Home

PadPuls M4 User Manual

image

Contents

1. D g GmbH Stettiner Str 38 D 33106 Paderborn 2 Installation and Startup 2 1 Opening the case The case cover can be removed from the lower housing half with the help of a small screwdriver The screwdriver is placed as in the drawing into the small opening at the cover side After light moving of the screwdriver in the displayed direction the cover can be taken off 6 g w f ao T PELL LULL lt 2 2 Activating Coming from factory the PadPuls M4 must first be activated The housing must be opened see drawing and the jumper has to be placed on both pins Then battery operation and data saving is activated on M Bus failure You should also remove the transparent protective foil from the front cover On the back of the PadPuls M4 board there are the follwing control elements unprotect key banery jumper battery operation lt aa serialno gt a E on off PadPuls M4 board p e f the device is not used for a longer time it is advisable to deactivate battery operation by removing the jumper to preserve the battery PadPuls M4 User Manual 25 09 01 Version 1 4 3 P 13 re y GmbH Stettiner Str 38 D 33106 Paderborn 2 3 Connecting The following figure shows the link of four counters with impulse outputs to the PadPuls M4 We recommend
2. Log Window The so called log window is always visible All M Bus communication steps are logged in this window Data is displayed in hexadecimal notation It is possible to mark outputs in the log window and copy them with the keys CTL C to the windows clipboard Then the data can be easily imported to any text editor for documentation As soon as the max storage capacity of the window is achieved no more data is logged If you want to log further you must delete the logged data The following buttons are also always visible Erase log clears all outputs inside the log window Exit terminates the program and stores the current setting of serial port port no into the INI file PadPuls M4 User Manual 25 09 01 Version 1 4 9 GmbH Stettiner Str 38 D 33106 Paderborn 3 4 Sheets M4 Port1 to M4 Port4 ii RELAY MBCONF M Bus Configuration 1 40 Info Prim address 1 Due date ID sec adr foooooon Due date cnt S Water Fz we skid Multiplicator f4 1 Vir 2r 2f 4 lt Stateof ports w k M White protection ops Joon 302 EEPROM Eror Unit 1 v M Tariff A P142 Tariff B P3 4 Current time Freeze Read clock of PC write protect Read write M4 Portl M4 Port2 M4 Port3 M4 Portd STE V Long pulse sampling casos N T Edit and change time 3 16 w S M Bus o s COM Port com x Address 1254 oO g Z EI optical mode
3. Read reads the M Bus device and refreshes the data on the selected sheet Write sends the current options to the pulse converter which saves this data into the non volatile memory The PadPuls M4 changes the options only if the write protect is deactivated It is recommended to read the data after writing and check it Notes 1 The variables Current time Next due date Write protection Long pulse sampling and the command Freeze always apply to all ports Therefore you need to edit these items only in one sheet The write protect should be activated after successful configuration of all ports 2 Please press first the button Connect to meter after connecting a new M Bus device Afterwards all sheets are refreshed 3 Examples for configuration of pulse increment and unit e Water meter with counter 45120 I and 1 Pulse 10 I Choice 1 Unit 101 Multiplicator 1 1 Counter 4512 x 101 Choice 2 Unit 1 l Multiplicator 10 1 Counter 45120 x 11 e Electricity meter with counter 78346 kWh and 64 pulses kWh Choice Unit 1kWh Multiplicator 1 64 Counter 78346 x 1kWh e Electricity meter with counter 112 345 kWh and 1000 pulses kWh Choice Unit 1Wh Multiplicator 1 1 Counter 1123454 x 0 001Wh 4 With activated tariff option the pulses are evaluated with the adjustments of the respective port Therefore you should take care that both ports
