Home

OPERATING INSTRUCTIONS

1. With this operating mode for instance milk can be kept cool over night and warmed up automatically for breakfast 6 5 Operating mode Cooking Cooling e Cool down vanille pudding after cooking see point 3 5 during approx 5 minutes This avoids a drying out on the kettle basin bottom and on the walls during the portioning e Sauces and soups readily cooked to be decanted should be cooled down after being cooked to approx 30 Afterwards bring imme diately to the chill room e Cool down pasty food after being cooked to approx 35 for a further treatment Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 7 24 Safety instructions When emptying the stationary kettle by means of the ELRO drain valve there is danger of burning A careful handling is therefore important Before using the mixer remove the retention sieve Operate lid with the designated handle only If the maximum operating overpressure is exceeded by more than 30 kPa the pressure indicator starts to flash In this case the appliance must be switched off at once If the overpressure is rising any further you must reckon with escaping steam and hot water through the overpressure safety valve located in the area of the ELRO drain valve For your own safety we recommend to check the correct functioning of the overpressure safety valve every 4 years by our after sales service according to the regulations for
2. ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 16 3 6 Operating mode with mixer For the stationary kettle with integrated mixer JRW 2200 two different stirrers are available A stirring device with knives for solid components e p A milk stirrer with strippers for liquid and LA 7 pasty food When fitting the strippers 1 please pay attention to the inserting direction As shown in the illustration both strippers have to be directed to the f same side of the stirrer The smooth side of the strippers must point to the basin wall The milk stirrer will be used for creams and thick sauces By permanently strip E ping these liquids during the heating up and cooling down process a conside i rable acceleration in the change of the temperature can be reached When using the maximum speed during the cooling process please take into consideration that many types of food increase their thickness when cooling down i e a cream at approximately 100 may still be wa tery but at around 10 will have turned thick This will lead to a considerable increase of the necessary mechanical mixing capacity and in the extreme case of an increased speed to a thermal over stress In this case the process co
3. be the result of a lack of water Please check whether the pressure in the soft water system feeding heating system is adequate 3 10 Pressure indicator heating system recent The pressure in the heating system is displayed in the LED luminous band H1 If the pressure increa Ken ses by 19kPa 0 19 bar an additional luminous field f L Mo lo Ho 209280 lights up The operating overpressure of the heating system moves between 0 and 100kPa 1 bar If the maximum operating overpressure exceeds 30kPa the pressure indicator starts to flash the error message 14 appears and the heating switches off In this case please switch off appliance with key A1 and contact the ELRO after sales service 3 11 ELRO drain valve The ELRO drain valve 1 allows comp lete draining of the cooking chamber It prevents filling when the appliance has been improperly installed as well as th iN accidental opening through jolting or gt knocking When cooking solid food e g pasta j potatoes slide the retention sieve 2 2 1 into the discharge hole and hang it on Hh a the upper rim of the basin wall S Safety instructions KO Before using the mixer remove the reten L2 tion sieve Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 1 Valve piston A lift
4. biotite ee 22 6 3 Operating mode Cooling x flescceceiaeeseeedecececagecdsexeleceaucedecdsucudevusueuceocexaseceiuses 23 6 4 Operating mode Cooling Cooking ccccecessssecccceeeeeeeeeessseeeeeeeeeeeeeeeeeeees 23 6 5 Operating Mode Cooking Cooling ssssssssssrerereessssrerrnrrrnsseerrnnnnnnneseerrnne 23 7 Safety INSIRUCTIONS irienn eed daca inde eeereeaceds 24 Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 Ga 1 ELRO Stationary Kettle with integrated mixer Model JRW 2200 Congratulations on your buy of the new ELRO Stationary Kettle with integrated mixer model JRW 2200 This electronically controlled high performance appliance with integrated mixer the cooking function Optitherm and as an option a recooling device as well as a stirring device for solid components and a milk stirrer is designed for boiling liquids or pasty food This appliance is designed to be used in commercial kitchens restaurants hospitals canteens bakeries butcher s and commercial enterprises for the preparation and treatment of food Every other use of this appliance does not correspond to its purpose and can present a hazard to persons and or objects This appliance may not be used for the treatment of products which could cause caustic or corrosive vapours or could catch fire below a temperature of 120 The use of this appliance in vehicles or on board ships or aircrafts requires the auth
