female parts thoroughly CAUTION A N 3 Change it for a new one if the insertion cannot be made properly Insertion by force may cause a malfunction of the one touch release Coiled wire Coiled wire 2 Easy to adjust its length with the belt and easy to attach to the right place _ lt i M ig _ T Coiled wire Se ree a A Loop setter e Buy an additional coiled wire for each additional saddle Metal fitting for the Grab Strap Bar of a saddle Fix the
12. e parts such as gas I cartridge by an authorized E Unscrew the used dealer and reuse cartridge to remove W from he key box as indicated in the seal Re assemble by yourself by using attached to the the setting bolt and the hexagon cartridge wrench both of which are supplied as attachments to the Hit Air 3 Remove all CO2 gas from the air cushion To remove all remaining gas from the air cushion spread the 3 Hit Air face down on a flat Outline of re assembling by yourself smooth surface By pressing down each cushion using your Unscrew VF No Damage Replace the gas cartridge Get an unused CO cartridge and tools for re assembling ready See lt P22 Chapter 1 hands knees and legs remove v gas completely Unscrew the used cartridge See P22 Chapter 2 Do not fold or roll up the Hit Air to avoid damages inside It may take time to release all the gas in Remove all CO gas from the air cushion See P22 Chapter 3 the air cushion but it is necessary v as it cannot be re assembled with Set a key ball in the key box by using tools See P23 to 24 Chapter 4 to 9 gas left remamnmg many of the Vv air cushion Photo 3 Install an unused cartridge See lt P24 Chapter 10 CAUTION A 7v If the gas left remaining in any P he k of the air cushion it cannot be ut on the key box cover See P25 Chapter 11 to 12 reassembled C P T O 2 Re assembling Key Box 4 When it becomes too tight by
13. ey ball comes out of the key box ae 9 Then a needle in the key box is activated and punctures the seal of the gas cartridge a to inflate the Hit Air instantly K U D The key ball can be pulled out from any i i CO2 Gas cartridge a alban Key Box direction Photo 1 k24 R TA ed slide cover WARNING AM l i Do not take the key box apart or remove 5 any parts Key Ball z q en about O Red slide cover Lor Whenever using the Hit Air make sure the red slide cover is in the unlocked up position Photo 2 To re assemble the key box Athe red slide cover is to be used to confirm that the key ball is properly set in the hole of the key box Photo 3 If the key ball is not set in the hole properly the red slide cover will not come down WARNING AM 1 When the red slide cover is in the locked down position the key ball cannot be released from the key box then the Hit Air will not be activated This may cause an injury to the rider in case of an accident Whenever using the Hit Air make sure the red slide cover is in the unlocked up position Photo 2 CAUTI on AAN a Even if the red slide cover is in the locked position if the wire is pulled strongly the key box may activate the Hit Air to inflate The Hit Air may also inflate accidentally when the red slide cover is moved from the locked position to the
14. hoto 2 Oneftouchtrelease 4 female PORE OME NTA male Release Coiled Wire Is constructed with a strong wire made of Kevlar cord coated with urethane resin Tie a knot tightly Loop setter Protector tube Connector male Kevlar cord Urethane resin CAUTION A If cracks peelings burns or wear is found or the Kevlar cord s inner core becomes visible replace it immediately Otherwise it may break or come off the loop setter Each user must take responsibility for maintenance and replacement of the coiled wire Screw tightly Loop setter Butterfly screw The Loop Setter is used to secure the coiled wire after its length is adjusted CAUTION A When you get on the horse be sure that the butterfly screw has been screwed tightly CAUTIONA Place the coiled wire between the loop setter s groves and tighten the butterfly screw firmly Leave about 2cm 0 8 inch of the wire out of the loop setter after it has been tightened cut off any excess wire and put a cap on the end of the wire ieee yes chee Otherwise a wire may come off the loop setter and 2cm 0 8inch the airbag will not be activated Protector tube Made of such non slippery materials as rubber or silicon to avoid abrasion of the part where the wire is tied 2 How to fix a coiled wire to the saddle strap AN Fix the coiled wire to the center loop of the saddle strap i _ Saddle strap Coiled Wire Option o lt
