USER MANUAL
Contents
1. OBLAMATIK USER MANUAL TWINLEVEL INTERFACE Dual Wheel for shower and bath Disclaimer This manual was created with great care Oblamatik AG shall not be liable for technical or typographical errors and reserves the right to make changes to the product and or the instructions at any time without notice Oblamatik is not liable or responsible for direct or indirect damages which is in connection with the installation or operation of this product Imprint This manual is a publication of Oblamatik AG Gaeuggelistrasse 7 CH 7000 Chur SWITZERLAND All rights including translation are reserved Reproduction by any method for example photocopies or electronic recording are not allowed Reproduction in full or partly is prohibited These instructions represent the technical status at time of printing Y The user manual must be given to the user Please read this user manual carefully before using the system and keep in a safe place for future reference To reduce the risk of injuries scalding and electrical shock the safety precautions below must be instal led and followed Risk of injury This device is not intended for use by persons with different or reduced physical sensory or mental abi lities or who lack experience or knowledge unless they are under the supervision of or receive training for the use of the device by a person responsible for their safety CONTINUOUSLY TURNING THE CONTROL WHEEL2. IN THE CLOCKWISE DIRECTION MAY OVERRIDE THE PRE SET MAXIMUM TEMPERATURE RESULTING IN A RISK OF SCALDING If the power cord gets damaged it must be replaced by the manufacturer its authorized service agent or qualified personnel to avoid danger Never operate the device with a damaged cable or plug Do not pull on the power cable as this could cause damage to the cable and cause electric shock Malfunctions Possible cause Solution The device is not working Start Diagnostic Check that The control unit is connected to the mains There is no power supply failure The electric plug inside the control unit is well connected No water flow when activated Check that Your faucet is connected to the water supply Both angle valves are fully opened Check another faucet in the house if water is running The water supply hoses are not bent or twisted The supply hoses might be soiled The control unit is connected to the mains Minimal water flow Check that Both angle valves are fully opened The water supply hoses are not bent or twisted The supply hoses might be soiled Continuous water flow Press the ON OFF button Close angle valve or main valve After a few minutes open again It s still a continuous water flow close valve and contact your installer Use soft cloth soapy solution and water for regular care Wipe with a dry cloth Avoid the use of abrasives or solvents which damage the surface Damage caused
3. by inappropriate treatment by the user is not covered by our guarantee for shower application with temperature sensor Explanation of the knobs Functions knob 1 ON OFF Changing water temperature Functions knob 2 Changing water flow Switching hand head shower Basic functions Water ON Changing water flow Press 1x knob 1 Water ON Turn knob2 when water ON Change water flow Changing water temperature Water OFF Turn knob 1 when water ON Change temperature according LED color ring Press 1x knob 1 Water OFF blue cold red hot Saving Quick Access factory setting Quick Access 1 Quick Access 2 Quick Access 3 Press 1 x knob 1 Water ON by Press 2x knob 1 briefly Press 3x knob 1 briefly 36 Celsius and 8096 water Water ON by 37 Celsius Water ON by 38 Celsius flow and 8096 water flow and 8096 water flow Saving Quick Access Quick Access 1 Quick Access 2 Quick Access 3 Press 1x knob1 water ON Press 2x knob 1 briefly Press 3x knob 1 briefly like Quick Access 1 water ON like Quick Access 2 water ON like Quick Access 3 Changing water temperature turn knob 1 Changing water flow turn knob2 Press amp hold knob 1 until LED color ring is flashing PURPLE Release knob immediately Flashing 2x PURPLE Water OFF setting is saved Diverting head shower hand shower Press 1 x knob 1 Water ON Press 1 x knob 2 Diverting between hand shower head shower Sca
4. ilter ok Are cold and warm water supply lines correctly connected Diagnostic completed Flashing 2x ORANGE Diagnostic successfully completed Flashing 3x ORANGE Malfunction of the temperature sensors Contact Support Center Flashing 4x ORANGE Malfunction of the flow rate sensors Contact Support Center Troubleshooting if LED color ring is NOT illuminating Please check the cable connection between TLC Controller and Interface If you were unable to resolve the issue please contact Support Center Special functions Press amp hold knob 1 until LED color ring is flashing TURQUOISE Release knob immediately Flashing 1x TURQUOISE Special functions activated Flashing 2x TURQUOISE Special functions locked Changing between activation locking device press amp hold knob 1 until LED color ring is flashing TURQUOISE Release knob immedia tely Thermal desinfection extended menu activated A ATTENTION RISK OF SCALDING Run desinfection Press amp hold knob 1 until LED color ring is flashing TURQUOISE Release knob immediately Flashing RED Flushing with hot water Stop desinfection Press 1x knob 1 or wait 5 minutes automatic stop Factory setting Special function must be activated Press amp hold knob 1 until LED color ring is flashing BLUE Release knob immediately Flashing 2x BLUE Factory setting restored Functions are depending on the TwinLevel controller