5. desired set point e Set cooking time in the display F1 with the adjacent keys F2 and F3 to the desired time An unlimited cooking time may be selected by pressing the key F2 until the sign appears in the display F1 If the mixer is used to support a cooking process this can be done with the following keys O e Start and stop the mixer as well as the direction gD of rotation with key E1 The selected rotating Hemo direction will be indicated by the corresponding LED DE O e Select between half and full speed with key D1 00 The selected rotating speed will be indicated by DO the corresponding LED eres e Select the interval programme lef hand motion intermission right hand motion with key C1 If this programme is not used the mixer turns continuously e Start cooking process with key A3 The LEDs in the selected keys are illuminated o Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 D amp o af 2s When starting the cooking process the two displays G1 and F1 switch from the set points to the actual values i e the cooking time remain ing time and the temperature of the food will be displayed The cooking time starts to run down only shortly before the temperature set point is reached countdown The LED of the cooking temperature G4 indi cates that the temperature set point has not yet been re
6. instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 O B2 O 15 In order to identify which partial process is programmed see the LEDs in key B2 By touching this key several times you may change between the two partial processes Note If a preceding cooking process has been stopped with key A3 it may last up to 7 minutes until the appliance has changed the mediums after the process start and the heating will switch on During this time the LED B2 is blinking 3 5 Operating mode Cooking Cooling O 2 O e Select the two step process cooking before cooling with key C2 This operating mode allows the combination of a cooking process with a cooling process The parameters for both partial processes may be adjusted before the process start and therefore no adjustments have to be made during the run down of the programme The entries for the cooking and cooling process have to be carried out one after the other in the displays F and G as described under 3 1 and 3 3 In order to identify which partial process is programmed see the LEDs in key C2 By touching this key several times you may change between the two partial processes Note If a preceding cooling process has been stopped with key A3 it may last up to 7 minutes until the appliance has changed the mediums after the process start and the heating will switch on During this time the LED C2 is blinking Operating instructions
7. relatively very watery and well conducting food broths thick sauces etc Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 8 This operating mode can be further used to reduce sauces e g thick veal and poultry sauces etc The use of the mixing device with the corresponding operating parameters in order to increase the warming up time of the food is at the chef s choice 2 2 2 Operating mode Optitherm D2 O The operating mode Optitherm key D2 has been developed to a achieve good cooking results with thick flowing pasty and difficult to TESA be warmed food With the normal cooking programmes thick flowing food is prone to dry out along the heated basin wall and finally to darken and to burn The operating mode Optitherm adjusts the heating capacity auto matically to the quality of the food By recognizing the quality a sticking or burning of the food on the basin inner wall is avoided and nevertheless it will heat up in an optimal time to the temperature set point The use of the mixing device with the corresponding operating parameters in order to increase the warming up time of the food is at the chef s choice The following operating modes are only possible with appliances with a cooling device 2 2 3 Operating mode Cooling optional Bb O The operating mode cooling B1 enables a very quick cooling down X of the food The mixer will start automatically and the dif
8. to the desired set point e Set cooking time in the display F1 with the adjacent keys F2 and F3 to the desired time An unlimited cooking time may be selected by pressing the key F2 until the sign appears in the display F1 If the mixer is used to support a cooking process this can be done with the following keys e Start and stop the mixer as well as the direction oD of rotation with key E1 The selected rotating Hemo direction will be indicated by the corresponding LED 1 O e Select between half and full speed with key D1 010 The selected rotating speed will be indicated by DO the corresponding LED 50 e Select the interval programme left hand motion intermission right hand motion with key C1 If this programme is not used the mixer turns continuously Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 10 e Start cooking process with key A3 The LEDs in the selected keys are illuminated When starting the cooking process the two displays G1 and F1 switch from the set points to the actual values i e the cooking time remai ning time and the temperature of the food will be displayed The cooking time starts to run down only shortly before the temperature set point is reached countdown The LED of the cooking temperature G4 indicates that the temperature set point has not yet been reached and therefore the heating is sw
