LINDY User Manual
Contents
1. BIND Ye CONNECTION PERFECTION Modular Matrix Range User Manual English No 38250 38251 38252 38253 38254 38255 38256 38257 38259 www lindy com Tested to Comply with C FCC Standards For Home and Office Use LINDY ELECTRONICS LIMITED amp LINDY ELEKTRONIK GMBH FIRST EDITION April 2015 User Manual English Thank you for purchasing from the LINDY Modular Matrix range of products This range of products is designed to allow you to create a matrix with 8 16 or 32 input and output ports The input ports can be a choice of C6 HDBaseT HDMI DVI or VGA while the output ports can be HDMI DVI or C6 HDBaseT Any of the inputs can be combined with any of the outputs to create a UHD 4Kx2K 830Hz display over distances of up to 70m and 1080p up to 100m The modular design provides the ultimate in flexibility for audio and video distribution as a matrix convertor or an extender in retail product demonstration training and public display application in schools pubs etc Modular Matrix including control board with spaces for 2 4 or 8 modular boards R Blaster Blanking plates fitted to the rear of the units IR Extender Power Cord 2x for 16 and 32 port Chassis Remote control inc battery User manual Input boards choose from C6 HDBaseT HDMI DVI D and VGA Output boards choose from HDMI DVI D and C6 HDBaseT Modular Chassis Supports HDMI 4K C6 HDMI Extender 4K VGA WUXGA and2. muted I muted Pull the input x 01 8 Hot Plug Detect signal fo LOW User Manual English Command Descnphon Pull the input x 01 8 Hot Plug Detect signal to HIGH Report all input Hot Plug Detect signal status EDIDMODE x y set EDID mode y 1 3 to Input x 01 8 EDIDMODEALL x The EDID mode x 1 3 of All Input EDIDPORT x y set EDID Assigned Port y 01 8 to Input x 01 8 EDIDPORTALL x The EDID of All Inports is assigned to Output x 01 8 EDIDSTATUS Report all input EDID mode amp port IRMASKOUT x y z Set output port board IR mask x SINK SRC y 1 8 All z 0 1 IRMASKCPU x y z Set CPU board allout IR mask x SINK SRC OUT y 1 8 All z0 1 SHOWIRMASKOUT x y Write UART string to output port x SINK SRC y 1 8 All SHOWIRMASKCPU x y show CPU board IR mask status x SINK SRC OUT y 1 8 All UART x y str Write UART string to output port x in out y 01 8 str String UARTBAUD x y Setting output port x 01 8 UART baud rate y masa Show output pon UART baudroie TEMPSTATUS Show temperature sensor values yl y2 SESNMASK Seling subnet masks IPCONFIG Display the current IP config User Manual English Command Description Defaults DHCP Buzzers Seemepgime SAVETO x Save as Preset x 1 8 RECALLTO x Recall Preset x 1 8 RESET System Reset to O111 0212 0313 0414 OS13 VERSION Display controller firmware version NOTE All commande are case sensitive and m
3. setting of the Input output ports 8 positions available 13 Recall This button will allow you to recall the saved pre sets 14 Enter Press this button to confirm the setting or selection La eS T ap eA al Fale e effi N menu l SAVE o i IE G EL E l racet e am dk agpuw x 0 ENTER EI Geo Rear Panel Note t 1 2 he example below shows a 16x16 matrix fitted with HDMI input and HDMI output boards Output 1 16 Connect your display devices to the output ports Central CPU Board with the following connections a IR In Extend your IR receiver port using the included IR receiver b RS 232 Connect a D Sub 9 pin cable from a PC Laptop for RS232 control of the Matrix or connected devices c Control Connect an active network cable for Telnet Web GUI control d IR All Out In Reserved e Service This port is reserved for firmware update only f Output 0 This port is not activated 3 Input 1 16 Connect your source devices to the input ports on the lower part of the unit gt Power The device will automatically turn on when the power cable is connected 5 Ventilation fan The fan will be active when the device is switched on The vent must not be blocked or covered and must have adequate space to allow ventilation User Manual English Front Panel 16x16 Version N 12 13 LCM Displays the status of each input and output plus options available when in Menu
