Micro11 68HC11 Monitor Program User's Manual
Contents
1. B will place the cursor in the appropriate CPU register You must type 2 or 4 digits as required simply editing the value displayed will not work There is no way of modifying the contents of the condition code register In all cases backspace and escape are supported Each of the pointer registers has a 5 byte data area associated with it The data bytes shown are 5 bytes in memory starting at the address specified in the pointer Note that using a pointer to point to an I O device can have undesirable side effects in the CPU window since the I O device will be read every time the CPU window is redrawn If you have unused pointer registers you can use them to display any memory you wish Therefore you can display any ram data without having to exit to Micro11 s memory display function The contents of the CPU window are refreshed after every program step and can be refreshed by pressing the space bar Note that the CPU window is NOT refreshed when breakpoints are inserted and deleted Tracing One Instruction To single step trace through one instruction simply press T After the instruction is complete the CPU window will be refreshed Do NOT attempt to trace through Output Compare 5 routines as both you and Micro11 will be competing for these resources and Micro11 may crash Holding T down will cause a continual series of traces Important information for advanced programmers Starting with Version 1 03 it is possible to trace2. Micro11 68HC11 Monitor Program User s Manual by Grant Beattie Micro11 Version 1 03 Manual Revision May 1995 Introduction A monitor is a simple operating system which provides 1 O facilities and the ability to load run and debug user programs Micro11 is a monitor program for use with the 68HC11 Development Board It is resident in a 27128A EPROM and in conjuction with a terminal or personal computer provides the following services e Downloading user programs from a PC in either Motorola or Intel formats e Memory examine modify facilities including EEPROM e Program run facilities e Integrated breakpoint trace and CPU register examine change window e CPU vector display and on board ROM self test Micro11 is a menu driven monitor which uses VT 100 ANSI command codes to provide a modern user interface over the RS 232 serial link Operating Environment To take full advantage of Micro11 s features the following hardware is required as part of the 68HC11 Development Board e Micro11 must be located at C000 FFFF e Micro11 uses RAM in the range of 7F00 7FFF and Micro11 expects to load the stack pointer e The HC11 must use a 4 9152MHz crystal e PA3 OC5 must be connected to XIRQ only used for trace function A terminal or PC running a VT 100 compatible communications program such as PROCOMM is also required Because Micro11 makes extensive use of VT 100 command codes it is recommended that the communication li
3. ecord or Intel Hex format may be downloaded from a PC Download Menu Motorola S Record Intel Hex File Default Download File Name Current filename 341lab8a s19 Default Filename Download Default This feature is only applicable to PC s equipped with recent versions of PCPLUS When the user requests a file upload on the PC PCPLUS will examine the current PC screen for some text separated by a period When it prompts you for a file to upload it uses the text it found as a default if it found any The purpose behind this function on the 68HC11 is to give the user the ability to place text on the screen Thus when uploading a file repeatedly from a PC it is only necessary to enter the file name once In the example below the user has entered 341LAB8a S19 Whatever name you choose you must have a period Drive names will be rejected by PCPLUS therefore only 11 characters plus the period are permitted Download Menu Procomm looks on the screen for text to use as a filename Use the form FILENAME EXT 341lab8a S19 Micro11 User s Manual 5 May 1995 Motorola Download Motorola Motorola S19 files are uploaded from the PC and downloaded to the 68HC11 using this command After selecting M the following menu appears Download Menu Motorola S Record Intel Hex File Default Download File Name Current filename 341lab8a s19 68HC11 Waiting for File The 68HC11 will wait forever for the file Press PgUp on the PC and se
