Mojo Color Product User Guide
Contents
1. All Products Response Suspect three potential problem areas the power supply the lamp the fuse 1 Power supply Check that the unitis plugged into an appropriate power supply 2 The lamp Replacethe old lamp with a newone of appropriate specifications See directions above for replacing lamps 3 The fuse Replace the fuse See directions above for replacing the fuse No Response to DMX Response Suspect the DMX dip switch setting DMX cable orconnectors a controller malfunction a light effect DMX card malfunction 1 Check the DMX dip switch setting Make sure the DMX dip switch address setting is correct 2 Check the DMX cable Unplug the unit change the DMX cable resupply electrical power Try your DMX control again 3 Determine whetherthe controller or light effect is at fault Does the controller operate other DMX products properly If not take the controller in for repair If so take the DMX cable and the light effect toa qualified technician No Response to Audio 1 Check the function setting of the first unit Make sure that function dip switch 1 is on Function dip switch 1 on audio control 2 TurnUD the music volume Getting Ready All Geni products are thoroughly tested at the factory and shipped in perfect condition If damage has occurred during shipping orif components are missing please contact your Geni dealer immediately Your package should include 1 One Mojo Color color changer with2. Geni Electronics Co Ltd No 22 Chung Cheng 5 Street Yung Kang Tainan Hsien Taiwan Tel 886 6 253 8513 Fax 886 6 253 8685 Showroom Address Taipei World Trade Center Room 3A 04 No 5 Section 5 Hsin Yi Road Taipei Taiwan Tel 886 2 2722 2910 Get the Best Get Geni Fax 886 2 2722 2918 Geni Sets the Standard Appendix A DMX Dip Switch Value Guide DMX products must have their own address to receive DMX signals Addresses on MOC products are set by flipping appropriate DMX dip Switches To do this you need to know that DMX dip switches have the following values 1 1 2 2 3 4 4 8 5 1 6 32 7 64 8 128 9 256 And you need to know that DMX address settings are the sum of the dip switch values For example standard DMX addresses for four MOC changer each of which has four channels Follow MOC AddressValue DMX Dip Switches ON 1 Unit 1 1 Unit 2 2 2 Unit 3 3 1 2 Unit 4 4 3 Explanation Since each unithas fourchannels each address advances four values See Address Value above Once address values are figured out add DMX dip switch values to obtain the appropriate address DMX Dip Switches ON for each unit Flip appropriate DMX dip switches on each unit Mojo Color Product Guide DSS CMD NOM scsareatiatcsatarcetaringes E e E OS Page 1 WV AIIM serseri enee e e esa e eE Page 1 G tting FRE AG Y ocak cts os tives nee iceemi yom aa enina ai EE Page 2 Install Tine ery EL
3. bracket 2 One IEC electric mains power cord with plug 3 One product user manual The lamp may or may not be included depending on your GENI dealer In most cases the lamp is notincluded Install the Lamp ELC Mojo Color color changer use either the GX5 3 24V 250W lamp by Osram or the ELC lamp of identical specifications by Philips Use only the appropriate lamp for your unit Note that product versions that use other lamps may be offered in the future Check your product specification label for information Lamp Installation ELC 1 Loosen the two screws on the top ofthe lamp cover Open the case 2 Read lamp instructions Do nottouch the lamp bulb glass See Figure 1 Oil on hands shortens the lamp life If you touch the bulb glass wipe off the glass with aclean lint free towel and rubbing alcohol 3 Hold the lamp socket with one hand Insert the lamp pins into the holes in the lamp socket 4 Make sure thatthe leveris up Slide the lamp into the lamp base 5 Puton the lamp cover and fasten the screws snugly Lamp Items A Lever B ELC Lamp C Lamp Base D Lamp Socket E Lamp Pins Figure 1 IInstall the Lamp EHJ Mojo Color use either the HLX 64655 24V 250W lamp by Osram or the EHJ lamp of identical specifications by Philips Use only the appropriate lamp for your unit Note that product versions that use other lamps may be offered in the future Check your product spe