9. 00063E 11 05 07 100 F 90 r 7 j 70 60 KARD 40o HHHH Food temperature 30 Ak 2 0 Wig 10 O 4 4 444 4444 I III 0 3 6 9 12 15 18 21 24 27 30 34 37 40 Cooling down resp heating up time min Cooling down curve with a capacity of 1261 and cooling water of 120 Cooling down curve with a capacity of 1261 and cooling water of 20 Sor Heating up curve with a capacity of 1261 and a steam pressure of 0 5 bar Heating up curve with a capacity of 126l and a steam pressure of 1 0 bar Considerable shorter cooling times may be achieved with a stationary kettle with integrated mixer than with the alternative of filling the food in GN bowls and cooling it in rapid freezers Furthermore food which has already been cooled in the cooking basin can be transferred immediately to larger compact containers regardless of the cooling qualities of the containers 2 2 Operating modes Besides the previously mentioned characteristics which are valid for both cooking programmes the following specific operative range for each operating mode will be explained hereafter 2 2 1 Operating mode Normal Cooking O The control pattern of the operating mode Normal Cooking key E3 has been developed in such a way that the quickest possible heating up to the boiling point is its main target This operating mo de will be used for
10. 5 hours in steps of 10 minutes After pressing the process start key A3 its LED begins to blink At the end of the retarded star ting time the LED in the key E2 goes out and the LED in key A3 will be on permanently The cooking process starts to run down When repeating a process after having switched off the appliance with key A1 the retarded star ting time has to be reactivated with key E2 The last set retarded starting time will then be available If the user would like to protect a running process against unintentional changes he can block the electronic control by means of an electronic key Block deblock Programme and start cooking process as described in chapter 3 1 to 3 5 e Within 3 seconds press first key E3 three times then key D2 twice This blocking can be cancelled by repeating the above pressing of keys E3 and D2 Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 18 3 9 Preparation phase For a change from one service mode into another very often a change of medium in the heating system water becomes necessary For this change the appliance needs up to 7 minutes During this time the LED in the key of the newly selected service mode is flashing As soon as the change of medium is finished the LED will be illuminated continuously and the new service mode will start Should the preparation phase last longer than 10 minutes this could
11. E L RAO Professional kitchens poean Anleitung vor Qriginalanleitung Gebrauch lesen N tice originale Lire la notice d utilisation 0 avant l emploi Original instructions Read instructions before use OPERATING INSTRUCTIONS ELRO Stationary Kettle with integrated mixer Model JRW 2200 a HE EHH See E Ee esd be kA Subject to alteration Contents Page 1 ELRO Stationary Kettle with integrated mixer Model JRW DOO E EA TTT AT 3 2 Electronic process control 8090 s ssceeeeeeeeeeeeeeeeeeeeeeeneeees 4 2 1 Basic information on the electronic process control 8090 eeeeeeeees 4 2 2 Operating modes 4 ciate el tet ell tte ke 7 2 2 1 Operating mode Normal Cooking ccccceceesseeeecceeeeeeeeeeeeeseeaeeeeeeeeeeeeeeees 7 2 2 2 Operating mode Opies so cccecre veces as eectenerwarvasduncc ver eeesevestensecer ereseeaserer deme 8 2 2 3 Operating mode Cooling Optional cceeeeceeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 8 2 2 4 Operating mode Cooling Cooking Optional ccceceeeeeseeeeeeteeeeeeeeeeeeeees 8 2 2 5 Operating mode Cooking Cooling Optional cceceeeeeeeeeeeeeeeeeeeeeeeeeees 9 3 Operating instructions s ssssnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nna 9 3 1 Operating mode Nor
12. ached and therefore the heating is switched on The LED F4 indicates that the cooking time is running down e By touching the keys G2 or G3 the temperature set point will be displayed If one of those keys is pressed longer than 3 seconds the temperature set point will be increased or reduced accor dingly e By touching the keys F2 or F3 the cooking time set point will be displayed If one of those keys is pressed longer than 3 seconds the cooking time will be extended or reduced accordingly e At the end of the set cooking time the signal horn will sound and the LED A2 will be on The end signal may be acknowledged by touching the key A3 e At the end of the cooking process switch off the appliance with key A1 When starting it again the last used set points of the cooking time and temperature will be available Note If a preceding cooling process has been stopped with key A3 it may last up to 7 minutes until the appliance has changed the mediums after the process start and the heating will switch on During this time the LED D2 is blinking Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 O i l o g 3 3 Operating mode Cooling Al m ef a Switch on apparatus with A1 Select cooling process with key B1 In both displays G1 and F1 the set points which have been used last in the operating mode cooling can be read Select e
