Home

EW-7208APC User Manual

1. AP Bridge WDS Security Setting Encryption WPAPre shared Key Y WPA Unicast Cipher Suite wPA2 AES Pre shared Key Format Passphrase Pre shared Key EH Wireless Security Wireless Security Encryption WEP Key Length 64 bit Key Format Hex 10 characters Encryption Key eee eee oe Hide Enable 802 1x Authentication Select an encryption type from the drop down menu A WPA Pre shared Key is the recommended and most secure encryption type A In WISP mode WPA RADIUS is unavailable for the wireless band that is used to connect to WISP s AP Wireless Security Encryption Disable 7 Enable 802 1x Authentication WPA Pre shared Key WPA RADIUS 111 4 5 1 1 Disable Encryption is disabled and no password key is required to connect to the EW 7208APC A Disabling wireless encryption is not recommended When s disabled anybody within range can connect to your device s SSID Enable 802 1x Check the box to enable the 802 1x Authentication authentication A RADIUS server is required to perform 802 1x authentication enter the RADIUS server s information in the relevant fields below V Enable 802 1x Authentication RADIUS Server IP address RADIUS Server Port 1812 RADIUS Server Password 111 4 5 1 2 WEP WEP Wired Equivalent Privacy is a basic encryption type For a higher level of security consider using WPA encryption Wireless Security Encryption WEP
2. Configuration The configuration mode of the device s WPS Mode setting is displayed here Registrar means the device acts as an access point for a wireless client to connect to and the wireless client s will follow the device s wireless settings Configure via Push Click Start PBC Push Button Configuration Button to activate WPS on the access point WPS will S be active for 2 minutes Configure via Client Enter the wireless client s PIN code here and PIN Code click Start PIN to activate PIN code WPS Refer to your wireless client s documentation if you are unsure of its PIN code lll 3 A 4 Access Control Access Control is a security feature that can help to prevent unauthorized users from connecting to your wireless router This function allows you to define a list of network devices permitted to connect to the EW 7208APC Devices are each identified by their unique MAC address If a device which is not on the list of permitted MAC addresses attempts to connect to the EW 7208APC it will be denied To enable this function check the box labeled Enable Wireless Access Control Access Control Enable Wireless Access Control MAC Address Comment Add Select MAC Address Device Name IP Address Select aa bb cc dd ee ff OFFLINE OFFLINE Edimax Save Settings MAC address Select a PC name from the drop down list and click gt gt to add enter it into the blank field to the
3. edimax 5G 036155 Channel Number 1 Channel Number 40 Security WPA2 AES Security WPA2 AES MAC Address 74 04 38 03 61 50 MAC Address 74 04 38203 61 55 Ill 2 Save Settings 1 After you configure any settings click the Save Settings button at the bottom of the screen to save your changes Save Settings A The device needs to restart in order to bring any changes into gt effect 2 Then click click here to restart in order to restart the device and bring the changes into effect Settings have been saved Pleag click here to restart ye router and bring the new settings into effect 3 To make several changes at once use the Save Settings button after each change and then click click here to restart after your final change Only one restart is necessary as long as each change is saved with the Save Settings button A After you click click here to restart all saved changes will come gt nto effect Ill 3 Main Menu Access Point Mode The main menu displays different options depending on your device s operating mode The default access point mode menu is described below with other modes in the following chapter IIl 4 Main Menu Other Modes Access Point Status Setup Wizard LAN 2 4GHz Wireless 5GHz Wireless Advanced Administration 111 3 1 Status The Status page displays basic system information Status pag Pay d about the device
4. PY 1 Usethe checkboxes to select which day s to include in the schedule 2 Specify a time hour and minute for the schedule using the drop down menu 3 Select which command applies to this schedule from the drop down menu either Wireless On or Wireless Off Add the schedule to the table of active schedules Active schedules will be displayed in the table as shown below Select an entry using the Select checkbox Monday Tuesday Wednesday Thursday Friday 01 00 wireless off E Monday Tuesday Wednesday Thursday Friday 08 00 wireless on E Delete Selected Delete All Save Settings Settings hawe been sawed Please click here to restart the router and bring the new settings into effect Delete Selected Delete selected or all entries from the table Delete All 111 4 6 Firewall The Firewall menu provides access to URL blocking dy Firewall access control DMZ and DoS functions to improve URL Blocking the security of your wireless network Access Control DMZ DoS Firewall The router provides stateful packet inspection SPI firewall protection Only packets matching a known active connection will be allowed by the firewall others will be rejected SPI firewall Enable Disable Enable or disable the Stateful Packet Inspection SPI firewall Ill 4 6 1 URL Blocking This function can block Internet access by either specific URLs or keywords Check uncheck the Enable URL Block
5. Key Length 64 bit Key Format Hex 10 characters e Encryption Key ssssscese 4 Hide Enable 602 1x Authentication Key Length Select 64 bit or 128 bit 128 bit is more secure than 64 bit Key Format Choose from ASCII any alphanumerical character 0 9 a z and A Z or Hex any characters from 0 9 a f and A F Encryption Key Enter your encryption key password according to the format you selected above A complex hard to guess key is recommended Check the Hide box to hide your password from being displayed on screen Enable 802 1x Check the box to enable the 802 1x Authentication authentication A RADIUS server is required to perform 802 1x authentication enter the RADIUS server s information in the relevant fields below V Enable 802 1x Authentication RADIUS Server IP address RADIUS Server Port 1812 RADIUS Server Password Ill 4 5 1 3 WPA Pre Shared Key WPA pre shared key is the recommended and most secure encryption type Wireless Security Encryption WPA Pre shared Key WPA Unicast Cipher Suite WPA TKIP CO WPA2 AES WPA2 Mixed Pre shared Key Format Passphrase Pre shared Key 4 Hide WPA Unicast Select from WPA TKIP WPA2 AES or WPA2 Cipher Suite Mixed WPA2 AES is safer than WPA TKIP but not supported by all wireless clients Please make sure your wireless client supports your selection WPA2 AES is recommended followed by WPA2 Mixed if your client does not
6. 1 Enable 5GHz 2 Enable 2 4GHz 4 Select the Wi Fi network name SSID which you wish to connect to for the specified frequency and click Next to continue A If the Wi Fi network you wish to connect to does not appear try Clicking Refresh Range Extender 5GHz Wireless Site Survey The range extender is surveying all available routers nearby Please select the router you wish to connect to If the router you wish to connect is not listed try clicking Refresh To connect to a hidden SSID please select Setup extender manually C Setup extender manually Ld 6208ac 5G 100 A CAP1200 ac 100 MIS Jacky 5G 10096 OBM Dlink817 5G 100 EdimaxHQ 5G 92 To connect to a hidden SSID check the Setup extender manually A box and enter the details manually on the next page as shown below Range Extender 5GHz Wireless Site Survey Please set a new Wi Fi network name SSID for the range extender if you wish and set the security key for your existing wireless network if required Wi Fi network name SSID Range extender SSID Encryption WPA2 Y Security Type TKIP AES Key Format Passphrase Wi Fi password Security Key E D Enter your existing wireless network s security key password in the Security Key field and click Next to continue Range Extender 5GHz Wireless Site Survey Please set a new Wi Fi network name S
7. Install istal Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks OK Cancel 2 Select Obtain an IP address automatically and Obtain DNS server address automatically should be selected General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Subnet mask Defa gateway Preferred DNS serve Alternate DNS server IV 1 1 3 Windows 7 1 Click the Start button it should be located in the lower left corner of your computer then click Control Panel l Getting Started E Windows Media Center a S Calculator m Sticky Notes EA Snipping Tool Ey Paint a Remote Desktop Connection E Magnifier a e Solitaire gt All Programs Search programs and files gt EJ Control Panel Adjust your computer s settings System and Security Review your computer s status Back up your computer Find and fix problems Network and Interne View network status and tasks Choose homegroup and sharing opt View devices and printers Add a device Programs Uninstall a program 3 Click Local Area Connection Edimax Documents Pictures Music Games Computer Control
8. Short Preamble Long Preamble Auto Always None 100 9 Auto Save Settings radio The default value is 2346 The default value is 2347 The default value is 100 default value is 3 default is set to Auto N Data Rate Set the data rate of 802 11n The default is set to Auto Channel Width Preamble Type CTS Protect Select wireless channel width bandwidth used by wireless signals from the device the recommended value is Auto 20 40MHz Set the wireless radio preamble type The default value is Short Preamble Enabling this setting will reduce the chance of radio signal collisions between 802 11b and 802 11g wireless access points It s recommended to set this option to Auto Set the power output of the wireless radio You may not require 10096 output power Setting a lower power output can enhance security since potentially malicious unknown users in distant areas will not be able to access your signal WMM Wi Fi Multimedia technology can improve the performance of certain network applications such as audio video streaming network telephony VoIP and others When WMM is enabled the device will prioritize different kinds of data and give higher priority to applications which require instant responses for better performance lll 4 8 5 5GHz Wireless These settings are for experienced users only Please do not change any of the values on this page unless you are already familiar with the
9. Total Upload Bandwidth D kbits Current QoS Table Priority Rule Name Upload Bandwidth Download Bandwidth EU Es Ee ee Save Settings Total Download Enter your total download bandwidth limit Bandwidth from your Internet service provider ISP in kbits Bandwidth your Internet service provider ISP in kbits to the current QoS table Local QoS This page allows users to add modify the QoS rule s settings Rule Name Bandwidth IP Address Local Port Range Remote Remote T Bandwidth Local IP Address IP Address Port Range Protocol raffic Type Download kbits Guarantee None TCP i Set the bandwidth limits for the QoS rule 1 2 3 Select Download or Upload for the QoS rule Enter the bandwidth limit Select whether the bandwidth is a Guarantee minimum or Max maximum Enter the IP address range to which the QoS rule will be applied Enter a starting IP address in the left field and the end IP address in the right field to define a range of IP addresses or enter an IP address in the left field only to define a single IP address Local Port Range Enter the port range to activate the QoS rule Enter a single port number e g 110 or a range of port numbers e g 110 120 Remote IP Address Enter the remote IP address range which will activate the QoS rule Enter a starting IP address in the left field and the end IP address in the ri
10. wireless and Ethernet access for your network devices WISP Mode The device connects wirelessly to your Wireless Internet Service Provider and provides 2 4GHz and or 5GHz Internet wireless and Ethernet access for your network devices 7 Follow the on screen instructions to complete setup Refer to the following chapters if you need help Wi Fi Access Point e EDIMAX Access Point Existing Wired Router xDSL Cable Modem Please connect one end of an Ethernet cable to your existing router and connect the other end to one of the ports 1 2 3 4 on the back of access point Other Modes EDIMAX Range Extender Wireless Bridge Wi Fi Router ETE You have selected Range Extender Mode The product connects wirelessly to your existing network and extends the wireless signal range Existing Router xDSL Cable Modem Il 1 Access Point Mode 1 Click YES NEED A Wi Fi ACCESS POINT button Access Point The default mode of this product is Wi Fi access point mode It connects to your router via Ethernet cable and provides Internet access for your computers smartphones tablets and any other network devices CHANGE TO A DIFFERENT MODE YES NEED A Wi Fi ACCESS POINT 2 Connect the yellow LAN port of your EW 7208APC to the LAN port of your existing router using an Ethernet cable then click Next Access Point Existing Wired Router xDSL Cable Modem Please connect one e
11. 2 minutes Configure via Client Enter the wireless client s PIN code here and PIN Code click Start PIN to activate PIN code WPS Refer to your wireless client s documentation if you are unsure of its PIN code I11 4 5 4 Access Control Access Control is a security feature that can help to prevent unauthorized users from connecting to your wireless router This function allows you to define a list of network devices permitted to connect to the EW 7208APC Devices are each identified by their unique MAC address If a device which is not on the list of permitted MAC addresses attempts to connect to the EW 7208APC it will be denied To enable this function check the box labeled Enable Wireless Access Control Access Control Enable Wireless Access Control MAC Address Comment Add Select MAC Address Device Name IP Address Select aa bb cc dd ee ff OFFLINE OFFLINE Edimax Save Settings MAC address Select a PC name from the drop down list and click gt gt to add enter it into the blank field to the right Click Refresh in the drop down menu to refresh the list of available MAC addresses If the address you wish to add is not listed enter it manually Enter a MAC address of computer or network device manually without dashes or colons e g for MAC address aa bb cc dd ee ff enter aabbccddeeff Enter a comment for reference identification consisting of up to 16 alphanumerical
12. 4 m Click Save to save the log on your computer as txt file Click Clear to clear erase the existing log Click Refresh to refresh the log and update any activity lll 4 9 8 Active DHCP Client Information about active DHCP clients is shown in the table which displays the DHCP server assigned IP address MAC address and time expired for each computer or device on the local network Active DHCP Client Time Expired Se 192 168 7 101 00 1b 63 cb 4c b5 forever I11 4 9 9 Statistics Displays sent and received packet network statistics Statistics Sent Packets 1745 2 4GHz Wireless Received Packets 30311 Sent Packets 517 5GHz Wireless Received Packets 56878 Sent Packets 1494 Ethernet LAN Received Packets 1868 Sent Packets 1624 Ethernet WAN Received Packets 5075 IV Appendix IV 1 Configuring your IP address For first time access to the URL http edimax setup please ensure your computer is set to use a dynamic IP address This means your computer can obtain an IP address automatically from a DHCP server You can check if your computer is set to use a dynamic IP address by following IV 1 1 How to check that your computer uses a dynamic IP address Static IP users can also temporarily modify your computer s IP address to be in the same IP address subnet e g 192 168 2 x x 2 3 254 as the EW 7208APC in order to access http edimax setup A The EW 7208APC s default IP address
13. 4GHz or 5GHz Wireless Bridge Please select the wireless frequency that same as your existing wireless network 1 Enable 5GHz 2 Enable 2 4GHz 4 Select the Wi Fi network name SSID which you wish to connect to and click Next to continue A If the Wi Fi network you wish to connect to does not appear try clicking Refresh Wireless Bridge 5GHz Wireless Site Survey The wireless bridge is surveying all available routers nearby Please select the router you wish to connect to If the router you wish to connect is not listed try clicking Refresh To connect to a hidden SSID please select Setup wireless bridge manually C Setup wireless bridge manually Ty 6208ac_5G 100 P CAP1200 ac 100 OBM Dlink817_5G 100 MIS Jacky_5G 98 EdimaxHQ 5G 92 Refresh To connect to a hidden SSID check the Setup wireless bridge A manually box and enter the details manually on the next page as shown below Wireless Bridge 5GHz Wireless Site Survey Please enter your existing Wi Fi network name SSID and security key if required Wi Fi network name SSID Encryption WPA2 Y Security Type TKIP AES Key Format Passphrase Wi Fi password Security Key E D Enter your existing wireless network s security key password in the Security Key field and click Next to continue Wireless Bridge 5GHz Wireless Site Survey Please ent
14. Connection specific DNS Suffix unnel adapter Teredo Tunneling Pseudo Interface Connection specific DNS Suffix Fub Address i l1 l1 I l1 Link local IPv6 Address fe8B 28 f6 2M4c 3 57 f38c 16 2661 0 9d38 953c 28f6 25B4c 3f57 f38c Default Gateway Users Win8 gt IV 1 4 3 Mac 1 Launch System Preferences and click on Network 2 If you are using an Ethernet cable to connect to your network your router s IP address will be displayed next to Router Metwor gt Show All Location Automatic Status FireWire Wi Fi gt e Configure IPv4 IP Address e ress er D USB Ne terface tu Mot Connected Aor Subnet Ma DNS Server Router k Connected Ethernet is currently active and has the IP address 192 168 10 179 Manually 1192 168 9 20 192 168 10 254 56 1 12 192 168 1 2 Search Domains 1 id Click the lock to prevent further changes 3 If you are using Wi Fi click Wi Fi in in the bottom right corner Advanced Assist me Revert Apply the left panel and then Advanced eoo Network lt gt Show All Location Automatic Status Connected Turn Wi Fi Off Wi Fi is connected to EdimaxHQ and has the Ethernet IP address 10 0 20 97 Mot Connected e FireWire Network Name EdimaxHQ Mot Connected USB Ne terface Y Automatically jo
15. Discovery Description TCP IP version 6 The latest version of the intemet protocol that provides communication across diverse interconnected 6 Select Obtain an IP address automatically and Obtain DNS server address automatically should be selected Internet Protocol Version 4 TCP 1Pv4 Properties You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings j Obtain an IP address automatically A 1 j Ce SALES A S49 ora IP address 192 168 2 10 Subnet mask 255 255 255 0 Default gateway Obtain DNS server address automatically aa Baez HE gt Pmt Preferred DNS server Alternate DNS server Pl Validate settings upon exit IV 1 1 4 Windows 8 1 From the Windows 8 Start screen you need to switch to desktop mode Move your curser to the bottom left of the screen and click FAE PC d ESPN Bret Bielema takes Arkansas job MET FA et a A E Mars redux NASA to launch another rover 2 In desktop mode click the File Explorer icon in the bottom left of the screen as shown below 3 Right click Network and then select Properties Network Y 7 E gt Network View Network discovery and file sharing are turned off Network computers and devices are not visible Click to change 4 Favorites BE Desktop Downloads S Recent p
16. Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 2 5cm 1 inch during normal operation Federal Communications Commission FCC RF Exposure Requirements This EUT is compliance with SAR for general population uncontrolled exposure limits in ANSI IEEE C95 1 1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C The equipment version marketed in US is restricted to usage of the channels 1 11 only R amp TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999 5 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity R amp TTE The R amp TTE Directive repeals and replaces in the directive 98 13 EEC Telecommunications Terminal Equipment and Satellite Earth Station Equipment As of April 8 2000 Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment All guidelines of this and of the computer manufacture must therefore be allowed at all times to ens