4. 45 Shielded Female C6 amp 1 x RJ45 Network ports User Manual English Ethernet Speed 100Mbps Video Resolutions PC VGA WUXGA HD 480i 1080p amp 4Kx2K 30Hz Audio Transmission LPCM7 1CH Dolby TrueHD Dolby Digital Plus DTS HD Master Audio 32 192KHz sample rate Power Consumption 45W Cable Type Pixel Clock Rate Video Data Rate Supported Video eee lt 225 MHz lt 5 3 Gbps Up to 1080p60Hz gt 225 MHz gt 5 3 Gbps Ultra HD Video 4K2K 30Hz CE FCC Statement CE Certification This equipment complies with the requirements relating to Electromagnetic Compatibility Standards EN55022 EN55024 and the further standards cited therein It must be used with shielded cables only lt has been manufactured under the scope of ROHS compliance CE Konformitatserklarung Dieses Produkt entspricht den einschl gigen EMV Richtlinien der EU fur IT Equipment und darf nur zusammen mit abgeschirmten Kabeln verwendet werden Diese Ger te wurden unter Ber cksichtigung der RoHS Vorgaben hergestellt Die formelle Konformit tserkl rung k nnen wir Ihnen auf Anforderung zur Verf gung stellen FCC Certification This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation You are cautioned that changes or modification not expressiy approved by the party r
5. DVI 1080p resolutions Modular input and output boards can be mixed between multiple interfaces Supports Audio pass through on all boards Supports RS232 Telnet and Web GUI controls Supports multiple EDID modes 16 amp 32 port models have redundant power supplies Rack Mountable Your modular matrix may need some assembly before installing the modular boards please ensure you have taken the appropriate steps to avoid static discharge Assembly should only be attempted by a qualified person and the chassis should not be connected to the power when adding the boards The boards are not hot pluggable and if further boards are to be added the unit must be powered down and unplugged Make sure all your devices are switched off before making any connections Once all the connections are made switch on the devices in this order displays Matrix source devices Front Panel 8x8 Version 1 Power Button amp LED Press this button to turn the Matrix on press it again to put it in standby mode The LED will illuminate red in standby mode If the LED is flashing then the internal temperature is too high and the Matrix needs ventilation User Manual English 2 LCM Displays the status of each input and output plus options available when in Menu mode 3 Lock Button amp LED Press this button to lock all the function buttons on the panel press and hold it again to unlock the buttons The LED will illuminate red when the buttons ar
6. ETTER Input Port 4 Y TER Input Port 8 Y stem Reset Reset Click on the User Setting tab to reset the IP configuration The system will require a reboot of the device every time any of the settings are changed The IP address on the address bar will need to be updated if this is changed in User Setting tab P Address Selection Address Type DHCP AutolP Y SEEN 192 en 5 135 Subnet Mask 255 Les Ges Lg Default Gateway 192 Update Settings User Manual English Connection Diagram Example shows the 8x8 version Smartphone Tablet device for WebGUI control Outputs TV Displays or Projectors N gomes Wireless Power Cable Note In this example an HDMI input module and an HDMI output module are used to create a 8x8 HDMI Matrix Any combination of modules may be used to creafe the required matrix configuration e g a VGA input module to an HDBaseT output RS 232 Equipped PC IR Extender for IR control of the matrix only lt Ag Wi 3m 7m 3m Inputs Blu ray DVD Players Media Players Satellite Receivers Set top Boxes PCs Macs or Games Consoles moa User Manual English Modules The following modules are available for this range of products Output Modules ml S RR RS RR Ne ge 4K2K HDBaseT output module eo eo eo eo e o Op 3 oO oo CH gt 4K2K HDMI output module ER AN AMS ABS ER ES EN E