4. GmbH Stettiner Str 38 D 33106 Paderborn OY Q PadPuls M4 Art No IM002GD Valid from M Bus generation 12 Art No IM002GD 4 channel pulse collector for wall rail mounting with LCD Contents 1 Functional ASCSCRIUIO kee eos aerate cath eee saeeete beam den aanseten ace cmcenanunamenan coe eckaks 2 2 Installation and Startup etme erane erm eee ene erase eclarten eat a tarte tar ert seer rise elie iar erie rer eter esteamerar Come er tec 3 21 Opening the CaSe mnra aaee aa a ad aia card cae tad Coa a i Cac TAa AAAA 3 22A CIIVALING aa a a N a a E a A et ta Se 3 23 AZOMMOCHING aeai ea hit A a iaa aae hott aeaa athe tte la tte etl fata ede taal lant tak Od it 4 2 4 Mounting TG COSC a cssicetiict cst d cen dcadiacotd tits dite cet tte at ted hed ied et tal cart dts bathe atte 5 3 Parameterization using MBCOMFP ceeeeeeeeeeeenee cette eee ee eeeeaaeeeeeeeeeeeeeeeeaaeeeeeeeeeeeeeee 6 SM IMStANAN OM anaa OA cca beueariss 6 3 2 Operation iepen een een CnUr trees ener ener ener AAEN a Creer es ener eneree tn 6 3 3 eo 12157 6 eee eee ee ee er eer een rer N a E A tnt Cre Teen eres aA 7 3 4 Sheets M4 Port1 to M4 POA es ccecccavs soccdanceecccaneverdencielcdavcrane Gaccesedteeenaaeesae 10 PEO IG Dl ely Stearate Net ee Nee ee NN Nee eee Ne ee he eee eee Ne tes 14 5 NOteS OF IMGIUNGHOMMGS iris ces coce ceca dacs cies tues coasted cans aa tne Coneductiend duccawedindetwenive 15 6 M Bus Tel gramMS accu sas cela ce a ca hie
5. s a s s s a a 2 2 a s a ret wfe e 7 gt s 2 s s s 7 2 4 po ft ft o pe ca peis paee eea o af 2 i i a a al pe pec me RSP_UD telegram A IDo 3 Mano 1 Gen Med TC State VIF1 VIF4 Stand Date LeStD StStn StDat Info Numerator Denominator PStat Numer Denomi PStat CS Stop ator nator a a ae primary address identification no for secondary addressing manufacturer code revision of firmware at this time 12 reserved range 10 1F medium transmission counter number of transmitted RSP_UD most significant bit set bit 7 gt write protected bit 3 set permanent error gt error in EEPROM data selected VIF value information field gt physical unit current counter current date IEC870 5 4 data type F last due date date of the due date counter IEC870 5 4 data type G due date counter next future due date 1 byte with information about tariff and sampling method numerator of pulse increment 1 99 denominator of pulse increment 1 255 0 gt 256 Numerator 1 Pulse VIF Deno min ator state of inputs current input state of the ports 16 25 09 01 Version 1 4 PadPuls M4 User Manual OY Q GmbH Stettiner Str 38 D 33106 Paderborn Byte 48 Info Si ele PNG PR Sa 2S Select number of the port for which the data is va
6. m Display Toggle QO MM CE Por 4 Port 3 Port 2 Port 1 SOOOO0000O0 E6866 866868 M Bus 001234 8 m3 001234 8 m3 4 OFF OF Tariff B Pulses B Tariff A Pulses A 2 4 Mounting the case On the back of the housing there is a special mechanism for mounting the device on a DIN rail according to DIN EN 50022 This mechanism can be removed turned over and fixed on the wall with two screws Afterwards you can mount the device without using a rail The following figures show the two options Rail mounting Wall mounting PadPuls M4 User Manual 25 09 01 Version 1 4 5 GmbH Stettiner Str 38 D 33106 Paderborn OY a 3 Parameterization using MBCONF The configuration of the device must be adapted by the customer to the respective installation The current version 12 of PadPuls M4 requires the use of the program MBCONF for configuration The older DOS version PADCON may not be used anymore 3 1 Installation The software MBCONF for configuration of the pulse adaptor is a 32 bit application which can be executed on IBM PC compatible computers under the operating systems Windows 95 98 NT 4 0 The desktop PC or laptop must have a free serial RS232C interface to connect the M Bus level converter The PadPuls M4 to be parameterized must be connected directly i e as only M Bus device to
7. the primary address of the connected M Bus slave In a direct connection with only one slave you can use the broadcast address 254 Using this address every M Bus device must answer regardless of its own address is used to request data from the slave The type of device is then automatically recognized The items Manufact Generation Type and M Bus State will then be refreshed New sheets are generated depending on manufacturer and type of the M Bus device A single sheet for each channel appears in case of PadPuls M4 The sheets are labelled M4 Port1 for the first M4 Port4 for the fourth channel is an item that shows the 3 letter manufacturer code after successful reading Connect to meter The item is read only shows the software revision of the firmware of the connected M Bus device The item is read only shows the type here PadPuls M4 of the connected device This item is read only shows the M Bus state of the connected device This item is read only If this option is activated devices with an optical interface and protocol according to EN 1434 3 can be read and programmed using an optical reading head e g PadPuls M4 M4L The software always reads the data after writing if this option is activated useful for checking the correct programming 8 25 09 01 Version 1 4 PadPuls M4 User Manual D g GmbH Stettiner Str 38 D 33106 Paderborn