17. OBM Dlink817 2 4G 100 PP 6476ND 2 4G 100 MIS Jacky 100 9 A summary of your configuration will be displayed as shown below Check that all of the details are correct and then click Next to proceed A The device will use the same wireless password security key as the existing wireless network EDIMAX Range Extender Configuration is complete It is recommended that you backup your settings please click Backup this configuration to do so Then click Next when you are ready to continue IP address 192 168 2 103 2 4 GHz Wi Fi network name 6208ac 2 4G 2EX Wi Fi password abcd1234 IP address 192 168 2 102 5 GHz Wi Fi network name 6208ac 5G 2EX Wi Fi password abcd1234 Backup this configuration oe If you wish to backup the EW 7208APC s settings click Backup A this configuration to open a new window and save your current configuration to a txt file File Download E Do you want to open or save this file Mame range extender txt Type Text Document 251 bytes From edimax setup While files from the Intemet can be useful some files can potentially harm your computer If you do not trust the source do not open or save this file What s the risk Range Extender Applying your settings please wait 2396 g e P 11 A final congratulations screen will indicate that setup is complete You can now connect to the device s new SSID s which are shown on
18. SSIDs Multiple SSID Status CA O O O sso ATT Encryption mac Address 1 edimax 1 O Disable 80 1F 02 ED F2 D2 2 edimax 2 o WPA2 AES 80 1F 02 ED F2 D3 3 VLAN 1 WPA2 AES BO 1F 02 ED F2 D4 4 edimax 4 0 Disable 80 1F 02 ED F2 D5 Multiple SSID Basic Settings Multiple SSID Wireless Network Name SSID Band Channel Number VLAN ID 1 I MAC Address 80 1F 02 ED F2 D2 edimax 1 Enable Multiple SSID E Enable Wireless Clients Isolation 2 4 GHz b 8 n Auto Same as main SSID 0 Untagged 0 Tagged 1 4094 numbered 1 4 to configure Name SSID wireless network Enable Multiple Check uncheck this box to enable disable the SSID specified SSID Must be checked for the SSID to function Enable Wireless Check the box to enable wireless clients Clients Isolation isolation This prevents wireless clients connected to the EW 7208APC from communicating with each other and improves security Typically this function is useful for corporate environments or public hot spots EE usernames and passwords Displays the wireless standard used for the EW 7208APC s frequency band 2 4GHz b g n Allows 802 11b 802 11g and 802 11n wireless clients to connect to the EW 7208APC Channel Number Channel number for the guest network is the same as the main SSID and cannot be adjusted independently VLAN ID Set a VLAN ID for the specified SSID see below A AVLAN is a local area network which maps workstati
19. Search Network Network discovery and file sharina are turned off Network computers and devices are not visible Click to chanae AS Network and Sharing Center X Favorites BE Desktop de Downloads T del Network and Internet Network Connections gt vw Search Network Connections JO S Recent places Organize v Disable this network device Diagnose this connection Rename this connection i e oy Libraries ES Documents 2 Music f Pictures B Videos Diagnose Bridge Connections jE Computer Create Shortcut E Network Delete 1 item 1 item selected 12 3 2012 Network Network View ww Cu Network vC Search Network Network discovery and file sharina are turned off Network computers and devices are not visible Click to chanae r3 Network and Sharing Center H wr Favorites z BE Desktop p Network Connections de Downloads T us Network and Internet Network Connections Search Network Connections LP S Recent places Rename this connection y LH Libraries Es Documents Networking A Music fs Pictures E Videos Connect using EP Broadcom 440x 10 100 Integrated Controller 1 Computer This connection uses the following items de File and Printer Sharing for Microsoft Networks i Network CO 4 Microsoft Network Adapter Multiplexor Protocol 4 Microsoft LLDP Protocol Driver de Link Layer Topology Discovery Mapper 1 0 Driver Desc
20. Use the following IP address to specify a static IP address and then enter the details below A You can access the browser based configuration interface using the device s IP address instead of using the URL http edimax setup LAN IP Obtain an IP address automatically Use the following IP address IP Address 192 158 2 1 Subnet Mask 255 255 255 Default Gateway Address DNS Address Specify the IP address here This IP address will be assigned to the EW 7208APC and will replace the default IP address ae o 255 255 255 0 Address DNS Address Manually enter a DNS server IP address IP Address 111 3 4 2 4GHz Wireless 5GHz Wireless The 2 4GHz Wireless 5GHz Wireless menu allows you to configure SSIDs and security settings for your E access point WPS access control and scheduling SONS AL functions can also be managed from here WPS Access Control Schedule Y 2 4GHz Wireless v 5GHz Wireless Basic Multiple SSID WPS Access Control Schedule 111 3 4 1 Basic The Basic screen displays settings for your primary 2 4GHz or 5GHz Wi Fi network Basic Settings Disable Wireless Mode AP Band 2 4 GHz b g n Wireless Network Name 5510 edimax 2 1G 036150 Broadcast S5ID Enable Disable Enable Wireless Clients Isolation Channel Number Auto Y Site Survey Show list Wireless Clients Show list Disable Wireless Check the box to disable the wireless fu
21. aaa aaa aaa where each aaa can be anything from 000 to 255 or as four cascaded binary numbers separated by bbbbbbbb bbbbbbbb bbbbbbbb bbbbbbbb where each b can either be O or 1 A network mask is also a 32 bit binary pattern and consists of consecutive leading 1 s followed by consecutive trailing O s such as 11111111 11111111 11111111 00000000 Therefore sometimes a network mask can also be described simply as x number of leading 1 s When both are represented side by side in their binary forms all bits in the IP address that correspond to 1 s in the network mask become part of the IP network address and the remaining bits correspond to the host ID For example if the IP address for a device is in its binary form 11011001 10110000 10010000 00000111 and if its network mask is 11111111 11111111 11110000 00000000 It means the device s network address is 11011001 10110000 10010000 00000000 and its host ID is 00000000 00000000 00000000 00000111 This is a convenient and efficient method for access points to route IP packets to their destination ISP Gateway Address see ISP for definition The ISP Gateway Address is an IP address for the Internet access point located at the ISP s office ISP Internet Service Provider An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations LAN Local Area Network A LAN is a group of computers and devices connected toget
22. address field before you replace it Please make a note of this IP address subnet mask default gateway and DNS server addresses PY IP address 192 168 2 10 Subnet Mask 255 255 255 0 Preferred DNS Server 192 168 2 1 Click OK when finished IV 1 2 4 Windows 8 1 From the Windows 8 Start screen you need to switch to desktop mode Move your curser to the bottom left of the screen and click FAE PC a Rio de Janeiro Brazil SkyDrive ESPN Bret Bielema takes Arkansas job ai Sa TEE I Mars redux NASA to launch another rover 2 In desktop mode click the File Explorer icon in the bottom left of the screen as shown below OA 3 Right click Network and then select Properties Network View 7 Cu gt Network vi Search Network Network discovery and file sharing are turned off Network computers and devices are not visible Click to change 4 Ft Favorites This folder is empty BE Desktop de Downloads S Recent places 4 3 Libraries b E Documents gt g Music gt I Pictures gt BE Videos gt 1 Computer Open in new window Pin to Start Map network drive Disconnect network drive Delete 2 53 PM P B 0 ZR m 4 In the window that opens select Change adapter settings from the left side Library Tools Pictures Home Share View Manage Manage vi v Search Pictures 3 Favorites BE Desktop Jf Downloads T M Network a
23. against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC Caution This device and its antenna must not be co located or operating in conjunction with any other antenna or transmitter This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment Federal Communications Commission FCC Radiation
24. arranged into categories A Screenshots displayed are examples The information shown on your screen will vary depending on your configuration AMA AccessPoint NETWORKING PEOPLE TOGETHER Status Help LAN A O O Model Access Point IP Address 192 158 0 107 2 4GHz Wireless Current Time 2014 9 15 21 42 21 Subnet Mask 255 255 255 0 5GHz Wireless Hardware Version Rev A MAC Address 74 DA 38 0x 61 50 Firmware Version 1 01 Advanced Administration SGH Wireless Mode Access Point Mode Access Point 55 1D edimax_2 4G_036150 55 ID edimax 5G 036155 ChannelNumber 1 Channel Number 40 Security WPA2 AES Security WPAZ AES MAC Address 74 DA 38 03 61 50 MAC Address 74 DA 38 03 51 55 I11 3 2 Setup Wizard You can run the setup wizard again to reconfigure the Setup Wizard basic settings of the device or you can run a wizard to help you switch the device to a different operating mode Select Setup Wizard or Switch to Router Access Point Range Extender Wireless Bridge WISP mode and then click Run Wizard to begin Setup Wizard Setup Wizard This setup wizard is an intelligent and easy tool for you to complete the basic settings of the device quickly Switch to Router Access Point Range Extender Wireless Bridge WISP mode This setup wizard will guide you ta switch the device to another mode Setup Wizard This wizard will help you to set
25. can enjoy Wi Fi connectivity without accessing your primary network The Guest screen displays settings for your guest Wi Fi network A b N menu Guest Basic Settings Y Enable Guest SSID Guest Wireless Security The guest network is separate from your primary network The settings for your primary network can be found in the Basic Wireless Guest Name edimax 1 Enable Wireless Clients Isolation Band 2 4 GHz b g n Channel Number Auto Same as main SSID Encryption Disable guest Wi Fi network Name wireless network Enable Wireless Clients Isolation Channel Number Check the box to enable wireless clients isolation This prevents wireless clients connected to the EW 7208APC from communicating with each other and improves security Typically this function is useful for corporate environments or public hot spots and can prevent brute force attacks on clients usernames and passwords Displays the wireless standard used for the EW 7208APC s frequency band 2 4GHz B G N Allows 802 11b 802 11g and 802 11n wireless clients to connect to the EW 7208APC Channel number for the guest network is the same as the main SSID and cannot be adjusted independently WPA RADIUS encyrption type and 802 1x Authentication are not available for the guest network Il 4 5 3 WPS Wi Fi Protected Setup is a simple way to establish connections between WPS compatible devices WPS can be activated
26. here Enable Disable time to live TTL function which limits the lifespan of network data to improve performance Give this Internet service a name optional MTU Enter the maximum transmission unit MTU value of your network connection The default value is 1392 Connection Type Specify a connection type Continuous Connected all the time Connect on Demand Connect when you initiate an Internet connection Manual Connect disconnect manually using the Connect and Disconnect buttons Idle Time Out Specify the amount of time the router waits before shutting down an idle connection Only available when Connect on Demand above is selected Enable Dual WAN Enable disable dual WAN access When you Access enable dual WAN access select an IGMP source and enter a Host Name and MAC Address lll A 3 1 4 PPTP Select PPTP if your ISP is providing you Internet access via PPTP Point to Point Tunneling Protocol Then select Obtain an IP address automatically or Use the following IP address depending on your ISP PPTP amp Obtain an IP address automatically Host Name MAC Address Use the following IP address Static IP Address Subnet Mask Default Gateway Address MAC Address DNS Address DNS1 Address DNS Address DMS3 Address Enable Dual Wan Access IGMP Source PPTP Settings User ID Password PPTP Gateway Connection ID MTU BEZEQ ISRAEL Connection Type Idl
27. i ae Cu Network 1 item 1 item selected amp j 12 3 2012 Network Network View Cu gt Network Search Network Network discovery and file sharina are turned off Network computers and devices are not visible Click to chanae a u Network and Sharing Center us Network Connections YX Favorites BE Desktop Je Downloads T LE Network and Internet Network Connections Search Network Connections S Recent places Rename this connection z gt fi e Libraries ES Documents Networking 2 Music E Pictures B Videos Connect using Lu Broadcom 440x 10 100 Integrated Controller Computer This connection uses the following items dI File and Printer Sharing for Microsoft Networks i Network O 4 Microsoft Network Adapter Multiplexor Protocol amp Microsoft LLDP Protocol Driver amp Link Layer Topology Discovery Mapper 1 0 Driver de Link Layer Topology Discovery Responder Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks 1 item 1 item selected 2 55 PM P B 0 x m 553 2012 7 Select Use the following IP address and Use the following DNS server addresses then input the following values 4 h Your existing static IP address will be displayed in the IP address field before you replace it Please make a note of
28. m 45 SBEUID yd pes 8 o cen uisus Due dte se tU nM O 46 E AP 48 2 4GHZ Wireless S SGHZ WIFelesSs iia A A ii 49 Basi aeo ab itae du SM ea eect tes Bane tL tune cte to DUM te 50 Bicis mec en E re ue Ren ae 54 MEP A ELE eee UN alae eae 55 WEA Pre ohare d KEV assets A AA 56 WPA celftce T ea Ea E AN 57 MUA e ID E T 58 WIP O AA AS A A 60 ACCESS CONTO Mia tdi 62 o ieu oin ac DTI o Voi Se Gentle ui bu espe ai vas eaten eate ir edt TRE EON en 64 AAV geom rcu m n 66 LAGH WTO SS 66 DO ZVI OS EP o A abad aD zen Losada tate DOS Cos ds n a bL SER I 68 Administratio Masias 70 TIME ZONA ta pnemuaw cay T a Veseaniorennane cen 70 PASS WOL A cael dev ate E A 71 Backup Restore tds 72 111 3 6 4 OS FCC POPE PA Po In O ce miu Ee ISI ei I bic gm IE 72 IIl 3 6 5 A N N O E N E O OE NS OO 73 111 4 Main Menu Other MOOSS il ci 74 111 4 1 e rr E 75 111 4 2 SEU VIZ Oae a E ria 76 111 4 3 Interme E Pies 78 111 4 3 1 WAN Rojo 79 111 4 3 1 1 DINNER d um du 79 111 4 3 1 2 o A CE o Oo A 80 111 4 3 1 3 PROL M 82 111 4 3 1 4 PAT ad 84 111 4 3 1 5 TA H ater O 86 111 4 3 2 bib n sl 88 111 4 4 LAN ida 90 111 4 5 2 4GHz Wireless amp 5GHz Wireless iii ia 92 111 4 5 1 O 93 111 4 5 1 1 DIST A AA AAA A 97 111 4 5 1 2 WEB tia ia 98 111 4 5 1 3 WPA PresShared evo A ae 99 Ill 4 5 1 4 WPACRSOIUS cra edes ti situe Ne nr A Eu NP MEME NR p du I Nd EI EIE 100 1
29. open a new window and save your current configuration to a txt file File Download asia ES a Do you want to open or save this file Mame wireless bridge txt Type Text Document 255 bytes From edimax setup While files from the Intemet can be useful some files can potentially harm your computer If you do not trust the source do not open or save this file What s the risk O Please wait a moment until the EW 7208APC is ready Wireless Bridge Applying your settings please wait 1696 10 A final congratulations screen will indicate that setup is complete Please close the browser window YO MAX Wireless Bridge Congratulation You have sucessfully completed setup Please connect your wired devices to the ports 1 2 3 4 on the back of wireless bridge For advanced settings please access http edimax setup from your computer s web browser IP address 192 168 2 102 5 GHz Wi Fi network name 6208ac 5G Wi Fi password abcd1234 11 The EW 7208APC is working and ready for use You can now connect the EW 7208APC to your network device using an Ethernet cable and connect to your network as usual Il 4 Wi Fi Router Mode 1 Select Wi Fi Router from the top menu and click Next EDIMAX EXE You have selected Wi Fi Router Mode The product connects to your modem via Ethernet cable and provides Internet access for your computers smartphones tablets and any other network devices xD
30. password WPA2 AES abcd1234 x at least 8 characters E 6 A summary of your configuration will be displayed as shown below Check that all of the details are correct and then click Next to proceed EDIMAX Access Point Configuration is complete It is recommended that you backup your settings please click Backup this configuration to do so Then click Next when you are ready to continue 2 4 GHz Wi Fi network name edimax_2 4G_75EDFB Wi Fi password abcd1234 5 GHz Wi Fi network name edimax_5G_75EE00 Wi Fi password abcd1234 Backup this configuration If you wish to backup the device s settings click Backup this configuration to open a new window and save your current configuration to a txt file PY EE E Do you want to open or save this file Mame access point txt Type Text Document 148 bytes From edimax setup While files from the Intemet can be useful some files can potentially harm your computer If you do not trust the source do not open or save this file What s the risk 7 Please wait a moment until the EW 7208APC is ready Access Point Applying your settings please wait 2096 g 8 A final congratulations screen will indicate that setup is complete You can now connect to the device s new SSID s which are shown on the screen then close the browser window E EDIMAX Access Point Congratulation You have successfully com
31. shared Key Format Passphrase Pre shared Key ETE NCCHN Wireless Security Wireless Security Encryption WEP I Key Length 64 bit Key Format Hex 10 characters Encryption Key eee ee ee ee Hide Enable 802 1x Authentication Select an encryption type from the drop down menu A WPA Pre shared Key is the recommended and most secure encryption type Wireless Security Encryption Disable Fl Enable 802 1x Authentication WEP WPA Pre shared Key WPA RADIUS 111 3 4 1 1 Disable Encryption is disabled and no password key is required to connect to the EW 7208APC A Disabling wireless encryption is not recommended When s disabled anybody within range can connect to your device s SSID Enable 802 1x Check the box to enable the 802 1x Authentication authentication A RADIUS server is required to perform 802 1x authentication enter the RADIUS server s information in the relevant fields below V Enable 802 1x Authentication RADIUS Server IP address RADIUS Server Port 1812 RADIUS Server Password 111 3 4 1 2 WEP WEP Wired Equivalent Privacy is a basic encryption type For a higher level of security consider using WPA encryption Wireless Security Encryption WEP Key Length 64 bit Key Format Hex 10 characters e Encryption Key ssssscese 4 Hide Enable 602 1x Authentication Key Length Select 64 bit or 128 bit 128 bit is more secure than 64 bit Key F
32. the screen then close the browser window EU i MAX Range Extender Congratulation You have successfully completed setup Please connect to the device s new Wi Fi network name SSID listed below For advanced settings please access http edimax setup from your computer s web browser 2 4 GHz Wi Fi network name 6208ac 2 4G 2EX Wi Fi password abcd1234 5 GHz Wi Fi network name 6208ac 5G 2EX Wi Fi password abcd1234 12 The EW 7208APC is working and ready for use Refer to IV 2 Connecting to a Wi Fi network if you require more guidance Il 3 Wireless Bridge Mode 1 Select Wireless Bridge from the top menu and click Next EDIMAX ETE You have selected Wireless Bridge Mode The product connects to a network device via Ethernet cable and acts as a wireless receiver allowing the network device to join your Wi Fi network 2 Please ensure your EW 7208APC is within Wi Fi range of your existing wireless router Click Next to continue Wireless Bridge Existing Router xDSL Cable Modem This setup wizard will assist you to setup a wireless connection between the wireless bridge and your existing router Please ensure the wireless bridge is within the coverage range of your existing wireless network E 3 Select the frequency 2 4GHz or 5GHz of your existing wireless network A In wireless client mode the EW 7208APC can only connect to one wireless network frequency i e 2
33. the MAC address here If you are connecting the router to a computer press Clone Mac to automatically enter your computer s MAC address Static IP Address Input the IP address assigned by your ISP here Subnet Mask Input the subnet mask assigned by your ISP here Input the default gateway assigned by your ISP Address here Some ISPs may call this Default Route MAC Address If your ISP filters access by MAC addresses enter your computer s MAC address here Click Clone MAC to automatically enter your computer s MAC address DNS Address Select Obtain an IP address automatically or Use the following IP address Check with your ISP if you are unsure DNS Address 1 22 amp 3 Enter the DNS address es assigned by your ISP here Enable Dual WAN Enable disable dual WAN access When you enable Access dual WAN access select an IGMP source and enter a Host Name and MAC Address UserID Input the user name assigned by your ISP here Specify a reference name ID for the connection MTU Enter the maximum transmission unit MTU value of your network connection The default value is 1392 Connection Type Specify a connection type 1 Continuous Connected all the time 2 Connect on Demand Connect when you initiate an Internet connection 3 Manual Connect disconnect manually using the Connect and Disconnect buttons Idle Time Out Specify the amount of time th
