INSTALLATION MANUAL
Contents
1. counter harness four screws AOW4IXCO08DA 8 Attach the working table to the machine three screws removed in step 1 9 Remove the cap from the working table at one place YY 0 AOW4IXCO10DA 10 Attach the mounting plate of the key counter mount kit to the working table two screws removed in step 6 o A0W4IXC011DA E 3 Installation Manual 11 Attach the socket to the mounting plate two screws furnished with the key counter mount kit 14 Attach the cover to the mounting plate two screws furnished with the key counter mount kit AOW4IXC012DA AOW4IXCO16DA Insert the harness into the wire saddles at two places located on the underside of the working table and run the connector through the hole and remove the connector cover AOW4IXC013DB 13 Insert the socket harness into the edge cover at one place and connect the socket connector to the connector from the machine AOW4IXC015DA Installation Manual 15 Attach the cover for the key counter harness that was removed in step 6 two screws removed in AOW4IXC017DA E 4 Y110451 0 WT 506 Working Table INSTALLATION MANUAL Applied Machines d Color MF651 MF551 MF451 COLOR MFP 65 ppm 55 ppm 45 ppm Product Code AOPO AOP1 A0P2 I Accessory parts Installing the working table No Name Using nippers pull out the k2. materials and keep them out of the reach of children Putting the head in the plastic bag involves danger of suffocation Y110451 0 E 1 Installation Manual Il Installation procedures 1 Remove the knockouts at three places from the IR right upper cover using nippers AOYEIXC023DA AOYEIXC024DA 3 Insert tabs at three places on the working table into the holes in the machine and slide the work ing table in the direction of the arrow AOW4IXC002DA Installation Manual E 2 4 Secure the working table three screws furnished with the working table AOYEIXC025DA lt When installing the key counter mount kit gt 1 Remove the working table three screws 2 Remove the three screws from the IR right upper cover AOYEIXCO026DA 3 Remove the IR right upper cover and remove the knockout at one place using nippers AOYEIXC027DA Y110451 0 Y110451 0 4 Remove the harness from the wire saddles at three places 7 Run the harness through the hole on the working table as shown in the illustration below N AOYEIXC028DA AOW4IXCOO9DA 5 Attach the cover removed in step 3 three screws Run the harness through the hole made in step 3 AOYEIXC029DA 6 Remove screws from the underside of the work ing table and remove the cover for the key
3. 11DA 14 Attach the socket to the mounting plate with two screws that are included in the kit AOW4IXC012DA 15 Insert the harness into the wire saddles at two places located on the underside of the working table Run the connector through the hole and remove the connector cover AOW4IXC013DB Installation Manual 16 Insert the socket harness into the edge cover at one place and connect the socket to the con nector from the machine AOW4IXC015DA 17 Attach the cover to the mounting plate with two screws included in the kit AOW4IXC016DA 18 Attach the cover for the key counter harness that was removed in step 9 with two screws removed in step 9 AOW4IXC017DA Installation Manual E 8 Y110451 0
4. WT 506 Working Table INSTALLATION MANUAL Index WT 506 d Color MF360 MF280 MF220 Accessory parts Il Installation procedures WT 506 d Color MF651 MF551 MF451 Accessory parts Il Installing the working table Y110451 0 E i Installation Manual This page is intentionally left blank Installation Manual E ii Y110451 0 WT 506 Working Table INSTALLATION MANUAL Applied Machines d Color MF360 MF280 MF220 COLOR MFP 36 ppm 28 ppm 22 ppm Product Code AOED Accessory parts Note This manual provides the illustrations of the acces No Name sory parts and machine that may be slightly differ 1 Working table ent in shape from yours In that case instead of the illustrations use the appearance of your machine to follow the installation procedure This does not cause any significant change or problem with the procedure AOW4IXCO18DA Screw 4 x 16 mm 7 9J08IXCO75DA Cord clamp 1 AOW4IXC019DA Cable tie 2 4551IXC007DB Cushion 2 A0W4IXC020DA Authentication _ 1 Keep the cord clamp properly for use when mounting the authentication unit 2 Be sure to keep the cable tie cushion and authentication label that are necessary for instal lation of the authentication unit AU 201 They are kept inside the cover located on the under side of the working table A WARNING After unpacking be sure to get rid of the D packaging
5. nockouts three i knockouts from the right side surface of the 1 Working table machine AOW4IXC018DA Screw 4 x 16 mm 7 9J08IXCO75DA Cord clamp 1 AOW4IXC019DA Cable tie 2 S 4551IXC007DB Cushion 2 A0W4IXC020DA Authentication Q label 2 i A0W4IXC022DA 3 Insert tabs three knockouts on the working table 1 Keep the cord clamp properly for use when into the holes in the machine and slide the work mounting the authentication unit ing table in the direction of the arrow 2 Be sure to keep the cable tie cushion and authentication label that are necessary for instal lation of the authentication unit IC card type They are kept inside the cover located on the underside of the working table After unpacking be sure to get rid of the packaging materials and keep them out of 1 the reach of children Putting the head in the plastic bag i AOW4IXC002DA involves danger of suffocation Y110451 0 E 5 Installation Manual Secure the working table three screws furnished with the working table AOW4IXCO03DA lt When installing the key counter mount kit gt 1 Remove the working table three screws 2 Remove three screws that hold the right side cover of the machine Remove one screw that holds the right rear cover in place AOW4IXC004DB While moving the
6. right side cover in the direction of the arrow remove the cover Remove the Knockout AOW4IXC021DA Installation Manual E 6 4 Open the right door of the machine 5 Remove the harness from the wire saddles at five places and the edge cover at one place Edge cover Wiring sadle AOW4IXCOOSDA 6 Insert the harness into the wire saddle at one place and the edge cover at one place Wiring sadle Edge cover AOW4IXCOO6DA 7 Attach the right side cover removed in step 3 with four screws Run the harness through the hole made in step 3 AOW4IXC007DA Y110451 0 8 Close the right door of the machine 9 Remove four screws from the underside of the working table Remove the cover for the key counter harness with four screws AOW4IXCO08DA 10 Run the harness through the hole on the working table as shown in the illustration below AOW4IXCOO9DA 11 Attach the working table to the machine with three screws removed in step 1 12 Remove the cap from the working table at one place LY 0 AOW4IXCO10DA Y110451 0 E 7 13 Attach the mounting plate that is included in the key counter mount kit to the working table with two screws removed in step 9 o A0W4IXC0
Download Pdf Manuals
Related Search