7. LOW ALL HPDHIGH ALL SHOWHPD STATUSHPD x x 1 B SHOWTEMP STATUSIN KZ xw 1 CU IE II H e KR STATUSALL SIAIUSEDID SEIEDIDNODE ii mm ii 8 SEIEDIDNODE ALL mn mn D IK RDMUTE HPDLOW HPDHIGH N gt SETEDIDPORT ii pp lt ii 41 8 pp 61 8 gt SETEDIDPORT ALL mn Cpp pp ACTIVE INDETECT OUT DETECT IPCONFIG SETIP lt IP gt lt SubNet gt lt GW gt RSTIP SETIPADDR lt IP gt SETSNMASK lt SubNet gt SETGWADDR lt GW gt R Pull the Hot Plug Detect Pull the Hot Plug Detect signal to HIGH Show temperature sensor values yi y English ly connected to the Matrix type HELP and press enter to see the ojx H Power d Power On Systen Reset to 0111 0212 0313 0414 0515 lt Output BB set to Input 1 8 11 Output set to Input ew deo mute command at output interface Video unmute command at output interface Mute all outputs Unnute all outputs Show mute status of all outputCBenot muted L nuted ad MUTE Status at Output signal to LOW set All Input HPD to Low Set All Input HPD to High Report ALL Input Hot Plug Detect signal status hou HPD status of input x d amp Report Input connection status port Qutput connection status Report ALL Qutput connection status Report ALL Input EDID nodebport UR mn 1 3 gt Set EDID modeCnmm to Input ii 1 4 The EDID mode lt mm of All Input iid Set EDID Assigned Port pp to Input i
8. R d 38256 DVI output module Gi o d n d 38254 Input Modules A ad ad ad lad 38257 VGA input module eg OE ER VER ER EEE 38255 DVI input module Boa o 2 eg EE E e 38253 4K2K HDMI input module zb IW NW WW WW e 38258 4K2K HDBaseT input module Output Modules C6 using HDBaseT technology 38259 Video Bandwidth 300Mhz 10 2Gbps Features Audio Video POH Power over HDBaseT IR RS232 amp Ethernet Output Ports 8 x RJ45 Shielded Female C6 8x IR Extender 8 x IR Receiver amp 1 x RJ45 Network ports Ethernet Speed 100Mbps Video Resolutions PC VGA WUXGA HD 480i 1080p amp 4Kx2K 30Hz Audio Transmission LPCM7 1CH Dolby TrueHD Dolby Digital Plus DTS HD Master Audio 32 192KHz sample rate Power Consumption 45W PoH Module 10W port Cable Type Pixel Clock Rate Video Data Rate Supported Video BEE lt 225 MHz lt 5 3 Gbps Up to 1080p60Hz gt 225 MHz gt 5 3 Gbps Ultra HD Video 4K2K 30Hz User Manual English Data rates lower than 5 3 Gbps or below 225MHz TMDS clock HDMI 38254 Video Bandwidth Output Ports Video Resolutions Audio Transmission Cable Lengths Power Consumption DVI 38256 Video Bandwidth Output Ports Video Resolutions Audio Transmission Cable Lengths Power Consumption Input Modules HDMI 38253 Video Bandwidth Input Ports Video Resolutions Audio Transmission Cable Lengths Power Co
9. ar Panel Note the example below shows an 8x8 matrix fitted with HDMI input and HDMI output boards 1 Output 1 8 Connect your display devices to the output ports 2 Central CPU Board with the following connections a IR In Extend your IR receiver port using the included IR receiver User Manual English mo O INPUT a Se Ar 1 8 gt Le OUTPUT BE E D b RS 232 Connect a D Sub 9 pin cable from a PC Laptop for RS232 control of the Matrix or connected devices c Control Connect an active network cable for Telnet Web GUI control d IR All Out In Reserved e Service This port is reserved for firmware update only f Output 0 This port is not activated Input 1 8 Connect your source devices to the input ports on the lower part of the unit Power The device will automatically turn on when the power cable is connected Ventilation fan The fan will be active when the device is switched on The vent must not be blocked or covered and must have adequate space to allow ventilation N H Ka Front Panel 16x16 Version LCM Displays the status of each input and output plus options available when in Menu mode IR Window Receives the signal from your infrared remote control Power Button amp LED Press this button to turn the Matrix on press it again to put it in standby mode The LED will illuminate red in standby mode Ifthe LED is flashing then the internal temperature is t
10. e locked 4 Return Press this button while in Menu mode and you will be taken back a step 5 Menu Press this button to enter the Menu 1 EDID a Standard EDID use the built in EDID which supports video up to 1080p 60HZz WUXGA 60RB and Audio LPCM 2CH b Dynamic EDID Copies the first connected output device EDID c Manual EDID Uses the EDID of each device connected to the input output ports a IP address b Netmask c Gateway 3 Temperature a Temperature 1 b Temperature 2 shows the internal temperature of the device 4 LCM Contrast range from 1 4 Left Right Arrows Use these buttons to scroll through the pages while in the menu mode 7 Save Press this button to save the current setting of the Input output ports 8 positions available 8 Recall This button will allow you to recall the saved pre sets 9 Enter Press this button to confirm the setting or selection 10 All Press all then the input port then enter to display the same signal on all ports 11 Out In Use these buttons to select the input source you want to show on an output display The sequence should be to select the output ports display from the top row of buttons then select the input source device 12 1 8 The numbers relate to the input and output ports on the rear of the unit es U ma C OL POWER MI N SAVE ALL amp LOCK RETURN RECALL ENTER Ip IE Kal emmim O 000 Re
