USER MANUAL - Camboard Electronics
Contents
1. NET port is wired as shown in Figure 5 K NET PINOUT K NET B G A 12V Black GND Figure 5 K NET PINOUT Connection 1 Available for download at the Kramer Web site www kramerelectronics com F 9 won boarde Tel 07131 911201ce info camboard de Fax 07131 911203 im Vertrieb von Operati S AMBOARD Electro pi cs 6 Operating the SL 10 Master Room Controller You can operate your SL 10 using e AnRC family remote controller To operate your device using an RC remote controller see the Kramer K Config Guide e The optional RC 4 infrared remote control transmitter To operate your device using the infrared remote controller see the User Manual packed with the remote controller e A PC running Site CTRL control software To operate your device using Site CTRL see the Site CTRL and Web Access Online User Guide 7 Technical Specifications The SL 10 technical specifications are shown in Table 2 Table 2 SL 10 Master Room Controller Technical Specifications INPUTS 2 RS 232 RS 485 2 GPI O and K NET on terminal block connectors Ethernet on an RJ 45 connector 1 infrared built in receiver 1 infrared on a 3 5mm mini jack connector 1 USB for programming OUTPUTS 3 infrared 5 relays 36V AC or DC 2A 60VAC maximum on non inductive load and 2 GPI O on terminal block connectors DEFAULT IP SETTINGS IP number 192 168 1 39 Mask 255 255 0 0 Gateway 0 0 0 02. of Kramer s recycling arrangements in your particular country go to our recycling pages at http www kramerelectronics com support recycling www2camboard de Tel 07131 911207 amp info eamnboard de Fax 07131 911203 im Vertrieb von CAMBOARD Electronics 2 4 Quick Start This quick start chart summarizes the basic setup and operation steps miem SL 10 Quick Start Guide Te E Eea h This guide helps you install and use your product for the first time For more detailed information go an fa to http Avww kramerelectronics com support product_downloads asp to download the latest manual Wat or scan the QR code on the left Step 1 Check what s in the box X The SL 10 Master Room Controller a 1 Quick start guide A 1 Power supply 12V DC 4 Rubber feet Step 2 Install the SL 10 Mount the machine in a rack using the RK 13 rack adapter or place on a table Step 3 Connect the inputs and outputs a 2 a R Connect the IR outputs Connect the GPI O ports Connect the relays Laptop running Site CTRL Connect the Ethernet Connect the RS 232 Connect the RS 485 Connect the K NET Connect the iR sensor ABN AAA GONE Lighting System IR INPUT FUNCTIONALITY u You can use the built in IR nl i pron receiver on the front panel or instead use the optional external wired IR receiver with connected to the 3 5 mm jack To a compatible Screen IR INPU
3. INDICATORS LED indicator for each function POWER SOURCE 12V DC 290mA DIMENSIONS 14 3cm x 12 2cm x 4 4cm 5 6 x 4 8 x 1 7 W D H WEIGHT 0 6kg 1 Albs ACCESSORIES Power supply OPTIONS RK 13 19 rack mount RC 4 remote controller IR emitter cables IR sensor cable 1 Available for download at the Kramer Web site www kramerelectronics com 2 The RC 4 is configured via the Kramer K Config software 3 Specifications are subject to change without notice 4 P N C A35 IRE 10 two IR Emitter Extension Cables are also available a 15 meter cable and a 20 meter cable 5 P N 95 0104050 www tamboard de Tel 07131 91130 ee INo camboar Fax 07131 911203 im Vertrieb von CAMBOARD Electronics LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of th
4. T RC unit Step 4 Connect the power Connect the12V DC power adapter to the SL 10 and plug the adapter into the mains electricity Step 5 Operate the SL 10 Operate via the RC keypad IR remote control K NET or ETHERNET An ww WM Mboard de Tel 07131 91120 1ce info camboard de Fax 07131 911203 im Vertrieb von CAMBOARD Electronics 3 Overview The SL 10 is a highly versatile controller that acts as an all in one control processor for control of A V equipment especially projectors and associated equipment in any room such as classrooms boardrooms or auditoriums It streamlines operations and simplifies control by integrating audio video and computer video sources into a centralized system The SL 10 Master Room Controller features An Ethernet port for controlling several AV products over ETH 2 general purpose I O ports that can be configured as analog inputs digital inputs or digital outputs for interfacing with a variety of devices such as sensors switches LEDs and relays 2 bidirectional RS 232 ports that control AV equipment such as projectors LCD and PDP displays power amplifiers switchers and scalers 5 relay contact closure ports that control other room items related to the AV system such as raising and lowering drapes the screen or the projector IR control on two inputs one built in receiver and the other on a 3 5mm mini jack and three outputs on terminal blocks IR Learning