8. Baudrate 2400 Manufact REL Stabe joo EEREEERRRREE tag 2400 v Type Autom readout Connect to meter TX Buffer Erase log 63 10 10 68 53 FE 51 01 7F 66 01 7A G1 O7 79 01 00 BG BH FF FF aa Bigs 13 62 13 66 66 F 46 i i AS 16 Buffer x E5 Exit E Jl Es These sheet shows the current settings and values of the respectively pulse channel port of the PadPuls M4 in this example Port 1 The following input boxes and buttons are used to change the params of the pulse adapter Primary address is the M Bus address of the selected port Values between 1 and ID sec adr Medium 250 can be entered in this field for new assignment of the address After pressing the Write button the software programs this primary address and further variable settings on this sheet into the M Bus device is the 8 digit M Bus ID identification no which is also used for secondary addressing of this port describes the measured medium of the connected meter Examples Oil Water Heat Electricity 10 25 09 01 Version 1 4 PadPuls M4 User Manual GmbH Stettiner Str 38 D 33106 Paderborn Multiplicator Unit Counter Current time Due date Due date cnt Next Due date State of ports Write protection EEPROM error is the pulse increment multiplicator of the connected meter For each registered pulse the device adds multiplicator to th
9. and buttons are always attainable COM Port is the serial port of the PC to which the M Bus level converter is connected The selected port will be saved in an INI file and will be restored on startup Therefore the COM Port has to be configured only once Baudrate ist the transmission speed of the serial port of the PC used for parameterization Possible selections for this used M Bus baudrate are 300 2400 or 9600 baud Attention Baudrates of more than 2400 baud are not supported by all M Bus level converters which PadPuls M4 User Manual 25 09 01 Version 1 4 7 GmbH Stettiner Str 38 D 33106 Paderborn New M Bus Baudrate M Bus Address Connect to meter Manufact Generation Type M Bus State ZVEI optical mode Autom readout are available on the market The selected baudrate must be identical to the baudrate of the M Bus device see New M Bus Baudrate The PadPuls M4 supports the baudrates 300 and 2400 Bd allows reprogramming the baudrate of the M Bus device The new baudrate is sent to the M Bus device after a change in the appropriate selection box If the M Bus slave accepts this command it acknowledges the telegram with the single character bE5 for hexadecimal notation using the old baudrate Afterwards the device switches to the new baudrate This button is not needed for the PadPuls M4 since it automatically detects the baudrate used by the master is
10. ary tariff 005906 41 counter port 3 secondary tariff due date counter port 1 primary tariff STe 31 12 01000248 due date counter port 1 secondary tariff Lm k M GIWh m Lm k M GIWhJ Iim A A 573 31 12 ooeoo e 5 1 due date counter port 3 primary tariff mk M GiWhJ m m J m v A STH 31 12 g00005 3 due date counter port 3 secondary tariff Lm k M GIWh m Cm k M GIWh m z 14 25 09 01 Version 1 4 PadPuls M4 User Manual 5 g GmbH Stettiner Str 38 D 33106 Paderborn 5 Notes on malfunctionings No function in battery mode Battery jumper is not placed Battery is empty voltage min 2 9V No function no display after installation After placing the jumper a reset is although the battery jumper is placed generated using an R C combination and the M Bus is connected It is possible that the reset was not correct Please lift the jumper wait about 10 seconds and place it again Pulses are not counted or wrong Check connection of the pulse meter Activate the extended pulse sampling if your system has a long cables gt 10m b high capacitors c electronic So interface Check configuration especially pulse increment and tariff mode PadPuls M4 User Manual 25 09 01 Version 1 4 15 D e M GmbH Stettiner Str 38 D 33106 Paderborn 6 M Bus Telegrams retin 2 a s e 7 e s e EE ee See Oe t a AC Vaere e e o r