11. esponsible for compliance could void your authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation LINDY Herstellergarantie Hinweis f r Kunden in Deutschland LINDY gewahrt fur dieses Produkt Uber die gesetzliche Regelung in Deutschland hinaus eine zweijahrige Herstellergarantie ab Kaufdatum Die detaillierten Bedingungen dieser Garantie finden Sie auf der LINDY Website aufgelistet bei den AGBs Hersteller EU EU Manufacturers LINDY Elektronik GmbH Markircher Str 20 DE 68229 Mannheim GERMANY T 49 0 621 47005 0 info lindy de LINDY Electronics Ltd Sadler Forster Way Teesside Industrial Estate Thornaby Stockton on Tees TS17 9JY United Kingdom T 44 0 1642 754000 postmaster lindy co uk Recycling Information WEEE Waste of Electrical and Electronic Equipment Recycling of Electronic Products Europe United Kingdom In 2006 the European Union introduced regulations WEEE for the collection and recycling of all waste electrical and electronic equipment It is no longer allowable to simply throw away electrical and electronic equipment Instead these products must enter the recycling process Each individual EU member state has implemented the WEEE regulation
12. hen the device is switched on The vent must not be blocked or covered and must have adequate space to allow ventilation User Manual English Remote Control 1 Output Output port selection 2 Input Input port selection 3 Enter Press to confirm the present input output selection 4 Clear Press to clear the present input output selection RS 232 Protocols CMSI 88 Remote Controller mn eg D rr Baud Rate 19200bps Data Bit 8 Bits Parity None Stop Bit 1 Flow Control None User Manual English RS 232 amp Telnet Command Command Description Power on Power off Output x 0 8 set to input y 1 8 All output set to input x 01 8 Oxly ALLOUT x ACTIVE INDETECT OUTDETECT PORTSTATUS HDCPON x HDCPOFF x Report I O active channels Input channels detect indicator Output channels detect indicator Report all output connection status Setting input port x 01 8 HDCP on Setting input port x 01 8 HDCP off HDCPONALL Setting all input port HDCP on HDCPOFFALL Setting all Input port HDCP off HDCPSTATUS Show HDCP status of all output O HDCP disable 1 enable MUTEO x Video mute command at output x 0 8 interface Video unmute command at output x 0 8 interface MUTEI x Video mute command at input x 1 8 interface Video unmute command at input x 1 8 interface MUTEALL Mute all outputs Unmute all outputs MUTESTATUS Show mute status of all output O not
13. i Ihe EDID of All Inports 41 3 is assigned to Output Report 7 0 active channels Input channels detect indicator Output channels detect indicator Display the current P conf ic i f d Setting IP SbuNet GateWayfStatic IP IP Configuration Was Reset To Factory Defaults lt DHCP Setting IP address Setting subnet nask Setting gatevay IP address Type IPCONFIG to show all IP configurations To reset the IP type RSTIP To use a Static IP type SETIP The full list of commands are in the previous section User Manual English Web GUI Control To access the Web GUI open a web browser and type the devices IP address The browser will display the devices status control and user setting pages TT Power Status Wenn ON IP Status WERE 192 168 5 135 255 255 255 0 LE Ei 192 168 5 254 NER OE 12 00 EA 7A F1 Http Port Number SU Telnet Port Number 73 Matrix Status ARCA dE InPut Port 4 Date CH InPut Port 8 TT A AER InPut Port 3 DT Ad InPut Port 7 eina oa InPut Port 2 16 3 MD odil InPut Port 6 Oaa T InPut Port 1 Oina odisea InPut Port 5 Click on the Control tab to control power input output ports EDID amp Reset mode ower Control PowerON PowerOFF latrix Control EEE Input Port 1 e Input Port 2 e RER Input Port 3 e Oana uii Input Port 5 v Oana en Input Port 6 Y una Input Port 7 v EIS HTC RER Select Input Port Y W