4. C J rrsreiiss enini denean iienaa Page 2 Lamp Installation ELC 5 u2 2s2eiecwanerelelad ner eadnseaane Page 2 Installing the Lamp Figure TD sc ciuseccccieescees tcivectoorcss Page 2 install the Lamp EHJ rssesiniicsosiniisnniinsnnniiniiinin Page 2 Lamp Installation Ed cc dees ciees onde armdvenceiins feeble Page 3 Installing the Lamp Figure 2 ic csscescuextcxeesscueeustetadax Page 3 Install the Lamp CT osc tase austen ceeandgexecsenyoncuaceeeued Page 3 Lamp Installation HTI S Page 3 Installing the Lamp Figure 3 eccc esenscesvecreegectaeweiveesess Page 3 Set Up and OPS alo wiiscsiiciacvidornsranectecavdss timenidacnerta Page 4 One unit Audio Bl CCl aciesccaciescnatenenatines ane seeeeessnatasanuds Page 4 Fo r nt PWG iesise ene siro EK RE AKOER ANE TEE Page 4 Four unit Audio Set Up Figure 4 Page 5 DMX COMMON essesi ERE EE Page 5 DMX Set Up Figure DS 0 cn2sdasccanesuttancesieetseceeaeenBanes Page 6 Product Operation OvervieW s ssssrsssrrrrsrsrsrsrn Page 6 Function Dip Switch CHAM iuscrnsetetontecapaiacteneccanaidas Page 7 DMX Channel CHa Ml cc cisniccedeonactasinntton ivecansisvantnireenaneee Page 7 A UMTS seserepan e iE Page 8 Changing igi dh 199 6 eae eee eee Aeron een Nene tema ene Page 8 Replacing the FUS so i gensc i e a Page 8 TROUDIE SIO MING coisa acerca ariel aenatciyatevesenuss Page 9 No Light No Movement All Products 55 Page 9 No Response to DMX conis capcetiveqsuGrrerteetaea
5. Mojo Color Product User Guide MOC MOC 150 Mojo Color One color wheel with 16 color G NI eee Geni Electronics Co Ltd THANK YOU Copyright 2001 Geni Electronics Co Ltd Thank you for buying a Geni Product specifications may be subject to change product For best results please For more information please visit carefully read and follow the http Awww beglec com directions in this product user manual Congratulations You have a great innovative product from Geni Electronics Co Ltd Geni Mojo Color changer make anyplace festive Whether you want simple plug amp play action or a sophisticated DMX show this product series has an effect oR m our for you ah S G N A Earth Ground You can rely on Geni Electronics Co Ltd for more excellent lighting products Dm B IEC power connector We design and manufacture strobes effects and mirrored projectors And new products are being launched regularly For information please visit our C Fuse holder web site at http www geni com tw We work hard to keep you our customer D 7 DMX signal Canon connector IN satisfied J E DMX signal Canon connector OUT You can get some of the best quality best priced products on the market from Fig ure 6 Geni So next time turn to Geni for more great lighting equipment Always get the best with Geni Appendix B Back Panel Thank you Geni Electronics Co Ltd Main Office Factory Address
6. as Reinsert the fuse cover Products are packed witha replacement fuse If your replacement fuse is missing anew onecan be purchased atan electric appliance store Be sure to use a fuse of the same type and specification See the product specification label for details Dip OFF Mode 1 Single unit show mode 2 Single unit audio mode 3 Single unit audio mode 4 Single unit audio mode 5 Single unit audio mode Function Dip Switch Chart ON Mode Single unit audio show mode 4 unit audio show mode master Self test mode Single slow show mode Focus assistance 6 1 unit audio mixed show Audio low BPM show mode 7 1 unit audio mixed show Audio high BPM show mode 8 Single unit audio mode No program 9 Single unit audio mode No program Applies only when audio mode Func dip switch on is activated Otherwise these channels are DMX address setting dip switches 209 255 160 208 150 159 140 149 130 139 120 129 110 119 100 109 90 99 80 89 70 79 60 69 40 49 30 39 20 29 10 19 2 0 9 Shutter 1 50 59 6 Mojo Color DMX Channel Chart 0000000 OZOD S CH1 Colors Strobe 1 flash per 4 seconds to 4fps Rotation slow fast Four color Square White amp Green Pink amp White amp Blue Blue amp White amp Green White amp Yellow Red amp White amp Orange Pink Circle Blue Circle Light Blue Circle Orange Circle Green Circle Yellow Circle Dark Gree
7. cification label for information 2 Lamp Installation EHJ 1 Loosen the two screws on the top of the lamp cover Open the case 2 Read lamp instructions Do not touch the lamp bulb glass See Figure 2 Oil on hands shortens the lamp life If you touch the bulb glass wipe off the glass with a clean lint free towel and rubbing alcohol 3 Glove your hand before installing the lamp Hold the lamp socket with one hand Insert the lamp pins into the holes in the lamp socket 4 Make sure that the lever is up Slide the lamp into the lamp base 5 Put on the lamp cover and fasten the screws snugly Remarks To replace the lamp using a small flat head screw driver to push thelamp outofthe