13. ator heating system 2 1 Basic information on the electronic process control 8090 In order to give you the possibility to operate this stationary kettle with integrated mixer model JRW 2200 in the most advantageous way we shall give you hereafter some basic information about the temperature and cooking capacity control as well as the best possible cooling of the food The process control 8090 has a modern microprocessor system which can be pro grammed freely and therefore adapted in an optimal way to the control function Two cooking programmes keys E3 and D3 are available Besides an accurate tem perature and cooking time preselection they allow you to choose for the different cooking procedures optimal heating up and continuous cooking characteristics Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 5 As the two cooking programmes show a similar control pattern we shall first describe them to you According to the temperature set point the control 8090 regulates the cooking appliance either with the temperature or the cooking capacity control Temperature control The temperature control is active if you select a temperature between 30 and the boiling point in the display G1 adjustment see chapter 3 The appliance is then heating up according to the cooking programme with a maximum capactiy adapted to the food to be cooked just before reaching the set cooking temperatu
14. ays for temperature and time G1 and F1 switch from the set points to the actual values i e the cooling time is running down display of the remaining time The LED F4 is illuminated By touching the keys G2 or G3 the temperature set point will be displayed If one of those keys is pressed longer than 3 seconds the tem perature set point will be increased or reduced accordingly By touching the keys F2 or F3 the cooling time set point will be displayed If one of those keys is pressed longer than 3 seconds the cooling time will be extended or reduced accordingly At the end of the set cooking time the signal horn will sound and the LED A2 will be on The end signal may be acknowledged by touching the key A3 At the end of the cooking process switch off the appliance with key A1 When starting it again the last used set points of the cooking time and temperature in this operating mode will be available 3 4 Operating mode Cooling Cooking O BR O e Select the two step process cooling before cooking with key B2 This operating mode allows the combination of a cooling process with a cooking process The parameters for both partial processes may be adjusted before the process start and therefore no adjustments have to be made during the run down of the programme The entries for the cooling and cooking process have to be carried out one after the other in the displays F and G as described under 3 1 and 3 3 Operating
15. ccording to the cooking programme with a maximum capacity adapted to the food and as from there with approximately 1 3 of the highest possible capacity As you may gather from the diagram hereafter a weak bubbling will result from this regulation With this cooking capacity control it is possible to prevent an unwanted brisk or slight boiling and to avoid a loss of food quality e g bouillon may become clouded as well as unnecessary high energy costs brisk boiling 100 80 medium boiling 60 40 slight boiling l i 0 a 1 2 3 4 5 6 7 8 9 10 set heating capacity 10 cooking capacity With the adjustment of the cooking intensity steps from 1 to 10 the heating capacity will be increased each time by approximately 10 Cooling of food The stationary kettle with integrated mixer can be equipped with a food cooling device as an option and is then able to achieve optimal cooling times with a minimal water consumption As a cooling medium drinking water from the main or ice water which circulates in closed pipe systems can be used The flow of water in the double casing and the mixer axle has been optimized in such a way that a quick cooling in the temperature range of 45 to 15 as required by the food hygienists is possible As an example the following cooling curves can be achieved when boiling water Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X1
16. er Briskly boiling water e g to cook pasta step 5 10 Continuous boiling of pasta rice step 2 4 Blanching of vegetables bones etc step 10 Simmering processes like boiled beef ox tongue etc Boiling of ham sausages 72 750 Reduce Glace de viande step 8 10 The maximum adjustable temperature depends on the boiling point 6 2 Operating mode Optitherm The operating mode Optitherm key D2 has been developed to achieve good cooking results with thick flowing pasty and difficult to warm up food without sticking or burning When the basin is filled with a small quantity only the control system will limit the heating output automatically Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 S08 Temperature chart Food to be cooked Temperature set point Power step Heating up milk 85 900 Heating up milk for creams and puddings 95 98C Creams and puddings 92 950 Maize mash semolina mash rice pudding Melting butter Bearnaise and hollandaise sauce Thick flowing sauces e g bechamel sauce velout The maximum adjustable temperature depends on the boiling point 6 3 Operating mode Cooling With this operating mode the food can be cooled down in few minutes to an adequate portioning temperature approx 70 or to a tempe rature at which food can be put into larger containers in order to be brought to the chill room 6 4 Operating mode Cooling Cooking