14. iature devono essere riciclate Ogni stato membro dell EU ha tramutato le direttive WEEE in leggi statali in varie misure Fare riferimento alle leggi del proprio Stato quando si dispone di un apparecchio elettrico o elettronico Per ulteriori dettagli fare riferimento alla direttiva WEEE sul riciclaggio del proprio Stato LINDY No 38250 38251 38252 38253 38254 38255 38256 38257 38259 C 1 Edition April 2015 www lindy com Le Tested to Comply with C FCC Standards For Home and Office Use
15. ion buttons on the panel press and hold it again to unlock the buttons The LED will illuminate red when the buttons are locked Save Press this button to save the current setting of the Input output ports 8 positions available Recall This button will allow you to recall the saved pre sets Enter Press this button to confirm the setting or selection User Manual Der i O vi Ze MENT POWER RE l RN IN Z gt 2 f e VS da h STAN Pe l EA ri U D o Q l H J I m L s v 5 m lt gt Rear Panel English Note the example below shows a 32x32 matrix fitted with HDMI input and HDMI output boards 1 Output 1 32 Connect your display devices to the output ports 2 Central CPU Board with the following connections a IR In Extend your IR receiver port using the included IR receiver b RS 232 Connect a D Sub 9 pin cable from a PC Laptop for RS232 control of the Matrix or connected devices Control Connect an active network cable for Telnet Web GUI control G d IR All Out In Reserved e service This port is reserved for firmware update only f Output 0 This port is not activated 3 Input 1 32 Connect your source devices to the input ports on the lower part of the unit 4 Power The device will automatically turn on when the power cable is connected 5 Ventilation fan The fan will be active w
16. mode Power Button amp LED Press this button to turn the Matrix on press it again to put it in standby mode The LED will illuminate red in standby mode If the LED is flashing then the internal temperature is too high and the Matrix needs ventilation Return Press this button while in Menu mode and you will be taken back a step Left Right Up Down Arrows Use these buttons to scroll through the pages while in the menu mode Menu Press this button to enter the Menu 1 EDID a Standard EDID use the built in EDID which supports video up to 10800 60Hz WUXGA 60RB and Audio LPCM 2CH b Dynamic EDID Copies the first connected output device EDID c Manual EDID Uses the EDID of each device connected to the input output ports 2 IP a IP address d Netmask e Gateway 3 Temperature Shows the internal temperature of the device 6 LCM Contrast range from 1 4 Adjust the LCM contrast from 1 to 4 All Press this button to assign the same input to all outputs 1 9 The numbers relate to the input and output ports on the rear of the unit Out In Use these buttons to select the input source you want to show on an output display The sequence should be to select the out in button then the input then the out in and then the output finally select enter Plus This allows you to select multiple outputs for a selected input and can only be used in conjunction with the OUT IN button Lock Button amp LED Press this button to lock all the funct
17. nsumption DVI 38255 Video Bandwidth Input Ports Video Resolutions Audio Transmission Cable Lengths Power Consumption VGA 38257 Input Ports Video Resolutions Audio Transmission Cable Lengths Power Consumption 300Mhz 10 2Gbps HDMI Type A Female PC VGA WUXGA HD 480i 1080p amp 4Kx2K 30Hz LPCM7 1CH Dolby TrueHD Dolby Digital Plus DTS HD Master Audio 32 192KHz sample rate Maximum distance 15m using LINDY CROMO cable 22W 225Mhz 6 75Gbps DVI Female PC VGA WUXGA 60RB HD 480i 1080p LPCM7 1CH Dolby TrueHD Dolby Digital Plus DTS HD Master Audio 32 192KHz sample rate Maximum distance 15m using LINDY Premium SLD cable 20W 300Mhz 10 2Gbps HDMI Type A Female PC VGA WUXGA HD 480i 1080p amp 4Kx2K 30Hz LPCM7 1CH Dolby TrueHD Dolby Digital Plus DTS HD Master Audio 32 192KHz sample rate Maximum distance 15m using LINDY CROMO cable 22W 225Mhz 6 75Gbps DVI Female PC VGA WUXGA 60RB HD 480i 1080p LPCM7 1CH Dolby TrueHD Dolby Digital Plus DTS HD Master Audio 32 192KHz sample rate Maximum distance 15m using LINDY Premium SLD cable 20W VGA Female amp 2 5mm jack includes 8 x 2 5mm to 3 5mm adapters PC VGA WUXGA 60RB Stereo Maximum distance 15m using LINDY Premium VGA cable 22W C6 using HDBaseT technology 38258 Video Bandwidth Features Output Ports 300Mhz 10 2Gbps Audio Video POH IR RS232 amp Ethernet 8 x RJ