11. e PC the baudrate of the PC the baudrate of the M Bus device and the M Bus primary address which is used for communication After a successful connection with the M Bus device further manufacturer information is shown in the sheet Info and additional device specific sheets are displayed 6 25 09 01 Version 1 4 PadPuls M4 User Manual g GmbH Stettiner Str 38 D 33106 Paderborn 3 3 Sheet Info WI RELAY MBCONF M Bus Configuration 1 40 Info M4 Portl M4 Port2 M4 Port3 M4 Porta Current information about M Bus Please send your and software updates can be questions and comments found on our internet site to our EMAIL address Www RELAY DE i mailto info RE LAY DE Port M Bus a COM Pott COM1 KNE 254 Generation f12 P ZEI optical mode Baudrate 2400 Manufact FEL Meus pT MNNNANENENEI ahs 2400 Type Autom readout Connect to meter Erase log 6 66 BC BB 6 66 b 42 a fl Exit hd Summary of supported meters This sheet shows some photos of supported M Bus devices from the product range of the Relay GmbH the PadMess GmbH and further manufacturer Here are also links to the Internet page from which the current version of the program can be downloaded and to the email address for criticism and suggestions to the program The lower third of this card is likewise visible in every other card Here the following input fields
12. e counter The numerator can take values between 0 no counting and 99 the denominator between 1 and 256 is the physical unit of the counter and of the pulse increment All proper units including variants with power of ten from the DIN EN 1434 3 are offered in the selection list is the accumulated counter It has to be related to the unit mentioned above The counter can be programmed equal to the counter of the connected meter in a range of 0 to 99999999 is the current date and time of day of the internal clock in the format DD MM YY_hh mm This field can be only edited and modified in the PadPuls if the switch Edit and change time is activated The button Read clock of PC transfers once the current date and time of the PC into this window The time of day and the date always apply to all ports of PadPuls M4 is the last due date date of the last storage of the due date counter in the format DD MM YY This field is read only is the counter which was saved at the due date This field is read only is the next future due date date of the next storage of the counter in the format DD MM YY The counter will be saved at 00 00 e g with due date 01 01 at change from 31th of December 23 59 to 1 of January 00 00 This field can be edited and programmed only if the switch Edit and change time is marked The due date always applies to all ports of PadPuls M4 shows the current input state of all ports a closed c
13. have the same pulse increment and unit PadPuls M4 User Manual 25 09 01 Version 1 4 13 P ie C y GmbH Stettiner Str 38 D 33106 Paderborn 4 Display a Display sequence without tariff mode 17 45 time mk M GlWhJ I m 28 02 97 date mk M GIWhJ m b d t 1 Caw Gwar Tm 00004834 mk M GlWhJ ms el00c8 16 xv m k M GlWhJ m counter Port 1 a gt counter Port 2 7 N m k M GiWhJ m gt A 8000345 counter Port 3 Cmk M GlWh J Tm Lo So Vv A 0053906 41 counter Port 4 STI 31 1e 0g001e0 due date counter Port 1 Cm k M G Wh m Cmk MGI AA A STe 31 le 01000248 due date counter Port 2 Cmk MOWI Tm Cmk MOWI m Vv A 573 31 12 00000251 due date counter Port 3 3 be S l gt a c wn uu 3 i lt due date counter Port 4 mn F lt wi Tu a a a a b Display sequence both tariffs activated ai time mk M GlWhJ m 28 02 97 date TaRF at Cmk MGW m mkM A Tar if mk M GIWh m lt k gt IR 3 IK co la co S nu t co RB on gt E y lt 2 gt E g m k M G Wh m3 0000120 mk M GWhyJ m gt un 4 us um gt bi E F gt after key press after 3 seconds gt after key press after 3 seconds counter port 1 primary tariff counter port 1 secondary tariff 0803 4 5 3 counter port 3 prim