34. to provide various internet services on different local computers via a single internet IP address Virtual Server E Enable Virtual Server Private IP Computer Name Private Port Public Port Select pe Both Current Virtual Server Table Computer Name Private IP Private Port Public Port Delete Salaria J Delet Al Save Settings Private IP Specify the IP address of the computer on your local network Computer Name Select the name of a Windows computer from the drop down menu and click to auto input its IP address in the Private IP field the computer in your local network on your local network identification Current Virtual Table entries will be displayed in the table shown below Current Virtual Server Table Computer Name Private IP Private Fort Public Port _ Delete Selected Delete All Delete Selected Delete selected or all entries from the table Delete All 111 4 8 4 2 4GHz Wireless These settings are for experienced users only Please do not change any of the values on this page unless you are already familiar with these functions 2 4GHz Wireless Wireless Module Fragment Threshold RTS Threshold Beacon Interval a JTIM Peri od Data Rate N Data Rate Channel Width Preamble Type CTS Protect Tx Power WMNM Enable 2346 256 2346 2347 0 2347 100 20 1024 ms 3 1 10 Auto I Auta Auto 20 40 MHZ 20 MHZ
35. up the basic functions and settings of the device For guidance about using the setup wizard please refer to Il Installation Switch to Router Access This wizard will help you to switch the device Point Range Extender to a different operating mode Wi Fi router Wireless Bridge WISP mode access point mode range extender mode wireless bridge or WISP mode see below Switch to Router Access Point Range Extender Wireless Bridge WISP mode Follow the on screen instructions to back up your current settings and then reset the device back to its factory default settings 2 After the device has reset you Will see the screen below Close your browser and open it again Reset to Default E You have successfully reset the device to factory defaults Please close the browser and open it again This device will start running the setup wizard for you to switch the mode 3 Follow the on screen wizard to setup your device in a different mode Refer to Il Installation Step 3 onwards for help if needed A If you don t see the Get Started screen try reconnecting to the gt edimax setup SSID and go to http edimax setup in a web browser 111 3 3 LAN You can configure your Local Area Network LAN on LAN this page and modify the IP address of the device The devices default IP address is 192 168 2 1 Select Obtain an IP address automatically for the device to automatically get an IP address from the router or
36. use the IP address 192 168 2 10 though you can use any IP address in the range 192 168 2 x x 2 3 254 in order to access iQ Setup browser based configuration interface A Please make a note of your static IP before you change it IV 1 2 1 Windows XP 1 Click the Start button it should be located in the lower left corner of your computer then click Control Panel Double click the Network and Internet Connections icon click Network Connections and then double click Local Area Connection The Local Area Connection Status window will then appear click Properties Local Area Connection Properties General Authentication Advanced Connect using BB AMD PCNET Family PCI Ethemet Ad This connection uses the following items Client for Microsoft Networks imi File and Printer Sharing for Microsoft Networks F d ce LIT IT Description Transmission Control Pratacol Intermet Protocol The default Wide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected Notify me when this connection has limited ar no connectivity 2 Select Use the following IP address and Use the following DNS server addresses then input the following values 4 h Your existing static IP address will be displayed in the IP gt address field before you replace it Please make a note of this IP address subnet m
37. your computer MAC Address For some applications you may need to designate a specific MAC address for the router Please enter the MAC address here If you are connecting the router to a computer press Clone Mac to automatically enter your computer s MAC address DNS Address Select Obtain an IP address automatically or Use the following IP address Check with your ISP if you are unsure ISP here MTU Enter the maximum transmission unit MTU value of your network connection The default value is 1500 Enable Disable time to live TTL function which limits the lifespan of network data to improve performance 111 4 3 1 2 Static IP Select Static IP if your ISP provides Internet access via a fixed IP address Your ISP will provide you with such information as IP address subnet mask gateway address and DNS address Static IP Fixed IP IP Address 172111 Subnet Mask 255 255 0 0 Default Gateway Address 172 1 1 254 MAC Address DNS1 Address 0 0 0 0 DN52 Address 0 0 0 0 DM53 Address 0 0 0 0 MTU 1500 512 MTU Value lt 1500 TTL 9 Disable Enable Save Settings Fixed IP Address Input the IP address assigned by your ISP here po Input the subnet mask assigned by your ISP here Default Gateway Input the default gateway assigned by your Address ISP here Some ISPs may call this Default Route MAC Address For some applications you may need to designate a specific MAC address for the router Plea
38. 11 4 5 2 CUE iio 101 111 4 5 3 WES as 103 111 4 5 4 ACCESS CONTO aetas chase cei eee bt eT rb DNE dei a 105 111 4 5 5 61 5 PPP Rem E M S des E MM ME eM 107 111 4 6 BAV lla a 109 111 4 6 1 UREBICIN Sas 109 111 4 6 2 ACCESS CONTO 111 111 4 6 3 Bi CCP 115 111 4 6 4 DOS A a NE 116 111 4 7 Le A HH w eee Tee 118 111 4 7 1 OOS 118 111 4 7 2 IUOS OOO 121 111 4 8 Advance A O II II 123 111 4 8 1 Stauc OUI MGV io aii 123 111 4 8 2 Port FO Wa AIN Es A A T eue OR E 125 111 4 8 3 AYA Wes Des IR I e rH 127 Ill 4 8 4 ZAG WIFeleSS s dieses ect tesa io 128 111 4 8 5 A A o MuR oS Co dE M SOR EUER 130 111 4 8 6 IGMP naaa 132 111 4 8 7 LIP Paca dente ut Edi ei M EE di dU EU M REM di dc UE 133 111 4 9 PA CUTAN TANS TACO ria 134 111 4 9 1 Me ZoNe rata iia 134 111 4 9 2 111 4 9 3 111 4 9 4 111 4 9 5 111 4 9 6 111 4 9 7 111 4 9 8 111 4 9 9 IV 1 IV 1 1 IV 1 1 1 IV 1 1 2 IV 1 1 3 IV 1 1 4 IV 1 1 5 IV 1 2 IV 1 2 1 IV 1 2 2 IV 1 2 3 IV 1 2 4 IV 1 2 5 IV 1 3 IV 1 3 1 IV 1 3 2 IV 1 4 IV 1 4 1 IV 1 4 2 IV 1 4 3 IV 2 IV 3 BETS o RR EE 135 Remote ACCESS mias 136 Backup RES TOL suco NOE MI M M LM D M M S 137 HUDSON E M ME MEN M ME M 137 RESTAT e 138 Fei ec 138 Ac
39. Address f Add MAC Filtering Table Computer Name Client PC MAC Address 1 MACBOOK 41729BA 00 1b 63 cb 4c b5 F Delete Selected Delete All Enable IP Filtering Table Deny Allow IF Filtering Table Client PC Client PC IP Description Address Client Service WWW E mail Sending News Forums E mail Receiving El 1 Laptop 132 168 2 101 Secure HTTP File Transfer Add PC Delete Selected Delete All Save Settings Settings have been saved Please click here to restart the router and bring the new settings into effect MAC Filtering Enable MAC Check the box to enable MAC filtering and Filtering select whether to Deny or Allow access for specified MAC address Client PC MAC Enter a MAC address of computer or network Address device manually without dashes or colons e g for MAC address aa bb cc dd ee ff enter aabbccddeeff Computer Name Select a computer name from the drop down list and click lt lt to add its MAC address into the Client PC Mac Address field Click Refresh in the drop down menu to refresh the list of available MAC addresses If the address you wish to add is not listed enter it manually Comment Enter a comment for reference identification consisting of up to 16 alphanumerical characters D E MAC address filtering table MAC address entries will be listed in the table as shown below Select
40. Dynamic IP 2 4 GHz Wi Fi network name edimax_2 4G_75EDFB Wi Fi password abcd1234 5 GHz Wi Fi network name edimax_5G_75EE00 Wi Fi password abcd1234 Backup this configuration If you wish to backup the device s settings click Backup this A configuration to open a new window and save your current configuration to a txt file File Download a qup a came am Do you want to open or save this file Mame wisp txt Type Text Document 141 bytes From edimax setup While files from the Intemet can be useful some files can potentially harm your computer f you do not trust the source do not open or save this file What s the risk 13 Please wait a moment until the EW 7208APC is ready Applying your settings please wait 1696 14 A final congratulations screen will indicate that setup is complete You can now connect to the device s new SSID s which are shown on the screen then close the browser window EDIMAX Congratulation You have successfully completed setup Please connect to the device s new Wi Fi network name SSID listed below For advanced settings please access http edimax setup from your computer s web browser 2 4 GHz Wi Fi network name edimax 2 4G 75EDFB Wi Fi password abcd1234 5 GHz Wi Fi network name edimax 5G 75EE00 Wi Fi password abcd1234 15 TheEW 7208APC is working and ready for use Refer to IV 2 Connecting to a Wi Fi network if you requir
41. EDIMAX NETWORKING PEOPLE TOGETHER EW 7208APC User Manual 09 2014 v1 0 Edimax Technology Co Ltd No 3 Wu Chuan 3rd Road Wu Gu New Taipei City 24891 Taiwan Email support edimax com tw Edimax Technology Europe B V Fijenhof 2 5652 AE Eindhoven The Netherlands Email support edimax nl Edimax Computer Company 3350 Scott Blvd Bldg 15 Santa Clara CA 95054 USA Live Tech Support 1 800 652 6776 Email support Qedimax com CONTENTS Product INTO MA CIO c oeovo eei c e eee vo ov oe Ce Cos 3e ani l 1 l 2 l 3 I A Package CODtellbS ii o idas 1 EDS TUS aaa 2 Back Panels iaa tdt ida 3 SAME ACNE UN o See 4 INSTAM CON rr Il 1 Il 2 Il 3 Il 4 Il 5 Il 6 Il 7 Access POINU MOOG m Anarin aE E ae 9 Rane Extender Mode a MEAM ME E UM UE 14 Wireless Bra ge IM Ode AA 21 WisFIROUEer MOGO it AAN 27 WISP MOJ Errietan T ds 32 WV SOU Scc dba ne tva ox atus E tem hcl temi amet 40 Reset to Factory Default SOULS uide ree e rr AAA vr e AS 40 Browser Based Configuration Interface cere eee 4 Ill 1 Ill 2 Ill 3 Ill 3 1 Ill 3 2 Ill 3 3 Ill 3 4 111 3 4 1 111 3 4 1 1 111 3 4 1 2 111 3 4 1 3 111 3 4 1 4 Ill 3 4 2 I11 3 4 3 Ill 3 4 4 Ill 3 4 5 Ill 3 5 Ill 3 5 1 Ill 3 5 2 Ill 3 6 Ill 3 6 1 Ill 3 6 2 Ill 3 6 3 LOB Meran T 41 SIVE SE UNES E 43 Man Menu Access Pot Mode ind V Ue axtui d tio oe ER UE 44 DUALS
42. Fi Multimedia technology can improve the performance of certain network applications such as audio video streaming network telephony VoIP and others When WMM is enabled the device will prioritize different kinds of data and give higher priority to applications which require instant responses for better performance 111 4 8 6 IGMP IGMP is a communications protocol used to establish multicast group memberships It allows for a more efficient use of resources and better performance for applications such as IPTV video streaming IGMP IGMP Snooping Enable Disable IGMP Proxy Enable Disable Save Settings IGMP Snooping IGMP snooping monitors traffic between hosts and multicast routers to facilitate bandwidth conservation Select enable or disable IGMP Proxy IGMP proxy enables intelligent multicast forwarding based on IGMP snooping information Select enable or disable A It is recommended to set IGMP Snooping and IGMP Proxy to amp Enable 111 4 8 7 UPnP Universal plug and play UPnP is a set of networking protocols which enables network devices to communicate and automatically establish working configurations with each other Select Enable or Disable UPnP UPnP Feature W Enable Y Disable Save Settings Ill 4 9 Administration Various administrative functions can be accessed from v Administration y 2 EM the Administration menu Time Zone Password Remote Access Back
43. IP addresses to specified network devices identified by their unique MAC address Static DHCP Lease Table Only 16 sets of addresses are allowed 1 00 1b 63 cb 4c b5 192 168 7 110 E Delete Selected Delete All Enable Static DHCP Leases MAC Address IP Address Enable Static DHCP Enable disable static DHCP leases This must Leases be enabled in order to assign any network device a static IP address address here network device here Add the information to the Static DHCP Leases Table Clear the MAC address and IP address fields Delete Selected Delete selected or all entries from the table Delete All 111 4 5 2 4GHz Wireless amp 5GHz Wireless 2 AGHZ ass The 2 4GHz Wireless amp 5GHz Wireless menu allows eS you to configure SSID and security settings for your Wi Fi network along with a guest Wi Fi network WPS access control and scheduling functions can also be managed from here Basic Guest WPS Access Control schedule 5GHz Wireless Basic Guest WPS Access Control ochedule A The Schedule function is not available in WISP mode for the wireless band that is used to connect to WISP s AP lll A 5 1 Basic The Basic screen displays settings for your primary 2 4GHz or 5GHz Wi Fi network Basic Settings C Disable Wireless Band 2 4 GHz b g n Wireless Network Name SSID J208APC 2 4G Broadcast SSID 8 Enable Disable C Enable Wireless Client
44. Intermet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected Notify me when this connection has limited or no connectivity 2 Obtain an IP address automatically and Obtain DNS server address automatically should be selected Internet Protocol TCP IP Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Othenvise vau need to ask pour network administrator For the appropriate IP settings Obtain an IP address automatically BE m BEEN IV 1 1 2 Windows Vista 1 Click the Start button it should be located in the lower left corner of your computer then click Control Panel Click View Network Status and Tasks then click Manage Network Connections Right click Local Area Network then select Properties The Local Area Connection Properties window will then appear select Internet Protocol Version 4 TCP IPv4 and then click Properties al Area Connection Properties Networking Connect using a Intel R PRO 1000 MT Network Connection This connection uses the following items 9 Client for Microsoft Networks vl dillQoS Packet Scheduler iv dil File and Printer Sharing for Microsoft Networks
45. LED Status EW 7208APC is on A EW 7208APC is off Internet connection is ready Internet Factory default state or Ethernet Flashing cable not connected or no Internet connection o tem Wi Fi wireless activity 2 4GHz Wi Fi on AGH WIFI wireless data Blue fnnt 2 4GHz WPS is active Off 2 4GHz Wi Fi not active EE Wi Fi wireless activity GHz Wi Fi MEET data GS Flashing 5GHz WPS is active eme 5GHz Wi Fi not active l 3 Back Panel 5GHz Antenna 2 4GHz Antenna 2 4GHz Antenna Reset WPS Button Internet Wireless Radio Power Port ON OFF Switch LAN Ports 1 4 Internet WAN Port Il 4 Safety Information In order to ensure the safe operation of the device and its users please read and act in accordance with the following safety instructions 1 2 The device is designed for indoor use only do not place it outdoors Do not place the device in or near hot humid places such as a kitchen or bathroom Do not pull any connected cable with force carefully disconnect it from the EW 7208APC Handle the device with care Accidental damage will void the warranty of the device The device contains small parts which are a danger to small children under 3 years old Please keep the device out of reach of children Do not place the device on paper cloth or other flammable materials The device may become hot during use There are no user serviceable pa
46. Mozilla Firefox gr E mail AlanChiu Microsoft Office Outlook i Documents e Internet Explorer Pictures 3 Type the name of a program folder document or Internet resource and Windows will open it for you Qe XnView Music Oper cmd gt Recent Items e This task will be created with administrative privileges e Google Chrome Computer CREE Y Ec Microsoft Office PowerPoint 2007 C ox J Network TEN ES Microsoft Office Word 2007 Adobe Reader 9 Connect To a pin Command Prompt Control Panel es BBEK Microsoft Office xt Default Programs 6a Audacity gt All Programs 2 Anew window will open type ipconfig and press Enter Em Administrator CXWindows system321cmd exe Microsoft Windows CUersion 6 0 68082 Copyright amp c 2666 Microsoft Corporation fill rights reserved Co Wsers AlanCh7Za gt ipconf ig Ethernet adapter REGA Connection specific DNS Link local IPv6 Address IPu4 Address ene Mash zem ie Default Gateway gt fet 4cdc 3e7B ba56 1722 9 192 168 1H 14 255 255 255 H fp Rr rSadh e9c2 e57hz9 192 168 186 254 Wireless LAN adapter ee Sc P sm ee Media State n Media disconnected Connection specific DNS Suffix edimax com Tunnel adapter ism i b Media State we Hedia disconnected Connection specific DNS Suffix Tunnel adapter IE Fay Se n fa Media State Media disconnected Co
47. OCHOBHbIM Tpe60BaHMsaM M NONOKeHNAM lmpeKTUBbI 1999 5 EC 2009 125 EC Ez a berendez s megfelel az alapvet k vetelm nyeknek s m s vonatkoz ir nyelveknek 1999 5 EK 2009 125 EC Bu cihaz 1999 5 EC 2009 125 EC direktifleri zorunlu istekler ve diger h k mlerle ile uyumludur O6naaHaHHRA BinnoBinae BHMOraM i yMoBaM ANpekTuBN 1999 5 EC 2009 125 EC Toto zariadenie spi a z kladn po iadavky a al ie pr slu n ustanovenia smern c 1999 5 ES 2009 125 ES Dieses Ger t erf llt die Voraussetzungen gem den Richtlinien 1999 5 EC 2009 125 EC El presente equipo cumple los requisitos esenciales de la Directiva 1999 5 EC 2009 125 EC Questo apparecchio conforme ai requisiti essenziali e alle altre disposizioni applicabili della Direttiva 1999 5 CE 2009 125 CE Dit apparaat voldoet aan de essenti le eisen en andere van toepassing zijnde bepalingen van richtlijn 1999 5 EC 2009 125 EC Este equipamento cumpre os requesitos ess nciais da Directiva 1999 5 EC 2009 125 EC Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv 1999 5 EC 2009 125 EC Denna utrustning ar i verensst mmelse med de v sentliga kraven och vriga relevanta bestammelser i direktiv 1999 5 EG 2009 125 EG Dette udstyr er i overensstemmelse med de vaesentligste krav og andre relevante forordninger i direktiv 1999 5 EC 2009 125 EC Tama laite t ytt direktiivien 1999 5 EY 2009 125 EY oleelliset vaatimuks
48. PA2 AES abcd12 34 x at least 8 characters E J summary of your configuration will be displayed as shown below Check that all of the details are correct and then click Next to proceed oo EDIMAX Wi Fi Router Configuration is complete It is recommended that you backup your settings please click Backup this configuration to do so Then click Next when you are ready to continue Internet Type Dynamic IP 2 4 GHz Wi Fi network name edimax 2 4G 75EDFB Wi Fi password abcd1234 5 GHz Wi Fi network name edimax 5G 75EE00 Wi Fi password abcd1234 Backup this configuration E c If you wish to backup the device s settings click Backup this A configuration to open a new window and save your current configuration to a txt file File Download Do you want to open or save this file Mame router txt Type Text Document 149 bytes From edimax setup While files from the Intemet can be useful some files can potentially harm your computer f you do not trust the source do not open or save this file What s the risk 8 Please wait while the EW 7208APC applies your settings Wi Fi Router Applying your settings please wait 2196 O A final congratulations screen will indicate that setup is complete You can now connect to the device s new SSID s which are shown on the screen then close the browser window d EDIMAX Wi Fi Router Congratulation You have suc
49. Panel Devices and Printers Default Programs Help and Support Shut down aie View by Category Y User Accounts and Family Safety ay Add or remove user accounts iy Set up parental controls for any user Appearance and Personalization Change the theme Change desktop background Adjust screen resolution Clock Language and Region Change keyboards or other input methods Change display language Ease of Access Let Windows suggest settings Optimize visual display View your basic network information and set up connections A x C P See full map TS5 WIN7 Home network Internet This computer View your active networks Connect or disconnect Access type Mo Internet access Home network HomeGroup seem Home network 4 Click Properties General IP 4 Connectivity No Internet access IPy6 Connectivity No network access Media State Enabled Duration 02 08 52 Speed 100 0 Mbps Details Sent A Received Ow 951 332 4 398 184 Properties 5 Select Internet Protocol Version 4 TCP IPv4 and then click Properties Local Area Connection Pro Connect using amp Broadcom 44 x 10 100 Integrated Controller This connection uses the following items 1E Client for Microsoft Networks dallaoS Packet Scheduler File and Printer Sharing for Microsoft Networks amp ntemet Protocol Version 4 TCP LAT IP LO KE p mj pL r wi Link Layer Topology