17. ferent operating parameters of the mixing device may be selected In order to stop the cooling process a minimal food temperature or a cooling time has to be preselected 2 2 4 Operating mode Cooling Cooking optional O B2 O The operating mode cooling cooking B2 enables a fully automatic yy cooling followed by a cooking process The phase time and the phase temperature have to be preselected for the cooling phase as well as the cooking phase In the cooling phase the mixer will start to operate automatically with the standard parameters These may be altered as desired with the corresponding keys In the cooking phase the use of the mixer may be selected freely Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 9 2 2 5 Operating mode Cooking Cooling optional O amp 2 O The operating mode cooking cooling C2 enables a fully automatic uy cooking followed by a cooling process It is the time opposite process compared to the above mentioned operating mode Therefore all the above mentioned adjusting possibilities will apply 3 Operating instructions 3 1 Operating mode Normal Cooking en e Switch on appliance with key A1 E O e Select the cooking process Normal cooking with 7 key E3 In both displays G1 and F1 the set points which have been used last in the operating mode Normal Cooking can be read e Set temperature in the display G1 with the adjacent keys G2 and G3
18. igh pressure cleaner e When cleaning do not fill the appliance with water or detergent above the filling mark e Clean valve upper part and valve body of the ELRO drain valve with a commercial cleaning agent and dry thoroughly Then rub Vaseline or glycerine over both parts e f the valve fails to close tightly the seal 5 see drawing on page 19 can be re moved from the seal groove by means of a screw driver Place the new seal into the seal groove by hand and rub Vaseline or glycerine over it Use original ELRO seals only e After every 2000 working hours exchange the gear lubricant oil of the mixer motor For a refill use 1 5 of the CLP quality 198 242 mm s at 40 ISO VG 220 Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 DD 6 Cooking instructions 6 1 Operating mode Normal Cooking The control pattern of the operating mode Normal Cooking key E3 is designed for the quickest possible heating up to the boiling point Independent of the adjusted cooking capacity 1 10 the appliance heats up until close to the boiling point with full power 100 and as from there according to the adjusted cooking capacity When the basin is filled with a small quantity only the control system will limit the heating output automatically Temperature chart Food to be cooked Temperature set point Power step To bring water to the boiling point 96 100 Sight boiling wat
19. itched on The illuminated LED F4 indicates that the cook ing time is running down By touching the keys G2 or G3 the temperature set point will be displayed If one of those keys is pressed longer than 3 seconds the tempe rature set point will be increased or reduced accordingly By touching the keys F2 or F3 the cooking time set point will be displayed If one of those keys is pressed longer than 3 seconds the cooking time will be extended or reduced accordingly At the end of the set cooking time the signal horn will sound and the LED A2 will be on The end signal may be acknowledged by touching the key A3 At the end of the cooking process switch off the appliance with key A1 When starting the appliance again the last used values of the cooking time and temperature will be available Note If a preceding cooling process has been stopped with key A3 it may last up to 7 minutes until the appliance has changed the mediums after the process start and the heating will switch on During this time the LED E3 is blinking Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 te 3 2 Operating mode Optitherm e Switch on appliance with key A1 e Select the cooking process Optitherm with key D2 In both displays G1 and F1 the set points which have been used last in the operating mode Optitherm can be read e Set temperature in the display G1 with the adjacent keys G2 and G3 to the
20. ither the desired minimum temperature in the display G1 with the keys G2 and G3 or the desired cooling time in the display F1 with the keys F2 and F3 The minimum adjustable cooling temperature will be calculated automatically by the appliance depending on the temperature of the cooling medium i e the minimum adjustable food temperature may fluctuate slightly between summer and winter when using water from the main as a cooling medium An unlimited cooling time may be selected by pressing the key F2 until the sign appears in the display F1 When selecting the operating mode cooling the mixer will automatically be activated with the adjustments which have been used in the pre ceding cooling process These adjustments may be altered as follows Key E1 selects the rotating direction of the mixer By pressing this key several times you may change between left and right handed rotation Key D1 selects the speed of the rotation By pressing this key several times you may change between a medium and a maximum speed Key C1 selects the interval programme The mixer changes periodically between right handed rotation intermission left handed rotation If this programme is inactive the mixer works continuously Start cooling process with key A3 The LEDs of the selected keys are illuminated Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 a fA The displ