5. is deactivated temperature and water flow like factory setting Activating the cleaning mode Deactivate Interface Scalding protection Turning knob 1 Changing temperature From z 38 C temperature increase in smaller ANANG are west GV Press amp hold knob 1 until LED color ring is flashing GREEN Release knob immediately Pop up open close Reactivate Interface Press amp hold knob 1 until LED color ring is flashing LIGHT BLUE Release knob immediately Pop up open or close Press amp hold knob 1 until LED color ring GREEN goes out or wait 45 seconds automatic reactivation Diverting tub head hand shower Diagnose Press 1 x knob 1 Water ON Press knob2 briefly Diverting tub hand and head shower Press amp hold knob 1 until LED color ring is flashing ORANGE Release knob immediately Start Diagnostic 1 LED color ring is illuminating RED Check if hot water flows No warm water is flowing Check the hot water supply line s hot water supply line open s hot water system activated s mesh filter ok Are cold and warm water supply lines correctly connected 2 LED color ring is illuminating GREEN Check if NO water flows Water flows Device is broken contact Support Center 3 LED color ring is illuminating BLUE Check if cold water flows No cold water is flowing Check cold water supply line Is cold water stop valve opened s mesh f
6. lding protection Turning knob 1 Changing temperature From 38 C temperature increase in smaller increments more wheel turns Activating the cleaning mode Deactivate Interface Press amp hold knob 1 until LED color ring is flashing GREEN Release knob immediately Reactivate Interface Press amp hold knob 1 until LED color ring GREEN goes out or wait 45 seconds automatic reactivation Press amp hold knob 1 until LED color ring is flashing ORANGE Release knob immediately Start Diagnostic 1 LED color ring is illuminating RED Check if hot water flows No warm water is flowing Check the hot water supply line s hot water supply line open s hot water system activated s mesh filter ok Are cold and warm water supply lines correctly connected 2 LED color ring is illuminating GREEN Check if NO water flows Water flows Device is broken contact Support Center 3 LED color ring is illuminating BLUE Check if cold water flows No cold water is flowing Check cold water supply line s cold water stop valve opened s mesh filter ok Are cold and warm water supply lines correctly connected Diagnostic completed Flashing 2x ORANGE Diagnostic successfully completed Flashing 3x ORANGE Malfunction of the temperature sensors Contact Support Center Troubleshooting if LED color ring is NOT illuminating Please check the cable connection between TLC Contr
7. nob 1 when water ON Change temperature according LED color ring Press 1x knob 1 Water OFF blue cold red hot Quick Access for bath factory setting Quick Access 1 Quick Access 2 Quick Access 3 Press 1 x knob 1 Press 2x knob 1 briefly Press 3x knob 1 briefly Water ON by 36 Celsius an Water ON by 37 Celsius and Water ON by 38 Celsius and 100 water flow 100 water flow 100 water flow Saving Quick Access Quick Access 1 Quick Access 2 Quick Access 3 Press 1x knob1 water ON Press 2x knob 1 briefly Press 3x knob 1 briefly like Quick Access 1 water ON like Quick Access 2 water ON like Quick Access 3 Start tub filling measuerment 10 liters of water will be filled in automatically Turn knob 1 Change water temperature Turn knob2 Change water flow Fill in desired water quantity Press amp hold knob 1 until LED color ring is flashing PURPLE Release knob immediately Flashing 2x PURPLE Water OFF setting is saved average temperature water flow and filling quantity which was last set Reset Quick Access Special function must be activated Quick Access 1 Quick Access 2 Quick Access 3 Press 3x knob 1 briefly water ON like Quick Access 3 Press 2x knob 1 briefly water ON like Quick Access 2 Press 1 x knob 1 water ON like Quick Access 1 Press amp hold knob 1 until LED color ring is flashing DARK BLUE Release knob immediately Flashing 2x DARK BLUE Water OFF reset settings filling quantity
8. oller and Interface If you were unable to resolve the issue please contact Support Center Special functions Press amp hold knob 1 until LED color ring is flashing TURQUOISE Release knob immediately Flashing 1 x TURQUOISE Special functions activated Flashing 2x TURQUOISE Special functions locked Changing between activation locking device press amp hold knob 1 until LED color ring is flashing TURQUOISE Release knob immediately Thermal desinfection extended menu activated A ATTENTION RISK OF SCALDING Run desinfection Press amp hold knob 1 until LED color ring is flashing TURQUOISE Release knob immediately Flashing RED Flushing with hot water Stop desinfection Press 1 x knob 1 or wait 5 minutes automatic stop Factory setting Special function must be activated Press amp hold knob 1 until LED color ring is flas hing BLUE Release knob immediately Flashing 2x BLUE Factory setting restored Functions are depending on the TwinLevel controller used for bath application with temperature and water flow sensor Explanation of the knobs Functions knob 1 ON OFF Changing water temperature Functions knob 2 Changing water flow Switching tub lt gt hand head shower Basic functions Water ON Changing water flow Press 1x knob 1 Water ON Turn knob2 when water ON Change water flow Changing water temperature Water OFF Turn k
9. used Oblamatik AG G uggelistrasse 7 CH 7000 Chur 41 81 286 70 00 info oblamatik ch oblamatik ch 222703 03 15
Download Pdf Manuals
Related Search