5. ature Function 11 PROG Switch For service use only 12 12V DC Socket 12V DC connector for powering the unit 13 IR built in receiver Accepts IR remote commands INPUTS and STATUS LED 14 3 5mm Mini Jack Connects to an external IR receiver 15 RELAY LEDs 16 RLEDs Illuminate when a relay is active 1 to 5 Illuminate when an IR port is active 17 NET LED Illuminates when The Ethernet link is active 18 K NET LED Illuminates while transmitting over K NET 19 RS 485 LED Illuminates while transmitting receiving on an RS 485 port I 20 RS 232 Tx Rx LEDs luminate while transmitting receiving on an RS 232 port 1 to 2 21 GPI O LEDS Illuminate while transmitting receiving on a general purpose I O port 1 to 2 22 PROGRAM USB Connector Connect to a computer for unit configuration and firmware upgrading 5 Connecting the SL 10 Master Room Controller To connect the SL 10 as the example in Figure 2 illustrates do the following 1 Connect the RELAY terminal block connectors as follows Connect RELAY 1 and 2 to the projector lift Connect RELAY 3 and 4 to the screen Connect RELAY 5 to the lighting system 2 Connect the IR outputs as follows Connect an IR emitter to IR OUTPUT 1 and attach the emitter to the DVD player 3 Connect the GPI O ports as follows Connect GPVO 1 to motion detector 1 Connect GPI O 2 to motion detector 2 4 Connect the RS 232 ports as follows Connec
6. d de Fax 07131 911203 ster Room ua im Vertrieb von Connect CAMBOARD Ele ctronics 5 2 Connecting the RS 232 Interface To connect an AV device to the SL 10 using the RS 232 port connect the RS 232 9 pin D sub port on your device to the RS 232 terminal block on the rear panel of the SL 10 as shown in Figure 3 RS 232 Device Figure 3 RS 232 Connection 5 3 Connecting the RS 485 Interface To connect an AV device to the SL 10 using the RS 485 port connect the RS 485 port on your device to the RS 485 terminal block on the rear panel of the SL 10 as shown in Figure 4 Figure 4 RS 485 Connection wwwscamboard de Tel 07131 911207 amp infTo Ccamnboard de Fax 07131 911203 im Vertrieb von Connect MBO ARD Electronics aster Room er 5 4 Connecting the Ethernet Port The Ethernet connection of the SL 10 allows you to perform all control functions of the SL 10 over the Internet using a PC running the Kramer Site CTRL control program To connect the SL 10 to a network 1 Connect the Ethernet port of the SL 10 to the Ethernet port on a network hub or network router via a straight cable with RJ 45 connectors 2 At the other end connect the Internet to a PC running Site CTRL After connecting the Ethernet port you have to install and configure it For detailed instructions on how to install and configure your Ethernet port see the K Config Guide 5 5 Connecting the K NET Port The K
7. ecial incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state T
8. emitter cables from 1 to 3 GPI O Terminal Blocks Connect to various analog and digital sensors from 1 to 2 RELAYS Terminal Blocks Connect to low voltage relay driven devices from 1 to 5 RS 232 Terminal Blocks Connect to the RS 232 devices from 1 to 2 NID oO BR oOo RS 485 Terminal Block Pins B and A are for RS 485 Pin G may be connected to the shield if required 8 K NET Connector PIN GND is for the Ground connection PIN B and PIN A are for RS 485 and PIN 12V is for powering other units 9 RS 485 TERM Switch Slides down for RS 485 termination slides up for not terminated 10 K NET TERM Switch Slides down for K NET termination slides up for not terminated 1 First disconnect the power supply and then connect it again while pressing the DEFAULT button The unit powers up and loads its memory with the factory default definitions and erases all stored presets 2 K NET is a proprietary Kramer protocol for interconnecting Kramer units 3 The ground connection is sometimes connected to the shield of the RS 485 cable in most applications it is not connected 4 Note that the SL 10 cannot receive power via the K NET connector but can power other units but not another SL 10 inn Ubniboandde 5 Tel 07131 91120 1ce info camboard de Fax 07131 911203 im Vertrieb von Connect MBO ARD Ele tronics ster Room GUO Fe
9. hieve the best performance e Use only good quality connection cables we recommend Kramer high performance high resolution cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Do not secure the cables in tight bundles or roll the slack into tight coils e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your Kramer SL 10 away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building 2 2 Safety Instructions Caution There are no operator serviceable parts inside the unit Warning Use only the Kramer Electronics input power wall adapter that is provided with the unit Warning Disconnect the power and unplug the unit from the wall before installing 2 3 Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details
10. his limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction www camboard de Tel 07131 911201ce info camboard de Fax 07131 911203 im Vertrieb von TR Electronics For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution MINI II Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com www camboard de T l 4 9459 RF29 1ce info camboard de Fax 07131 911203