21. jJ gt 4 Handle L F J ed oa 3 Seals 2 Valve body e Remove the valve piston 1 of the ELRO drain valve only when the appliance lid is open e The ELRO drain valve becomes hot during operation Always use the foreseen handle when operating the drain valve e When draining the cooking chamber hot liquids or escaping steam can cause scalding burning Stand back when opening the ELRO drain valve e After each use clean the valve piston 1 and body 2 with commercial detergents Warning In the area of the ELRO drain valve hot water may escape After each use cleaning check e proper functioning e if parts are damaged and e piston seals 3 for tears or cuts If the valve is not functioning correctly or if parts are damaged contact ELRO After Sales Service Lubricate the valve piston 1 with Vaseline or glycerine before you insert it in the valve body at least once a week Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 20 4 System displays and settings 4 1 Error messages FAQ Fs Recognized errors will be displayed in the cooking h G min AN time display F1 All control outputs will switch off when an error is recognized F2 Error cooking basin probe 01 and 02 04 and 05 Error cooling water probe 06 and 07 Error pressure sensor 08 Thermo protection mixer motor 09 Heating interrupted by delimi
22. mal Cooking ceeeeeeeeeeecceeeeeeeeeeeeeeeaeeeeeeeeeeeeeeeeeaaaees 9 3 2 Operating mode Optitherm ccccccceeeeeeeeeeeeeeeceeeeeeeeeeeeeeneaeeeeeeeeeeeeeeeee 11 3 3 Op rating mode GooliNg iieis a aaa Eaa 13 3 4 Operating mode Cooling Cooking sssssssssssrsssesssrsrrnrrrnnsserrrnnnnnnneseernnne 14 3 5 Operating mode Cooking CoOoling ccceeeeeseececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 15 3 6 Operating mode with MIXEM ceeecceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaaeeeeeeeeeeeeeee 16 3 7 Retarded starting ti ceitcreteiciteteeh a cn ele nia eS cele E as 17 3 8 ISCULOMIG KEY EE AEE 17 3 9 Preparation NaS ec Gece cies ele oa ei lene ea aad ana eae 18 3 10 Pressure indicator heating system cccceeeeeeeeseeeeeeeeeeeeeeeeeaeeeeeeeeeeeeeeees 18 Sekt ELRO d r in valean aaea a Eea a aaea aeii 18 4 System displays and settings cccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeen 20 4 1 EET O E E E 20 4 2 Selection of temperature unit OF F ceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 20 4 3 Connection to a power limiting installation LBS optional 00 ee 21 5 Maintenance and Cleaning cccccceeseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 21 6 Cooking INSUFUCHION Ss 2eseciccesececceswececsucel sini dtenstiacenetcedsecnzeceveewten 22 6 1 Operating mode Normal COOKING ccccceceeeeeeeeeeeeeeeeeeeeeeeeeeeneneeeeeeeeeeeeeee 22 6 2 Operating Mode OnithenMt cscchis tinea
23. ntrol may stop the motor and notify the error message 8 After the motor has cooled down the appliance can be restarted by switching it off and on again with key A1 Safety instructions If you open the lid when the mixer is working the motor switches off and restarts only when the lid is closed again Caution When opening the lid the stirrer is still turning i e slowing down Do not touch the turning stirrer as your clothing may get caught which could lead to injuries Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 AAT 3 7 Retarded starting time O 3 8 Electronic key If the user would like a retarded starting time compared to the programming time e g a cooking process during the night this can be carried out with key E2 The retarded starting time can be used in the operating modes of the chapters 3 1 to 3 5 Programme the cooking process as described in chapter 3 1 to 3 5 Before starting the cooking process however with key A3 press key E2 The LED in key E2 will go on Select the desired retarded starting time in the display F1 with the keys F2 and F3 The user can select a retarded starting time in the display F1 up to 9 hours and 59 minutes with the keys F2 and F3 If a longer retarded starting time is adjusted the appliance switches to an hourly display i e the appliance can be programmed with a maximum retarded starting time of 99
24. orization of the manufacturer We are convinced that this appliance will satisfy all your demands Please read this manual carefully in order to take advantage of all the possibilities this kettle is offering you 2 o Saa COUN yy H F 3 i 1 Lid lifting handle 2 Electronic process control 8090 3 ELRO drain valve Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 sfiia 2 Electronic process control 8090 Key selection w9 s A1 On off for control U A2 Signal for process end horn ny A3 Start stop for process B1 Operating mode Cooling D Ba A B2 Operating mode Cooling Cooking j ene C1 Interval operation mixer te C2 Operating mode Cooking Cooling D1 Rotating speed mixer 0 p E Ta D2 Operating mode Optitherm EZ LV E1 Rotating direction mixer hera eS E2 Retardation of starting time o asia E3 Operating mode Normal Cooking Lan Gee F1 Cooking time display F2 Reduce cooking time ae F3 Extend cooking time F4 LED for cooking time G1 Temperature display G2 Reduce temperature G3 Increase temperature G4 LED for temperature heating is released H1 Pressure indic