50. SID for the range extender if you wish and set the security key for your existing wireless network if required Device SSID 6208ac 5G 2EX Security Key Em 6 Wait a moment while the EW 7208APC tests the wireless connection Range Extender Testing wireless connection 4096 7 Select Obtain an IP address automatically or Use the following IP address for your EW 7208APC If you are using a static IP enter the IP address subnet mask and default gateway Click Next to proceed to the next step a Obtain an IP address automatically is the recommended setting A for most users The IP address will be displayed in brackets Range Extender Connection test complete Please click Next when you are ready to continue Obtain an IP address automatically IP 192 168 2 102 D Use the following IP address IP address 192 Subnet Mask Default gateway 0 DNS 0 8 If you selected to use both 2 4GHz and 5GHz wireless frequencies in step 3 then repeat steps 4 7 for the 2 4GHz wireless frequency ED z MAX Range Extender 2 4GHz Wireless Site Survey The range extender is surveying all available routers nearby Please select the router you wish to connect to If the router you wish to connect is not listed try clicking Refresh To connect to a hidden SSID please select Setup extender manually Setup extender manually 6208ac 2 4G 10096 Dlink817 2 4G 2EX 10096
51. SL Cable Modem 2 Select whether to use the iQ Setup wizard recommended to detect your Internet connection type or enter the settings manually A Manual configuration is only recommended for advanced users EDIMAX Wi Fi Router The iQ Setup wizard can help detect your Internet connection type and walk you through setup step by step or you can setup your device manually e 1 iQ Setup wizard 2 Configure manually 3 Connect the blue Internet port of your EW 7208APC to the LAN port of your modem using an Ethernet cable and then click Next Wi Fi Router xDSL Cable Modem Please connect one end of an Ethernet cable to your modem and connect the other end to the Internet port on the router 4 Please wait a moment while the EW 7208APC tests the connection Wi Fi Router Connecting to Internet 2896 239 UE YN ND F Sj av 5 Click Next to continue and configure the device s wireless network Wi Fi Router Internet is now connected Please click Next to configure your wireless network 6 Enter a name and password for your 2 4GHz amp 5GHz wireless networks then click Next to continue Wi Fi Router Please set your Wi Fi network name SSID and Wi Fi password Wi Fi network name 2 4GHz edimax 2 4G 75EDFB Wi Fi password WPA2 AES abcd1234 at least 8 characters Wi Fi network name 5GHz ledimax 5G 7S5EEO0 Wi Fi password W
52. ally e 1 iQ Setup wizard 2 Configure manually 4 Select the wireless frequency 2 4GHz or 5GHz of your WISP network EDIMAX Please select the wireless frequency that same as your WISP used 1 Enable 5GHz 2 Enable 2 4GHz 5 Select the WISP SSID which you wish to connect to and click Next to continue A If the Wi Fi network you wish to connect to does not appear try clicking Refresh 2 4GHz Wireless Site Survey The Wi Fi router is surveying all available WISP nearby Please select the WISP you wish to connect to If the WISP you wish to connect is not listed try clicking Refresh To connect to a hidden SSID please select Setup WISP manually L Setup WISP manually Free Wi Fi 100 Dlink817 2 4G 2EX 100 PP 6476ND 2 4G 100 edimax_2 4G_939100 100 MIS Jacky 100 To connect to a hidden SSID check the Setup WISP manually A box and enter the details manually on the next page as shown below 2 4GHz Wireless Site Survey Please enther your WISP s Wi Fi network name and the security key provide from your WISP if required Wi Fi network name SSID Encryption Security Type 9 AES Key Format Passphrase Wi Fi password Security Key E 6 Enter your existing wireless network s security key password in the Security Key field and click Next to continue 2 4GHz Wireless Site Survey Please enter the security key provid
53. an entry using the Select checkbox MAC Filtering Table Computer Name Client PC MAC Address Select 1 MACBOOK 4 29BA 00 1b 63 cb 4c b5 E Delete Selected Delete All Delete Selected Delete selected or all entries from the table Delete All IP Filtering Enable IP Filtering Check the box to enable IP filtering and select whether to Deny or Allow access for specified IP address Opens a new window to add a new IP to the list to deny or allow access services according to above Access Control Add PC This page allows users to define service limitations of client PCs including IP address and service type Access Control Add PC Client PC Description Laptop Client PC IP address 192 168 2 101 Client PC Service Service Name Detail Description WWW HTTP TCP Port 80 3128 8000 8080 8081 E mail Sending SMTP TCP Port 25 News Forums NNTP TCP Port 119 E mail Receiving POPS TCP Port 110 Secure HTTP HTTPS TCP Port 443 File Transfer FTP TCP Port 21 20 MSN Messenger TCP Port 1863 7 Telnet Service TCP Port 23 E AIM AOL Instant Messenger TCP Port 5190 a NetMeeting H 323 TCP Port 389 522 1503 1720 1731 FE DNS UDP Port 53 7 SNMP UDP Port 161 162 a VPN PPTP TCP Port 1723 FE VPN L2TP UDP Port 1701 FE TCP All TCP Port IF UDP All UDP Port E User Define Service Protocol Both I Port Range Description of up to 16 alphanumeric characters Client PC IP addre
54. ask default gateway and DNS server addresses IP address 192 168 2 10 Subnet Mask 255 255 255 0 Preferred DNS Server 192 168 2 1 Click OK when finished IV 1 2 2 Windows Vista Click the Start button it should be located in the lower left corner of your computer then click Control Panel Click View Network Status and Tasks then click Manage Network Connections Right click Local Area Network then select Properties The Local Area Connection Properties window will then appear select Internet Protocol Version 4 TCP IPv4 and then click Properties 2 Local Area Connection Properties Networking Connect using a Intel R PRO 1000 MT Network Connection This connection uses the following items w 0 Client for Microsoft Networks v E QoS Packet Scheduler iv i File and Printer Sharing for Microsoft Networks 4 Intemet Protocol Version 4 TCP 1Pv4 1 a IN Ur alalallalal sai JULDC Link Layer Topology Discovery Responder paa Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks 2 Select Use the following IP address and Use the following DNS server addresses then input the following values Your existing static IP address will be displayed in the IP address A field before you replace it Please make a note of this IP address
55. bers e g 255 255 255 0 configured like an IP address It is used to create IP address numbers used only within a particular network as opposed to valid IP address numbers recognized by the Internet which must be assigned by InterNIC TCP IP UDP Transmission Control Protocol Internet Protocol TCP IP and User Datagram Protocol UDP TCP IP is the standard protocol for data transmission over the Internet Both TCP and UDP are transport layer protocol TCP performs proper error detection and error recovery and thus is reliable UDP on the other hand is not reliable They both run on top of the IP Internet Protocol a network layer protocol WAN Wide Area Network A network that connects computers located in geographically separate areas e g different buildings cities countries The Internet is a wide area network Web based management Graphical User Interface GUI Many devices support a graphical user interface that is based on the web browser This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control configure or monitor the device being managed 2 DI NETWORKING PEOPLE TOGETHER COPYRIGHT Copyright Edimax Technology Co Ltd all rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical ma
56. cessfully completed setup Please connect to the device s new Wi Fi network name SSID listed below For advanced settings please access http edimax setup from your computer s web browser 2 4 GHz Wi Fi network name edimax 2 4G 75EDFB Wi Fi password abcd1234 5 GHz Wi Fi network name edimax 5G 75EE00 Wi Fi password abcd1234 10 The EW 7208APC is working and ready for use Refer to IV 2 Connecting to a Wi Fi network if you require more guidance Il 5 WISP Mode 1 Select WISP from the top menu and click Next EDIMAX VEZ AO AAA You have selected WISP Mode The product connects wirelessly to your Wireless Internet Service Provider and provides Internet access for your cpmputers smatphones tablets and network devices hd ug Wireless Internet or Hotspot AP m m 2 Please ensure your EW 7208APC is within Wi Fi range of your WISP network and click Next to continue Wireless Internet Service Provider Cx Hotspot AP This setup wizard will assist you to setup a wireless connection between your Wi Fi router and WISP E Bf 3 Select whether to use the iQ Setup wizard recommended to detect your Internet connection type or enter the settings manually A Manual configuration is only recommended for advanced users EDIMAX The Q Setup wizard can help detect your Internet connection type and walk you through setup step by step or you can setup your device manu
57. characters Add Click Add to add the MAC address to the MAC address filtering table MAC address entries will be listed in the table as shown below Select an entry using the Select checkbox 00 1b 63 cb 4c b5 MACBOOK 4 29BA 192 168 2 101 Ia Delete Selected Delete All Delete Selected Delete selected or all entries from the table Delete All II1 4 5 5 Schedule The schedule feature allows you to automate the wireless radio to switch on off at specified times Multiple schedules can be configured Check uncheck the box Enable Schedule Settings to enable disable the wireless on off scheduling function A This function is not available in WISP mode for the wireless band A that is used to connect to WISP s AP A The EW 7208APC must remain connected to the Internet and use an NTP server for the schedule feature to function correctly Wireless Schedule Enable Schedule Settings 1 Weekdav Fl su nday El Monday Tuesday E Wednesday Weekday i L Thursday E Friday Fl satu rday 2 Time Hour O Minute 00 i 3 Command Wireless On I Monday Tuesday Wednesday Thursday Friday 01 00 wireless off P Monday Tuesday Wednesday Thursday Friday 08 00 wireless on E Delete Selected Delete All Save Settings Settings have been saved Please click here to restart the router and bring the new settings into effect Wireless scheduling can save energy and increase the security of your network
58. d passwords Select a wireless radio channel or use the default Auto setting from the drop down menu Click Show List to display a new window showing information about the surrounding wireless environment This information is useful to select an effective wireless channel number Click Show List to display a new window showing information about wireless clients Please disable any pop up blockers if you have difficulty using this function AP Bridge WDS Mode AP Bridge WDS m AP AP Bridge WDS Band Wireless Distribution System WDS can bridge repeat access points together in an extended network WDS settings can be configured as shown below 7 N When using WDS configure the IP address of each access point to be in the same subnet and ensure there is only one active DHCP server among connected access points preferably on the WAN side WDS must be configured on each access point using correct MAC addresses All access points should use the same wireless channel i MAC Address MAC Address 2 MAC Address 4 Set Security Set Security MAC Address 1 4 Enter the correct MAC address for other access points in WDS mode Set Security Click Set Security to open a new window and enter the security settings for WDS shown below Click Save when finished A Please ensure you setup and save wireless security settings before EE you click Set Security to set WDS security settings
59. ddress Specify the IP address which is allowed remote access Specify a port number 0 65535 used for remote access Ill 4 9 4 Backup Restore Backup Restore Backup Settings Browse ETZEN Restore Settings Restore to Factory Default Reset Backup Settings Click Save to save the current settings on your computer as config bin file Restore Settings Click Browse to find a previously saved config bin file and then click Upload to replace your current settings Restore to Click Reset to restore settings to the factory Factory Default default A pop up window will appear and ask you to confirm and enter your log in details Enter your username and password and click Ok See below for more information Ill 4 9 5 Upgrade The upgrade page allows you to upgrade the system firmware to a more recent version You can download the latest firmware from the Edimax website After the upgrade the system will restart A Do not switch off or disconnect the device during a firmware 2 upgrade as this could damage the device It is recommended that you use a wired Ethernet connection for a firmware upgrade Upgrade Browse lll A 9 6 Restart In the event that the router malfunctions or is not responding then it is recommended that you restart the device Restart In the event that the system stops responding correctly or stops functioning you can perform a system restart Your setting
60. dress to the same port of a local IP address The port number s of the Internet IP address and local IP address must be the same If the port number of the Internet IP address and local IP address is different please use the Virtual Server function instead Port Forwarding 7 Enable Port Forwarding Private IP Computer Name Port Range ES select url Both E Current Port Forwarding Table E ES rd ed yes esr zs inl Save Settings Private IP Enter the IP address of the computer on the local network Computer Name Windows computers on the local network will be listed here select a computer from the list and click to automatically add the IP address to the Private IP field Type Select the type of connection TCP UDP or Both Port Range Input the starting port number in the left field and input the ending port number in the right field If you only want to redirect a single port number only enter a port number in the left field Comment Enter a comment for reference or identification Port Forwarding Table entries will be displayed in the table shown below Current Port Forwarding Table Delete Selected Delete selected or all entries from the table Delete All lll A 8 3 Virtual Server This function allows you to set up an internet service on a local computer without exposing the local computer to the internet You can also build various sets of port redirection
61. e Time Out 000000000000 Clone MAC 0 0 0 0 0 0 0 0 0 0 0 0 8 Obtain an IP address automatically Use the following IP address 000000000000 0 0 0 0 0 0 0 0 0 0 0 0 Sera ppp fo ita 512 lt MTU Value 1492 LJ Enable for use with BEZEQ network in Israel only times Vi NNNM RENE 10 1 1000 minutes Enter the host name of your computer here If required MAC Address For some applications you may need to designate a specific MAC address for the router Please enter the MAC address here If you are connecting the router to a computer press Clone Mac to automatically enter your computer s MAC address Static IP Address Input the IP address assigned by your ISP here Subnet Mask Input the subnet mask assigned by your ISP here Default Gateway Input the default gateway assigned by your ISP Address here Some ISPs may call this Default Route MAC Address If your ISP filters access by MAC addresses enter your computer s MAC address here Click Clone MAC to automatically enter your computer s MAC address DNS Address Select Obtain an IP address automatically or Use the following IP address Check with your ISP if you are unsure here Enable Dual WAN Enable disable dual WAN access When you enable Access dual WAN access select an IGMP source and enter a Host Name and MAC Address IMTU Enter the maximum transmission unit MTU value of your network connection The default val
62. e from your WISP if required Device SSID Free Wi Fi Security Key J Wait a moment while the EW 7208APC tests the wireless connection Testing wireless connection 5696 8 Click Next to continue your Internet service type configuration Wireless connection succeeded Please click Next to completed your Internet service type configuration O wait a moment while the EW 7208APC connects to the Internet Connecting to Internet 3396 10 When the Internet is connected click Next to configure your wireless network Internet is now connected Please click Next to configure your wireless network 11 Entera name and password for your 2 4GHz amp 5GHz wireless networks then click Next to continue EDIMAX Please set your Wi Fi network name SSID and Wi Fi password Wi Fi network name 2 4GHz edimax 2 4G 75EDFB Wi Fi password WPA2 AES abcd1234 at least 8 characters Wi Fi network name 5GHz edimax 5G 75EEO00 Wi Fi password WPA2 AES abcd1234 at least 8 characters E 12 A summary of your configuration will be displayed as shown below Check that all of the details are correct and then click Next to proceed EDIMAX Configuration is complete It is recommended that you backup your settings please click Backup this configuration to do so Then click Next when you are ready to continue Internet Type
63. e more guidance Il 6 WPS Setup If your wireless device supports WPS Wi Fi Protected Setup then you can use this method to connect to the EW 208APC s Wi Fi network 1 Press the WPS button on the EW 7208APC for 2 5 seconds to activate WPS The WLAN LED will be lighted on to indicate that WPS is active 2 Within two minutes press the WPS button on the wireless device client to activate its WPS 3 The devices will establish a connection Repeat for additional wireless devices A Please check the instructions for your wireless device for how long you need to hold down its WPS button to activate WPS Il 7 Reset to Factory Default Settings If you experience problems with your EW 7208APC you can reset the device back to its factory settings This resets all settings back to default 1 Press and hold the WPS Reset button found on the back panel for at least 10 seconds until the power LED begins to flash 2 Release the button when the power LED is flashing 3 Wait for the EW 7208APC to restart The EW 7208APC is ready for setup when the power LED 2 4GHz Wi Fi and 5GHz Wi Fi LEDs display on Ill Browser Based Configuration Interface After you have setup the EW 7208APC as detailed in Il Installation or the included Quick Installation Guide you can use the browser based configuration interface to configure advanced settings A Please ensure that your computer is set to use a dynamic IP gt address R
64. e router waits before shutting down an idle connection Only available when Connect on Demand above is selected 111 4 3 2 DDNS Dynamic DNS DDNS is a service which provides a hostname to IP service for dynamic IP users The changing nature of dynamic IPs means that it can be difficult to access a service provided by a dynamic IP user a DDNS service though can map such dynamic IP addresses to a fixed hostname for easier access The router supports several DDNS service providers for more details and to register for a DDNS account please visit the DDNS providers website s examples of which are listed below DDNS Enable Disable Enable Disable Provider DynDNS Domain Name Account E mail Password Key Save Settings Enable Disable Enable or disable DDNS Select DDNS service provider Domain Name Enter the domain name provided by the DDNS provider Account Email Please enter the DDNS registration account email Password Key Enter the DDNS service password key The following DDNS services are supported 3322 http www 3322 org DHS http www dhs org DynDNS http www dyndns org ODS http ods org TZO http www tzo com GnuDIP http gnudip2 sourceforge net DyNS http www dyns cx ZoneEdit http www zoneedit com CyberGate http cybergate planex co jp ddns NS2GO http www ns2go com NO IP http www noip com 111 4 4 LAN You can configure your Local Area Network LAN on LAN thi
65. efer to V 1 Configuring your IP address for more information Ill 1 Login 1 To access the browser based configuration interface enter http edimax setup into the URL bar of a browser on a network device connected to the same Wi Fi network as the EW 7208APC B E in Tm http edimax setup A If you can not access http edimax setup connect the device to a Computer using an Ethernet cable and try again 2 You will be prompted for a username and password The default username is admin and the default password is 1234 Connect to edimax setup The server edimax setup at Default Name admin Password 1234 requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name FK admin Password TID Remember my password 3 You will arrive at the Status screen Use the menu down the left side to navigate Access Point HETWORKING PEOPLE TOGETHER Status Help Setup Wizard system Status LAN O PAN YO Model Access Point IF Address 192 158 0 107 2 4GHz Wireless Current Time 2014 9 15 21 42 21 Subnet Mask 255 255 255 0 5GHz Wireless Hardware Version Rev A MAC Address 74 DA 38 0x 61 50 Firmware Version 1 01 Advanced Administration 2 4GHz Wireless Mode Access Point Mode Access Point SSID edimax 2 4G 035150 SSID
