Supernova™ Core Installation manual
Contents
1. Frame pieces 5 mm Rod Hook D aan M5 bolt Bolt fixture Cover strip i N ia er L i Nee 1 4 Z P d Z Adjustment piece www dnp dk dnp denmark as Skruegangen 2 DK 2690 Karlslunde Denmark Tel 45 46 16 51 00 Fax 45 46 16 52 00 dnp dnp dk Supernova c p Supernova is a registered trademark of dnp denmark as visual experience2. Supernova Core Installation manual Supernova c p Supernova is a registered trademark of dnp denmark as visual experience Warnings Follow all assembly instructions Incorrect assembly can lead to screen damage and invalidate the dnp warranty Be careful not to kink the film during handling as it could make permanent marks in the film properties Please note that the backside of the film is more sensitive than the frontside and should thus A A A Keep sharp objects away from the film as they can scratch the film and destroy the optical A be handled more carefully A Do not apply pressure to the screen material once it is mounted on the frame Required tools and materials Phillips screwdriver M6 Allen key Rubber hammer Level Tape measure 2 appropriate mounting screws and wall plugs Box contents Check box for Installation manual this document Rolled up screen film image area facing out Left right frame pieces short Top bottom frame pieces long Inner corner brackets Adjustment pieces fixture bolt hook Metal rods Wall mounts Corner covers rear Cover strips rear M6 nuts M6x20 bolts for wall mounts M6x20 Allen bolts for inner corner brackets Assembly procedure See illustration on last page 1 Prepare a clean flat surface to assemble the screen Use a protective covering if necessary Determine how much space is needed for your size of screen 2 Unpack ever
3. ake a perfect flat image area Snap the cover strips onto the back of the frame pieces a small rubber hammer is recommended but is not imperative Remember to make space for the cover corners Snap the cover corners onto the back of the frame corners a small rubber hammer is recommended but is not imperative Attach the wall mounts onto the rear side of the frame in both top corners by screwing the M6x20 bolts into the M6 nuts previously inserted in the frame pieces section 6 The screen is now assembled and ready to be mounted on the wall Supernova c p Supernova is a registered trademark of dnp denmark as visual experience Screen installation N Planning screen location 1 Determine the space requirements for your installation 2 Measure the required distance between two mounting screws for your size of screen 3 Level out and drill two mounting screws into the wall Use appropriate screws that are strong enough and that fit in the bracket slots Use wall plugs if needed Planning projector location The projector can be positioned freely on a vertical centerline perpendicular to the screen up to 5 above or 5 below the image area Projection distance must be based on the manufacturer s specifications for the exact model and lens choice Illustration Supernova Core frame assembly guide M6boltt Cover strip Pg L r P ri ri f Ca k TOPe j E 4 Wall mount
4. nto each end of the side frame pieces four in total Assemble the frame by sliding the inner corner brackets from the side pieces into the top and bottom frame pieces Do one side at a time Mount loosely first then affix by tightening the M6x20 Allen bolts Distribute the adjustment pieces evenly along the top bottom and sides Take out carefully the screen roll from the box do not unroll it Make sure that the image area is facing out a serial number label is placed in the upper right corner on the rear side not visible from the front If the screen has been rolled incorrectly contact your Supernova dealer before you proceed Open the film roll carefully until the top or side metal rod is accessible depending on the screen size the film is rolled either horizontally or vertically Mount the top or the side of the film by placing the metal rod in the hooks at each eyelet in the film Tighten slightly Unroll the film carefully without kinking or scratching the front or backside surface Mount the bottom or opposite side of the film by placing that metal rod in the hooks at each eyelet in the film Tighten slightly Slide the missing metal rods into the unused rod pockets of the film Mount the hooks in the frame pieces to the metal rods at each eyelet in the film Do one side at a time Adjust the adjustment pieces around the screen until the film is in correct position Tighten the adjustment pieces around the screen to m
5. ything but the film roll and arrange the items nearby Be careful not to scratch the film when taking everything else out of the box 3 Place the frame pieces with the front side facing down Note that if the working surface is not properly cleaned or covered before use particles can stick to the frame surface material and in worst case damage it 4 Assemble the adjustment pieces fixture bolt hook see illustration on last page Supernova c p Supernova is a registered trademark of dnp denmark as visual experience 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mount the adjustment pieces in the frame pieces by sliding the fixture into the groove of the frame piece and orientate the hook end toward the middle of the screen Mount the same number of adjustment pieces as there are eyelets in the screen material Do the same for each top bottom piece and in each side frame piece If your screen has vertical support s remember to slide in the square M6 nut s in between the fixtures at correct place Example If there is one vertical support and eight eyelets the square M6 nut for the vertical support must have four fixtures at each side For the wall mounts Mount two M6 nuts in each side of the top frame piece outside the adjustment pieces by sliding them into the groove Mount one M6 nut in the top of each side frame piece above the adjustment pieces Slide an inner corner bracket i
Download Pdf Manuals
Related Search