25. pressure vessels The mixer is only working when lid is closed If you open the lid the mixer motor switches off Caution When opening the lid the stirrer is still turning i e slowing down Do not touch the turning stirrer as your clothing may get caught which could lead to injuries An improper use of the appliance filling up food over the food mark or an operation with 100 capacity in the continuous cooking range can lead to danger of burning by overflowing hot food When cleaning do not fill the appliance with water or detergent above the filling mark This is a thermal appliance Careless handling can lead to danger of burning Taking into account the machine noise information decree of 18th January 1991 this appliance is a technical working substance which does not cause noise or in special cases does not exceed a noise level of 70 dB A According to the directives for the connection of appliances to the drinking water supply the non return valve has to be checked on the occasion of each service In case of disturbances please contact the ELRO after sales service Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07
26. re and regulates it without upper deviation regardless of the quantity to be cooked This high regulating precision avoids a possible loss of quality e g sausages thick sauces If you choose the boiling point the heating capacity will be regulated in such a way that the temperature can be just kept i e with this regulation no bubbling is visible Depending on the food to be cooked and the filling content the control will release the full heating capacity for such a length of time that after the switching off of the heating the precise temperature set point will be reached by the remaining heat and an upper temperature deviation is avoided You may gather this control reaction from the following drawing JRW1 80 EID o I 1 2 full kettle aN oO 1 1 full kettle oO o Food temperature temperature set point 0 3 6 9 12 15 18 21 24 27 30 33 Heating up time min Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 Cooking capacity control If you like to set a certain cooking intensity after reaching the boiling point you must choose the cooking capacity control adjustment see chapter 3 Instead of the temperature you preselect a percentage capacity which will become active after the boiling point has been reached As an example we set the capacity to step 3 30 i e the appliance is heating up to the boiling point a
27. ter 10 Defect fuse control system 1 and 12 Processor error 14 Deviation of pressure in heating system 15 and 16 Error aeration sensor Blinking service mode key indicates a preparation phase see chapter 3 9 Please write down the error message and its accompanying circumstances and inform the ELRO after sales service If the boiling point adjustment of the appliance i e the maximum adjustable temperature does not correspond to the actually possible adjustment at the place of installation correct it according to the instructions in the installation and operating instructions chapter Adjustment of appliance to the altitude above sea level 4 2 Selection of temperature unit or F It is possible to select in the display G1 not only a cooking temperature in but also in F Fahrenheit The change between these two te mperature units is carried out as follows e Switch appliance off with key A1 e Touch key G3 and hold it then touch key A1 Let go both keys As from this moment the new temperature unit will be at your disposal If you like to return to the previous unit repeat the above mentioned procedure Operating instructions ELRO Stationary Kettle with Mixing Device JRW 2200 X100063E 11 05 07 21 4 3 Connection to a power limiting installation LBS optional This appliance can be prepared for the connection to a power limiting installation optional The aim of this installation is to reduce
28. the costs of the electrical energy consumption A time graduated release from the energy connections of appliances with a high connected load avoids a deviation from the mean maximally permitted connecting load during a measuring time e g 15 min of an object e g the kitchen The process controls will not be affected by this release and continue to work by means of a separate connection An intervention of the power limiting installation during a running process will be indicated by the flashing of the LED G1 In order to avoid a deterioration of the temperature and cooking capacity adjustment of the appliances please observe the recommendations in the installation pamphlets for the maximum turn off and minimum restore times of the heating 5 Maintenance and cleaning e These cooking appliances are made entirely from high grade stainless steel How ever they will need appropriate care Gentle cleaning agents soft cloths or soft brushes only may be used for cleaning Do not use cleaning agents which could scratch or corrode the surface e Cooking salt may be added to the cooking water in a diluted form only Otherwise the water has to be stirred until the cooking salt has dissolved Aggressive or caustic acting substances may not be added or boiled e When appliances are not in use for a longer period Leave lid open Wipe basin with little oil e The appliances should be washed down without pressure only do not use a water hose or a h

OPERATING INSTRUCTIONS

Contents

Download Pdf Manuals

Related Search

Related Contents