18. oo high and the Matrix needs ventilation Left Right Up Down Arrows Use these buttons to scroll through the pages while in the menu mode Return Press this button while in Menu mode and you will be taken back a step Menu Press this button to enter the Menu 1 EDID a Standard EDID use the built in EDID which supports video up to 1080p 60HZ WUXGA 60RB and Audio LPCM 2CH b Dynamic EDID Copies the first connected output device EDID c Manual EDID Uses the EDID of each device connected to the input output ports 2 IP a IP address D Netmask c Gateway 3 Temperature Shows the internal temperature of the device 5 LCM Contrast range from 1 4 Adjust the LCM contrast from 1 to 4 All Press this button to assign the same input to all outputs Out In Use these buttons to select the input source you want to show on an output display The sequence should be to select the out in button then the input then the out in and then the output finally select enter 1 9 The numbers relate to the input and output ports on the rear of the unit User Manual English 10 Plus This allows you to select multiple outputs for a selected input and can only be used in conjunction with the OUT IN button 1 Lock Button amp LED Press this button to lock all the function buttons on the panel press and hold it again to unlock the buttons The LED will illuminate red when the buttons are locked 12 Save Press this button to save the current
19. s into national law in slightly different ways Please follow your national law when you want to dispose of any electrical or electronic products More details can be obtained from your national WEEE recycling agency Germany Deutschland Die Europ ische Union hat mit der WEEE Direktive Regelungen fur die Verschrottung und das Recycling von Elektro und Elektronikprodukten geschaffen Diese wurden im Elektro und Elektronikgerategesetz ElektroG in deutsches Recht umgesetzt Dieses Gesetz verbietet das Entsorgen von entsprechenden auch alten Elektro und Elektronikger ten ber die Hausm lltonne Diese Ger te m ssen den lokalen Sammelsystemen bzw rtlichen Sammelstellen zugef hrt werden Dort werden sie kostenlos entgegen genommen Die Kosten f r den weiteren Recyclingprozess bernimmt die Gesamtheit der Ger tehersteller France En 2006 l union Europ enne a introduit la nouvelle r glementation DEEE pour le recyclage de tout equipement lectrique et lectronique Chaque Etat membre de I Union Europ enne a mis en application la nouvelle r glementation DEEE de mani res l g rement diff rentes Veuillez suivre le d cret d application correspondant a l elimination des d chets lectriques ou lectroniques de votre pays Italy Nel 2006 l unione europea ha introdotto regolamentazioni WEEE per la raccolta e il riciclo di apparecchi elettrici ed elettronici Non e piu consentito semplicemente gettare queste apparecch
20. ust be followed by a carriage return to be executed These commands are for C6 HDBaseT modules only SINK The connected receiver SRC Output port on the module ALL IR all on the CPU board 0 1 Off On RS 232 Protocols Before attempting to use telnet control ensure that both the matrix and the PC Laptop are connected using an active network To access the telnet control in Windows 8 click on the start menu and type CMD and press enter When using Windows 7 click on the start menu and type CMD in the search field and press enter When using Windows XP click on the Start menu and click on Run type CMD and then press enter When using a Mac go to Go Applications Utilities and choose Terminal Once in the command line interface type telnet then type the IP address of the unit followed by a space and 23 then hit enter NOTE The IP address of the Matrix can be displayed on the devices LCM monitor by pressing the Menu button twice Microsoft Windows Version 6 1 7600 s Copyright lt c gt 2009 Microsoft Corporation All rights reserved C Users telnet 192 168 5 80 23_ User Manual When you have successful available list of commands lelcome to Matrix TELNEI X P elnet help PO Pi RESET OxxIxx x ALR ALLOUI xxx 41 gt MUTE xx x 0 B UNMUTE e H ek MUTERLL UNMUTEALL SHOWMUTE xx x 4B Re xx CxS LSD xx Cx LBD HPD
Download Pdf Manuals
Related Search