4. nd the S19 file as a RAW ASCII file When the transfer is complete control will return to Micro11 To abort the transfer press RESET on the 68HC11 board or press Esc on the PC The default filename is optional Intel Download Intel Intel Hex files are uploaded from the PC and downloaded to the 68HC11 using this command After selecting I the following menu appears Download Menu Motorola S Record Intel Hex File Default Download File Name Current filename 341lab8a hex 68HC11 Waiting for File The 68HC11 will wait forever for the file Press PgUp on the PC and send the hex file as a RAW ASCII file When the transfer is complete control will return to Micro11 To abort the transfer press RESET on the 68HC11 board or press Esc on the PC The default filename is optional Micro11 User s Manual 6 May 1995 Memory Menu Pressing M from the Main Menu brings up the memory sub menu Memory Menu Dump Display Memory Block Examine Individual Locations Fill Copy Memory Block Modify Memory Register Locations Dump Memory Dump Displays 256 bytes of RAM or ROM in hex and ASCII After choosing memory dump you will be prompted for a starting address Display Memory Block Enter Starting Address 0000_ After entering a 4 digit starting address press Enter To view the NEXT 256 locations press the space bar Pressing any other key returns control to the Main Menu Micro11 User s Manual 7 May 1995 Examine Memory Exami
5. ne Used to examine individual memory or register locations After choosing memory examine you will be prompted for a starting address Examine Individual Locations lt ADDRESS gt for specific location lt N gt lt RET gt for next address lt RETURN gt to exit Address C000 Value FC Address _ After entering a 4 digit address press Enter To view the NEXT location press N Enter To view a different address simply enter that address To quit press Enter or Esc Be aware that examining some types of I O can have side effects Try examining 9000 Since the LED is a write only device examining it may give unpredictable results depending on whether or not it was decoded using R W Modify Memory Modify Used to modify individual memory or register locations After choosing memory modify you will be prompted for a starting address Modify Memory Register Location s lt ADDRESS gt for specific location lt N gt lt RET gt for next address lt RETURN gt to exit Address 9000 Value 21 Done Address _ After entering a 4 digit address press Enter and then enter a 2 digit byte value To modify the NEXT location press N Enter To modify a different address simply enter that address To quit press Enter or Esc Modifying EPROM will have no effect Micro11 User s Manual 8 May 1995 Fill Copy Menu Pressing F from the Memory Menu brings up the Fill Copy sub sub menu Since fill and copy are seldom used they ha
6. nk be at 4800 baud or higher Micro11 User s Manual 3 May 1995 Micro11 Main Menu All menu choices are made by selecting one of the highlighted characters present usually the first letter of a choice Address and data input is in HEX Upper and lower case entry is accepted for both menu and data input Other characters will be rejected and the user must re enter the information Esc will typically abort the current command and return control back to the menu Backspace is supported for correcting address and data entry Upon powering up Micro11 a greeting panel will appear once Pressing any key will bring up the Main Menu Pressing hardware RESET will take the user back to the Main Menu not the greeting The only way to re display the opening greeting is by executing the Options Cold Reset command or by cycling the power to the 68HC11 Development Board The Main Menu Micro11 68HC11 Monitor Program Main Menu Download Motorola or Intel Hex File Memory Dump Examine Fill Modify Options Cold Boot Vectors ROM Test Run Program or Subroutine Window Trace Breakpoint Window Choosing D M O R or W will bring up the appropriate sub menu The following pages explain the operation of every Micro11 command All commands which appear under a given sub menu are discussed as a group Micro11 User s Manual 4 May 1995 Download Menu Pressing D from the Main Menu selects the download sub menu User programs in either Motorola S R
7. o the user subroutine in a manner similar to Run Program Prior to the subroutine execution a return address is pushed on the system stack When the user subroutine executes RTS the return address is pulled into the PC and control is returned to Micro11 Subroutine Run Enter Starting Address _ Micro11 User s Manual 16 May 1995 Trace Breakpoint Window Breakpoint trace single step and CPU register examine modify functions have been collected into a common interface called the Trace Breakpoint Window Within this window there are two distinct areas The CPU WINDOW is used for the management of the CPU registers and for controlling program execution step or run The BREAKPOINT WINDOW is used for setting and removing breakpoints The Trace Breakpoint Window 68HC11 CPU WINDOW TEST PC 1040 gt 00 00 00 00 P Y X A B Modify CPU Registers derek nearer rey PCr Trace One Instruction 7F6A gt 00 00 00 00 Gorei as Go to next RTS a scrusansacuanaanaetacuet Run Program from PC 1040 gt 00 00 00 00 ESC ee Exit to Main Menu X 1040 gt 00 00 00 00 Nisa renar Set Multiple Trace Number 0000 B Mre Execute Multiple Trace NZVC 01 Current Multiple Trace Count hex CCR 00 0000 BREAKPOINT WINDOW Breakpoint 1 fea Breakpoint 2 Ls al Clear Breakpoint Breakpoint 3 a Set Breakpoint Breakpoint 4 e Selection _ Micro11 User s Manual 17 May 1995 Modifying Registers Pressing P X Y A or