15. irbag may not inflate How to fix a Coiled Wire Where to fix the saddle strap Coiled wire Attention after Activation 1 Turn the emblem of the saddle strap or Grab Strap up wind a protector tube around the upper side of the o CAUTION AN 1 A hissing sound of the gas coming out of the gas cartridge into the air center of the saddle strap ao and cithe nas iube Bar of a cushion or the end of thecoil wire tapping a horse may excite the horse Pay attention when the jacket with the Hit Air is inflated as follows 2 The jacket with the Hit Air is designed to provide protection especially 2 Pass a coiled wire through How to adjust the length of to the wearer s neck so when it is inflated there will be some pressure the protector tube a coiled wire around the neck and if there is difficulty in releasing the helmet s strap enna up open the front fastener or buckle immediately wi a stretched 3 Look around the scene carefully unzip and release the buckle to take off the jacket 4 If the scene of accident seems to be dangerous go to a safe area before taking off the jacket outside the protector tube in the loop setter and adjust its length 5 When the jacket with the Hit Air is inflated a feeling of tightness may be felt but the gas will leak out gradually Therefore remain calm even if the body with the inflated jacket is with a ressed down by somethin slack wire P n Pu
16. om the coiled wire at the one touch release connector before dismounting the horse Otherwise it may cause an accidental activation CAUTION As Inspect the Hit Air to determine if there is any damaged prior to wearing If there is any damage consult with an authorized dealer gt 2 General Information Coiled Wire To be placed inside the thigh Grab Strap Saddle holder or Saddle strap Our own product The jacket with the Hit Air Shock buffering Protection System is to be worn as outerwear when horseback riding It will be activated inflated immediately after a distance from the rider to the horse exceeds the activation distance 1 when the rider falls off or is thrown off the horse It will be activated at the moment the key ball is pulled out from the key box see E P12 This causes the gas cartridge to release the CO2 gas into the air cushions to inflate them immediately Inflated air cushions are designed to come between the rider s body and objects against which the rider may strike after falling off or being thrown off the horse The Hit Air will act as a buffer to absorb the shock of impact and reduce the risk of injury the rider who wears it However this does not imply or guarantee rider s safety The key ball requires considerable force to be pulled out and will not be released easily because of the elastic nature of the coiled wire thus the Hit Air
17. ot be washed laundered 2 It should not be dipped in the water 3 It should be dried in the shade if it gets wet How to remove stains Wipe with a wet towel Hang it up together with a CO cartridge spray water on its surface with a shower except on the key box which should not get wet How to Store For longer life and safety avoid the following conditions 1 High temperature Under the direct sunlight in the closed automobile near the heater or open flames etc 2 Exposure to rain or extreme moisture including steam and high humidity 3 Storing items on top of the Hit Air System Jacket 4 Leaving jacket within the reach of children pets or other animals 5 Folded or rolled up Hang up on a coat hanger is preferable Change If a problem listed below is found on the jacket with the Hit Air consult with an authorized dealer to change or repair replace 1 The jacket cloth or inner fabric cloth or inner fabric cloth mesh becomes frayed or is torn and inner tubing white polyurethane film is exposed 2 A crack or rust is found on the key box or on the gas cartridge 3 The coiled wire or the wire loop gets scraped and frays 4 Considerable change of color or deterioration of material
18. rwear on the upper half of the body CAUTION ANo Keep the Hit Air by hanging up on a coat hanger Do not fold or lay anything on it WARNING s Use the gas cartridge of the same size and contents as before when Avoid high temperature and high humidity replacing and confirm that there are no holes or tears in its seal CAUTI onA i 1 To avoid any damage to the airbag do not prick a needle or sew emblems or iron on the jacket with the Hit Air Consult with an authorize dealer where to sew an emblem WARNING As Do not take any parts of the Hit Air apart CAUTION As Remove sharp on pointed objects such as pins or pens from the jacket with the Hit Air or from the underwear before wearing They may damage the air cushion before or at the time of the activation and prevent the function of the Hit Air CAUTI onA 12 Make sure the coiled wire is securely attached to the saddle Improper attaching may prevent the function of the Hit Air CAUTION ANis Don t wash or launder the Hit Air all in one airbag CAUTION Ae Keep open flames and cigarettes away from the jacket with the Hit Air as holes or tears caused by them will prevent its function Keep and use at temperatures below 40 C 104 F as the gas cartridge may burst at a high temperature CAUTI on Zu If a fray rust on wear is found on the wire loop or the coiled wire attached to the key ball replace it immediately CAUTION AN Disconnect the Hit Air fr
