User Guide
Contents
1. from the standby mode Off The camera s power is set to the standby mode from On Note This setting only causes the control signals to be sent to the camera It does not indicate that the actual camera s power status is displayed This is used to select the type of camera control to be exercised by the AV HS410 s positioners PanTilt Panning is controlled by operating the positioner to the left or right Conversely tilting is controlled by operating the positioner up or down Zoom Focus Lens focusing is controlled by operating the positioner to the left or right Conversely lens zooming is controlled by operating the positioner up or down This is used to select the speed at which the camera pans or tilts or at which the lens is focused or zoomed Fast The operations are performed at the fastest speed Middle The operations are performed at the intermediate speed Slow The operations are performed at the slowest speed This is used to select the type of control to be exercised over the focusing of the connected camera Manual The focus is controlled manually Auto The focus is controlled automatically Panasonic Corporation 2011 2012 This is used to select the type of control to be exercised over the iris of the connected camera Manual The iris is controlled manually Auto The iris is controlled automatically Live Switcher AV HS410 Plug in Software2. Stop Stop video recording stop playback F4 Rec Pause Pause video recording F5 Control2 Forward Fast forward F2 Rewind Fast rewind F3 Panasonic Corporation 2011 2012 12 Live Switcher AV HS410 Plug in Software 4 GVG Protocol This application makes it possible to have the crosspoint switching AUTO transitions and other operations controlled once a remote control panel VS R45 made by Venetex or editor that supports the GVG100 communication protocol has been connected with a serial interface RS 422 The GVG100 communication protocol is supported There are no parameters on the sub menus 4 1 Communication port Connect the remote control panel or editor to the Editor connector on the rear panel of the AV HS410 using an RS 422 straight cable 4 2 Verified models AG A850 VS R45 serial 4 3 Functions Select the sub menu concerned from the Plug in menu and press F2 Open Menu to display the menu of the Plug in concerned MENU GYG Protocol The AV HS410 is subject to the following types of control from the remote control panel or editor lt Details of control gt Bus switching The bus materials are selected from the following A B Key fill key source DSK fill DSK source PinP1 PinP2 AUX1 to AUX4 Button trigger The same operations are performed as when the following Pushbutton control buttons have been pressed on the control panel of the AV
3. Sub menu pem Function rotary encoder operated CamCTL3 MEM Preset This selects the memory in which the preset information of F2 the camera is registered None Nothing selected MEM1 Use the memory registered in the PLUGIN MEM1 button MEM2 Use the memory registered in the PLUGIN ME M2 button Network IP Address This is used to input the IP address of the camera F2 connected Before connecting the camera check its IP address and input it here Port This is used to input the port number of the camera F4 connected Before connecting the camera check its port number and input it here When the button for the memory previously selected in the MEM Preset item of the CamCTL3 submenu is pressed and its button is set to ON lighted the preset information of the commercial camera can be registered played back or deleted SHOT MEM EVENT MEM El 8 9 copy PASTE STILL 1 STILL 2 TRIM IN 5 5 DEL CLIP 2 TRIM OUT PLUGIN 2 3 1 gt REV 7 gt gt UNDO gt gt PLUGIN MEM2 TRIM OFF PLAY MEMORY WIPE PATTERN 10 KEY Press a number key 1 to 10 after The preset information is registered in the number of the corresponding pressing the STORE button number key Hold down the number key Press a number key 1 to 10 after The preset information of the number corresponding to t
4. HS410 Auto button DSK button WIPE button button PinP1 button Pinp2 button Key button O Panasonic Corporation 2011 2012 13 Live Switcher AV HS410 Plug in Software Forced button ON The following functions are forcibly set to the On status Pushbutton lamp On control DSK FTB Key PinP1 PinP2 Forced button OFF The following functions are forcibly set to the Off status DSK FTB Key PinP1 PinP2 Pattern switching The BKGD and KEY transition patterns are changed Transition time change The following transition times are changed BKGD Key DSK PinP1 PinP2 Panasonic Corporation 2011 2012 14 Live Switcher AV HS410 Plug in Software 5 AUXP_IP This application makes it possible to have the crosspoint switching AUTO transitions and other operations controlled once a remote control panel VS R45 made by Venetex has been connected with a network There are no parameters on the sub menus e if the AUXP_IP software version is V2 00 or later it will run on an AV HS410 model whose system software version is V2 00 00 or later Conversely if the AUX_IP software version is earlier than V2 00 it will on an AV HS410 model whose system software version is earlier than V2 00 00 5 1 Communication port Connect the VS R45 to the LAN connector on the rear panel of the AV HS410 using a LAN cable Up to four VS R45 units can be co