11. im Vertrieb von CAMBOARD Electronics Kramer Electronics Ltd USER MANUAL Model SL 10 Master Room Controller www camboard de Tel 07131 91120 1ce info camboard de Fax 07131 911203 im Vertrieb von CAMBQARD Electronics Contents 1 Introduction 1 2 Getting Started 1 2 1 Achieving the Best Performance 2 2 2 Safety Instructions 2 2 3 Recycling Kramer Products 2 2 4 Quick Start 3 3 Overview 4 4 Your SL 10 Master Room Controller 5 5 Connecting the SL 10 Master Room Controller 6 5 1 Using the RC 4 IR transmitter 7 5 2 Connecting the RS 232 Interface 8 5 3 Connecting the RS 485 Interface 8 5 4 Connecting the Ethernet Port 9 5 5 Connecting the K NET Port 9 6 Operating the SL 10 Master Room Controller 10 7 Technical Specifications 10 Figures Figure 1 SL 10 Master Room Controller 5 Figure 2 Connecting the SL 10 Master Room Controller 7 Figure 3 RS 232 Connection 8 Figure 4 RS 485 Connection 8 Figure 5 K NET PINOUT Connection 9 Tables Table 1 SL 10 Master Room Controller Functions 5 Table 2 SL 10 Master Room Controller Technical Specifications 10 T i KRAMER www c mboard de Tel 07131 91120 1ce info camboard de Fax 07131 911203 im Vertrieb von CAMBO RD Electronics ntroduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentat
12. ion and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Thank you for purchasing the Kramer MultiTOOLS SL 10 Master Room Controller which is ideal for e Controlling multimedia rooms such as classrooms auditoriums conference rooms and so on while enabling remote control and management of the AV equipment e Production studios rental and staging 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual Go to http www kramerelectronics com to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 1 wwwi amp mboard de Tel 07131 91120 1ce info camboard de Fax 07131 911203 im Vertrieb von CAMBOARD Electronics 2 1 Achieving the Best Performance To ac
13. is product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Who is Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessa
14. ry parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authori
15. t RS 232 port 1 to the DVD player Connect RS 232 port 2 to the projector 5 Connect the IR input as follows Connect IR INPUT 1 to an IR sensor or alternatively connect IR INPUT 1 to an external IR receiver 1 Switch OFF the power on each device before connecting it to your SL 10 After connecting your SL 10 switch on its power and then switch on the power on each device 2 P N C A35M IRR two extension cables are also available a 15 meter cable and a 20 meter cable www scamboard de Tel 07131 91120Tee Nio camDoard de Fax 07131 911203 im Vertrieb von Connect CAMBOARD Ele ctronics ster Room GUO 6 Connect the RS 485 to several Kramer matrices for example 7 Connect the Ethernet port to a network 8 Connect the K NET port to any RC device with K NET IR DVD Player Lighting System o Motion Motion Ww p g Detector 1 Detector 2 Projector K NET Projector Screen Lift To RC 63DL Figure 2 Connecting the SL 10 Master Room Controller 5 1 Using the RC 4 IR transmitter You can use the optional RC 4 IR transmitter as an auxiliary control panel and initiate configured control triggers tefer to the K Config guide via the built in IR receiver on the front panel or instead via an optional external wired IR receiver which exists in several cable lengths shown in Figure 2 1 Not shown in Figure 2 2 Model C A35M IRR 50 F 7 nan bosrdide Tel 07131 911201ce info camboar
16. that learns commands from any IR remote 1 RS 485 serial port Compatibility with Kramer Site CTRL software for network remote control and management over the Ethernet port A K NET control channel that connects compatible user interfaces and supplies power and control data over a single cable A USB port for uploading a configuration file Status LEDs for all functions Flexible control via Ethernet K NET RS 485 an IR sensor and external IR commands www camboard de Tel 07131 91120 G6 inf Weariboard de Fax 07131 911203 im Vertrieb von Your AM BOARD El lecir fron ics 4 Your SL 10 Master Room Controller Figure 1 and Table 1 define the unit ur fradz chad trelz of INTs cals cl ron Io 9 enn on esa Kise weal mde te En ETHERNET Ltip24 MuitiTooLs 1 Figure 1 SL 10 Master Room Controller Table 1 SL 10 Master Room Controller Functions Feature Function 1 ETHERNET RJ 45 Connects to the PC or other serial controller through computer Connector networking LAN to control several AV products over Ethernet 2 DEFAULT Recessed Press to reset to factory default definitions Pushbutton IP number 192 168 1 39 Mask 255 255 0 0 Gateway 0 0 0 0 IR Output Terminal Blocks Connect to IR
17. zed Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If itis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief sp
Download Pdf Manuals
Related Search