19. s fully inflated but grabually decreases as gas comes out of the air cushion 3 The strength against breakage depends on the material of the jacket the material of the inner tube polyurethane and the strength of the stitch it also depends on the degree of impact shape or hardness of the object the rider may hit after the Hit Air inflates 4 The gas is sent from the key box to each air cushion through urethane tubing The Hit Air is designed to act as a shock absorber and may break depending on the shape of the object against which it strikes and also the extent of impact given 7 Key Ball PAR Key Ball E Key Ring 7 The key ball holds a compression spring and an interlocking needle in the key box When the system is activated the key ball comes out of the key box and a needle in the key box is released and punctures the seal of the gas cartridge to inflate the Hit Air immediately The key ball and the key ring are integrated parts Female Hit Air structure Hit Air all in one airbag of urethane film is attached directly to theinside of the cover inflates and absorbs the shock of impact Wier Loop One touch connector Key ball set MLV C model H model pe mm ame m SE L 3 Design and shape of model may vary A 3 Key Box O Key Box With a tensile strength of approximately Py 30kg 35kg by the coiled wire the a k
20. s is sent into the air cushions so that it will provide protection from the shock of impact even before it is fully inflated Structure 2 The CO2 gas cartridge and the key box area is covered by an ABS protector with buffer material to protect the rider s breast from the projecting objects in case of an accident 3 After the airbag is inflated in full the gas will leak out gradually Depending on the amount of the pressure given to the airbag by the accident a feeling of tightness may be felt but gradually subsides CAUTION A 4 The Hit Air may not function properly if there is a damage to the Hit Air cloth of the wear air cushion Velcro zipper buckle etc If so consult with an authorized dealer The Hit Air may not be repairable in some cases CAUTION A 5 Whenever the Hit Air is inflated even if there is no visible damage we recommend taking the Hit air to an authorized dealer for a maintenance check 1 Even if no damage is visible there may be damages to the air cushion Therefore take the Hit Air to an authorized dealer for a maintenance check to test the air cushion for leaks and inspect its parts to make sure it will function properly in case of an accident 4 W Air Cushion 1 The air cushions are made of high quality strong polyurethane film to absorb and reduce the shock of impact as much as possible when they are swollen 2 The maximum prcssurc is about 30kpa 0 3kg cni when the air cushion i
21. t wires in grooves 6 Ifthe air cushion is punctured when fully inflated the gas in all the F ANAO E U T cushions will immediately escape and the cushions deflate make the coiled wire fully stretched to determine the CAUTION N 7 If the Hit Air inflates accidentally for some reason while riding do not optimum length of the be alarmed Look for a safe place and take an appropriate action coiled wire Sitting or half CAUTION N 8 If there is external damage to the Hit Air due to its activation take it to crouching an authorized dealer for a maintenance check and to replace the gas TE i with a rtridge I f ext d ternally or internally it 5 Fix the coiled wire firmly in ed cartridge In cases of extreme damages externally or internally it may the loop setter tie a knot in its not be repairable end and cut off the excess leaving morethan 2cm 0 8 inch of extra length and put a cap on the cut end CAUTION N 9 Be aware of the points listed below when attempting to re assemble the Hit Air by yourself after it is activated Whether it has external damages holes scratches tears etc Confirm that the airbag is fully inflated when it is activated Confirm that the gas cartridge to be replaced is the correct size AN RAELE 2 Pass a wire 3 Knot tightly d d and unused through the gt V L loop 5 E ai 1 Form a loop Go over the points listed above and if there are no problems re assemble eave more