lamp socket Lamp Items Lamp Socket Lamp Reflecto Lamp Flat head screw driver Figure 2 Install the Lamp MOC 150 MOC 150 usethe HTI152W lamp by Osram only Lamp Installation MOC 150 1 Make sure the unit is un plugged in advance Loosen the screws on the upper cover with a flat screwdriver open the upper cover 2 Use fingers to loosenscrew A B Cin sequence Hold onto screwA Cand pull backward See Figure 3 3 Hold onthe tube with gloved right hand The tube will be catapulted by pressing the lever D backward with left hand 4 Repeat procedure 1 amp 2 before installing the tube Insertthe pins of tube into the bottom of socket E Note The small holeis onlever D side 5 After installing the tube tigh
8. ctivate a slow paced four unit audio show See the following Function Channel Chart Do not activate audio dip switches on following units but set their DMX channels according to regular DMX procedures See Appendix A for an introduction to DMX dip switch settings One final note Terminate all systems by flipping on the Term dip switch on the last unit This preserves clear signal transmission in both audio and DMX modes
9. et Then plug a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link following units 3 Set DMX dip switches as follows MOC Dip ON Unit 1 1 Unit 2 2 Unit 3 1 2 Unit 4 3 For more units continue to use standard DMX dip switch settings See Appendix A for details 4 On the last in a series of units flip on the Terminate dip switch Term dip switch This keeps the signal clear Make sure other function dip switches are off 5 Supply electric power Plug electric mains power cords into each unit s IEC socket see figure 6 then plug the other end of the mains power cord into proper electric power supply sockets Do so for all units and the controller DMX Set Up Unit 3 Note Link all DMX cables and set dip switches before con necting electric power DMX Controller DMX OUT Figure 5 Do not supply power before the whole system is set up and connected properly 6 Design your show according to your DMX controller functions DMX channel functions are shown on pages 7 Product Operation Overview In audio mode Func dip switch on choose various shows by flipping regular dip switches on the first unit For example for a slow four unit audio show flip on Func dip switch on the first unit to activate audio mode then flip regular dip switches 2 and 6 on to a
10. iass Page 9 No Responseto A diOysescieesesm irens Page 9 Prod ct Specification Sasss mitais Page 10 Appendix A DMX Dip Switch Value Guide Page 11 Appendix B Back Panel Figure 6 000 Page 12 The lamp for MOC differs from that of MOC 150 beides this all other features between are the same In this manual all features description of MOC alos applies to MOC 150 Description Mojo Color Small color changer with high output great effect instant audio shows and DMX control Mojo Color One color wheel with 16 colors The setup control and functions of various Mojo Color may differ Please refer to specific product headingsin this manual Warning Like all electronic products Mojo Color changer lights must be used with common safety precautions in mind Mojo Color color changer lights contain no user serviceable parts Refer servicing to qualified technicians only Disconnect from electric mains power supply before removing covers or changing lamps Keep case closed while operating Do not insert objects into air vents Keep away from flames and flammable material Keep away from liquids Never operate in rain or in damp conditions If effect lights are dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating Lamp and metal become hot during operation Allow time to cool before handling Do not touch lamp b
11. n Circle Red Circle White Circle O Light unit automatically shuts off 5 seconds later 7 Set Up and Operation The setup and operation of all Mojo Color color changers is similar The main differenceis that function channels of various items vary so that dip switch settings differ slightly Follow directions below as they pertain to your particular product and your preferred operation mode Before plugging unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa One unit Audio 1 Fasten the effectlight onto firm trussing Use a 30 kg rated or stronger C clamp fastened onto the Mojo Color bracket Leave atleast one meter on all sides for air circulation 2 Flip on Func dip switch and dip switch 1 3 Plug one end of the electric mains power cord into the IEC socket on the unit See figure 6 page 12 Then plug the other end of the cord into a proper electric power supply socket 4 Turnon the music The scanner will change to the music Four unit Audio 1 Fasten the effectlight onto firm trussing Use a30 kg rated or stronger C clamp bolted onto the Mojo Color bracket Leave at least one meter on all sides for air circulation 2 Link the units as shown in figure 4 page 5 Connecta DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this pr
