RACK-814 CHASSIS USER'S MANUAL
Contents
1. 41015 0032XX INTERFACE CARD BRACKET 32100 000229 WIRE CABLE FAN 31100 000024 FA m m 2 Wire 3 41008 0047XX UPPER CO VER FA 3 8 E 1009 0002XX GRII 6002 000200 D PC 14 OPTION 1020 0019XX 5003 000303 PID jp OnE BN 2 22. RACK 814 CHASSIS USER S MANUAL Copyright Notice This document and product is copyrighted April 2000 by ICP Electronics Inc All rights are reserved No part of this manual may be reproduced copied or translated without prior notice to ICP Electronics Inc The information provided in this document is for reference only We do not assume any responsibility arising out of the application of the products This manual is subject to change without any notice Rack 814 ICP are trademark of ICP Electronics Inc Table of Contents Chapter 1 Product Information 1 1 General Information 1 2 Product Specifications 1 3 Dimensions Chapter 2 System Setup 2 1 The Front Panel of Rack 814 2 2 Removing the chassis cover 2 3 Disk Drives Installation 2 4 Replacing the Filter 2 5 The Card Clamp amp Backplane Installation 2 6 Power Supply Installation 2 7 Fan Installation Appendix A Passive Backplane Appendix B Exploded Diagram Chapter 1 Product Information 1 1 General Information Rack 814 is a PC AT compatible computer designed for Industrial applications It is a steel rugged chassis specially designed to work under harsh environment for high reliability application The Rack 814 features 14 slots Passive Backplanes and high reliability AC DC Input Power Supply Options available are ACE 920A ACE 932A ACE932T ACE925T ACE925C ACE 916V ACE 935A and ACE C232 Specially equipped with Keyboard Port on front side for eas
3. anes inside the chassis and screw it Figure below illustrates how to install the backplanes on the Rack 814 2 6 Power Supply Installation ation ACE 920A 932A 935A1 9257 2 6 1Power Supply for the Rack 814 install SCREWx2 2 6 2Redundant Power Supply for the Rack 814 installation ACE C232C SCREWx2 2 7 Fan Installation SCREWx4 Removable cooling fan By two spring screw PASSIVE BACKPLANES APPENDIX A ev LLE v9 667 ee 9h7 21 6h7 3 2 3 1 L6 LLE PCI2 PCIA v1821 NASA TS A A LAADA abana ETTET TN CUTE v9 0vL 901 KAKA A NES LITE SET LIT PRAAIPPUAABPRUAABPUAADPIUAAPIRA PUKADERU KADI R K SIDE COLLECTE ECO CCE CCC CC ECTS AMADO CAN RACIAADORAARCOFAADACIAR MAROSAAADOAARD ER 0L S6 KKSTYT YTY STTYT STT YTY arado TE ATT MODEL PX 14S VER E lt p AAA HUSAADUUAADHURAADUS PUVAASPUVAAPUUMAAN PRUASDS UAM ALADO MARA AOSTA nidad 00 0 175 39 255 58 264 39 2 S c E n Black Blue White BROWN 14 APPENDIX B EXPLODED DIAGRAM PARTLIST ITEM PARTNO DESCRIPTION O TY REMARK 1001 0029XX ASSEMBLY FRONT PANEL 1012 0025XX 5007 000104 LOCK 32000 000091 USB CAB 131LP01 00 010 LP 01 PA 5002 000103 CKE 1BP14S 00 000 14S Bcak plane OPTION 41013 001502 PCB BASE 41006 0075XX ASSEMBLE BASE
4. nsions 500 4 Chapter 2 Installation Procedure The following set up procedures are provided to assist you in installing the system unit please follow the steps below 2 1 The Front Panel of Rack 814 H POW ESET BU KEYBOARD POWER SWITCH 2 2 Removing the chassis cover The cover is mounted by 6 screws at each side and the top of the chassis remove them and slide the cover to the rear of the chassis Figure below shows how to remove the chassis cover 2 3 Disk Drives installation 1 Open the disk drive door in the front panel 2 Remove the disk drive bay 3 Attach the FDD to the bracket with four screws and connect FDD cable amp power cable to the FDD 4 Attach the HDD to the bracket with four screws and connect a 40 pin flat cable amp power cable to the HDD 2 4 Replacing the Filter The filter of the Rack 814 is located at the front end of the chassis The filter should be removed and cleaned at least once a month to achieve optimum performance The filter can be removed simply by turn the key lock to the counter clock wise direction Take out the old filter replace it with the new one if its already worn out Then close and lock the filter door 2 5 The Backplane Card Clamp Installation To install the backplanes in the chassis remove the clamp panel first then put the backpl
5. y access Rack 814 will withstand shock vibration dust and wide range of temperature in Industrial environments A lockable door protects drives and switches from unauthorized misuse and particle Three removable cooling fans installed in the rear for optimum cooling system 1 2 Product Specifications General specification Construction Heavy duty steel Disk Driver One 5 25 drive and Two 3 5 drive FDD8 HDD space Cooling Fan Three Ball bearing fans 8cmX3 Indicator Two LEDs to monitor the status of HDD and Power UBS PORT In the front panel Dimension gt 431 W X176 H X454 7 D mm Passive Backplanes Optional Features 14 slots Full length backplanes with the options BP 14S BP 14SD PCI 14S PCI 14S2 PCI 13SD PX 14S PX 14S2 and IP 14S Power Supply Optional power Supply for the Rack 814 are ACE 920A 932T 935A1 925C 916V For the DC input Power Supply you may choose ACE 932T ACE 925T ACE 925C or ACE 916V Optional ACE C232 redundant power supply for the RACK 814 Working Environment Operating Temperature 0 50 C Relative Humidity 5 95 Relative Vibration 5 17Hz 0 1 double amplitude displacement 17 640Hz 1 5G acceleration peak to peak Shock 10G acceleration peak to peak Safety approval meet CE FCC Cooling Fan Three removable Ball Bearing Cooling Fan 8cmX3 Drive Capacity One 5 25 drive one 3 5 FDD drive and one 3 5 HDD drive space 1 3 Dime
Download Pdf Manuals
Related Search