22. tees enaee Oa Air Cushion eesse reserse sser enrenenrenn A Key Box sss screenees Peel Key Ball ccc ccc eens ee Hit Air Structure c ccc cc ccc ees 13 CO Gas Cartridge c st dia hee E Sd 64 6 oe a das Connect with the saddle out to release the gas into the airbag instant 4 Key ring holds a key ball in the key box a One touch Connector gt Female r i 1 AS S Ring a Lin BQO ee oli AEA eam See P 15 When getting on a horse connect the male connector at the end of the coiled wire attached to the saddle with the female connector attached to the jacket One touch gt Connector Mal Female y Leave more than 2cm Using Hit Air BEE Pa Cap When getting on a horse One touch Release sre rrr r terre Ee connect one touch release Connecting Coiled Wire and Jacket with Hit Air BEIZ Loop SERET See P16 See P16 Attaching Coiled Wire to Saddle After a coiled wire is fixed to a motorcycle and its A strong wire of Kevlar f kevlar cord 1 How to fix a coiled wire to the Grab Strap Saddle holder length is adjusted place it in the grooves of the cord coated with mS 2 How to fix a coiled wire to the saddle strap Ern loop setter and tighten the wing screw urethane resin oe How to fix a Coiled Wire rere 19 Screw tightly Tie a coiled wire to the center of the saddle holder
23. the time of the purchase of a new product remove the cartridge and make sure that there is no hole at its bottom at the screw end e If there is no hole it is an unused cartridge to be installed in the key box for use Caution N If a CO cartridge is screwed into the key box loosely it may cause a malfunction See Re assembling Key Box in page 24 e If there is a hole at its bottom it is an used empty one and not usable Replace it with a new one _ ACO cartridge with a hole at its bottom is unusable An unused cartridge is to be installed in accordance with Re assembling Key Box see page 22 to 25 Make sure that the red slide cover is not in the locked down position andthe key ball is not set as yet The red slide cover is a tool to confirm that the key ball is set properly during the course of re assembling It should always be in the unlocked up position except during the course of re assembling see page 12 in detail Caution N The activation while the red slide cover is in the locked down position may cause damage or a malfunction to the Hit Air O Is there any deterioration of the wire loop or the coiled wire If there are signs of wear and tear replace it with a new one We recommend you to replace it in every one or two years O Make sure that the setting bolt has been removed from the key box The setting bolt is a tool to be used for setting the key ball into the hole of the ke
24. will not inflate under normally anticipated riding conditions including standing on pegs 1 The activation distance is defined as the length of the coiled wire stretched to its full length from the horse to the rider s key box on the Hit Air without any obstacles in between Name and Shape Hit Air jacket all in one airbag Name and shape Front before H model Key Box A CO2 cartridge is placed at the bottom of the airbag MLV C model s Lag ween oe oo a i al ES Inside waist l Inside waist gt adjust belt Velcro k adjust belt Velcro A Front after Side Cushion 9 Design and shape of model may vary l i l I S activation o distance lt lt va q N lt V nn U yy de A VX Ae key ball aie ai O If the coiled wire running from the key box to the saddle holder touches an obstaclesuch as the rider s body any part of the saddle a whip or any other projecting object there is a possibility of accidental activation within the activation distance by a force strong enough to pull the key ball out of the key box O If the rider crashes or falls down together with the horse unless the activation distance isexceeded the Hit Air will not be activated The Hit Air will not protect areas where the inflated air cushion does not cover O If the rider wearing the Hit Air
25. y box for re assembling see page 23 to 24 in detail The Hit Air will not be activated if the setting bolt remains in the key box Make sure that the setting bolt is removed from the key box before using the Hit Air X Setting bolt O Tie a knot tightly to fix a coiled wire to the saddle A knot works as the stopper to prevent the wire coming off when the Hit Air is activated Caution N Without a knot the wire may come off the Hit Air at its activation and the airbag will not inflate Be sure to read this User s Guide to use the Hit Air properly A maintenance check by an authorized dealer once a year is recommendable for your safety and peace of mind 2 gt Table of Contents hit air USER S GUIDE gt Preface Tools for Re assembling Accessories for Hit Air CO gas cartridge See P 14 When the key box is activated the gas cartridge OThank you for your purchase Hexagon releases CO gas into the airbag to each air C For the proper use of the Hit Air please read this booklet carefully before use wrench cushion immediately to inflate them 1 i a i 14 AS 5mm x C Please carry this booklet together with User s Guide for Accessories whenever you use the Hit Air i g Key box See P 12 to Dl Safety Precautions BEEE mer Setting i y bolt eee eee Key ball See P 13 General Information ae Key ball to be pulled a Name and Shape BE Structure EE Function ccc cect tect e teen
Download Pdf Manuals
Related Search