14. he bus A built in battery ensures that metering continues if the M Bus is interrupted The integrated display LCD allows an M Bus independent operation as a remote display Another feature of the PadPuls M4 is the due date function Meter data are saved separately at the preset due date at 00 00 hour day change to the due date by the implemented clock with calendar function The due date can be changed without lost of the already stored counters Additionally the M Bus Master can initiate an immediate execution of the due date function by sending of the so called Freeze command A Freeze sent to all pulse collectors using the broadcast address 254 is helpful for generating reading profiles of an M Bus system Afterwards the master software polls the data of all meters The complete configuration data is saved into a non volatile memory EEPROM Additional security is provided by daily saving of meter readings into this EEPROM In case of M Bus fail and empty battery the last saved data is restored on power up The configuration data can be protected against unauthorized manipulation The PadPuls M4 can therefore be switched to protection mode with a special M Bus telegram Subsequent changes to device parameters cannot be made in this operating mode The protection mode can then only be disabled by opening the sealed housing and pressing the unprotect pushbutton for minimum 4 seconds 2 25 09 01 Version 1 4 PadPuls M4 User Manual
15. ial tariff activates a longer charging of the contacts before sampling the inputs This allows higher capacitors and or many pulse generators with So interface photocoupler with capacitors to be connected On delivery the extended pulse sampling is activated The lifetime of battery is increased for about 15 if this feature is not used activation of this check box allows editing and programming of the Current time and Next due date The checkbox is deactivated automatically after successful configuration with Write transmits a command to the PadPuls M4 telling it to freeze the counters The PadPuls M4 then copies the current counter to the Due date counter and the current date to the last Due date The storage is done for all ports simultaneously This the same behaviour as at due date The freeze command can be used with the broadcast address 255 to order all PadPuls to save the current counters Then the M Bus master has enough time to read all meters and get values of the same time reading profiles once gets the current date and time from the clock of the PC and transfers it into the item Current time Transmits a command to the PadPuls M4 to activate write protect The PadPuls M4 then allows no further configuration It is protected against unnoticed manipulation 12 25 09 01 Version 1 4 PadPuls M4 User Manual D g GmbH Stettiner Str 38 D 33106 Paderborn
16. lee calico fae cae 16 7 Technical Dalat Rte aten cnt nila son RAN ald bom anne nile anes on te aca he 19 PadPuls M4 User Manual 25 09 01 Version 1 4 1 P g GmbH Stettiner Str 38 D 33106 Paderborn 1 Functional description The PadPuls M4 serves for the adaptation to the M Bus system of consumption measuring instruments such as current gas or water meters However the meters to be adapted must have a floating pulse output Up to four impulse meters can simultaneous be connected to the inputs of this device Optionally the user can activate a tariff function by which energy or volume pulses are accumulated in separate meter readings for primary and secondary tariffs In this case a floating signal for tariff switch is used at Port 2 and or Port 4 Each port or each tariff of the PadPuls M4 can be read on M Bus using its own primary and secondary address The PadPuls M4 thus acts as four stand alone M Bus Slaves The user configures the pulse collector with the software MBCONF The accumulated pulses are converted into kWh m J or other physical units The user interface of MBCONF allows the operator to get an easy access to the configuration Alternatively the communication and configuration can be done using the optical interface of the pulse adapter It is also suited for mobile reading with a handheld or laptop and an optical reading head When connected to the M Bus the PadPuls M4 is powered from t