66. er your existing Wi Fi network security key if required Device SSID 6208ac 5G Security Key 6 Wait a moment while the EW 7208APC tests the wireless connection Wireless Bridge Testing wireless connection 7 Select Obtain an IP address automatically or Use the following IP address for your EW 7208APC If you are using a static IP enter the IP address subnet mask and default gateway Click Next to proceed to the next step a Obtain an IP address automatically is the recommended setting A for most users The IP address will be displayed in brackets 5 MAX Wireless Bridge Connection test cpmplete Please click Next when you are ready to continue Obtain an IP address automatically IP 192 168 2 102 O Use the following IP address IP address 192 Subnet Mask 255 Default gateway 0 DNS 0 8 A summary of your configuration will be displayed as shown below Check that all of the details are correct and then click Next to proceed w LD E MAX Wireless Bridge Configuration is complete It is recommended that you backup your settings please click Backup this configuration to do so Then click Next when you are ready to continue IP address 192 168 2 102 5 GHz Wi Fi network name 6208ac_5G Wi Fi password abcd1234 Backup this configuration If you wish to backup the EW 7208APC s settings click Backup A this configuration to
67. ess radio You may not require 10096 output power Setting a lower power output can enhance security since potentially malicious unknown users in distant areas will not be able to access your signal WMM Wi Fi Multimedia technology can improve the performance of certain network applications such as audio video streaming network telephony VoIP and others When WMM is enabled the device will prioritize different kinds of data and give higher priority to applications which require instant responses for better performance Ill 3 6 Administration Various administrative functions can be accessed from the Administration menu a Administration Time Zone Password Backup Restore Upgrade Restart 111 3 6 1 Time Zone Time Zone Set Time Zone GMT Greenwich Mean Time Dublin Edinburgh Lisbon London o Time Server Address pool ntp org Enable Function January 1 To January 1 Daylight Savings Save Settings Set Time Zone Select the time zone of your country or region Time Server Address The travel router supports NTP Network Time Protocol for automatic time and date setup Input the host name of the IP server manually Daylight Saving If your country region uses daylight saving time please check the Enable Function box and select the start and end date lll 3 6 2 Password You can change the password used to login to the browser based configuration interface here It
68. et ja muut asiaankuuluvat m r ykset WEEE Directive amp Product Disposal E At the end of its serviceable life this product should not be treated as household or general waste It di should be handed over to the applicable collection point for the recycling of electrical and electronic mem equipment or returned to the supplier for disposal Declaration of Conformity We Edimax Technology Co Ltd declare under our sole responsibility that the equipment described below complies with the requirements of the European R amp TTE directives Equipment AC750 Multi Function Dual Band Wi Fi Access Point Model No EW 7208APC The following European standards for essential requirements have been followed Directives 1999 5 EC Spectrum ETSI EN 300 328 V1 8 1 2012 06 ETSI EN 301 893 V1 7 1 2012 06 EMC EN 301 489 1 V1 9 2 2011 09 EN 301 489 17 V2 2 1 2012 09 Safety LVD EC 60950 1 2005 2 Edition Am 1 2009 EN 60950 1 2006 A11 2009 A1 2010 A12 2011 Recommendation19 99 5 EC EMF EN 62311 2008 Directives 2006 95 EC Safety LVD EC 60950 1 2005 2 Edition Am 1 2009 EN 60950 1 2006 A11 2009 A1 2010 A12 2011 Edimax Technology Co Ltd No 3 Wu Chuan 3 Road Wu Ku Industrial Park New Taipei City Taiwan Date of Signature September 2014 CEO v gc Printed Name Albert Chang Title Director Edimax Technology Co Ltd DIMAX NETWORKING PEOPLE TOGETHER
69. ettings Optimize visual display View your basic network information and set up connections qe x TS WIN7 This computer View your active networks Access type Home network YP Home network HomeGroup General See full map Internet Connect or disconnect Mo Internet access Local Area Connection IPw4 Connectivity No Internet access IPv6 Connectivity No network access Media State Enabled Duration 02 08 52 Speed 100 0 Mbps Details Sent A Received 951 332 4 398 184 pr 5 Select Internet Protocol Version 4 TCP IPv4 and then click Properties li Local Area Connection Properties u Networking Connect using amp Broadcom 44 x 10 100 Integrated Controller Configure This connection uses the following items JE Client for Microsoft Networks ba QoS Packet Scheduler w Erie an and Printer for Microsoft Networks wi ntemet Protocol Version 4 Unk Layer Toporody Discovery Mapper 1 0 Driver er ls Topology Discovery Responder O PY SSS Install Uninsta Properties Description TCP IP version 6 The latest version of the intemet protocol that provides communication across diverse interconnected networks 6 Select Use the following IP address and Use the following DNS server addresses then input the following values Your existing static IP address will be displayed in the IP
70. etwork to connect to A OBM AirPort 24G Security enabled network A EDIMAXIP Cam 24G Security enabled network Set up a connection or network Open Network and Sharing Center rs 3 After correctly entering your password you will be successfully connected to the EW 7208APC s wireless network Successfully connected to edimax setup Save this network Start this connection automatically IV 3 Troubleshooting 1 In range extender mode is my EW 7208APC dual band a Yes The EW 7208APC can extend 2 4GHz amp 5GHz Wi Fi signals concurrently but you must connect your EW 7208APC to each 2 4GHz amp 5GHz network separately during iQ setup During iQ Setup you will be asked to select both a 2 4GHz amp 5GHz Wi Fi network to extend as well as specify a new SSID name and password for each of the networks that your EW 7208APC s will broadcast extend N You can disable either 2 4GHz or 5GHz Wi Fi during iQ setup if EE there is no appropriate source network available or if you do not wish to use it If either the 2 4GHz or 5GHz frequency band is disabled wireless clients devices on the same frequency band will be unable to connect to your range extender 2 In range extender mode if my EW 7208APC is set up as a dual band extender what happens when connect a wired Ethernet client a When you connect a network device to your EW 7208APC in range extender mode via Ethernet cable by default the network device
71. ght field to define a range of IP addresses or enter an IP address in the left field only to define a single IP address Remote Port Range Enter the remote port range to activate the QoS rule Enter a single port number e g 110 ora range of port numbers e g 110 120 Traffic Type Select traffic type as an alternative to specifying a port range above Select a TCP or UDP protocol type Click add button to add a new QoS rule detailed instructions will be given below QoS rule entries will be listed in the Current QoS Table as shown below Select a rule using the Select checkbox A When using the Edit button only one rule can be selected each a time A QoS rules will be processed in the order that they are listed i e E the rule at the top of the list will be applied first and then the second rule etc The order can be adjusted using the Move Up Down buttons Current QoS Table Rule Name Upload Bandwidth Add zdi f Delte Salaried Ra EA AS Edit Edita selected rule Delete Selected Delete selected or all entries from the Delete All table Move Up Down Move selected rule up or down the list Ill A 7 2 iQoS iQoS is a more intuitive and automated tool to manage internet bandwidth than manually configuring the settings using QoS For online gamers or users with bandwidth requirements for audio video iQoS is a useful function A iQoS cannot be used in conjunctio
72. he instructions appropriate for your operating system If you are using Windows XP or earlier please contact your ISP or router manufacturer to find your network security key PY IV 1 3 1 Windows 7 amp Vista 1 Open Control Pane menu and click on Network and Internet in the top File Edt View Tools Advanced Help Organize x a Local Area Wireless Connection Network Connection 19 2 Click on View network status and tasks which is under the heading Network and Sharing Center elie File Edit View Tools Help Control Panel Home System and Security DU DU DL Network and Internet Add a wireless device to the network Hardware and Sound ad HomeGroup Programs Choose homegroup and sharing options User Accounts and Fami Safety y i Internet Options Change your homepage Manage browser add ons A d coc beg Delete browsing history and cookies Personalization 3 Click on Manage wireless networks in the left menu 55 Networkan Network and Sharing Center File Edit View Tools Help Control Panel Home View your basic network information and set up Manage wireless network connections See full map f Change adapter settings A T Change advanced sharing E TS PC HomeNetwork 2 Internet settings This computer See also View your active networks Connect or disconnect HomeGroup Access type Internet Inter
73. her in a relatively small area such as a house or an office Your home network is considered a LAN MAC Address MAC stands for Media Access Control A MAC address is the hardware address of a device connected to a network The MAC address is a unique identifier for a device with an Ethernet interface It is comprised of two parts 3 bytes of data that corresponds to the Manufacturer ID unique for each manufacturer plus 3 bytes that are often used as the product s serial number NAT Network Address Translation This process allows all of the computers on your home network to use one IP address Using the broadband access point s NAT capability you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP Port Network Clients LAN PC uses port numbers to distinguish one network application protocol over another Below is a list of common applications and protocol port numbers Application Protocol Port Number Telnet TCP 23 FTP TCP 21 SMTP TCP 25 POP3 TCP 110 H 323 TCP 1720 SNMP UCP 161 SNMP Trap UDP 162 HTTP TCP 80 PPTP TCP 1723 PC Anywhere TCP 5631 PC Anywhere UDP 5632 Access point A access point is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses Subnet Mask A subnet mask which may be a part of the TCP IP information provided by your ISP is a set of four num
74. in this network Not Connected ee V Ask to join new networks Bluetooth PAN o Known networks will be joined automatically If no known networks are available you will be asked before joining a new network Not Connected v Show Wi Fi status in menu bar e in i m id Click the lock to prevent further changes Assist me Revert 4 Click the TCP IP tab and your router s IP address will be displayed next to Router Network Ls gt Show All T Configure IPv4 Using DHCP IPv4 Address 10 0 20 97 Renew DHCP Lease Subnet Madii amd DHCP Client ID lf required 10 0 20 254 Configure IPv6 Automatically Router IPv6 Address Prefix Length Cancel OK IV 2 Connecting to a Wi Fi network For help connecting to your device s Edimax Setup SSID for initial setup or to connect to your device s new Wi Fi network SSID after setup is complete follow the guide below A Below is an example of how to connect using Windows Vista the gt process may vary slightly for other versions of Windows 1 Click the network icon E uno in the system tray and select Connect to a network Mot Connected A Wireless networks are available DEPE 70629 2 Search for the SSID of your EW 7208APC and then click Connect If you set a password for your network you will then be prompted to enter it Select a n
75. ing box to enable disable URL blocking URL Blocking Enable URL Blocking URL Keyword Add 1 www blockedwebsite com E Delete Selected Delete All Save Settings Settings have been saved Please click here to restart the router and bring the new settings into effect URL Keyword Enter the URL or keyword to be blocked Add the URL or keyword to the blocked table Blocked URLs keywords entries will be listed in the table as shown below Select an entry using the Select checkbox 1 www hblockedwebsite com E Delete Selected Delete All Save Settings Settings have been saved Please click here to restart the router and bring the new settings into effect Delete Selected Delete selected or all entries from the table Delete All 1ll A 6 2 Access Control A Access Control MAC filtering can also be configured from 111 4 5 4 Access Control Access Control is a security feature that can help to prevent unauthorized users from connecting to your wireless router This function allows you to define a list of network devices permitted or denied to connect to the EW 7208APC Devices are each identified by their unique MAC address or IP address Specific services can also be allowed denied for IP addresses Check uncheck the Enable MAC Filtering and or Enable IP Filtering box to enable disable MAC filtering and or IP filtering Access Control Enable MAC Filtering C Deny Allow Client PC MAC
76. ion DHCP Dynamic Host Configuration Protocol This protocol automatically gives every computer on your home network an IP address DNS Server IP Address DNS stands for Domain Name System which allows Internet servers to have a domain name such as www Broadbandaccess point com and one or more IP addresses such as 74 125 128 104 A DNS server keeps a database of Internet servers and their respective domain names and IP addresses so that when a domain name is requested as in typing Broadbandaccess point com into your Internet browser the user is sent to the proper IP address The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you DSL Modem DSL stands for Digital Subscriber Line A DSL modem uses your existing phone lines to transmit data at high speeds Ethernet A standard for computer networks Ethernet networks are connected by special cables and hubs and move data around at up to 10 100 million bits per second Mbps IP Address and Network Subnet Mask IP stands for Internet Protocol An IP address consists of a series of four numbers separated by periods that identifies a single unique Internet computer host in an IP network Example 192 168 2 1 It consists of 2 portions the IP network address and the host identifier The IP address is a 32 bit binary pattern which can be represented as four cascaded decimal numbers separated by aaa
77. is 192 168 2 1 The procedure for modifying your IP address varies across different operating systems please follow the guide appropriate for your operating system in IV 1 2 How to modify the IP address of your computer N Static IP users please make a note of your static IP before you change it You can assign a new IP address to the device which is within the subnet of your network during setup or using the browser based configuration interface refer to 111 3 4 LAN Then you can access the URL http edimax setup in future without modifying your IP address 4 h Please remember to change your IP address back to ts original value after the device is properly configured IV 1 1 How to check that your computer uses a dynamic IP address Please follow the instructions appropriate for your operating system IV 1 1 1 Windows XP 1 Click the Start button it should be located in the lower left corner of your computer then click Control Panel Double click the Network and Internet Connections icon click Network Connections and then double click Local Area Connection The Local Area Connection Status window will then appear click Properties l Local Area Connection Properties General Authentication Advanced Connect using Eg AMD PENET Family PCI Ethernet Ad This connection uses the following items Client For Microsoft Networks EF Description Transmission Control Protacal
78. is advised to do so for security purposes Please make a note of the new password In the event that you forget the password and are unable to login to the browser A based configuration interface see Il 7 Reset to factory default settings for how to reset the device Password Current Password New Password Confirmed Password Current Password Enter your current password Enter your new password Confirmed Password Confirm your new password lll 3 6 3 Backup Restore Backup Restore Backup Settings Browse Restore Settings Restore to Factory Default Reset Backup Settings Click Save to save the current settings on your computer as config bin file Restore Settings Click Browse to find a previously saved config bin file and then click Upload to replace your current settings Restore to Click Reset to restore settings to the factory Factory Default default A pop up window will appear and ask you to confirm and enter your log in details Enter your username and password and click Ok See below for more information Ill 3 6 4 Upgrade The upgrade page allows you to upgrade the system firmware to a more recent version You can download the latest firmware from the Edimax website After the upgrade the system will restart A Do not switch off or disconnect the device during a firmware 2 upgrade as this could damage the device It is recommended that you use a wired Ether
79. l network You can define a virtual DMZ host here This is useful for example if a network client PC cannot run an application properly from behind an NAT firewall since it opens the client up to unrestricted two way access DMZ Fl Enable DMZ e Dynamic IP Session 1 EM select lil t Static IP Current DMZ Table Computer Name Public IP Address Client PC IP Address Delete Ses arti ese Delete x Save Settings Enable DMZ Check uncheck the box to enable disable the device s DMZ function Select Dynamic IP or Static IP here For Dynamic IP select an Internet connection session from dropdown menu For Static IP enter the IP address that you want to map to a specific private IP address Client PC Enter the private IP address that the internet IP address will be mapped to Computer Name Select a computer name from the list and click lt lt to enter its IP address into the Client PC field above Click Add to add the client to the Current DMZ Table DMZ entries will be displayed in the table shown below Current DMZ Table Computer Name Public IP Address Delete Selected Delete selected or all entries from the table Delete All Ill 4 6 4 DoS Denial of Service DoS is a common form of malicious attack against a network The router s firewall can protect against such attacks If you are not familiar with these functions it is recommended yo
80. l Server 2 4GHz Wireless 5GHz Wireless IGMP UPnP 111 4 8 1 Static Routing Static routing is a method of configuring path selection of routers characterized by the absence of communication between routers regarding the current topology of the network The opposite of static routing is dynamic routing sometimes also referred to as adaptive routing You can configure static routing and manually add routes to the routing table shown below Static Routing Fl Enable Static Routing Destination LAN IP Subnet Mask Default Gateway Hop Count LAN v Add Current Static Routing Table NO Destination LAN IP Subnet Mask Default Gateway Hop Count i Save Settings l Enable Static Routing Check uncheck the box to enable disable static routing Destination LAN IP Enter the destination network s IP address ead network Enter the default gateway of the destination network Hop Count Enter the hop count the distance between destination network and this broadband router here ea NN destination network A an table Static Routing Table entries will be displayed in the table shown below Current Static Routing Table Eo DestinationtaN IP subnet Mask Default Gateway Hop Count interface Select Delete Selected Delete selected or all entries from the table Delete All I11 4 8 2 Port Forwarding This function allows you to redirect a single port or consecutive ports of an Internet IP ad
81. laces 4 Libraries b ES Documents b A Music gt i Pictures gt B Videos gt ME Computer Cu Network Expand Open in new window Pin to Start Map network drive Disconnect network drive v Search Network This folder is empty 2 53 PM A B 0 Px ox 73 2012 4 In the window that opens select Change adapter settings from the left side Library Tools Home Share View Manage Manage Ft Favorites BE Desktop Downloads S Recent places T D Network and Internet Network and Sharing Center Control Panel Home A Libraries ES Documents Change adapter settings 2 Music e i Pictures settings B Videos View your active networks Network Public network Change your networking settings jE Computer Cu Network Troubleshoot problems Set up a new connection or network Pictures Search Pictures v Search Control Panel v View your basic network information and set up connections Access type Internet Connections J Ethernet Set up a broadband dial up or VPN connection or set up a router or access point Diagnose and repair network problems or get troubleshooting information See also HomeGroup Internet Options Windows Firewall litem 1item selected Library includes 2 locations 2 54 PM 12 3 2012 92 ox D Choose your connection and right click then select Properties Network View Gi gt Network v v