12. ocess tolink the second third and fourth units 3 Activate audio control On the first unit flip on Func dip switch Terminate the system On the last unit flip on Term dip switch 4 Set DMX dip switches as follows MOC Dip ON Unit 1 2 Unit 2 2 Unit 3 1 2 Unit 4 3 5 Supply electric power Plug electric mains power cords into each unit s IEC socket see figure 6 then plug the other end of the mains powercord into proper electric power supply sockets starting with the first unit Do not supply power before the whole systemis setup and connected Properly Four unit Audio Set Up DMX IN DMX OUT A FY PAHO ed Note Link cables and set dip switches before connecting electric power Figure 4 6 Turn on the music Note that up to 64 units can be connected and operated in audio mode To do so flip on DMX dip switch 1 on the 5th 9th 13th etc unit Then repeat settings on following units so 6th 10th 14th etc unit DMX settings unit 2 settings 7th 11th 15th etc Unit DMX settings unit 3 settings 8th 12th 16th unit settings unit 4 settings DMX Control 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp bolted onto the Mojo Color bracket Leave at least one meter on all sides for air circulation 2 Link the units as shown in Figure 5 Plug a DMX signal cable from the controller to the first unit s DMX in sock
13. ten up screw A amp C simultaneously next tighten up screw B Lock up the upper cover to get jobs done Figure 3 Maintenance Mojo Color color changers require almost no maintenance However you should Keep the unit clean Disconnect the mains power supply then wipe the cover witha damp cloth Do not immerse in liquid Wipe lens clean with glass cleaner and a soft cloth Clean internal components about once a year with a light brush and vacuum cleaner Do not use alcohol or solvents Keep connections clean Disconnect electric power then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power Changing the Lamp If electrical power is supplied andthe lamp does notlight itmay betime to change thelamp Replacing aFuse Power surges or inappropriate electrical power supply may cause a fuse to bum out If the fuse bums out the product will not function whatsoever If this happens replace the fuse as follows 1 Unplug the unit from electric power source 2 Inserta flat head screwdriver into a slotin the fuse cover C in figure 6 Gently pry up the fuse cover 3 Note two fuses The replacement fuse is covered The used fuse has both ends exposed Remove the used fuse If brownor unclear itis burned out 4 Push the replacement fuse out of its cover then insert the replacement fuse into the holder where the old fuse w
14. ulb glass with bare hands Read user manual instructions thoroughly before operating Follow the instructions Never remove warning or informative labels from the unit This appliance must be earthed Product Specifications Name Mojo Color Model MOC Voltage 230V 50Hz CE Power consumption 300W Fuse T3 15A Dimensions 280x220x160 mm Weight 6 kg Lamp 24V 250W ELC GX5 3 or 24V 250W EHJ G6 35 Name Mojo Color Model MOC 150 Voltage 230V 50Hz CE Power consumption 200W Fuse 5A Dimensions 280x220x160 mm Weight 6 7 kg Lamp HTI152W Name Mojo Color Model MOC Voltage 120V 50 60Hz Power consumption 300W Fuse T3 15A Dimensions 280x220x160 mm Weight 6 kg Lamp 24V 250W ELC GX5 3 or 24V 250W EHJ G6 35 Name Mojo Color Model MOC 150 Voltage 120V 50 60Hz Power consumption 250W Fuse 5A Dimensions 280x220x160 mm Weight 6 7kg Lamp HTI152W Versions for other lamps may be produced Please check the specification label on your product Product specifications may be subject tochange Please visit www geni com tw for details 10 Troubleshooting This troubleshooting guide is meant to help solve simple problems lf a problem occurs carry outthe steps below in sequence untila solution is found Once the unit operates properly do not carry out following steps If the effect does not operate properly refer servicing toa technician No Light No Movement
Download Pdf Manuals
Related Search