17. lid 00 Port1 01 Port2 10 Port3 11 Port4 Tariff A tariff A Port 1 count input Port2 counter tariff signal O tariff off Port2 count input 1 tariff on Port2 tariff signal Tariff B tariff B Port 3 count input Port4 counter tariff signal O tariff off Port8 count input 1 tariff on Port4 tariff signal Sampling duration of a sampling 0 short 0 5ms 1 long 1 5ms rein 2 2 3 4 s 6 7 9 w ul z Pineiro els afar s s 7 8 4 2 4 45 5 rnar ors ves o 0 We 0 ware wan Gen Hed vie tT eie fer 7 7 s 2 s 5 7 0 ee Ge eee 4 eg minat s SND_UD telegram Abbreviations see RSP_UD Port seleced port used with address 254 0 Port1 1 Port2 PAdr new primary address of the port Numerator Numerator of pulse increment 1 99 BCD format Denominator Denominator of pulse increment 1 255 0 gt 256 binary fromat Option Options tariff sampling Coding like Info Byte 48 RSP_UD The PadPuls M4 analyzes the individual data records on the basis of the DIF Therefore the order of the records is allowed to vary Itis also possible to transmit only parts of the SND_UD specified above The manufacturer specific appendix of the telegram is always first analysed and must be included therefore in any case The optional record DIF1 VIF1 Anw selects a port to be addressed with global address 254 This must be always the fi
18. o earth gt 1MQ open gt 1MQ closed lt 2kQ 2nF short sampling 12nF long sampling 30 ms 30 ms 14 Hz Specifications to contact of tariff generator Potential Resistance Maximum capacity incl cable Possible signal wave forms PadPuls contact input Contact voltage Contact current Guaranteed debounce time Connection cable floating insulation to earth gt 1MQ open gt 1MQ closed lt 2kQ 2nF short sampling 12nF long sampling 50 60 Hz or static signals 2 5V to 3 6V 30 pA 5 0 ms maximum 10 m Twisted Pair recommended PadPuls M4 User Manual 25 09 01 Version 1 4 19 D s GmbH Stettiner Str 38 D 33106 Paderborn Current consumption Principle Bus operation Battery standard optional Battery operation Battery lifetime in battery operation Short sampling M Bus physical characteristics M Bus quiescent current Space 0 Bit current M Bus Interface M Bus Protocol Standard Transmission speed Addressing Supported functions Data structure Configuration telegram remote power supply from M Bus with automatic changeover to battery on bus failure max 3 0 mA 2 unit loads no battery loading Lithium 3V type 2 3 AA 1800mAh exchangable Lithium 3V type C 5000mAh at 25 C ca 60uA long sampling standard battery at 25 C ca 3 years optional battery at 25 C ca 8 years Battery lifetime is lengthened by ca 15 if shor
19. ontact is marked This item is read only is marked if the device is protected against programming Then you cannot configure the adapter The protection can be removed after opening the sealable housing and pressing the Unprotect pushbutton for a minimum of 4 seconds is marked if there was an error while reading the non volatile memory In this case you must reconfigure the device PadPuls M4 User Manual 25 09 01 Version 1 4 11 OY a GmbH Stettiner Str 38 D 33106 Paderborn Tariff A P1 2 Tariff B P3 4 Long pulse sampling Edit and change time Freeze Read clock of PC Write protect is used for activation tariff mode on port 1 and 2 The tariff mode will be selected after pressing the Write button if the check box is marked Port 1 is then used as pulse input and port 2 is the tariff switch With an open tariff switch the pulses are accumulated to the counter for port 1 main tariff With a closed tariff contact the pulses increment the counter for port 2 special tariff is used for activation tariff mode on port 3 and 4 The tariff mode will be selected after pressing then Write button If the check box is marked Port 3 is then used as pulse input and port 4 is the tariff switch With an open tariff switch the pulses are accumulated to the counter for port 3 main tariff With a closed tariff contact the pulses increment the counter for port 4 spec
20. rst record in the telegram PadPuls M4 User Manual 25 09 01 Version 1 4 17 B 13 M GmbH Stettiner Str 38 D 33106 Paderborn S T aeter e os fo fe ps a lols Protection Telegram This telegram activates the write protection Treats 2 2 s e 7 u a c or weten e 5s e ater Select telegram old method Select telegram new method Anw specifies the Port of the PadPuls M4 which answers to a REQ_UD2 at address 254 Port1 Anw 00 Port2 Anw 01 Port3 Anw 02 Port4 Anw 03 i AE c cs swp aee e o o we ps a x Freeze telegram On reception of this telegram the pulse adapter saves the current counters of all ports into the due date counters and the current date into the due date 18 25 09 01 Version 1 4 PadPuls M4 User Manual GmbH Stettiner Str 38 D 33106 Paderborn 7 Technical Data Case Mounting Material Colour WxHxD Protection type Environment Operating temperature Storage temperature Humidity non condensing DIN rail according to DIN EN 50022 or wall ABS plastic light grey similar RAL 7035 100 x 75 x 105 mm IP40 0 to 55 C 20 to 60 C 10 to 70 Specifications to contacts of pulse generators Potential Resistance Maximum capacity incl cable Minimum contact duration Minimum pause between contacts Maxium pulse frequenz floating insulation t