8. re 5 7FE2 0000 O P Compare 3 7FD8 0000 7FDC 0000 7FEO 0000 7FE4 0000 SCI Interrupt Pulse I P Edge Timer Overflow O P Compare 4 I P Capture 3 7FEA I P Capture 2 7FEC 0000 O P Compare 2 7FE6 0000 O P Compare 1 7FE8 0000 0000 I P Capture 1 7FEE 0000 RealTime Int 7FFO 0000 IRQ Interrupt 7FF2 0000 XIRQ Interrupt 7FF4 D037 SWI Interrupt 7FF6 0000 IllegalOpcode 7FF8 CFAE COP Watchdog 7FFA 0000 Clock Monitor 7FFC 0000 There is a special hook that allows your program to run right out of RESET This is to allow user programs in SRAM to run once immediately from RESET to gain access to the 64 time protected registers Briefly what you must do is place the two byte address 0x1040 at address Ox7FFE Following the next RESET execution will start at 1040 instead of OxC000 See your instructor for more details Micro11 User s Manual 12 May 1995 Rom Test Options Rom Test The on board rom test prompts the user for a starting and ending address over which to perform the test The test is a Cyclic Redundancy Check Kontron Algorithm After accepting the second address the cursor moves down one line and the test proceeds When running the test over the range C000 FFFF the test execution time is approximately 10 seconds Cyclic Redundancy Check Enter Starting Address C000 Enter Ending Address FFFF EPROM CRC Checksum B48C Press any key to contin
9. te any single EEPROM byte For best EEPROM life expectancy Motorola recommends that any byte to be written should be blank first FF The Erase EEPROM byte command can be used for that purpose After choosing Write EEPROM byte you will be prompted for the address of the byte and then the value to write Enter Address to WRITE B600 Vaule to Write 47 Done Set SCI baud rate Options EEPROM SCl The user s default baud rate is maintained in EEPROM memory location B7FF The erased state of this location is FF and will result in a baud rate of 9600 The various baud rates are derived from the 4 9152MHz system clock and the various choices are SCI Baud Rate Menu 19 2 kbaud 9600 baud 4800 baud 2400 baud 1200 baud ok ON Selection _ Micro11 User s Manual 15 May 1995 Run Menu Selecting R from the Main Menu brings up the Run Menu Complete user programs or individual subroutines can be executed from the Run Menu Run Menu Program Run Subroutine Run Program Run Run Program Complete execution is handed over to the user program The stack pointer is managed by Micro11 and need not be initialized in the user program If you intend to use breakpoints do not initialize the stack pointer in your program Breakpoints will be trapped by Micro11 and control will be turned over to the Trace Breakpoint Menu Program Run Enter Starting Address 1040_ Subroutine Run Run Subroutine Complete execution is handed over t
10. the G command Execution will NOT occur in real time since Micro11 inspects every opcode before it is executed to determine if the opcode is RTS If the opcode is RTS control is returned to the CPU window If it is not it is executed normally Setting Breakpoints Micro11 supports up to four breakpoints BREAKPOINTS MUST BE SET AT OPCODES When a breakpoint is set the target opcode is replaced by an illegal opcode 41 Thus when the CPU attempts to execute the illegal opcode control is returned to Micro11 AND THE BREAKPOINT IS REMOVED The status of all 4 breakpoints is indicated on the screen When a breakpoint is set the CPU Window is NOT redrawn If you wish to redraw the CPU Window to look at a breakpoint in memory for instance press the space bar To insert a breakpoint simply press S followed by a number 1 to 4 and the address of the target opcode Micro11 User s Manual 19 May 1995 Clearing Breakpoints Since breakpoints are cleared removed when they are encountered one normally does not need to clear them If you wish to clear a breakpoint press C followed by the number of the breakpoint you wish to clear The illegal opcode 41 will be removed and the original opcode restored NOTE If a user breakpoint exists and then the user presses RESET the breakpoint opcode 41 will be left stranded in the user code Re download your program or fix the opcode by hand Micro11 User s Manual 20 May 1995