82. n to your xDSL modem The LAN ports are for wired network clients e In WISP mode the Internet port is not functional and the all of LAN ports are for wired network clients 11 A firmware upgrade failed and the EW 7208APC isn t working Firmware upgrade failures can happen occasionally due to power cuts or unstable connections In this scenario you need to first connect a computer to one of your EW 7208APC s LAN ports using an Ethernet cable Then you need to modify your computer s IP address to 192 168 2 x where x is any value between 3 and 254 Refer to IV 1 2 How to modify the IP address of your computer if you need guidance to do so From there you need to go to 192 168 2 1 in a web browser and you will see the page below Firmware Recovery Mode Please select the correct firmware file than click Upload once and wait for the next screen to display that the upgrade is in progress Browse Upload Click Browse to locate the firmware file on your computer and then click Upload to upload the new firmware It may take several minutes to complete please wait and follow the instructions on screen V Glossary Default Gateway Wireless bridge Every non access point IP device needs to configure a default gateway s IP address When the device sends out an IP packet if the destination is not on the same network the device has to send the packet to its default gateway which will then send it out towards the destinat
83. n with QoS and vice versa When one is enabled the other is automatically disabled i QoS 005 is a smart tool for bandwidth management i005 cannot be used simultaneously with Cos 7 Enable iQoS Total Download Bandwidth O kbits Total Upload Bandwidth 0 kbits Current iQo5 Table Taye Settings Settings have been saved Please click here to restart the router and bring the new settings into effect Check uncheck the box Enable iQoS to enable disable the iQoS function and then enter your bandwidth limits and arrange the network application icons in priority order in the Current iQoS Table Icons with higher priority will be assigned bandwidth more efficiently for better performance Total Download Enter your total download bandwidth limit Bandwidth from your Internet service provider ISP in kbits Total Upload Enter your total upload bandwidth limit from Bandwidth your Internet service provider ISP in kbits The icons represent the following categories Internet Browsing P2P BT Downloads Multimedia Online Gaming The iQoS table is ordered left to right high to low priority Click a small icon below the table to insert it into the table and click a large icon in the table to remove it All spaces in the priority table must be filled 111 4 8 Advanced Advanced features of the EW 7208APC can be A A OR USE configured from the Advanced menu Static Routing Port Forwarding Virtua
84. nction of your device Keep the default AP value for the device to act as a standard wireless access point or select AP Bridge WDS for the device to function in WDS mode see below Displays the wireless standard used for the EW 7208APC s 2 4GHz b g n means that 802 11b 802 11g and 802 11n wireless clients can connect to the EW 7208APC Wireless Network This is the name of your Wi Fi network for Name SSID identification also sometimes referred to as SSID The SSID can consist of any combination of up to 32 alphanumerical characters Broadcast SSID Enable or disable SSID broadcast When enabled the SSID will be visible to clients as an available Wi Fi network When disabled the SSID will not be visible as an available Wi Fi network to clients clients must manually enter the SSID in order to connect A hidden disabled SSID is typically more secure than a visible enabled SSID Enable Wireless Clients Isolation Channel Number Site Survey Wireless Clients Check the box to enable wireless clients isolation This prevents wireless clients connected to the EW 7208APC from communicating with each other and improves security Typically this function is useful for corporate environments or public hot spots and can prevent brute force attacks on clients usernames and passwords Select a wireless radio channel or use the default Auto setting from the drop down menu Click Show Lis
85. nd Internet Network and Sharing Center v 0 Search Control Panel YE Recent places View your basic network information and set up connections Libraries 3 Documents Change adapter settings RU Music ES Network Access type Internet Pictures settings Public network Connections I Ethernet B Videos View your active networks Change your networking settings Computer P Set up a new connection or network Set up a broadband dial up or VPN connection or set up a router or access point Cu Network Troubleshoot problems Diagnose and repair network problems or get troubleshooting information See also HomeGroup Internet Options Windows Firewall litem 1item selected Library includes 2 locations 2 54 PM 12 3 2012 i T tk D Choose your connection and right click then select Properties ii2is File Network View T Gm gt Network v Network discovery and file sharina are turned off Network computers and devices are not visible Click to chanae l BG Network and Sharing Center YX Favorites BE Desktop Je Downloads T TU Network and Internet Network Connections Search Network Connections S Recent places Organize v Disable this network device Diagnose this connection Rename this connection ae a Libraries ES Documents 2 Music E Pictures B Videos Diagnose Wy Bridge Connections Wy Disable Status Computer Create Shortcut Delete Wy Rename lt
86. nd of an Ethernet cable to your existing router and connect the other end to one of the ports 1 2 3 4 on the back of access point 3 Select whether to use the 5GHz wireless frequency 2 4GHz wireless frequency or both If you are not sure select both EDIMAX Access Point Please select the wireless frequency that you want to use If you are not sure which one to use please select both Y 1 Enable 5GHz Y 2 Enable 2 4GHz 4 Select Obtain an IP address automatically or Use the following IP address for your EW 7208APC If you are using a static IP enter the IP address subnet mask and default gateway Click Next to proceed to the next step Access Point Please set the IP address of the access point Obtain an IP address automatically Use the following IP address IP address 192 Subnet Mask Default gateway 0 DNS 0 pu A Obtain an IP address automatically is the recommended setting 2 for most users For more guidance on static IP addresses please refer to IV 1 Configuring your IP address D Enter a name and password for your 2 4GHz amp 5GHz wireless networks then click Next to continue EDIMAX Access Point Please set your Wi Fi network name SSID and Wi Fi password Wi Fi network name 2 4GHz edimax_2 4G_75EDFB Wi Fi password WPA2 AES abcd1234 at least 8 characters Wi Fi network name 5GHz ledimax 5G 75EEO0 Wi Fi
87. net Cintinnc Connections 4r Wireless Network 4 You should see the profile of your Wi Fi network in the list Right click on your Wi Fi network and then click on Properties Add Remove Movedown Adapter properties Profile types Networks you can view modify and reorderi M Eee O O O M Ww HomeNetwork Security WPA2 Personal Remove network Rename Move down 5 Click on the Security tab and then check the box labeled Show characters This will show your network security key Click the Cancel button to close the window IV 1 3 2 Mac 1 Open a new Finder window and select Applications from the menu on the left side Open the folder labeled Utilities and then open the application Keychain Access six Applications Ed m mj H m FAVORITES Nam e a Date Modified Desktop z TextEdit 2012 2 2 47 08 Time Machine 2012 2 2 7 08 Cs Utilities 2012 2 2 FF 3 32 q AX Applications ettvity Monitor 2012 2 2 FF7 08 AirPort Utility 2012 2 2 TF 7 08 7 AppleScript Editor 2012 2 2 T F7 08 Im Audio MIDI Setup 2012 2 2 T F7 08 DEVICES gt Bluetooth File Exchange 2012 2 2 T F7 08 E 10 6 4 Boot Camp Assistant 2012 2 2 T F7 08 ColorSync Utility 2012 2 2 T F7 08 EB Console 2012 2 2 FF 7 08 amp DigitalColor Meter 2012 2 2 TF 7 08 E UL 42 Dropbox Es Disk Utility 2012 2 2 T F7 08 P Grab 2012 2 2 7 08 Grapher 2012 2 2 T F7 08 il Java Prefe
88. net connection for a firmware upgrade Upgrade Browse lll 3 6 5 Restart In the event that the router malfunctions or is not responding then it is recommended that you restart the device Restart In the event that the system stops responding correctly or stops functioning you can perform a system restart Your settings will not be changed To restart click on the APPLY button below You will be asked ta confirm your decision The restart will be complete when the Internet LED light stops blinking Apply lll 4 Main Menu Other Modes The main menu displays different options depending on your device s operating mode A For WPS function in Range Extender mode please refer to 2 4GHz Wireless amp 5GHz Wireless gt WPS Wi Fi Router Range Extender Wireless Bridge WISP Status Status Status Status Setup Wizard Setup Wizard Setup Wizard Setup Wizard Internet WPS Administration WISP LAN Administration LAN 2 4GHz Wireless 2 4GHz Wireless 5GHz Wireless 5GHz Wireless Firewall Firewall QoS QoS Advanced Advanced Administration Administration 111 4 1 Status The Status page displays basic system information Status about the device arranged into categories A Screenshots displayed are examples The information shown on your screen will vary depending on your configuration EDIMAX Wi Fi Router NETWORKING PEOPLE TOGETHER Status System S
89. ng window EdimaxWireless Name EdimaxWireless Kind AirPort network password Account AirPort Where com apple network wlan ssid EdimaxWireless Comments Show password Save Changes 4 Check the box labeled Show password and you will be asked to enter your administrative password which you use to log into your Mac Enter your password and click Allow Keychain Access wants to use your confidential information stored in EdimaxWireless in your keychain To allow this enter the login keychain password Always Allow Deny Allow com apple network wlan ssid EdimaxWireless Comments Save Changes Your network security password will now be displayed in the field next to the box labeled Show password In the example below the network security password is edimax1234 Please make a note of your network security password EdimaxWireless Attributes MA Access Control Name EdimaxWireless Kind AirPort network password Account AirPort Where com apple network wlan ssid EdimaxWireless Comments Show password edimax1234 Save Changes IV 1 4 How to Find Your Router s IP Address To find your router s IP address please follow the instructions appropriate for your operating system IV 1 4 1 Windows XP Vista amp 7 1 Goto Start select Run and type cmd then press Enter or click OK Internet
90. nnection specific DHS Suffix C SUsers AlanChiu gt IV 1 4 2 Windows 8 1 From the Windows 8 Start screen move your curser to the top right corner of the screen to display the Charms bar Trending Rick Majerus Katt Williams slap Hugh Hefner Calendar Internet Explorer Store 15 Bing Photos Maps SkyDrive idi dil Y Games Camera E Za 1416 18 A 0 02 0 23 E a Fort Worth Star Telegram LeBreton 11 30 2012 4 38 PM EST ae caes Cowboys win shows there s still hope ru December N 2 Click Search and enter cmd into the search bar Click the Command Prompt app which be displayed on the left side A 9 9 S Results for cmd Command Prompt Command Prompt icrosoft Windows Version 6 2 9206 lt c 2012 Microsoft Cownorat ion WsersW in8 gt ipconf ig All rights reserved Search Apps cmd o Settings i Files O Bing Finance M Games Ps e Internet Explorer 4 Your router s IP address will be displayed next to Default Gateway Command Prompt Jindovus IP Configuration Ethernet adapter Ethernet Connection specific DNS Suffix Link local IPv6 Address gt fea 202140 Ah 19e7 3005712 IPo4 nddPess i1 1 2 ee ee 77172 168 12 115 subnet Mask ooo ee ee O o A A Default Gateway E m m m We Lee N A i 12 202 unnel adapter isatap tDEA021 43 5404 453D BD50 306440BE93A732 gt Media State a Media disconnected
91. nt Threshold 2346 256 2346 RTS Threshold 2347 0 2347 Beacon Interval 100 20 1024 ms DTIM Period 3 1 10 Data Rate Auto I M Data Rate Auto EB Channel Width 9 Auto 20 40 MHZ 20 MHZ Preamble Type 9 Short Preamble Long Preamble CTS Protect J Auto Always Y None Tx Power 100 i WMM 9 Auto radio The default value is 2346 The default value is 2347 The default value is 100 Set the DTIM period of wireless radio The default value is 3 default is set to Auto set to Auto Channel Width Select wireless channel width bandwidth used by wireless signals from the device the recommended value is Auto 20 40MHz Preamble Type Set the wireless radio preamble type The default value is Short Preamble CTS Protect Enabling this setting will reduce the chance of radio signal collisions between 802 11b and 802 11g wireless access points It s recommended to set this option to Auto Tx Power Set the power output of the wireless radio You may not require 10096 output power Setting a lower power output can enhance security since potentially malicious unknown users in distant areas will not be able to access your signal WMM Wi Fi Multimedia technology can improve the performance of certain network applications such as audio video streaming network telephony VoIP and others When WMM is enabled the device will prioritize different kinds of data and give higher priority to applications which require in
92. nual or otherwise without the prior written permission from Edimax Technology Co Ltd Edimax Technology Co Ltd makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Any software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not this company its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software Edimax Technology Co Ltd reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes The product you have purchased and the setup screen may appear slightly different from those shown in this QIG The software and specifications are subject to change without notice Please visit our website www edimax com for updates All brand and product names mentioned in this manual are trademarks and or registered trademarks of their respective holders Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection
93. on compatible devices by pushing a WPS button on the device or from within the device s firmware configuration interface When WPS is activated in the correct manner and at the correct time for two compatible devices they will automatically connect PIN code WPS includes the use of a PIN code between the two devices for verification WPS V Enable WPS Wi Fi Protected Setup Information WPS Status Configured Self Pin Code 91486257 SSID edimax_2 4G_EDF2D1 Authentication Mode WPA Pre shared Key Authentication Key abcd1234 Device Configuration Configuration Mode Registrar Configure via Push Button Start PBC Configure via Client Pin Code Start PIN Enable WPS Check uncheck this box to enable disable WPS Displays Configured or unConfigured depending on whether WPS and SSID security settings for the device have been configured or not either manually or using the WPS button So RE Authentication Displays the wireless security authentication Mode mode of the device Authentication Key Displays the wireless security authentication key Configuration The configuration mode of the device s WPS Mode setting is displayed here Registrar means the device acts as an access point for a wireless client to connect to and the wireless client s will follow the device s wireless settings Configure via Push Click Start PBC Push Button Configuration Button to activate WPS on the access point WPS will be active for
94. ons virtually EE instead of physically and allows you to group together or isolate users from each other VLAN IDs 0 4094 are supported Encryption Ill 3 A4 3 WPS Wi Fi Protected Setup is a simple way to establish connections between WPS compatible devices WPS can be activated on compatible devices by pushing a WPS button on the device or from within the device s firmware configuration interface When WPS is activated in the correct manner and at the correct time for two compatible devices they will automatically connect PIN code WPS includes the use of a PIN code between the two devices for verification WPS V Enable WPS Wi Fi Protected Setup Information WPS Status Configured Self Pin Code 91486257 SSID edimax 2 4G EDF2D1 Authentication Mode WPA Pre shared Key Authentication Key abcdi234 Device Configuration Configuration Mode Registrar Configure via Push Button Start PBC Configure via Client Pin Code Start PIN Enable WPS Check uncheck this box to enable disable WPS Displays Configured or unConfigured depending on whether WPS and SSID security settings for the device have been configured or not either manually or using the WPS button Self PIN Code Displays the WPS PIN code of the device SSID JjDisplaysthe SSID of the device Authentication Displays the wireless security authentication Mode mode of the device Authentication Key Displays the wireless security authentication key
95. operate as usual and click on System Preferences System Preferences 2 In System Preferences click on Network Internet amp Network l s Taaa C MobileMe Network QuickTi me Sharing 3 Click on Wi Fi in the left panel and then click Advanced in the lower right corner eoo Network 4 gt ShowAll Location Automatic Status Connected Turn Wi Fi Off Wi Fi is connected to OBM AirPort 2 4G and e Et i ood has the IP address 192 168 77 119 a iniri Qe Network Name OBM AirPort 2 4G V Ask to join new networks Known networks will be joined automatically If no known networks are available you will e FireWire be asked before joining a new network 802 11 n WLAN e G0 e Bluetooth ius V Show Wi Fi status in menu bar Advanced Y mv fi id Click the lock to prevent further changes Assist me Apply 4 Select TCP IP from the top menu and Using DHCP in the drop down menu labeled Configure IPv4 should be selected 000 gt Wi Fi wi Ea Ds WINS 802 1X Proxies Hardware Configure ESA CE S PA With manual address Using BootP Renew DHCP Lease Manually D If required Configure IPv6 Router IPv6 Address Prefix Length IV 1 2 How to modify the IP address of your computer Please follow the instructions appropriate for your operating system In the following examples we
96. ormat Choose from ASCII any alphanumerical character 0 9 a z and A Z or Hex any characters from 0 9 a f and A F Encryption Key Enter your encryption key password according to the format you selected above A complex hard to guess key is recommended Check the Hide box to hide your password from being displayed on screen Enable 802 1x Check the box to enable the 802 1x Authentication authentication A RADIUS server is required to perform 802 1x authentication enter the RADIUS server s information in the relevant fields below V Enable 802 1x Authentication RADIUS Server IP address RADIUS Server Port 1812 RADIUS Server Password 111 3 4 1 3 WPA Pre Shared Key WPA pre shared key is the recommended and most secure encryption type Wireless Security Encryption WPA Pre shared Key WPA Unicast Cipher Suite WPA TKIP CO WPA2 AES WPA2 Mixed Pre shared Key Format Passphrase Pre shared Key 4 Hide WPA Unicast Select from WPA TKIP WPA2 AES or WPA2 Cipher Suite Mixed WPA2 AES is safer than WPA TKIP but not supported by all wireless clients Please make sure your wireless client supports your selection WPA2 AES is recommended followed by WPA2 Mixed if your client does not support WPA2 AES Pre shared Key Choose from Passphrase 8 63 Format alphanumeric characters or Hex up to 64 characters from 0 9 a f and A F Pre shared Key Please enter a key according to the fo
97. ot put the device in the corner of a room or under nearby metal c Ensure there are as few obstacles as possible between the EW 7208APC and your wireless network device In range extender mode the EW 7208APC s weak wireless signal may be in turn caused by a weak signal from your existing router It s important to choose a good location for the EW 7208APC in relation to your existing wireless router The best location is roughly in the middle between your existing wireless router and the area you would like to be covered by the EW 7208APC If you are too far away from your existing router then it is difficult for the EW 7208APC to receive a wireless signal 10 Do the Internet and LAN ports work the same when the device is in different modes No the Internet and LAN ports have slightly different functions depending on the operating mode of the device a In access point mode the Internet port is not functional Connect your existing router to the device s LAN port and the other LAN ports can connect wired network clients b In range extender mode the Internet port is not functional and the all of LAN ports are for wired network clients Do not connect your existing router to the device s Internet or LAN ports as this can cause the device to malfunction c In wireless bridge mode the Internet port is not functional and the all of LAN ports are for wired network clients d In Wi Fi router mode the Internet port is for a direct connectio