21. t sampling is activated typ 2 75 mA max 3 0 mA 2 unit loads quiescent current 1 4 mA typ 13 mA TI TSS721 with 2 x 215Q protection resitors EN1434 3 300 2400 baud with automatic detection Primary and secondary addressing with wildcards per input port 1 primary and 1 secondary address SND_NKE REQ_UD2 SND_UD ignores FCB Bit according to EN1434 3 variable structure Low Byte First Cl 72h length 53 Bytes 1 data record counter 2 data record date and time 3 data record last due date 4 data record last due date counter 5 data record next due date 6 data record manufacturer specific data Identification no medium primary address pulse increment pulse unit initial counter tariff mode date time and next due date can be parameterized via SND_UD through M Bus or optical interface 20 25 09 01 Version 1 4 PadPuls M4 User Manual
22. the M Bus output of the level converter Please start the file MBCONF_SETUP EXE from Windows Explorer or via Start Execute to install the software from version 1 40 up Subsequently you select the language of the installation procedure The setup software can create a program group and a link on the desktop on demand You can then execute both versions for German and English language either from start menu or desktop 3 2 Operation After program start the user operates the software according to the Windows conventions with the mouse or the keyboard If you stay with the mouse on a button or an input field then a hint to its function appears Light grey fields and boxes are not capable for editing All input fields and buttons have an underlined letter The function can be activated by simultaneous pressing of the keys ALT and the respective letter Within dialogs the Cursor can be moved with the keys TAB or SHIFT TAB forwards and back SPACE activates or deactivates selection boxes Multiple selection boxes arrow at the right edge can be activated with The user then selects an entry with and f By pressing RETURN the selected entry is taken over With ESC the selection box is left without transfer The program is arranged as a sheet system The sheet Info contains general options of the communication with the M Bus device to be configured In this sheet the user can select the serial port of th
23. to use 2 wire cables twisted pair NYM or j Y St Y with a max length of 10m In any case it must be noted that the total capacity of the cable plus impulse generator attached at any port may not exceed 2nF optional 12nF with activated long pulse sampling PadPulsM4 Relay mk M G WhJ m Display Toggle 60 MM C Port 4 Port 3 Port 2 Pong s0 00000000080 000006 M Bus 001234 8 001 234 8 m3 e f not all ports of PadPulse M4 are used you should not attach a cable to the respective unused port The capacity of an open circuited cable reduces the lifetime of the battery in stand alone operation no M Bus available e Ifthe pulse frequency is over 14 Hz false countings can occur e The PadPuls M4 is supplied from M Bus if it is available In this normal state the internal battery is then not loaded Only if the M Bus fails the battery takes over automatically the supply There is no lost of data and the counting function is continued The PadPuls M4 draws approximately 2 75mA current maximum 2 unit loads from the M Bus 4 25 09 01 Version 1 4 PadPuls M4 User Manual Oy Q GmbH Stettiner Str 38 D 33106 Paderborn The following graph represents the diagram of connections in the tariff mode with two counters and two tariff signal generators PadPulsM4 Relay mk M G WhJ I

Download Pdf Manuals

image

Related Search

Related Contents

Tsung User`s manual  modelo 4381  取扱説明書  Messa in funzione  Tyco 579-769 User's Manual  RielloMini rev8.indd  Règlement jeu OSS 117  レイのカタログ  Kawasaki 840015 User's Manual  Attuatori multigiro SA 07.1 – SA 16.1/SAR 07.1 – SAR 16.1 AUMA  

Copyright © All rights reserved.
Failed to retrieve file