Presence sensor (light and motion sensor) Operating instructions
Contents
1. More information on the parameter settings can be found in the separate instructions for the Switch RC radio receiver Energy supply from solar cells batteries If daylight or artificial light is sufficient the sensor is powered by solar cells For immediate operation the energy storage unit must first be charged for approx 5 minutes at a minimum of 50 100 lux For light value measurement to function properly the energy storage unit must be charged for several days at a minimum of 50 100 lux The Test button can be used to check the operational readi ness of the presence sensor see Testing the operational readiness The presence sensor can optionally be operated with batteries if for example the sensor is located in a room with a very low light value lt 50 lux Construction The presence sensor is made up of the following components LRN button A for programming the presence sensor for the radio receiver e Test button B for sending a test signal e Light sensor C e Motion sensor D e Solar cells E e Test LED F for monitoring the operational readiness e Housing G with battery compartment Note The presence sensor cannot be used to manually switch the lighting on and off Because all switching functions and parameter settings of the presence sensor are executed via the Switch RC radio receiver the function of the presence sensor is only ensured2. Remove the old batteries Q Insert the new batteries 1 5 V Micro AAA ensuring that the polarity is correct Troubleshooting If you cannot remedy the fault please contact the customer service department of the manufacturer The device is not functional Is the energy storage unit sufficiently charged The device is functional but the switching functions are not being carried out e Is the device correctly programmed for the radio receiver Note See the separate instructions for the Switch RC radio receiver e Is the radio receiver switched off e Has the functional range been exceeded e Are the radio signals being disturbed by metal objects The device is carrying out an undesired functional mode Is the Mode parameter on the radio receiver set correctly Note See the separate instructions for the Switch RC radio receiver The setpoints of the functions are not being reached Are the Time and Light value parameters on the radio receiver set correctly Note See the separate instructions for the Switch RC radio receiver Appendix Technical data Transmission frequency 868 3 MHz Power supply Solar cells min 50 100 Ix 2 batteries to 50 Ix e 1 5 V Micro AAA e Service life 5 7 years Charge time for immediate operation Operating temperature Protection class Dimensions LxWxH Functional range Dimensioned drawing Approx 5 10 minutes
3. 10 C 50 C IP 50 108 x 108 x 26 8 mm Wood drywall 30 m max 5 walls Masonry 20 m max 3 walls Reinforced concrete 10 m max 1 wall ceiling The EMC requirements to EN 60669 2 1 are fulfilled Conformity with the relevant EU directives is confirmed by the CE symbol
4. OSRAM so Description Function and application SOLAR Presence sensor light and motion sensor Operating instructions Il 2009 SOLAR_ba0902en_we1 01 indd OSRAM GmbH Kunden Service Center Customer Service Center CSC Steinerne Furt 62 86167 Augsburg Germany Tel 49 0 1803 677 200 kostenpflichtig charges apply Fax 49 0 1803 677 202 www osram com www osram de 4008321385628 The SOLAR presence sensor detects the presence of people and measures the intensity of ambient light The energy supply for the presence sensor is provided by solar cells or if daylight or artificial light is insufficient by batteries The radio control system is primarily used to extend existing electrical installations without additional cabling Function The values measured by the presence sensor motion light value are transmitted to the Switch RC radio receiver via a ra dio signal The measured light value depends on the incidence of daylight the artificial lighting and the properties of the surface light dark The presence sensor is only ensured to function in combination with the radio receiver All switching functions and parameter settings of the presence sensor are executed via the radio receiver The following parameters can be set for every presence sensor programmed for the radio receiver e Delay switch off delay time if no motion is detected e Light value e Mode Note
5. in combination with the radio receiver Programming the sensor for the radio receiver The presence sensor can be programmed for a radio receiver and can be deleted again Proceed as follows Q Activate the programming mode of the radio receiver see the separate instructions of the Switch RC radio receiver Press the LRN button Then proceed as follows if persons were located within the de tection area when the presence sensor was being programmed Q Ensure that all persons leave the detection area of the pres ence sensor Enter the detection area again after at least 2 minutes elapse Result The presence sensor sends an ON signal and functions properly Continued on the back page Operation cont Testing the operational readiness For solar operation the energy storage unit must be sufficiently charged see Energy supply via solar cells batteries To check the operational readiness proceed as follows Press the Test button The presence sensor sends a test signal Check whether the Test LED is lit up e LED is lit the presence sensor is operational e LED is not lit the presence sensor is not operational Continue charging the energy storage unit if the presence sensor is not yet operational Replacing the batteries The batteries need to be replaced every 5 7 years Proceed as follows Open the battery compartment on the back of the presence sensor
Download Pdf Manuals
Related Search