11. through programs which have interrupts occuring in the background An example of this would be a main program that runs concurrently with several Output Compares which are interrupt based It will be possible to trace through the main program since Micro11 allows for nested interrupts You should avoid using OC5 for the same reasons given above Also very high frequency interrupts may tax Micro11 s ability to service all pending interrupts If your interrupt rate is too high it will appear as though tracing is stuck on one instruction Micro11 User s Manual 18 May 1995 Tracing More than One Instruction If you wish to step through larger pieces of code than one instruction a Multiple Trace Count Number can be specified After specifying the number the default is one instruction executing a Multiple Trace will cause that number of instructions to be executed Since the number is specified in HEX the range is 1 to 255 instructions The number of steps is always visible in the CPU window as the Current Multiple Trace Count Running a Program Running a program in the CPU Window is identical to running a program in the Micro1 1 Run Program function see page 13 The only difference is that you will not be prompted for a program counter value Execution will begin at the PC value visible on the screen Control is completely turned over to the user program Go to next RTS If you wish to execute to the end of a subroutine you may use
12. ue Micro11 User s Manual 13 May 1995 EEPROM Menu Pressing E from the Options Menu brings up the EEPROM Operations sub sub menu Since EEPROM operations are seldom used they have been given a separate menu underneath the Options sub menu Also since EEPROM is read mostly memory procedures such as writing erasing EEPROM locations should be carefully considered NOTES e EEPROM memory consists of B600 B7FF and the CONFIG byte at 103F e Beware Modifying the contents of 103F could render your HC11 chip useless e Micro11 uses EEPROM location B7FF to store the user s baud rate The erased state of this byte FF will produce a baud rate of 9600 EEPROM Menu Erase EEPROM byte Bulk erase EEPROM Write EEPROM byte Set SCI baud rate Erase EEPROM byte Options EEPROM Erase Used to erase any single EEPROM byte For best EEPROM life expectancy Motorola recommends that any byte to be written should be blank first FF This command can be used for that purpose After choosing Erase EEPROM byte you will be prompted for the address of the byte to erase Enter Address to ERASE B600 Done Micro11 User s Manual 14 May 1995 Bulk Erase EEPROM Options EEPROM Bulk Used for bulk erasing the entire 512 byte EEPROM array but not the config byte After choosing Bulk Erase EEPROM you will be asked to confirm your intention Bulk ERASE all 512 bytes Y N _ Done Write EEPROM byte Options EEPROM Write Used to wri
13. ve been given a separate menu underneath the memory sub menu Both fill and copy are intended to operate on large blocks of RAM Fill Copy Menu Fill Memory Block Copy Memory Block Fill Memory Fill Fill Fills a block of RAM specified by a starting and ending address with a constant hex value Fill Memory Block Enter Starting Address 0000 Enter Ending Address OOFF Fill Value 12 Done After the operation is complete control returns to the Main Menu The operation can be aborted by pressing Esc Filling EPROM will have no effect Micro11 User s Manual 9 May 1995 Co Memory Fill Co Copies a block of RAM specified by a starting and ending address to a new target location Copy Memory Block Enter Starting Address 2000 Enter Ending Address 20FF Enter Target Address 2100 Done After the operation is complete control returns to the Main Menu The operation can be aborted by pressing Esc Micro11 User s Manual 10 May 1995 Options Menu Several miscellaneous commands have been gathered together under the Options sub menu Options Menu Cold Reset Vector Display EEPROM Operations Rom Test CRC Cold Reset Options Cold Reset Reinitializes the monitor program which deletes the default download filename and resets the status of the Trace Breakpoint function This serves the same purpose as cycling the power to the 68HC11 except that the contents of ram are not disturbed The opening greeting is displa
14. yed Vector Displa Options Vector Displa Shows the current target addresses for each of the interrupt vectors The interrupt vectors are maintained in RAM except for RESET so that they may be modified by the user while the Micro11 EPROM is in place Micro11 uses an illegal opcode 41 for breakpoints and XIRQ for the trace function The vectors for XIRQ and Illegal Opcode are written to the appropriate locations in ram when the user enters the Trace Breakpoint window Therefore if you have written your own XIRQ and or Illegal Opcode interrupt service routines it is important that you NEVER enter the Trace Breakpoint facility Micro11 User s Manual 11 May 1995 Before ever entering the Trace Breakpoint Menu Vector Display RESET 7ffe C000 SCI Interrupt 7FD6 0000 SPI Interrupt 7FD8 0000 Pulse I P Edge 7FDA 0000 Pulse Overflow 7FDC 0000 Timer Overflow 7FDE 0000 O PCompare5 7FEO 0000 O P Compare 4 7FE2 0000 O P Compare 3 7FE4 0000 O P Compare 2 7FE6 0000 O P Compare 1 7FE8 0000 I P Capture 3 7FEA 0000 I P Capture 2 7FEC 0000 I P Capture 1 7FEE 0000 Real Time Int 7FFO 0000 IRQ Interrupt 7FF2 0000 XIRQ Interrupt 7FF4 0000 SWI Interrupt 7FF6 0000 Illegal Opcode 7FF8 0000 COP Watchdog 7FFA 0000 Clock Monitor 7FFC 0000 After entering and leaving Trace Breakpoint Window Vector Display RESET 7ffe C000 7FD6 0000 SPI Interrupt 7FDA 0000 Pulse Overflow 7FDE 0000 O P Compa
Download Pdf Manuals
Related Search