98. pleted setup Please connect to the device s new Wi Fi network name SSID listed below For advanced settings please access http edimax setup from your computer s web browser 2 4 GHz Wi Fi network name edimax_2 4G_75EDFB Wi Fi password abcd1234 5 GHz Wi Fi network name edimax_5G_75EE0O Wi Fi password abcd1234 9 The EW 7208APC is working and ready for use Refer to IV 2 Connecting to a Wi Fi network if you require more guidance Il 2 Range Extender Mode 1 Select Range Extender from the top menu and click Next EDIMAX Range Extender You have selected Range Extender Mode The product connects wirelessly to your existing network and extends the wireless signal range 2 Please ensure your EW 7208APC is within Wi Fi range of your existing wireless router Click Next to continue Range Extender xDSL Cable Modem This setup wizard will assist you to setup a wireless connection between the range extender and your existing router Place the range extender close to the area where you wish to extend your network but please ensure the range extender is still within the coverage range of your existing wireless network E c 3 Select whether to use the 5GHz wireless frequency 2 4GHz wireless frequency or both If you are not sure select both and then click Next mm EDIMAX Range Extender Please select the wireless frequency that same as your existing wirelesss network
99. rences 2012 7 17 F 10 54 Keychain Access 2012 2 2 F 47 08 2 Midraton Assistant 2012 2 2 T F7 08 abismal Pei lies ao 4i 7a TUO 0773 T Ar Triad 2 Select Passwords from the sub menu labeled Category on the left side as shown below Then search the list in the main panel for the SSID of your network In this example the SSID is EdimaxWireless though your SSID will be unique to your network eoo Keychain Access tL Click to lock the login keychain Keychains cf login amp System EdimaxWireless Kind AirPort network password Account AirPort E System Roots Where com apple network wlan ssid EdimaxWireless Modified Today FF5 45 Kind JN Apple ID Authentication application password JN Apple Persistent 5tate Encryption application password jy EDIMAX 6475 AirPort network password Category a Elda AirPort network password UM EdimaxWireless AirPort network password 7 aT NEA m E application password Passwords PP P UM Matt AirPort network password d A PP 6574 Demo AirPort network password EJ My Certificates t Keys E Certificates Date Modified 2012 7 17 F 10 16 29 2012 7 16 T F5 15 20 2012 7 17 F11 08 03 2012 8 27 LF 10 24 59 Today TfF5 45 2012 7 17 410 16 23 Today F F5 28 2012 7 17 F 2 21 30 Keychain login login login login login login login login 3 Double click the SSID of your network and you will see the followi
100. right Click Refresh in the drop down menu to refresh the list of available MAC addresses If the address you wish to add is not listed enter it manually Enter a MAC address of computer or network device manually without dashes or colons e g for MAC address aa bb cc dd ee ff enter aabbccddeeff Enter a comment for reference identification consisting of up to 16 alphanumerical characters Add Click Add to add the MAC address to the MAC address filtering table MAC address entries will be listed in the table as shown below Select an entry using the Select checkbox 00 1b 63 cb 4c b5 MACBOOK 4 29BA 192 168 2 101 Ia Delete Selected Delete All Delete Selected Delete selected or all entries from the table Delete All lll 3 4 5 Schedule The schedule feature allows you to automate the wireless radio to switch on off at specified times Multiple schedules can be configured Check uncheck the box Enable Schedule Settings to enable disable the wireless on off scheduling function A The EW 7208APC must remain connected to the Internet and use an NTP server for the schedule feature to function correctly Wireless Schedule Enable Schedule Settings 1 Weekday Fl su nday EJ Monday Tuesday EJ Wednesday EJ Thursday E Friday Fl satu rday 2 Time Hour O o Minute 00 fi 3 Command Wireless On Add TETE Monday Tuesday Wednesday Thursday Friday 01 00 wireless off Monday Tuesday Wednesda
101. ription Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks 1 item 1 item selected 2 55 PM A B 0 73 2012 7 Select Obtain an IP address automatically and Obtain DNS server address automatically should be selected Network View Network v v Search Network Network discovery and file sharina are turned off Network computers and devices are not visible Click to chanae ES Network and Sharing Center Favorites 4e Network Connections BE Desktop Je Downloads T E Network and Internet Network Connections vw Search Network Connections JO S Recent places MOrnaniza w Micahle thir nehwark danca Nisannce thir goppection Rename this connection gt amp v Ll 3 Libraries Ethernet Properties ES Documents A Music E Pictures B Videos General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator Computer for the appropriate IP settings i Network Obtain an IP address automatically Use the following IP address Subnet mask Default gateway Alternate DNS server Validate settings upon exit 2 55 PM 12 3 2012 IV 1 1 5 MacOS 1 Have your Macintosh computer
102. rmat you selected above A complex hard to guess key is recommended Check the Hide box to hide your password from being displayed on screen 111 3 4 1 4 WPA Radius WPA RADIUS is a combination of WPA encryption and RADIUS user authentication If you have a RADIUS authentication server you can authenticate the identity of every wireless client against a user database Wireless Security Encryption WPA RADIUS WPA Unicast Cipher Suite amp WPA TKIP WPA2 AES WPA Mixed RADIUS Server IP address RADIUS Server Part 1812 RADIUS Server Password WPA Unicast Select from WPA TKIP WPA2 AES or WPA2 Cipher Suite Mixed WPA2 AES is safer than WPA TKIP but not supported by all wireless clients Please make sure your wireless client supports your selection WPA2 AES is recommended followed by WPA2 Mixed if your client does not support WPA2 AES RADIUS Server IP Input the IP address of the RADIUS address authentication server here RADIUS Server Port Input the port number of the RADIUS authentication server here The default value is 1812 RADIUS Server Input the password of the RADIUS Password authentication server here Ill 3 4 2 Multiple SSID The EW 7208APC supports up to four additional SSIDs for each wireless band in access point mode Once configured these SSIDs are displayed in the Multiple SSID Status table as shown below Use the Multiple SSID Basic Settings box to configure additional
103. rts inside the device If you experience problems with the device please contact your dealer of purchase and ask for help The device is an electrical device and as such if it becomes wet for any reason do not attempt to touch it without switching the power supply off Contact an experienced electrical technician for further help Il Installation 5GHz 1 Screw in the included antennas to 24GHz i 2 4GHz the back of the EW 7208APC taking care to attach the two 2 4GHz antennas to the outside and the 5GHz antenna to the center Each antenna is labeled on the base with 2 4GHz or 5GHZ 2 Plug the included power adapter into the device s DC power port and the other end into an electrical socket FF 5 88 3 2 1 Item O gt 4 y EA 3 Ensure that the Wi Fi On Off switch is set to on and that three LEDs power 2 4GHz 5GHz Wi Fi display on CU amp 2 4G 5G 4 Usea Wi Fi device e g computer tablet smartphone to search for a Wi Fi network with the SSID edimax setup or edimax setup5G and connect to it a SOS 4 or Android 4 and above are required for setup on a A smartphone or tablet 5 Open a web browser and if you do not automatically arrive at the Get Started screen shown below enter the URL http edimax setup and click Get Started to begin the set
104. s all settings will be reset Default settings are displayed on the product label on the bottom of the device as shown below Fe 9C D E E MAUTU O TO 3 CB00010 MADE IN CHINA V1 0A TS MAC 801F02BB977F PIN CODE 58484470 i d AP Login Enter this URL in a web browser to run iQ Setup or configure advanced settings You must be connected to the device by Wi Fi or Ethernet cable Username Password This is the default username and password to access the browser based configuration interface when you go to the AP Login URL above Wi Fi Network This is the default Wi Fi network name for the Name device Search for this name SSID and connect to itin order to access the Router Login URL above A MAC address is unique to every device and is used for identification within a network Your device s unique MAC address is displayed here PIN CODE This is your device s PIN code for Wi Fi Protected Setup WPS 8 forgot my password a Reset the router to its factory default settings and use the default username admin and default password 1234 Default settings are displayed on the product label on the bottom of the device as shown above 9 My EW 7208APC has a weak wireless signal Weak signals are usually caused by interference from other devices or obstacles blocking the EW 7208APC s wireless signal a Keep the device away from other radio devices such as microwaves or cordless phones b Do n
105. s Isolation Channel Number Site Survey a Wireless Clients Disable Wireless Check the box to disable the wireless function of your device Keep the default AP value for the device to act as a standard wireless access point or select AP Bridge WDS for the device to function in WDS mode see below Displays the wireless standard used for the EW 7208APC s 2 4GHz b g n means that 802 11b 802 11g and 802 11n wireless clients can connect to the EW 7208APC Wireless Network This is the name of your Wi Fi network for Name SSID identification also sometimes referred to as SSID The SSID can consist of any combination of up to 32 alphanumerical characters Broadcast SSID Enable or disable SSID broadcast When enabled the SSID will be visible to clients as an available Wi Fi network When disabled the SSID will not be visible as an available Wi Fi network to clients clients must manually enter the SSID in order to connect A hidden disabled SSID is typically more secure than a visible enabled SSID Enable Wireless Clients Isolation Channel Number Site Survey Wireless Clients Check the box to enable wireless clients isolation This prevents wireless clients connected to the EW 7208APC from communicating with each other and improves security Typically this function is useful for corporate environments or public hot spots and can prevent brute force attacks on clients usernames an
106. s page You can enable the router to dynamically allocate IP addresses to your LAN clients and you can modify the IP address of the device The device s default IP address is 192 168 2 1 A You can access the browser based configuration interface using gt the device s IP address instead of using the URL http edimax setup LAN IP IP Address Subnet Mask 802 1d Spanning Tree DHCP Server Lease Time IP Address Specify the IP address here This IP address will be assigned to the EW 7208APC and will replace the default IP address Specify a subnet mask The default value is 255 255 255 0 802 1d Spanning Select Enable or Disable to enable disable Tree 802 1d Spanning Tree This creates a tree of connected layer 2 bridges typically Ethernet switches within a mesh network and disables those links that are not part of the tree leaving a single active path between any two network nodes Lease Time Select a lease time for the DHCP leases here The DHCP client will obtain a new IP address after the period expires Your device s DHCP server automatically assigns IP addresses to computers on its network between a defined range of numbers DHCP Server Start IP 197 168 272 100 End IP 192 168 2 200 PORE Enter the start IP address for the DHCP server s IP address leases LL Enter the end IP address for the DHCP server s IP address leases Your device s DHCP server can be configured to assign static fixed
107. s will not be changed To restart click on the APPLY button below You will be asked ta confirm your decision The restart will be complete when the Internet LED light stops blinking Apply 111 4 9 7 Logs You can view the system log and security log here Use the drop down menu in the top right corner to select which log to view System Log Jan 1 00 00 08 none syslog info syslogd started BusyBox v1 11 1 Mar 13 07 34 44 none user debug syslog Debu buildIfvc Interface lo Addr 127 0 0 1 Flags 0 Mar 13 07 34 44 none user debug syslog Debu buildlfVc Interface eth1 Addr 192 168 10 143 Mar 13 07 34 44 none user debug syslog Debu buildifVc Interface brO Addr 182 168 2 1 Flag Mar 13 07 34 44 none user notice syslog Note adding VIF idx 0 Fl flags OxO IP 192 168 2 1 b Mar 13 07 34 44 none user notice syslog Note adding VIF idx 1 Fl flags 0x0 IP 2192 168 10 14 4 n E E UN Security Log 1970 01 01 00 00 22 start Dynamic IP 1970 01 01 00 00 24 SNTP connect to TimeServer 59 124 196 84 Tr 2014 03 13 07 34 33 SNTP connect success 2014 03 13 07 34 33 SNTP set time to 2014 03 13 07 34 33 2014 03 13 07 34 34 Firewall WAN1 IP is 192 168 10 143 2014 03 13 07 34 34 Firewall WAN IP is 0 0 0 0 2014 03 13 07 34 34 Firewall WANS IP is 0 0 0 0 2014 03 13 07 34 34 Firewall setting firewall 2014 03 13 07 34 36 SNTP connect to TimeServer 59 124 196 84
108. sable C Disable Enable Basic Settings Site Suvey 2 4 Osc RST Channel Number Security Setting Encryption WPA2 W Security Type amp AES Pre shared Key Format Passphrase bal Pre shared Key abcd1234 Save Settings Enable Disable Enable or disable your WISP connection The name of the WISP network which your EW 7208APC is connected to Manually enter an SSID if you wish or use Site Survey below Site Survey Select wireless frequency and click Site Survey List to open a new window and select your WISP network Security Setting Please refer to III 3 5 1 Basic for a description of security settings Ill 4 3 1 WAN Setup Select a Wide Area Network WAN connection mode and configure the settings If you are unsure about your connection type contact your ISP A In WISP mode only Dynamic IP Static IP amp PPPoE are available for WAN Connection Mode WAN Connection Mode Connection Mode Dynamic IP 7 Dynamic IP Dynamic IP Host Name 111 4 3 1 1 Dynamic IP Select Dynamic IP If your Internet service provider assigns IP address automatically using DHCP Dynamic Host Configuration Protocol Dynamic IP MAC Address 8 Obtain an IP address automatically DNS Address x t Use the following IP address DNS1 Address 0 0 0 0 DMS2 Address 0 0 0 0 DNSS Address 0 0 0 0 MTU 512 MTU Value lt 1500 TTL amp Disable L Enable Save Settings HostName X Enterthe host name of
109. se enter the MAC address here If you are connecting the router to a computer press Clone Mac to automatically enter your computer s MAC address ISP here MTU Enter the maximum transmission unit MTU value of your network connection The default value is 1500 TTL Enable Disable time to live TTL function which limits the lifespan of network data to improve performance 111 4 3 1 3 PPPoE Select PPPoE if your ISP is providing you Internet access via PPPoE Point to Point Protocol over Ethernet PPPoE MAC Address 8 Obtain an IP address automatically DNS Address v i Use the following IP address DNS1 Address 0 0 0 0 DNS Address 0 0 0 0 DNS3 Address 0 0 0 0 TTL Disable Enable MTU 512 lt MTU Value lt 1492 Connection Type _ Connect Disconnect Idle Time Qut 10 1 1000 minutes C Enable Dual Wan Access IGMP Source Sa ppp Enter the user name assigned by your ISP here Enter the password assigned by your ISP here MAC Address For some applications you may need to designate a specific MAC address for the router Please enter the MAC address here If you are connecting the router to a computer press Clone Mac to automatically enter your computer s MAC address DNS Address Select Obtain an IP address automatically or Use the following IP address Check with your ISP if you are unsure DNS Address 1 2 amp 3 Enter the DNS address es assigned by your ISP
110. se functions 5GHz Wireless Wireless Module Enable Fragment Threshold 2346 256 2346 RTS Threshold 2347 0 2347 Beacon Interval 100 20 1024 ms DTIM Period 3 1 10 Data Rate Auto I N Data Rate Auto Channel Width 9 20 40 80 MHZ 20 40 MHZ 20 MHZ Preamble Type 9 Short Preamble Long Preamble CTS Protect Auto Always Y None Tx Power 100 i WMM 9 Auto Set the Fragment threshold of the wireless radio The default value is 2346 Set the RTS threshold of the wireless radio The default value is 2347 Set the beacon interval of the wireless radio The default value is 100 Set the DTIM period of wireless radio The default value is 3 Set the wireless data transfer rate The default is set to Auto Set the data rate of 802 11n The default is set to Auto Channel Width Select wireless channel width bandwidth used by wireless signals from the device the recommended value is 20 40 80MHz Preamble Type CTS Protect Set the wireless radio preamble type The default value is Short Preamble Enabling this setting will reduce the chance of radio signal collisions between 802 11b and 802 11g wireless access points It s recommended to set this option to Auto Set the power output of the wireless radio You may not require 10096 output power Setting a lower power output can enhance security since potentially malicious unknown users in distant areas will not be able to access your signal WMM Wi
111. ss Enter a starting IP address in the left field and the end IP address in the right field to define a range of IP addresses or enter an IP address in the left field only to define a single IP address Various services are listed here with a short description Check uncheck the box for each service you wish to select Protocol Select protocol TCP or UDP or Both for a service not included in the Client PC Service list Port Range Enter the port range for the service not included in the Client PC Service list Enter a single port number e g 110 a range of port numbers e g 110 120 or multiple port numbers separated by a comma e g 110 115 120 Click Add to add selected services or a user defined service to the IP filtering table IP filtering entries will be listed in the IP filtering table shown below Enable IP Filtering Table e Deny amp Allow IP Filtering Table Client PC Client PC IP e E Description Address Client Service WWW E mail Sending News Forums E mail Receivin 1 Laptop 192 168 2 101 z a duci E Secure HTTP File Transfer Add PC Delete Selected Delete All Delete Selected Delete selected or all entries from the table Delete All Ill A 6 3 DMZ A Demilitarized Zone DMZ is an isolated area in your local network where private IP addresses are mapped to specified Internet IP addresses allowing unrestricted access to the private IP addresses but not to the wider loca
112. stant responses for better performance I11 3 5 2 5GHz Wireless These settings are for experienced users only Please do not change any of the values on this page unless you are already familiar with these functions 5GHz Wireless Wireless Module Enable Fragment Threshold 2346 256 2346 RTS Threshold 2347 0 2347 Beacon Interval 100 20 1024 ms DTIM Period 3 1 10 Data Rate Auto I N Data Rate Auto Channel Width 9 20 40 80 MHZ 20 40 MHZ 20 MHZ Preamble Type 9 Short Preamble Long Preamble CTS Protect Auto Always Y None Tx Power 100 i WMM 9 Auto Set the Fragment threshold of the wireless radio The default value is 2346 Set the RTS threshold of the wireless radio The default value is 2347 Set the beacon interval of the wireless radio The default value is 100 Set the DTIM period of wireless radio The default value is 3 Set the wireless data transfer rate The default is set to Auto Set the data rate of 802 11n The default is set to Auto Channel Width Select wireless channel width bandwidth used by wireless signals from the device the recommended value is 20 40 80MHz Preamble Type CTS Protect Set the wireless radio preamble type The default value is Short Preamble Enabling this setting will reduce the chance of radio signal collisions between 802 11b and 802 11g wireless access points It s recommended to set this option to Auto Set the power output of the wirel