5. or later CAM_COM This application makes it possible to control the pan tilt zoom focus and other functions from the AV HS410 once a Panasonic professional camera AW series has been connected with a serial interface RS 422 e the software version is V2 01 or later it will run an AV HS410 model whose system software version is V2 00 00 or later If the system version of the AV HS410 is earlier than V2 00 00 upgrade it to V2 00 00 or later P2 Remote This application makes it possible to control the recording playback and other operations from the AV HS410 once a Panasonic P2 device has been connected with a serial interface RS 422 GVG Protocol This application makes it possible to have the crosspoint switching AUTO transitions and other operations controlled once a remote control panel VS R45 made by Venetex or editor that supports the GVG100 communication protocol has been connected with a serial interface RS 422 The GVG100 communication protocol is supported AUXP_IP This application makes it possible to have the crosspoint switching AUTO transitions and other operations controlled once a remote control panel VS R45 made by Venetex has been connected with a network e the AUXP_IP software version is V2 00 or later it will run on an AV HS410 model whose system software version is V2 00 00 or later Conversely if the AUX_IP software version is earlier than V2 00 it will run on an AV HS4
6. 1 3 Functions Select the sub menu concerned from the Plug in menu and press F2 Open Menu to display the menu of the Plug in concerned MENU AW CAM IP Cam Menu __ Menu Operation On Mode PTSpeed AF PanTikt Y Fast Y Manual CamCTL2 MEM Preset None IP Address 192 168 0 10 CamCTL3 Network Panasonic Corporation 2011 2012 6 Live Switcher Item rotary encoder operated Sub menu AV HS410 Plug in Software Function CamCTL1 Cam Menu F2 This item is used to set whether the camera menus are to be displayed on an external monitor On The camera menus are displayed on an external monitor Off The camera menus are not displayed on an external monitor Note This setting only causes the control signals to be sent to the camera It does not indicate that the actual statuses in which the camera menus are displayed on the external monitor MenuOperation F3 This rotary encoder is used when the cursor is to be moved using the camera menu When it is turned clockwise the cursor moves down conversely when it is turned counterclockwise it moves up It takes effect when On is selected for the Cam Menu item Notes This rotary encoder can be operated when the AW HESO is used It cannot be operated when the AW HE100 or other camera is used CamCTL2 PTSpeed F3 This item setting is used to control the camera s power On The camera s power is set to
7. 10 model whose system software version is earlier than V2 00 00 O Panasonic Corporation 2011 2012 3 Live Switcher AV HS410 Plug in Software lt How to register the Plug in Software gt Preparing for registration 1 2 3 Have at hand an memory card with a memory size of at least 8 MB e SDXC memory cards are not supported Initialize the memory card using the AV HS410 Insert the memory card initialized using the AV HS410 into the memory card slot of the personal computer Download the desired Plug in Software zip files and copy them onto the hard disk of the personal computer Unzip the downloaded zip files Copy the HS410 folder onto the memory card Do not change either the folder configuration or the filenames Registration procedure 1 2 Insert the memory onto which the Plug in Software was copied into the memory card slot of the AV HS410 Press the PLUGIN button The Plug in Software currently registered in the AV HS410 is now displayed Check the vacant index numbers Press the VMEM SD Card button to light its indicator and display the SD Card menu Use F1 to display the File1 sub menu Use F2 to select Load in the Mode item and press F2 When F2 is pressed a file selection screen is displayed Use F1 to select Plug in for the type of file to be loaded at the SELECT item Use F3 to select a vacant index number checked earlier Use F4 to lo
8. Panasonic User Guide AV HS410 Plug in Software W1211TY1042 FJ VQT4G34 1 Live Switcher AV HS410 Plug in Software Contents OVA EA A 3 lt How to obtain the Plug in Software gt oooocccccccccccccccccncnnnnnnnnnnnnnnnnnononononononnnnnnnnnnonnnnnncnnnnnns 3 lt How to register the Plug in Software gt siii contest 4 lt How to start up the Plug in Software gt 5 lt How to operate the Plug in Software gt 6 GAMA 22d 22 SN ot a BEATERS RRR EO BEERS WOMENS OER intr Cntr mere a 6 11 COMMUNICATION Method 6 1 2 ae tat o Rall Rak A 6 13 FUNCIONS 6 2 9 242 Communication Method T OEE EEDE 9 2 2 EMS 9 2 3 o eee 9 do PLENO A A A 12 331 COMMUNICATION POM EAE EEE 12 3 2 Verified A okie nieve eee ee i 12 3 3 A 12 A NBG eis catalase rec E E E 13 4 1 Communication 13 4 2 We nitled Model 5 ei EEEE ENEE EE EEEE EE E 13 43 Ula LE iTo g CE O O Sal Sil Mas
9. ad register the Plug in Software Note A warning message such as one shown below appears if Plug in Software has already been registered in the index number selected above for registration WARNING INDEX is in use Please use another INDEX ErrNo 01010 Please press F5 to close the message In a case like this repeat the registration procedure starting from step 7 Checking the registration 1 2 Turn off the power of the AV HS410 and then turn it back on again Press the PLUGIN button and check that the Plug in Software has been registered Notes O Registered Plug in Software can be deleted For the deletion procedure refer to section 4 5 Plug ins lt Operations and Settings gt Operating Instructions e Registered Plug in Software cannot be saved from the AV HS410 onto an memory card Panasonic Corporation 2011 2012 4 Live Switcher AV HS410 Plug in Software lt How to start up the Plug in Software gt 1 Press the PLUGIN button and display the Plug in menu 2 Use F1 to select the Plug in Software The Plug in name of the Plug in Software registered is displayed on the sub menu Open Menu Enable Version Delete Execute Off V1 00 00 Execute 3 Use to select On for the Enable item If On has been selected for the Enable item the selected Plug in Software has already started up If has been selected for the Enable item select On turn off the p
10. annot be operated when the AW HE100 or other camera is used This item setting is used to control the camera s power On The camera s power is set to from the standby mode Off The camera s power is set to the standby mode from On Note This setting only causes the control signals to be sent to the camera It does not indicate that the actual camera s power status is displayed This is used to select the type of camera control to be exercised by the AV HS410 s positioners PanTilt Panning is controlled by operating the positioner to the left or right Conversely tilting is controlled by operating the positioner up or down Zoom Focus Lens focusing is controlled by operating the positioner to the left or right Conversely lens zooming is controlled by operating the positioner up or down PTSpeed F3 AF F4 IRIS FS O Panasonic Corporation 2011 2012 This is used to select the speed at which the camera pans or tilts or at which the lens is focused or zoomed Fast The operations are performed at the fastest speed Middle The operations are performed at the intermediate speed Slow The operations are performed at the slowest speed This is used to select the type of control to be exercised over the focusing of the connected camera Manual The focus is controlled manually Auto The focus is controlled automatically This is used to select the type of control
11. el Natal NETOS ENESENN 13 RUANO A daa 15 5 1 COMMUNICATION DOT A O EAE EEE EAEE REE NEA ANENE E Sa E 15 5 227 FUNCION St a Deals e 15 Abbreviations e Both SD memory cards and SDHC memory cards are described as memory cards in this manual When individual descriptions are provided they are featured individually O Panasonic Corporation 2011 2012 2 Live Switcher AV HS410 Plug in Software lt Overview gt By registering or installing the AV HS410 Plug in Software in the AV HS410 the pan tilt Zoom focus and other functions of Panasonics commercial cameras AW series can be controlled from the AV HS410 Furthermore the AV HS410 can be controlled from a remote control panel VS R45 made by Venetex to perform crosspoint switching AUTO transitions and other operations lt How to obtain the Plug in Software gt The Plug in Software can be downloaded from Service and Support on the home page whose address is as follows http pro av panasonic net The five Plug in Software applications listed below can be obtained CAM_IP This application makes it possible to control the pan tilt zoom focus and other functions from the AV HS410 once a Panasonic professional camera AW series has been connected to a network e The CAM_IP software runs in an AV HS410 model whose system software version is V2 00 00 or later If the system version of the AV HS410 is earlier than V2 00 00 upgrade it to V2 00 00
12. he number key pressing the RECALL button is played back Press a number key 1 to 10 after The preset information of the number corresponding to the number key pressing the DEL button is deleted Hold down the number key Up to 10 sets of preset information can be registered The registered preset information is held in the camera The numbers of the number keys used as the preset numbers by the camera The same preset memory can be selected in the CAM_COM software When the same preset memory is selected for both programs it will function in the one selected last Note When the power of the AV HS410 is turned off the PTSpeed AF and IRIS settings are restored to their defaults After turning on the unit s power these items need to be set again Panasonic Corporation 2011 2012 8 Live Switcher AV HS410 Plug in Software 2 CAM_COM This application makes it possible to control the pan tilt zoom focus and other functions from the AV HS410 once a Panasonic professional camera AW series has been connected with a serial interface RS 422 e the software version is V2 01 or later it will run on an AV HS410 model whose system software version is V2 00 00 or later If the system version of the AV HS410 is earlier than V2 00 00 upgrade it to V2 00 00 or later 2 1 Communication method Connect the camera to be controlled to the Com connector on the rear panel of the AV HS410 usi
13. ld down the number key Up to 10 sets of preset information can be registered The registered preset information is held in the camera The numbers of the number keys are used as the preset numbers by the camera The same preset memory can be selected in the CAM_IP software When the same preset memory is selected for both programs it will function in the one selected last Note When the power of the AV HS410 is turned off the PTSpeed AF and IRIS settings are restored to their defaults After turning on the unit s power these items need to be set again Panasonic Corporation 2011 2012 11 Live Switcher AV HS410 Plug in Software 3 P2 Remote This application makes it possible to control the recording playback and other operations from the AV HS410 once a Panasonic P2 device has been connected with a serial interface RS 422 3 1 Communication port Connect the P2 unit to the Com connector on the rear panel of the AV HS410 using an RS 422 straight cable Select Config menu COM Port sub menu Mode item and set 2 for the item 3 2 Verified models AJ HPM200 e AG HPD24 3 3 Functions Select the sub menu concerned from the Plug in menu and press F2 Open Menu to display the menu of the Plug in concerned MENU P2 Remote Play Rec Sto Rec Pause Execute Execute Execute Execute Forward Rewind _ Execute Execute Control1 Start playback Start video recording F3
14. ng an RS 422 crossover cable Select Config menu COM Port sub menu Mode item and set 1 for the item 2 2 Verified models e AW HE50 2 3 Functions Select the sub menu concerned from the Plug in menu and press F2 Open Menu to display the menu of the Plug in concerned MENU AW CAM Serial Cam Menu Menu Operation je On On Mode PTSpeed AF IRIS CamCTL2 Pantilt Fast Y Manual Manual MEM Preset Panasonic Corporation 2011 2012 9 Live Switcher Sub menu Item rotary encoder operated AV HS410 Plug in Software Function CamCTL1 CamCTL2 Cam Menu F2 MenuOperation F3 Power F5 Mode F2 This item is used to set whether the camera menus are to be displayed on an external monitor On The camera menus are displayed on an external monitor Off The camera menus are not displayed on an external monitor Note This setting only causes the control signals to be sent to the camera It does not indicate that the actual statuses in which the camera menus are displayed on the external monitor This rotary encoder is used when the cursor is to be moved using the camera menu When it is turned clockwise the cursor moves down conversely when it is turned counterclockwise it moves up It takes effect when is selected for the Cam Menu item Notes This rotary encoder can be operated when the AW HESO is used It c
15. nnected Use a crossover cable when connecting the AV HS410 and VS R45 on a 1 1 basis 5 2 Functions Select the sub menu concerned from the Plug in menu and press F2 Open Menu to display the menu of the Plug in concerned MENU VS R45 IP The AV HS410 is subject to control exercised from the VS R45 IP For further details refer to the operating instructions of the VS R45 Notes The settings of the AV HS410 and VS R45 must be matched with the network settings The AV HS410 and VS R45 cannot be connected using a public line Panasonic Corporation 2011 2012 15
16. ower of the AV HS410 and then turn it back on again When the AV HS410 starts up the Plug in Software starts up automatically Notes e f the Plug in Software has not been started up the screen will go black even when the menu screen of the Plug in Software is opened e The Plug in Software will start up even when the AV HS410 is operating in the Service mode MENU Plug in Panasonic Corporation 2011 2012 5 Live Switcher AV HS410 Plug in Software lt How to operate the Plug in Software gt 1 CAM_IP This application makes it possible to control the pan tilt zoom focus and other functions from the AV HS410 once a Panasonic professional camera AW series has been connected to a network e The CAM_IP software runs in an AV HS410 model whose system software version is V2 00 00 or later If the system version of the AV HS410 is earlier than V2 00 00 upgrade it to V2 00 00 or later 1 1 Communication method Connect the camera to be controlled to the LAN connector on the rear panel of the AV HS410 using a LAN cable Use a crossover cable when connecting the AV HS410 and camera on a 1 1 basis Note The settings of the camera connected to the AV HS410 must be matched with the network settings Before connecting the units set the IP address of the camera to be connected and the port number using the Network sub menu The camera cannot be connected to the AV HS410 using a public line 1 2 Verified models AW HE50
17. to be exercised over the iris of the connected camera Manual The iris is controlled manually Auto The iris is controlled automatically 10 Live Switcher AV HS410 Plug in Software Item rotary encoder operated Sub menu Function CamCTL3 MEM Preset F2 This selects the memory in which the preset information of the camera is registered None Nothing selected MEM1 Use the memory registered in the PLUGIN MEM1 button MEM2 Use the memory registered in the PLUGIN MEM2 button e When the button for the memory previously selected in the MEM Preset item of the CamCTL3 submenu is pressed and its button is set to ON lighted the preset information of the commercial camera can be registered played back or deleted SHOT MEM El EVENT MEM 8 9 COPY DSBL STILL 2 REC PLUGIN MEM1 PLUGIN MEM2 Press a number key 1 to 10 after pressing the STORE button MEMORY WIPE PATTERN 10 KEY The preset information is registered in the number of the corresponding number key Hold down the number key Press a number key 1 to 10 after pressing the RECALL button Press a number key 1 to 10 after pressing the DEL button The preset information of the number corresponding to the number key is played back The preset information of the number corresponding to the number key is deleted Ho
Download Pdf Manuals
Related Search