113. subnet mask default gateway and DNS server addresses IP address 192 168 2 10 Subnet Mask 255 255 255 0 Preferred DNS Server 192 168 2 1 Click OK when finished IV 1 2 3 Windows 7 1 Click the Start button it should be located in the lower left corner of your computer then click Control Panel LD JE E l Getting Started E Windows Media Center a S Calculator m Sticky Notes EA Snipping Tool Ey Paint a Remote Desktop Connection E Magnifier a e Solitaire gt All Programs Search programs and files Control Panel Adjust your computer s settings System and Security Review your computer s status Back up your computer Find and fix problems Network and Internet View network status and tasks Choose homegroup and sharing option View devices and printers Add a device Programs Uninstall a program 3 Click Local Area Connection Edimax Documents Pictures Music Games Computer Control Panel Devices and Printers Default Programs Help and Support Shut down aie View by Category Y User Accounts and Family Safety ay Add or remove user accounts iy Set up parental controls for any user Appearance and Personalization Change the theme Change desktop background Adjust screen resolution Clock Language and Region Change keyboards or other input methods Change display language Ease of Access Let Windows suggest s
114. support WPA2 AES Pre shared Key Choose from Passphrase 8 63 Format alphanumeric characters or Hex up to 64 characters from 0 9 a f and A F Pre shared Key Please enter a key according to the format you selected above A complex hard to guess key is recommended Check the Hide box to hide your password from being displayed on screen 111 4 5 1 4 WPA Radius WPA RADIUS is a combination of WPA encryption and RADIUS user authentication If you have a RADIUS authentication server you can authenticate the identity of every wireless client against a user database Wireless Security Encryption WPA RADIUS WPA Unicast Cipher Suite amp WPA TKIP WPA2 AES WPA Mixed RADIUS Server IP address RADIUS Server Part 1812 RADIUS Server Password WPA Unicast Select from WPA TKIP WPA2 AES or WPA2 Cipher Suite Mixed WPA2 AES is safer than WPA TKIP but not supported by all wireless clients Please make sure your wireless client supports your selection WPA2 AES is recommended followed by WPA2 Mixed if your client does not support WPA2 AES RADIUS Server IP Input the IP address of the RADIUS address authentication server here RADIUS Server Port Input the port number of the RADIUS authentication server here The default value is 1812 RADIUS Server Input the password of the RADIUS Password authentication server here 111 4 5 2 Guest You can setup an additional Guest Wi Fi network so guest users
115. t to display a new window showing information about the surrounding wireless environment This information is useful to select an effective wireless channel number Click Show List to display a new window showing information about wireless clients Please disable any pop up blockers if you have difficulty using this function AP Bridge WDS Mode AP Bridge WDS m AP AP Bridge WDS Band Wireless Distribution System WDS can bridge repeat access points together in an extended network WDS settings can be configured as shown below 7 N When using WDS configure the IP address of each access point to be in the same subnet and ensure there is only one active DHCP server among connected access points preferably on the WAN side WDS must be configured on each access point using correct MAC addresses All access points should use the same wireless channel i MAC Address MAC Address 2 MAC Address 4 Set Security Set Security MAC Address 1 4 Enter the correct MAC address for other access points in WDS mode Set Security Click Set Security to open a new window and enter the security settings for WDS shown below Click Save when finished A Please ensure you setup and save wireless security settings before EE you click Set Security to set WDS security settings AP Bridge WDS Security Setting Encryption WPA Pre shared Key WPA Unicast Cipher Suite amp WPA AES Pre
116. tatus Internet Model Wireless Router IF Address 192 168 2 1 Setup Wizard Current Time 2014 3 3 7 15 45 Subnet Mask 255 255 255 0 LAN fI Hardware Version Rev A DHCP Server Enable 2 46Hz Wireless Firmware Version LOS MAC Address OO EO 4C 81 96 C1 5GHz Wireless Firewall IP Address Mode Dynamic IP Connect Mode AP Qos E IP Address 192 168 77 110 ESSID edimax 2 4G 8196D1 Advanced Subnet Mask 255 255 255 0 Channel Number 1 E i Default Gateway Address 192 168 77 1 Security WPA2 AES Administration MAC Address OO ED 4C 81 96 C9 MAC Address OO EO 4C 81 96 D1 Primary DNS 192 168 77 1 Secondary DNS 5GHz Wireless Third DNS Mode AP ESSID edimax 5G B196C1 Channel Number 157 Security WPA AES MAC Address O0 60 40 81 06 01 Ill 4 2 Setup Wizard You can run the setup wizard again to reconfigure the Setup Wizard basic settings of the device or you can run a wizard to help you switch the device to a different operating mode Select Setup Wizard or Switch to Router Access Point Range Extender Wireless Bridge WISP mode and then click Run Wizard to begin Setup Wizard Setup Wizard This setup wizard is an intelligent and easy tool for you to complete the basic settings of the device quickly Switch to Router Access Point Range Extender Wireless Bridge WISP mode This setup wizard will guide you ta switch the device to another mode Setup Wizard This wi
117. this IP address subnet mask default gateway and DNS server addresses IP address 192 168 2 10 Subnet Mask 255 255 255 0 Preferred DNS Server 192 168 2 1 Click OK when finished IV 1 2 5 Mac l Have your Macintosh computer operate as usual and click on System Preferences System Preferences 2 In System Preferences click on Network Internet amp Network l s Taa C MobileMe Network QuickTi me Sharing 3 Click on Wi Fi in the left panel and then click Advanced in the lower right corner eoo Network 4 gt ShowAll Location Automatic Status Connected Turn Wi Fi Off Ene Wi Fi is connected to OBM AirPort 2 4G and e Ethernet ooo has the IP address 192 168 77 119 a iniri Qe Network Name OBM AirPort 2 4G V Ask to join new networks Known networks will be joined automatically If no known networks are available you will e FireWire be asked before joining a new network 802 11 n WLAN e G0 e Bluetooth ius V Show Wi Fi status in menu bar Advanced Y mv fi id Click the lock to prevent further changes Assist me Revert Apply 4 Select TCP IP from the top menu and select Manually from the drop down menu labeled Configure IPv4 then click OK Network Using DHCP Wi Fi iri Using DHCP with manual address pxies Hardware Using BootP i TA Manually IPv4 Addre Off S
118. tive DHCP Elentir 139 SEU E 139 IV APDO Equina AO Configuring vour IP address iii A A 140 How to check that your computer uses a dynamic IP address 141 WY NIAC OWS PLE 141 WINING OWS VIS ti A oom 143 aaro 145 VA INTe ol da m OT TO TD UT 148 Mar GL dC A AS 152 How to modify the IP address of your computer cccccesecccesscceeeseeceeeeceeaeeceeeeaees 154 Windows dO H 154 WINS VISA sas 156 WIDngOWS Tari aces areal a ae ae 157 WO OWS cu sched ae 160 MAC ere M M 164 How to Find Your Network Security Key uode A eie eeu ap bere 167 Windows Z UV UST elite deine sn a alee di sale atts le dains te beue cles ciet adc rer ip aus iltud use 167 jul tem ted ere ean torsos ore cut cid 169 How to Find Your Router s IP AddresS oocccccoccnnonocononnccnnonacononacononanonnonacononarononanos 172 WIndows XP VISA AT T m 172 WANING OW SO NER NRI T I m 174 IV AG me 177 Connecting to a WI FLDeDWOEFIK 5 send iri p e o E ua ve co av E DX ONERE RU EE Us 179 TOUS E 181 NECI LIC RUNTIME LOT Product Information l 1 Package Contents Before you start using this product please check if there is anything missing in the package and contact your dealer to claim the missing item s Ethernet Cable Quick Installation Guide Power Adapter l 2
119. tivity em transferring receiving data off GS o 2 4GHz Wi Fi wireless activity 2 4GHz WI FI transferring receiving data Blue Flashing 5GHz WPS is active Of 5GHz Wi Fi not active can t access the Internet Ensure that all cables are connected properly Try a different Ethernet cable Check if you can access the web based configuration interface If not please ensure your Wi Fi device is set to use a dynamic IP address If you are unsure how to do this try using a computer and refer to IV Appendix for guidance Login to the web based configuration interface and go to Internet WAN Setup and check that the connection type is correct If you are unsure which internet connection type you have please contact your Internet Service Provider ISP Connect a computer directly to your modem and check if you can access the internet If you can t please contact your Internet service provider for assistance can t open the web based configuration interface Please ensure your Wi Fi device is set to use a dynamic IP address If you are unsure how to do this try using a computer and refer to IV Appendix for guidance 7 How do reset my device to factory default settings a To reset the device back to its factory default settings press and hold the WPS Reset button for over 10 seconds until the white power LED begins to flash Please wait a few minutes for the product to restart When the device restart
120. u keep the default settings DoS El Pin g of Death 5 Ping of Death Packet S Per Second Burst 5 Fl Discard Ping From WAN NMAP FIN SURG PSH Xmas tree Another Xmas tree Fl Port Scan Null scan SYN RST SYN FIN SYN only unreachable ports E Sync Flood 30 Packet S Per Second Burst 30 Save Settings Ping of Death Specify the frequency of ping of death packets which will trigger the router s DoS protection function Discard Ping from Check this box and the router will not answer WAN ping requests from the Internet Intruders use port scanners to detect open Internet IP address ports Check each type of port scan to prevent Sync Flood Specify the frequency of sync flood packets which will trigger the DoS protection function 111 4 7 QoS Quality of Service QoS is a feature to manage Internet bandwidth efficiently Some applications require more bandwidth than others to function properly and QoS allows you to ensure that sufficient bandwidth is available Minimum or maximum bandwidth can be guaranteed for a specified application A QoS can improve the EW 7208APC s performance QoS is recommended to optimize performance for online gaming Ill 4 7 1 QoS Check uncheck the box Enable QoS to enable disable the QoS function Click Add to open a new window and setup a QoS rule The Current QoS Table displays all QoS rules QoS El Enable Qos Total Download Bandwidth 0 kbits
121. ubnet Mask 255 255 255 0 Router 192 168 77 1 Configure IPv6 Automatically Router IPv6 Address Prefix Length A Your existing static IP address will be displayed in the IP gt address field before you replace it Please make a note of this IP address subnet mask default gateway and DNS server addresses 5 Inthe IPv4 Address and Subnet Mask field enter IP address 192 168 2 10 and subnet mask 255 255 255 0 Click on OK Network DNS WINS 802 1X Proxies Hardware Subnet Mask 255 255 255 0 Router 192 168 10 254 Configure IPv6 Automatically Router IPv6 Address Prefix Length Cancel 6 Click Apply to save the changes a E QoE Location Location 5 2 13 2 54 PM a Wi Fi E EE E Wi Fi is connected to EdimaxAP20 and has e Ethernet the IP address 192 168 2 10 Not Connected y 902 11 dapter Qe Network Name EdimaxAP20 Not Connected 802 11 apter 2 Ask to join new networks Not Connected Known networks will be joined automatically n 4 If no known networks are available you will FireWire sy have to manually select a network Not Connected x ru V Show Wi Fi status in menu bar Advanced 2 id Click the lock to prevent further changes Assistme Revert Apply p IV 1 3 How to Find Your Network Security Key To find your network security key please follow t
122. ue is 1392 Check the Enable box if you are using BEZEQ network services Israel users only Connection Type Specify a connection type Continuous Connected all the time Connect on Demand Connect when you initiate an Internet connection Manual Connect disconnect manually using the Connect and Disconnect buttons Idle Time Out Specify the amount of time the router waits before shutting down an idle connection Only available when Connect on Demand above is selected 111 4 3 1 5 L2TP Select L2TP if your ISP is providing you Internet access via L2TP Layer 2 Tunneling Protocol L2TP Obtain an IP address automatically Host Name MAC Address Use the following IP address Static IP Address Subnet Mask Default Gateway Address MAC Address DNS Address DNS1 Address DNS Address DMS3 Address L Enable Dual Wan Access IGMP Source LITP Settings User ID Password L2TP Gateway MTU Connection Type Idle Time Out 000000000000 Clone MAC 0 0 0 0 0 0 0 0 0 0 0 0 000000000000 8 Obtain an IP address automatically CO Use the following IP address 0 0 0 0 0 0 0 0 0 0 0 0 Sera O PPP 0 0 0 0 1392 512 lt MTU Value lt 1492 connect Disconnest 10 1 1000 minutes Enter the host name of your computer here If required MAC Address For some applications you may need to designate a specific MAC address for the router Please enter
123. up Restore Upgrade Restart Logs Active DHCP Client Statistics 11 4 9 1 Time Zone Time Zone Set Time Zone GMT Greenwich Mean Time Dublin Edinburgh Lisbon London A Time Server Address pool ntp org Enable Function January 1 To January 1 Daylight Savings Save Settings Set Time Zone Select the time zone of your country or region Time Server Address The travel router supports NTP Network Time Protocol for automatic time and date setup Input the host name of the IP server manually Daylight Saving If your country region uses daylight saving time please check the Enable Function box and select the start and end date lll A 9 2 Password You can change the password used to login to the browser based configuration interface here It is advised to do so for security purposes Please make a note of the new password In the event that you forget the password and are unable to login to the browser A based configuration interface see Il 7 Reset to factory default settings for how to reset the device Password Current Password New Password Confirmed Password Current Password Enter your current password Enter your new password Confirmed Password Confirm your new password 111 4 9 3 Remote Access Check Enabled to enable the remote access feature and then enter the appropriate values Remote Access Host IP Address Port Enabled Save Settings Host IP A
124. up process EDIMAX AC750 Multi Function Dual Band Wi Fi Access Point EW 7 208APC English v Get Started If you cannot access http edimax setup please make sure your A Wi Fi device is set to use a dynamic IP address This is a simple procedure and step by step instructions to do this on a computer can be found in IV Appendix 6 Choose if you want to use your EW 7208APC in its default access point mode or in a different mode w EDIMAX Access Point The default mode of this product is Wi Fi access point mode It connects to your router via Ethernet cable and provides Internet access for your computers smartphones tablets and any other network devices CHANGE TO A DIFFERENT MODE YES NEED A Wi Fi ACCESS POINT The EW 7208APC s five available modes are outlined below Access Point Mode The device connects to an existing router via Ethernet cable and provides 2 4GHz and or 5GHz Internet wireless and Ethernet access for your network devices Range Extender The device connects wirelessly to your existing Mode 2 4GHz and or 5GHz network and repeats the wireless signal s Wireless Bridge Mode The device connects to a network device for example TV gaming console or media player via Ethernet cable and acts as a wireless receiver allowing the network device to join your Wi Fi network Wi Fi Router Mode The device connects to your modem and provides 2 4GHz and or 5GHz Internet
125. ure the safe use of the equipment EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria Belgium Bulgaria Cyprus Czech Denmark Estonia Finland France Germany Greece Hungary Ireland Italy Latvia Lithuania Luxembourg Malta Netherlands Poland Portugal Romania Slovakia Slovenia Spain Sweden Turkey and United Kingdom The ETSI version of this device is also authorized for use in EFTA member states Iceland Liechtenstein Norway and Switzerland EU Countries Not Intended for Use None EU Declaration of Conformity English Francais CeStina Polski Romana Pycckun Magyar Turkce VkpalHcbKa SlovenCina Deutsch Espa ol Italiano Nederlands Portugu s Norsk Svenska Dansk Suomi This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC 2009 125 EC Cet quipement est conforme aux exigences essentielles et autres dispositions de la directive 1999 5 CE 2009 125 CE Toto zarizeni je v souladu se z kladn mi pozadavky a ostatnimi prislusnymi ustanoven mi sm rnic 1999 5 ES 2009 125 ES Urzadzenie jest zgodne z og lnymi wymaganiami oraz szczeg lnymi warunkami okreslonymi Dyrektywa UE 1999 5 EC 2009 125 EC Acest echipament este n conformitate cu cerin ele esen iale si alte prevederi relevante ale Directivei 1999 5 CE 2009 125 CE 3ro o6opynoBaHMe COOTBeTCTByeT
126. will connect to the 5GHz network If there is no 5GHz network available the network device will connect to the 2 4GHz network instead 3 In range extender mode how do connect to a network which has a hidden SSID a During iQ Setup you can manually enter a SSID in the Wi Fi network name field as shown below for either both 2 4GHz and 5GHz along with the relevant encryption information ED MAX Range Extender 2 4GHz Wireless Site Survey Please set a new Wi Fi network name SSID for the range extender if you wish and set the security key for your existing wireless network if required Wi Fi network name SSID Range extender SSID Encryption Disable v Wi Fi network name Enter the SSID network name of your existing hidden network Range extender SSID Enter an SSID for the EW 7208APC or leave it blank to use a default which consists of your existing router s SSID above 2EX Encryption Select and enter the encryption information for your existing hidden network 4 What do the LEDs mean The LEDs can be identified by icons on the underside of the EW 7208APC eee FL _ _ LSE AT A a Ja mo amp 2 4G 5G White Internet connection is ready Internet Blue Factory default state or Ethernet E Flashing cable not connected or no Internet connection Flashing 2 4GHz WPS is active 2 4GHz Wi Fi not active On E On 5GHz Wi Fi wireless ac
127. y Thursday Friday 08 00 wireless on Delete Selected Delete All Save Settings Settings have been saved Please click here to restart the router and bring the new settings into effect Wireless scheduling can save energy and increase the security of your network PY 1 Usethe checkboxes to select which day s to include in the schedule 2 Specify a time hour and minute for the schedule using the drop down menu 3 Select which command applies to this schedule from the drop down menu either Wireless On or Wireless Off Add the schedule to the table of active schedules Active schedules will be displayed in the table as shown below Select an entry using the Select checkbox ar Monday Tuesday Wednesday Thursday Friday 01 00 wireless off Monday Tuesday Wednesday Thursday Friday 08 00 wireless on Delete Selected Delete All Save Settings Settings have been saved Please click here to restart the router and bring the new settings into effect Delete Selected Delete selected or all entries from the table Delete All 111 3 5 Advanced Advanced Advanced features of the EW 7208APC can be 2 4GHz Wireless configured from the Advanced menu 5GHz Wireless 111 3 5 1 2 4GHz Wireless These settings are for experienced users only Please do not change any of the values on this page unless you are already familiar with these functions 2 4GHz Wireless Wireless Module Enable Fragme
128. zard will help you to set up the basic functions and settings of the device For guidance about using the setup wizard please refer to Il Installation Switch to Router Access This wizard will help you to switch the device Point Range Extender to a different operating mode Wi Fi router Wireless Bridge WISP mode access point mode range extender mode wireless bridge or WISP mode see below Switch to Router Access Point Range Extender Wireless Bridge WISP mode 4 Follow the on screen instructions to back up your current settings and then reset the device back to its factory default settings D After the device has reset you Will see the screen below Close your browser and open it again Reset to Default E You have successfully reset the device to factory defaults Please close the browser and open it again This device will start running the setup wizard for you to switch the mode 6 Follow the on screen wizard to setup your device in a different mode Refer to Il Installation Step 3 onwards for help if needed A If you don t see the Get Started screen try reconnecting to the gt edimax setup SSID and go to http edimax setup in a web browser 111 4 3 Internet WISP The Internet menu provides access to WAN and DDNS settings Click on an item from the submenu to view and or configure the settings WAN Setup DDNS A In WISP mode the screen below will be displayed WISP Enable Di

EW-7208APC User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents